The patch adds driver support for configuring the grc dump config flags.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver support for dumping the config id attributes via ethtool dump
interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for reading the config id attributes from NVM
flash partition.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Dynamic toggling of vlan_filtering for SJA1105 DSA
This patchset addresses a limitation in dsa_8021q where this sequence of
commands was causing the switch to stop forwarding traffic:
ip link add name br0 type bridge vlan_filtering 0
ip link set dev swp2 master br0
echo 1 > /sys/class/net/br0/bridge/vlan_filtering
echo 0 > /sys/class/net/br0/bridge/vlan_filtering
The issue has to do with the VLAN table manipulations that dsa_8021q
does without notifying the bridge layer. The solution is to always
restore the VLANs that the bridge knows about, when disabling tagging.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge core assumes that enabling/disabling vlan_filtering will
translate into the simple toggling of a flag for switchdev drivers.
That is clearly not the case for sja1105, which alters the VLAN table
and the pvids in order to obtain port separation in standalone mode.
There are 2 parts to the issue.
First, tag_8021q changes the pvid to a unique per-port rx_vid for frame
identification. But we need to disable tag_8021q when vlan_filtering
kicks in, and at that point, the VLAN configured as pvid will have to be
removed from the filtering table of the ports. With an invalid pvid, the
ports will drop all traffic. Since the bridge will not call any vlan
operation through switchdev after enabling vlan_filtering, we need to
ensure we're in a functional state ourselves. Hence read the pvid that
the bridge is aware of, and program that into our ports.
Secondly, tag_8021q uses the 1024-3071 range privately in
vlan_filtering=0 mode. Had the user installed one of these VLANs during
a previous vlan_filtering=1 session, then upon the next tag_8021q
cleanup for vlan_filtering to kick in again, VLANs in that range will
get deleted unconditionally, hence breaking user expectation. So when
deleting the VLANs, check if the bridge had knowledge about them, and if
it did, re-apply the settings. Wrap this logic inside a
dsa_8021q_vid_apply helper function to reduce code duplication.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this simplified code snippet fails:
br_vlan_get_pvid(netdev, &pvid);
br_vlan_get_info(netdev, pvid, &vinfo);
ASSERT(!(vinfo.flags & BRIDGE_VLAN_INFO_PVID));
It is intuitive that the pvid of a netdevice should have the
BRIDGE_VLAN_INFO_PVID flag set.
However I can't seem to pinpoint a commit where this behavior was
introduced. It seems like it's been like that since forever.
At a first glance it would make more sense to just handle the
BRIDGE_VLAN_INFO_PVID flag in __vlan_add_flags. However, as Nikolay
explains:
There are a few reasons why we don't do it, most importantly because
we need to have only one visible pvid at any single time, even if it's
stale - it must be just one. Right now that rule will not be violated
by this change, but people will try using this flag and could see two
pvids simultaneously. You can see that the pvid code is even using
memory barriers to propagate the new value faster and everywhere the
pvid is read only once. That is the reason the flag is set
dynamically when dumping entries, too. A second (weaker) argument
against would be given the above we don't want another way to do the
same thing, specifically if it can provide us with two pvids (e.g. if
walking the vlan list) or if it can provide us with a pvid different
from the one set in the vg. [Obviously, I'm talking about RCU
pvid/vlan use cases similar to the dumps. The locked cases are fine.
I would like to avoid explaining why this shouldn't be relied upon
without locking]
So instead of introducing the above change and making sure of the pvid
uniqueness under RCU, simply dynamically populate the pvid flag in
br_vlan_get_info().
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the register value width as the regmap_config name to prevent the
following error when the second and third regmap_configs are
initialized.
"debugfs: Directory '${bus-id}' with parent 'regmap' already present!"
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix OGM and OGMv2 header read boundary check,
by Sven Eckelmann (2 patches)
-----BEGIN PGP SIGNATURE-----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=hD2g
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20190830' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- Fix OGM and OGMv2 header read boundary check,
by Sven Eckelmann (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add Sven to the MAINTAINERS file, by Simon Wunderlich
-----BEGIN PGP SIGNATURE-----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=LAvx
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20190830' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This maintenance patchset includes the following patches:
- Add Sven to the MAINTAINERS file, by Simon Wunderlich
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9392bd98bb ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") and the commit 3316f99a9f ("tools/power
turbostat: Also read package power on AMD F17h (Zen)") add AMD Fam 17h
RAPL support.
Hygon Family 18h(Dhyana) support RAPL in bit 14 of CPUID 0x80000007 EDX,
and has MSRs RAPL_PWR_UNIT/CORE_ENERGY_STAT/PKG_ENERGY_STAT. So add Hygon
Dhyana Family 18h support for RAPL.
Already tested on Hygon multi-node systems and it shows correct per-core
energy usage and the total package power.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 9392bd98bb ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") add a function get_tdp_amd(), the parameter is CPU
family. But the rapl_probe_amd() function use wrong model parameter.
Fix the wrong caller parameter of get_tdp_amd() to use family.
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Len Brown <len.brown@intel.com>
In some case C1% will be wrong value, when platform doesn't have MSR for
C1 residency.
For example:
Core CPU CPU%c1
- - 100.00
0 0 100.00
0 2 100.00
1 1 100.00
1 3 100.00
But adding Busy% will fix this
Core CPU Busy% CPU%c1
- - 99.77 0.23
0 0 99.77 0.23
0 2 99.77 0.23
1 1 99.77 0.23
1 3 99.77 0.23
This issue can be reproduced on most of the recent systems including
Broadwell, Skylake and later.
This is because if we don't select Busy% or Avg_MHz or Bzy_MHz then
mperf value will not be read from MSR, so it will be 0. But this
is required for C1% calculation when MSR for C1 residency is not present.
Same is true for C3, C6 and C7 column selection.
So add another define DO_BIC_READ(), which doesn't depend on user
column selection and use for mperf, C3, C6 and C7 related counters.
So when there is no platform support for C1 residency counters,
we still read these counters, if the CPU has support and user selected
display of CPU%c1.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Turbostat works by taking a snapshot of counters, sleeping, taking another
snapshot, calculating deltas, and printing out the table.
The sleep time is controlled via -i option or by user sending a signal or a
character to stdin. In the latter case, turbostat always adds 1 ms
sleep before it reads the counters, in order to avoid larger imprecisions
in the results in prints.
While the 1 ms delay may be a good idea for a "dumb" user, it is a
problem for an "aware" user. I do thousands and thousands of measurements
over a short period of time (like 2ms), and turbostat unconditionally adds
a 1ms to my interval, so I cannot get what I really need.
This patch removes the unconditional 1ms sleep. This is an expert user
tool, after all, and non-experts will unlikely ever use it in the non-fixed
interval mode anyway, so I think it is OK to remove the 1ms delay.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit '47936f944e tools/power turbostat: fix printing on input' make
a valid fix, but it completely disabled piped stdin support, which is
a valuable use-case. Indeed, if stdin is a pipe, turbostat won't read
anything from it, so it becomes impossible to get turbostat output at
user-defined moments, instead of the regular intervals.
There is no reason why this should works for terminals, but not for
pipes. This patch improves the situation. Instead of ignoring pipes, we
read data from them but gracefully handle the EOF case.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This enables turbostat utility on Ice Lake NNPI SoC.
Link: https://lkml.org/lkml/2019/6/5/1034
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Perhaps if this more descriptive name had been used,
then we wouldn't have had the HSW ULT vs HSW CORE bug,
fixed by the previous commit.
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat: cpu0: msr offset 0x630 read failed: Input/output error
because Haswell Core does not have C8-C10.
Output C8-C10 only on Haswell ULT.
Fixes: f5a4c76ad7 ("tools/power turbostat: consolidate duplicate model numbers")
Reported-by: Prarit Bhargava <prarit@redhat.com>
Suggested-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat could be terminated by general protection fault on some latest
hardwares which (for example) support 9 levels of C-states and show 18
"tADDED" lines. That bloats the total output and finally causes buffer
overrun. So let's extend the buffer to avoid this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently the error return path does not close the file fp and leaks
a file descriptor. Fix this by closing the file.
Fixes: 5ea7647b33 ("tools/power turbostat: Warn on bad ACPI LPIT data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Turbostat currently normalizes TSC and other values by dividing by an
interval. This interval is the delta between the start of one global
(all counters on all CPUs) sampling and the start of another. However,
this introduces a lot of jitter into the data.
In order to reduce jitter, the interval calculation should be based on
timestamps taken per thread and close to the start of the thread's
sampling.
Define a per thread time value to hold the delta between samples taken
on the thread.
Use the timestamp taken at the beginning of sampling to calculate the
delta.
Move the thread's beginning timestamp to after the CPU migration to
avoid jitter due to the migration.
Use the global time delta for the average time delta.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The -w argument in x86_energy_perf_policy currently triggers an
unconditional segfault.
This is because the argument string reads: "+a:c:dD:E:e:f:m:M:rt:u:vw" and
yet the argument handler expects an argument.
When parse_optarg_string is called with a null argument, we then proceed to
crash in strncmp, not horribly friendly.
The man page describes -w as taking an argument, the long form
(--hwp-window) is correctly marked as taking a required argument, and the
code expects it.
As such, this patch simply marks the short form (-w) as requiring an
argument.
Signed-off-by: Zephaniah E. Loss-Cutler-Hull <zephaniah@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Compiling without optimisations is silly, especially since some
warnings depend on the optimiser. Use -O2.
Fortify adds warnings for unchecked I/O (among other things), which
seems to be a good idea for user-space code. Enable that too.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
x86_energy_perf_policy first uses __get_cpuid() to check the maximum
CPUID level and exits if it is too low. It then assumes that later
calls will succeed (which I think is architecturally guaranteed). It
also assumes that CPUID works at all (which is not guaranteed on
x86_32).
If optimisations are enabled, gcc warns about potentially
uninitialized variables. Fix this by adding an exit-on-error after
every call to __get_cpuid() instead of just checking the maximum
level.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull i2c fixes from Wolfram Sang:
"I2C has a bunch of driver fixes and a core improvement to make the
on-going API transition more robust"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mediatek: disable zero-length transfers for mt8183
i2c: iproc: Stop advertising support of SMBUS quick cmd
MAINTAINERS: i2c mv64xxx: Update documentation path
i2c: piix4: Fix port selection for AMD Family 16h Model 30h
i2c: designware: Synchronize IRQs when unregistering slave client
i2c: i801: Avoid memory leak in check_acpi_smo88xx_device()
i2c: make i2c_unregister_device() ERR_PTR safe
The name tracing_reset() was a misnomer, as it really only reset a single
CPU buffer. Rename it to tracing_reset_cpu() and also make it static and
remove the prototype from trace.h, as it is only used in a single function.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
As the max stack tracer algorithm is not that easy to understand from the
code, add comments that explain the algorithm and mentions how
ARCH_FTRACE_SHIFT_STACK_TRACER affects it.
Link: http://lkml.kernel.org/r/20190806123455.487ac02b@gandalf.local.home
Suggested-by: Joel Fernandes <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Most archs (well at least x86) store the function call return address on the
stack before storing the local variables for the function. The max stack
tracer depends on this in its algorithm to display the stack size of each
function it finds in the back trace.
Some archs (arm64), may store the return address (from its link register)
just before calling a nested function. There's no reason to save the link
register on leaf functions, as it wont be updated. This breaks the algorithm
of the max stack tracer.
Add a new define ARCH_FTRACE_SHIFT_STACK_TRACER that an architecture may set
if it stores the return address (link register) after it stores the
function's local variables, and have the stack trace shift the values of the
mapped stack size to the appropriate functions.
Link: 20190802094103.163576-1-jiping.ma2@windriver.com
Reported-by: Jiping Ma <jiping.ma2@windriver.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
cleanup() mostly frees/unmaps the malloc'd/privately-mapped
copy of the ELF file recordmcount is working on, which is
set up in mmap_file(). It also deals with positioning within
the pseduo prive-mapping of the file and appending to the ELF
file.
Split into two steps:
mmap_cleanup() for the mapping itself
file_append_cleanup() for allocations storing the
appended ELF data.
Also, move the global variable initializations out of the main,
per-object-file loop and nearer to the alloc/init (mmap_file())
and two cleanup functions so we can more clearly see how they're
related.
Link: http://lkml.kernel.org/r/2a387ac86d133d22c68f57b9933c32bab1d09a2d.1564596289.git.mhelsley@vmware.com
Signed-off-by: Matt Helsley <mhelsley@vmware.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Redundant cleanup calls were introduced when transitioning from
the old error/success handling via setjmp/longjmp -- the longjmp
ensured the cleanup() call only happened once but replacing
the success_file()/fail_file() calls with cleanup() meant that
multiple cleanup() calls can happen as we return from function
calls.
In do_file(), looking just before and after the "goto out" jumps we
can see that multiple cleanups() are being performed. We remove
cleanup() calls from the nested functions because it makes the code
easier to review -- the resources being cleaned up are generally
allocated and initialized in the callers so freeing them there
makes more sense.
Other redundant cleanup() calls:
mmap_file() is only called from do_file() and, if mmap_file() fails,
then we goto out and do cleanup() there too.
write_file() is only called from do_file() and do_file()
calls cleanup() unconditionally after returning from write_file()
therefore the cleanup() calls in write_file() are not necessary.
find_secsym_ndx(), called from do_func()'s for-loop, when we are
cleaning up here it's obvious that we break out of the loop and
do another cleanup().
__has_rel_mcount() is called from two parts of do_func()
and calls cleanup(). In theory we move them into do_func(), however
these in turn prove redundant so another simplification step
removes them as well.
Link: http://lkml.kernel.org/r/de197e17fc5426623a847ea7cf3a1560a7402a4b.1564596289.git.mhelsley@vmware.com
Signed-off-by: Matt Helsley <mhelsley@vmware.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Recordmcount uses setjmp/longjmp to manage control flow as
it reads and then writes the ELF file. This unusual control
flow is hard to follow and check in addition to being unlike
kernel coding style.
So we rewrite these paths to use regular return values to
indicate error/success. When an error or previously-completed object
file is found we return an error code following kernel
coding conventions -- negative error values and 0 for success when
we're not returning a pointer. We return NULL for those that fail
and return non-NULL pointers otherwise.
One oddity is already_has_rel_mcount -- there we use pointer comparison
rather than string comparison to differentiate between
previously-processed object files and returning the name of a text
section.
Link: http://lkml.kernel.org/r/8ba8633d4afe444931f363c8d924bf9565b89a86.1564596289.git.mhelsley@vmware.com
Signed-off-by: Matt Helsley <mhelsley@vmware.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add immediate string parameter (\"string") support to
probe events. This allows you to specify an immediate
(or dummy) parameter instead of fetching a string from
memory.
This feature looks odd, but imagine that you put a probe
on a code to trace some string data. If the code is
compiled into 2 instructions and 1 instruction has a
string on memory but other has no string since it is
optimized out. In that case, you can not fold those into
one event, even if ftrace supported multiple probes on
one event. With this feature, you can set a dummy string
like foo=\"(optimized)":string instead of something
like foo=+0(+0(%bp)):string.
Link: http://lkml.kernel.org/r/156095691687.28024.13372712423865047991.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add immediate value parameter (\1234) support to
probe events. This allows you to specify an immediate
(or dummy) parameter instead of fetching from memory
or register.
This feature looks odd, but imagine when you put a probe
on a code to trace some data. If the code is compiled into
2 instructions and 1 instruction has a value but other has
nothing since it is optimized out.
In that case, you can not fold those into one event, even
if ftrace supported multiple probes on one event.
With this feature, you can set a dummy value like
foo=\deadbeef instead of something like foo=%di.
Link: http://lkml.kernel.org/r/156095690733.28024.13258186548822649469.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add per-probe delete method from one event passing the head of
definition. In other words, the events which match the head
N parameters are deleted.
Link: http://lkml.kernel.org/r/156095689811.28024.221706761151739433.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Allow user to delete a probe from event. This is done by head
match. For example, if we have 2 probes on an event
$ cat kprobe_events
p:kprobes/testprobe _do_fork r1=%ax r2=%dx
p:kprobes/testprobe idle_fork r1=%ax r2=%cx
Then you can remove one of them by passing the head of definition
which identify the probe.
$ echo "-:kprobes/testprobe idle_fork" >> kprobe_events
Link: http://lkml.kernel.org/r/156095688848.28024.15798690082378432435.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Allow user to define several probes on one uprobe event.
Note that this only support appending method. So deleting
event will delete all probes on the event.
Link: http://lkml.kernel.org/r/156095687876.28024.13840331032234992863.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add multi-probe per one event support to kprobe events.
User can define several different probes on one trace event
if those events have same "event signature",
e.g.
# echo p:testevent _do_fork > kprobe_events
# echo p:testevent fork_idle >> kprobe_events
# kprobe_events
p:kprobes/testevent _do_fork
p:kprobes/testevent fork_idle
The event signature is defined by kprobe type (retprobe or not),
the number of args, argument names, and argument types.
Note that this only support appending method. Delete event
operation will delete all probes on the event.
Link: http://lkml.kernel.org/r/156095686913.28024.9357292202316540742.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pass extra arguments to match operation for checking
exact match. If the event doesn't support exact match,
it will be ignored.
Link: http://lkml.kernel.org/r/156095685930.28024.10405547027475590975.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When user gives an event name to delete, delete all
matched events instead of the first one.
This means if there are several events which have same
name but different group (subsystem) name, those are
removed if user passed only the event name, e.g.
# cat kprobe_events
p:group1/testevent _do_fork
p:group2/testevent fork_idle
# echo -:testevent >> kprobe_events
# cat kprobe_events
#
Link: http://lkml.kernel.org/r/156095684958.28024.16597826267117453638.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Split the trace_event related data from trace_probe data structure
and introduce trace_probe_event data structure for its folder.
This trace_probe_event data structure can have multiple trace_probe.
Link: http://lkml.kernel.org/r/156095683995.28024.7552150340561557873.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
uwrite() works within the pseudo-mapping and extends it as necessary
without needing the file descriptor (fd) parameter passed to it.
Similarly, ulseek() doesn't need its fd parameter. These parameters
were only added because the functions bear a conceptual resemblance
to write() and lseek(). Worse, they obscure the fact that at the time
uwrite() and ulseek() are called fd_map is not a valid file descriptor.
Remove the unused file descriptor parameters that make it look like
fd_map is still valid.
Link: http://lkml.kernel.org/r/2a136e820ee208469d375265c7b8eb28570749a0.1563992889.git.mhelsley@vmware.com
Signed-off-by: Matt Helsley <mhelsley@vmware.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
