Application A has registered a diag buffer and looking for particular event
to happen to release & read the trace buffer. Meanwhile application B has
unregistered the diag buffer and now Application A can't get the required
diag buffer. So proper diag buffer ownership is missing.
Each application has to maintain its own Unique ID. Now driver has to save
the Application's UniqueID for each diag buffer type when diag buffer is
registered. And driver has to allow 'release', 'read' & 'unregister' diag
commands only if application's UniqueID matches with saved UniqueID for the
corresponding diag buffer type.
When diag buffer is registered by the driver, then the UniqueID saved by
the driver is "BRCM" (i.e. 0x4252434D) for SAS3 and above generations HBA
devices. For SAS2 HBAs, driver keeps the legacy UniqueID 0x07075900 for
maintaining compatibility with the legacy SAS2 application and this
improvement won't be applicable for SAS2 HBA devices.
Any application can own the buffer registered by the driver by sending
diag register request to driver with same buffer type and size
(Application can get the buffer size by sending 'query' command). Then
driver changes the ownership of the buffer by saving application's
UniqueID for that corresponding buffer type.
Also, application can re-register the diag buffer with same size without
un-registering it, but diag buffer should be released before re-registering
it. By allowing this, driver no need to deallocate and allocate a new
buffer for re-register command, same buffer can be re-used.
Link: https://lore.kernel.org/r/1568379890-18347-6-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Memory leak can happen when diag buffer is released but not unregistered
(where buffer is deallocated) by the user. During module unload time driver
is not deallocating the buffer if the buffer is in released state.
Deallocate the diag buffer during module unload time without any diag
buffer status checks.
Link: https://lore.kernel.org/r/1568379890-18347-5-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When user issues diag register command from application with required size,
and if driver unable to allocate the memory, then it will fail the register
command. While failing the register command, driver is not currently
clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set
before trying to allocate the memory. As this bit is set, subsequent
register command will be failed with BUSY status even when user wants to
register the trace buffer will less memory.
Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag
register command with no memory status.
Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display message before releasing the diag buffer so that user knows which
event caused the release of diag buffer.
Releasing of diag buffer means HBA firmware stops posting the firmware logs
on the registered diag buffer.
Link: https://lore.kernel.org/r/1568379890-18347-3-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if user wishes to enable the host trace buffer during driver load
time, then user has to load the driver with module parameter
'diag_buffer_enable' set to one.
Alternatively now the user can enable host trace buffer by enabling the
following fields in manufacturing page11 in NVDATA (nvdata xml is used
while building HBA firmware image):
* HostTraceBufferMaxSizeKB - Maximum trace buffer size in KB that host can
allocate,
* HostTraceBufferMinSizeKB - Minimum trace buffer size in KB atleast host
should allocate,
* HostTraceBufferDecrementSizeKB - size by which host can reduce from
buffer size and retry the buffer allocation
when buffer allocation failed with previous
calculated buffer size.
The driver will register the trace buffer automatically without any module
parameter during boot time when above fields are enabled in manufacturing
page11 in HBA firmware.
Driver follows the following algorithm for enabling the host trace buffer
during driver load time:
* If user has loaded the driver with module parameter 'diag_buffer_enable'
set to one, then driver allocates 2MB buffer and registers this buffer
with HBA firmware for capturing the firmware trace logs.
* Else driver reads manufacture page11 data and checks whether
HostTraceBufferMaxSizeKB filed is zero or not?
- If HostTraceBufferMaxSizeKB is non-zero then driver tries to allocate
HostTraceBufferMaxSizeKB size of memory. If the buffer allocation is
successful, then it will register this buffer with HBA firmware, else
in a loop the driver will try again by reducing the current buffer size
with HostTraceBufferDecrementSizeKB size until memory allocation is
successful or buffer size falls below HostTraceBufferMinSizeKB. If the
memory allocation is successful, then the buffer will be registered
with the firmware. Else, if the buffer size falls below the
HostTraceBufferMinSizeKB, then driver won't register trace buffer with
HBA firmware.
- If HostTraceBufferMaxSizeKB is zero, then driver won't register trace
buffer with HBA firmware.
Link: https://lore.kernel.org/r/1568379890-18347-2-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Local variable fcp_txcmplq_cnt is initialized to 0 and then displayed in
lpfc driver message 0387.
Presumed residual (or unused) code from previous commit.
Removed fcp_txcmplq_cnt.
Link: https://lore.kernel.org/r/20190922035906.10977-20-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
T10 PI support on SLI-4-based FCoE adapters is not supported. A prior
commit in the 12.4.0.0 stream added device recognition that would prevent
T10 PI enablement. However, it didn't contain a complete device list. Thus
some SLI-4 FCoE adapters still had T10 PI enabled.
Fix by expanding the device list that identifies FCoE devices.
Link: https://lore.kernel.org/r/20190922035906.10977-19-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch updates ACQE handling for:
- an EEPROM failure error reported by the adapter.
- ensures that all data for any ACQE, recognized or not, is logged.
- Given that all data is now logged unconditionally, the default case
(unrecognized) data can be reduced.
Link: https://lore.kernel.org/r/20190922035906.10977-18-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_release_io_buf, an lpfc_io_buf is returned to the 'available' pool
before any associated sgl or cmd and rsp buffers are returned via their
respective 'put' routines. If xri rebalancing occurs and an lpfc_io_buf
structure is reused quickly, there may be a race condition between release
of old and association of new resources.
Re-ordered lpfc_release_io_buf to release sgl and cmd/rsp
buffer lists before releasing the lpfc_io_buf structure for re-use.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20190922035906.10977-17-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the sgl-per-hdwq paths are locking with spin_lock_irq() and
spin_unlock_irq() and may unwittingly raising irq when it shouldn't. Hard
deadlocks were seen around lpfc_scsi_prep_cmnd().
Fix by converting the locks to irqsave/irqrestore.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20190922035906.10977-16-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reviewing the CT behavior, issues with spinlock_irq were seen. The
driver should be using spinlock_irqsave/irqrestore in the els flush
routine.
Changed to spinlock_irqsave/irqrestore.
Link: https://lore.kernel.org/r/20190922035906.10977-15-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After study, it was determined there was a double free of a CT iocb during
execution of lpfc_offline_prep and lpfc_offline. The prep routine issued
an abort for some CT iocbs, but the aborts did not complete fast enough for
a subsequent routine that waits for completion. Thus the driver proceeded
to lpfc_offline, which releases any pending iocbs. Unfortunately, the
completions for the aborts were then received which re-released the ct
iocbs.
Turns out the issue for why the aborts didn't complete fast enough was not
their time on the wire/in the adapter. It was the lpfc_work_done routine,
which requires the adapter state to be UP before it calls
lpfc_sli_handle_slow_ring_event() to process the completions. The issue is
the prep routine takes the link down as part of it's processing.
To fix, the following was performed:
- Prevent the offline routine from releasing iocbs that have had aborts
issued on them. Defer to the abort completions. Also means the driver
fully waits for the completions. Given this change, the recognition of
"driver-generated" status which then releases the iocb is no longer
valid. As such, the change made in the commit 296012285c is reverted.
As recognition of "driver-generated" status is no longer valid, this
patch reverts the changes made in
commit 296012285c ("scsi: lpfc: Fix leak of ELS completions on adapter reset")
- Modify lpfc_work_done to allow slow path completions so that the abort
completions aren't ignored.
- Updated the fdmi path to recognize a CT request that fails due to the
port being unusable. This stops FDMI retries. FDMI will be restarted on
next link up.
Link: https://lore.kernel.org/r/20190922035906.10977-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scenarios were seen where a host hung when the system booted or the host
was very slow in booting. The link would not come up and no luns were
visible to the host.
After investigation, this was found to be due to the introduction of a new
ACQE that adapter may generate to report a adapter hw warning. The ACQE was
delivered to the driver very early in adapter initialization, when the
driver did not expect command completion. As part of handling this
unexpected interrupt the an EQEs are consumed and discarded and the EQ
rearmed. The issue is the CQ that cause the EQE and thus the interrupt was
not processed and the CQ was left unarmed. Meaning it would no longer
generate a new interrupt condition. Subsequent mailbox commands used to
initialize the adapter use the same CQ, and as there was no completion
interrupt generated, the driver never saw the mailbox commands complete and
it would wait long command timeouts.
Fix by having the early flush routine also process the related CQ and rearm
the CQ.
Link: https://lore.kernel.org/r/20190922035906.10977-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged several scenarios where checking of null pointer values
wasn't consistent.
Fix the code to that be consistent on checking.
Link: https://lore.kernel.org/r/20190922035906.10977-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the port, running as a nvme target, receives an ABTS, it submits
commands to the adapter to Abort i/o outstanding in the adapter. The Abort
command formatting routine left a command field set to zero, which
instructs the adapter to generate an ABTS on the wire as part of cleaning
up the I/O. This is common operation for an initiator, but not for a
target.
Fix the driver to check whether an ABTS had been received for the I/O, and
if so, change the Abort command formatting so that the ABTS generation is
disabled (IA=1). No need to ABTS it when the other side already has.
Also refactored the code such that there is a single routine being used for
nvme or nvmet ABORT requests, and IA is an argument.
Link: https://lore.kernel.org/r/20190922035906.10977-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An issue was seen discovering all SCSI Luns when a target device undergoes
link bounce.
The driver currently does not qualify the FC4 support on the target.
Therefore it will send a SCSI PRLI and an NVMe PRLI. The expectation is
that the target will reject the PRLI if it is not supported. If a PRLI
times out, the driver will retry. The driver will not proceed with the
device until both SCSI and NVMe PRLIs are resolved. In the failure case,
the device is FCP only and does not respond to the NVMe PRLI, thus
initiating the wait/retry loop in the driver. During that time, a RSCN is
received (device bounced) causing the driver to issue a GID_FT. The GID_FT
response comes back before the PRLI mess is resolved and it prematurely
cancels the PRLI retry logic and leaves the device in a STE_PRLI_ISSUE
state. Discovery with the target never completes or resets.
Fix by resetting the node state back to STE_NPR_NODE when GID_FT completes,
thereby restarting the discovery process for the node.
Link: https://lore.kernel.org/r/20190922035906.10977-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Faults are seen with RIP of lpfc_scsi_cmd_iocb_cmpl(). The failure is when
lpfc_update_status is being called as part of the completion. After
debugging, it was seen the issue was the shost pointer that the driver
derived from the scsi cmd. The crash showed the cmd->device pointer being
bogus, which is likely as the scsi devices were offlined prior. The bogus
device pointer caused subsequent pointers derived from the location,
specifically the vport, to be bogus.
Fix by adjusting the calling sequence to pass in the vport rather than
having to derive it from the cmd structure.
Link: https://lore.kernel.org/r/20190922035906.10977-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When target-side fault injections are made, the driver isn't reconnecting
to the remote port. The driver is logging "2753" error messages which
state:
"PLOGI failure DID:1B2400 Status:x3/xf0240008"
The failures status is indicating a Illegal field error, which points to
the Temporary RPI field being used for the ELS. This error typically means
the driver used an RPI that was already registered (shouldn't be registered
if using it in this context).
Study has found that if the driver were in discovery attempts and
encountered an error, it wouldn't flag the temporary rpi in error. Yet the
rpi was released for reallocation in these error paths and another ELS
could allocate the rpi. In the failure situation a retry was done on an ELS
that had encountered an error, and as the rpi wasn't marked in error, the
ELS reused the rpi it originally allocated. But that rpi had been allocated
by a different ELS issued after the original error and before the retry
attempt. The different ELS had succeeded and the RPI was registered.
Fix by marking the rpi state for the node to be in error, aka as needing
reallocation, upon an error in the els processing. Error state marking is
always done prior to release back to the internal rpi free list, which the
driver wasn't doing in cases prior.
Also enhanced some of the logging to help in the next case of problem
troubleshooting.
Link: https://lore.kernel.org/r/20190922035906.10977-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior use-after-free mailbox fix solved it's problem by null'ing a ndlp
pointer. However, further testing has shown that this change causes a
later state change to occasionally be skipped, which results in a reference
count never being decremented thus the rpi is never released, which causes
a vport delete to never succeed.
Revise the fix in the prior patch to no longer null the ndlp. Instead the
RELEASE_RPI flag is set which will drive the release of the rpi.
Given the new code was added at a deep indentation level, refactor the code
block using a new routine that avoids the indentation issues.
Fixes: 9b16406864 ("scsi: lpfc: Fix use-after-free mailbox cmd completion")
Link: https://lore.kernel.org/r/20190922035906.10977-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvme-fc transport may call to abort an io on controller reset. If the
driver is out of resources to issue an abort command, it just gives up and
does nothing. The transport expects the lldd to always be able to terminate
an io it has issued. At that point, the controller hangs waiting for
aborted ios to be returned. Note: flaged by "6136" and "6176" error
messages.
Root issue was the adapter mis-allocated the number resources it allocated
for command entries for the adapter.
Convert the driver to allocate command resources based on the number of
xris supported by the FC port - 1 resource for the original command and 1
resource for the abort request.
Link: https://lore.kernel.org/r/20190922035906.10977-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged missing status check on register read that flags a
poisoned data return value.
Add checking of register read status.
Link: https://lore.kernel.org/r/20190922035906.10977-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use of spin_lock_irq may re-enable interrupts prematurely.
Convert to spin_lock. Note: code is under the phba->hba_lock which has been
locked with irqsave.
Link: https://lore.kernel.org/r/20190922035906.10977-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After exchanging PLOGI on an SLI-3 adapter, the PRLI exchange failed. Link
trace showed the port was assigned a non-zero n_port_id, but didn't use the
address on the PRLI. The assigned address is set on the port by the
CONFIG_LINK mailbox command. The driver responded to the PRLI before the
mailbox command completed. Thus the PRLI response used the old n_port_id.
Defer the PRLI response until CONFIG_LINK completes.
Link: https://lore.kernel.org/r/20190922035906.10977-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The speed divisor is used in a context expecting an s64, but it is
evaluated using 32-bit arithmetic.
To avoid that happening, instead of multiplying by 1,000,000 in the
first place, simplify the fraction and do a standard 32 bit division
instead.
Fixes: f04b514c0c ("taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte")
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sja1105_static_config_upload, in two cases memory is leaked: when
static_config_buf_prepare_for_upload fails and when sja1105_inhibit_tx
fails. In both cases config_buf should be released.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Fixes: 1a4c69406c ("net: dsa: sja1105: Prevent PHY jabbering during switch reset")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg reports lots of modpost warnings on ARCH=um builds:
WARNING: "rename" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "lseek" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "ftruncate64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "getuid" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "lseek64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "unlink" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "pwrite64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "close" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "opendir" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "pread64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "syscall" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "readdir" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "readdir64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "futimes" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__lxstat" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "write" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "closedir" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__xstat" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "fsync" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__lxstat64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__fxstat64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "telldir" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "printf" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "readlink" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__sprintf_chk" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "link" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "rmdir" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "fdatasync" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "truncate" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "statfs" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__errno_location" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__xmknod" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "open64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "truncate64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "open" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "read" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "chown" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "chmod" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "utime" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "fchmod" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "seekdir" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "ioctl" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "dup2" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "statfs64" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "utimes" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "mkdir" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "fchown" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__guard" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "symlink" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "access" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "__stack_smash_handler" [vmlinux] is a static EXPORT_SYMBOL
When you run "make", the modpost is run twice; before linking vmlinux,
and before building modules. All the warnings above are from the second
modpost.
The offending symbols are defined not in vmlinux, but in the C library.
The first modpost is run against the relocatable vmlinux.o, and those
warnings are nicely suppressed because the SH_UNDEF entries from the
symbol table clear the ->is_static flag.
The second modpost is run against the executable vmlinux (+ modules),
where those symbols have been resolved, but the definitions do not
exist.
This commit fixes it in a straightforward way; suppress the static
EXPORT_SYMBOL warnings from "vmlinux".
Without this commit, we see valid warnings twice anyway. For example,
ARCH=arm64 defconfig shows the following warning twice:
WARNING: "HYPERVISOR_platform_op" [vmlinux] is a static EXPORT_SYMBOL_GPL
So, it is reasonable to suppress the second one.
Fixes: 15bfc2348d ("modpost: check for static EXPORT_SYMBOL* functions")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Denis Efremov <efremov@linux.com>
Minor formatting fixup.
Fixes: cd238effef ("docs: kbuild: convert docs to ReST and rename to *.rst")
Signed-off-by: Alex Gaynor <alex.gaynor@gmail.com>
Signed-off-by: Matthew Garrett <mjg59@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Sometimes the PTP synchronization on the switch 'jumps':
ptp4l[11241.155]: rms 8 max 16 freq -21732 +/- 11 delay 742 +/- 0
ptp4l[11243.157]: rms 7 max 17 freq -21731 +/- 10 delay 744 +/- 0
ptp4l[11245.160]: rms 33592410 max 134217731 freq +192422 +/- 8530253 delay 743 +/- 0
ptp4l[11247.163]: rms 811631 max 964131 freq +10326 +/- 557785 delay 743 +/- 0
ptp4l[11249.166]: rms 261936 max 533876 freq -304323 +/- 126371 delay 744 +/- 0
ptp4l[11251.169]: rms 48700 max 57740 freq -20218 +/- 30532 delay 744 +/- 0
ptp4l[11253.171]: rms 14570 max 30163 freq -5568 +/- 7563 delay 742 +/- 0
ptp4l[11255.174]: rms 2914 max 3440 freq -22001 +/- 1667 delay 744 +/- 1
ptp4l[11257.177]: rms 811 max 1710 freq -22653 +/- 451 delay 744 +/- 1
ptp4l[11259.180]: rms 177 max 218 freq -21695 +/- 89 delay 741 +/- 0
ptp4l[11261.182]: rms 45 max 92 freq -21677 +/- 32 delay 742 +/- 0
ptp4l[11263.186]: rms 14 max 32 freq -21733 +/- 11 delay 742 +/- 0
ptp4l[11265.188]: rms 9 max 14 freq -21725 +/- 12 delay 742 +/- 0
ptp4l[11267.191]: rms 9 max 16 freq -21727 +/- 13 delay 742 +/- 0
ptp4l[11269.194]: rms 6 max 15 freq -21726 +/- 9 delay 743 +/- 0
ptp4l[11271.197]: rms 8 max 15 freq -21728 +/- 11 delay 743 +/- 0
ptp4l[11273.200]: rms 6 max 12 freq -21727 +/- 8 delay 743 +/- 0
ptp4l[11275.202]: rms 9 max 17 freq -21720 +/- 11 delay 742 +/- 0
ptp4l[11277.205]: rms 9 max 18 freq -21725 +/- 12 delay 742 +/- 0
Background: the switch only offers partial RX timestamps (24 bits) and
it is up to the driver to read the PTP clock to fill those timestamps up
to 64 bits. But the PTP clock readout needs to happen quickly enough (in
0.135 seconds, in fact), otherwise the PTP clock will wrap around 24
bits, condition which cannot be detected.
Looking at the 'max 134217731' value on output line 3, one can see that
in hex it is 0x8000003. Because the PTP clock resolution is 8 ns,
that means 0x1000000 in ticks, which is exactly 2^24. So indeed this is
a PTP clock wraparound, but the reason might be surprising.
What is going on is that sja1105_tstamp_reconstruct(priv, now, ts)
expects a "now" time that is later than the "ts" was snapshotted at.
This, of course, is obvious: we read the PTP time _after_ the partial RX
timestamp was received. However, the workqueue is processing frames from
a skb queue and reuses the same PTP time, read once at the beginning.
Normally the skb queue only contains one frame and all goes well. But
when the skb queue contains two frames, the second frame that gets
dequeued might have been partially timestamped by the RX MAC _after_ we
had read our PTP time initially.
The code was originally like that due to concerns that SPI access for
PTP time readout is a slow process, and we are time-constrained anyway
(aka: premature optimization). But some timing analysis reveals that the
time spent until the RX timestamp is completely reconstructed is 1 order
of magnitude lower than the 0.135 s deadline even under worst-case
conditions. So we can afford to read the PTP time for each frame in the
RX timestamping queue, which of course ensures that the full PTP time is
in the partial timestamp's future.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 40df759e2b ("kbuild: Fix build with binutils <= 2.19")
introduced ar-option and KBUILD_ARFLAGS to deal with old binutils.
According to Documentation/process/changes.rst, the current minimal
supported version of binutils is 2.21 so you can assume the 'D' option
is always supported. Not only GNU ar but also llvm-ar supports it.
With the 'D' option hard-coded, there is no more user of ar-option
or KBUILD_ARFLAGS.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2019-09-28
An update from ieee802154 for your *net* tree.
Three driver fixes. Navid Emamdoost fixed a memory leak on an error
path in the ca8210 driver, Johan Hovold fixed a use-after-free found
by syzbot in the atusb driver and Christophe JAILLET makes sure
__skb_put_data is used instead of memcpy in the mcr20a driver
I switched from branches to tags here to be pulled from. So far not
annotated and not signed. Once I fixed my scripts it should contain
this messages as annotations. If you want it signed as well just tell
me. If there are any problems let me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The "reuse->sock[]" array is shared by multiple sockets. The going away
sk must unpublish itself from "reuse->sock[]" before making call_rcu()
call. However, this unpublish-action is currently done after a grace
period and it may cause use-after-free.
The fix is to move reuseport_detach_sock() to sk_destruct().
Due to the above reason, any socket with sk_reuseport_cb has
to go through the rcu grace period before freeing it.
It is a rather old bug (~3 yrs). The Fixes tag is not necessary
the right commit but it is the one that introduced the SOCK_RCU_FREE
logic and this fix is depending on it.
Fixes: a4298e4522 ("net: add SOCK_RCU_FREE socket flag")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously KUnit assumed that printk would always be present, which is
not a valid assumption to make. Fix that by removing call to
vprintk_emit, and calling printk directly.
This fixes a build error[1] reported by Randy.
For context this change comes after much discussion. My first stab[2] at
this was just to make the KUnit logging code compile out; however, it
was agreed that if we were going to use vprintk_emit, then vprintk_emit
should provide a no-op stub, which lead to my second attempt[3]. In
response to me trying to stub out vprintk_emit, Sergey Senozhatsky
suggested a way for me to remove our usage of vprintk_emit, which led to
my third attempt at solving this[4].
In my third version of this patch[4], I completely removed vprintk_emit,
as suggested by Sergey; however, there was a bit of debate over whether
Sergey's solution was the best. The debate arose due to Sergey's version
resulting in a checkpatch warning, which resulted in a debate over
correct printk usage. Joe Perches offered an alternative fix which was
somewhat less far reaching than what Sergey had suggested and
importantly relied on continuing to use %pV. Much of the debated
centered around whether %pV should be widely used, and whether Sergey's
version would result in object size bloat. Ultimately, we decided to go
with Sergey's version.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Link[1]: https://lore.kernel.org/linux-kselftest/c7229254-0d90-d90e-f3df-5b6d6fc0b51f@infradead.org/
Link[2]: https://lore.kernel.org/linux-kselftest/20190827174932.44177-1-brendanhiggins@google.com/
Link[3]: https://lore.kernel.org/linux-kselftest/20190827234835.234473-1-brendanhiggins@google.com/
Link[4]: https://lore.kernel.org/linux-kselftest/20190828093143.163302-1-brendanhiggins@google.com/
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Tim.Bird@sony.com
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add entry for the new proc sysctl KUnit test to the PROC SYSCTL section,
and add Iurii as a maintainer.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
KUnit tests for initialized data behavior of proc_dointvec that is
explicitly checked in the code. Includes basic parsing tests including
int min/max overflow.
Signed-off-by: Iurii Zaikin <yzaikin@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add documentation for KUnit, the Linux kernel unit testing framework.
- Add intro and usage guide for KUnit
- Add API reference
Signed-off-by: Felix Guo <felixguoxiuping@gmail.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add defconfig for UML and a fragment that can be used to configure other
architectures for building KUnit tests. Add option to kunit_tool to use
a defconfig to create the kunitconfig.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The ultimate goal is to create minimal isolated test binaries; in the
meantime we are using UML to provide the infrastructure to run tests, so
define an abstract way to configure and run tests that allow us to
change the context in which tests are built without affecting the user.
This also makes pretty and dynamic error reporting, and a lot of other
nice features easier.
kunit_config.py:
- parse .config and Kconfig files.
kunit_kernel.py: provides helper functions to:
- configure the kernel using kunitconfig.
- build the kernel with the appropriate configuration.
- provide function to invoke the kernel and stream the output back.
kunit_parser.py: parses raw logs returned out by kunit_kernel and
displays them in a user friendly way.
test_data/*: samples of test data for testing kunit.py, kunit_config.py,
etc.
Signed-off-by: Felix Guo <felixguoxiuping@gmail.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add unit tests for KUnit managed resources. KUnit managed resources
(struct kunit_resource) are resources that are automatically cleaned up
at the end of a KUnit test, similar to the concept of devm_* managed
resources.
Signed-off-by: Avinash Kondareddy <akndr41@gmail.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add support for assertions which are like expectations except the test
terminates if the assertion is not satisfied.
The idea with assertions is that you use them to state all the
preconditions for your test. Logically speaking, these are the premises
of the test case, so if a premise isn't true, there is no point in
continuing the test case because there are no conclusions that can be
drawn without the premises. Whereas, the expectation is the thing you
are trying to prove. It is not used universally in x-unit style test
frameworks, but I really like it as a convention. You could still
express the idea of a premise using the above idiom, but I think
KUNIT_ASSERT_* states the intended idea perfectly.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add KUnit tests for the KUnit test abort mechanism (see preceding
commit). Add tests both for general try catch mechanism as well as
non-architecture specific mechanism.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add support for aborting/bailing out of test cases, which is needed for
implementing assertions.
An assertion is like an expectation, but bails out of the test case
early if the assertion is not met. The idea with assertions is that you
use them to state all the preconditions for your test. Logically
speaking, these are the premises of the test case, so if a premise isn't
true, there is no point in continuing the test case because there are no
conclusions that can be drawn without the premises. Whereas, the
expectation is the thing you are trying to prove.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fix the following warning seen on GCC 7.3:
kunit/test-test.o: warning: objtool: kunit_test_unsuccessful_try() falls through to next function kunit_test_catch()
kunit_try_catch_throw is a function added in the following patch in this
series; it allows KUnit, a unit testing framework for the kernel, to
bail out of a broken test. As a consequence, it is a new __noreturn
function that objtool thinks is broken (as seen above). So fix this
warning by adding kunit_try_catch_throw to objtool's noreturn list.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://www.spinics.net/lists/linux-kbuild/msg21708.html
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add a test for string stream along with a simpler example.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
KUnit is a new unit testing framework for the kernel and when used is
built into the kernel as a part of it. Add KUnit to the lib Kconfig and
Makefile to allow it to be actually built.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add support for expectations, which allow properties to be specified and
then verified in tests.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add `struct kunit_assert` and friends which provide a structured way to
capture data from an expectation or an assertion (introduced later in
the series) so that it may be printed out in the event of a failure.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
