[Why]
The register LVTMA_PWRSEQ_CNTL is used to determine the power state of the
embedded display. Currently we do not actually read this register's values,
so during power down we think that this display is already off, so we skip
calling into VBIOS to actually turn it off.
[How]
- add relevant fields to shift / mask initialization
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous workaround to prevent a vsync flip to be converted
to immediate flip is no longer needed, and is risky because
there are cases where it can result in infinite loop.
[how]
Remove wait loop (which is potentially infinite) before locking
pipe
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should be using the ddc_num from res_caps. As the
pipe count != number of i2c resources.
[How]
Use ddc_num from res_cap instead of pipe count.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, only the DCBx status is taken into account to
determine if FW LLDP is possible. But there are NVM version
coming out with DCBx enabled, and FW LLDP disabled. This
is causing errors where the driver sees that DCBx is not
disabled, and then tries to register for LLDP MIB change
events, and fails.
Change the logic to detect both DCBx and LLDP states in the
FW engine.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
[Why]
Existing HW Features, HW Diags test requested that the
registers be exposed.
[How]
Add V_TOTAL_MID to existing DC structures.
Make sure values are passed down throughout DC
Add Register definition.
Program the additional registers
Add additional Logic for V_TOTAL_CONTROL.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Calculating DCFCLK DS time requires calculating
delivery time for luma/chroma, but this value is
not calculated in DMLv2, it was inadvertently
removed when porting DMLv2
[how]
Add the calculation back
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM provides drm_dp_mst_dump_topology, which prints
useful information about MST devices
Hook this up to a debugfs file named amdgpu_mst_topology
Signed-off-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OS will reserve HW state in UEFI mode.
Driver init_hw reset to RGB which caused HDMI green in YCbCr mode.
read HW blank_color based on acc_mode.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A recent bug showed that logging would be useful in debugging
various gamma issues.
[How]
Add logging in dc.
Fix formatting for easier graphing.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] HW rotation is not enabled. Calculations for cursor rotation
are wrong for the values passed to set_cursor_position.
[How] Swap Src rect and height and vertically mirror surface for
the correct surface rotation direction. Cursor position is rotated
according to angle. Offset calculations are tweaked for non-rotated
cursor hotspot and width/height.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to have the ability to to tell us set degamma on the cursor.
[How]
Pass a flag down to register programming that tells us if the
current surface format needs cursor degamma.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update bw validation to use prev and next odm pipe pointers
for populating dml inputs.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to memset all odm pipes when calling dc_remove_stream_from_ctx
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn20 requires special casing for odm.
This change treats odm as alternative to mpc tree on dcn20.
This is planned to be fixed in a future refactor
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
num_slices_h was not being checked
[How]
Fix the typo and check num_slices_h
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ODM next and prev pipe were missing from dc_copy_state
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In newer hardware MANUAL_FLOW_CONTROL is not a trigger bit. Due to this
front porch is fixed and in these hardware freesync does not work.
[How]
Change the programming to generate a pulse so that the event will be
triggered, front porch will be cut short and freesync will work.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With visual confirm enabled, displays where ODM combine is enabled
has a test pattern stuck on the right half of the display even
though the display is unblanked.
[how]
Add a condition to not show the colour ramp test pattern when the
display is unblanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Video Timing Extended Metadata packet (VTEM) is not
specific to freesync. So move it out of freesync module
[How]
- Moved VTEM from freesync module to info_packet module
- Created new structure for VTEM parameters that can be used for VRR
and FVA
Signed-off-by: Ahmad Othman <ahmad.othman@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Ahmad Othman <Ahmad.Othman@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This function is not being used, it was left in
when introducing DCN2
[How]
Remove the function
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
during a refactor a redundant code that has unknown behaviour was added.
[how]
removed old bad code
Fixes: 8a31820b12 ("drm/amd/display: Make init_hw and init_pipes generic for seamless boot")
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How] Allocate memory for default page and program memory block addr
into default page addr register.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
IEEE OUI will now be used while referring to certain vendors.
instead of normal index
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before a statically allocated PPS data structure, that did
get zeroed-out at startup, had been re-used for making packed PPS
SDP. With S3 fix, using a non-initialized PPS data structure was
introduced, while wrongly assuming it'd get initialized before it's
populated. As a consequence 'vbr_enable' and perhaps some other
fields are left uninitialized when making packed PPS SDP. This can
affect 'simple_422' as well because of the way PPS SDP packing is
done (the fields are not masked first, only shifted). The behavior
will be different, depending on the content of uninitialized data.
[how]
Zero-out PPS data structure at initialization time before it's
populated
Fixes: 1a9e3d4569 ("drm/amd/display: Set DSC before DIG front-end is connected to its back-end")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add new function to get the voltage at the end of
dcn_validate_bandwidth, to check against the
highest voltage we allow.
Created a stub to allow for optimizations
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sun peng Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding NULL checks to various parameters in log_tf, to avoid
nullptr errors
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Nikola Cornij <Nikola.Cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the writeback Hratio and Vratio in dml.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous odm change broke stream enable by always setting
n_multiply as if odm was on.
This fixes the check for odm by making sure opp count is >1
rather than not 0.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ABM 2.3 firmware expects information in iRAM that differs from previous
versions of ABM, so a mechanism is required to provide it with that
information.
[How]
Extend the existing iRAM definition to include parameters added by
ABM 2.3, and load it if DMCU is running ABM 2.3.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With Scatter Gather enabled, HUBP underflows during MPO enabled video
playback. hubp_init has a register write that fixes this problem, but
the register is cleared when HUBP gets power gated.
[how]
Make a call to hubp_init during enable_plane, so that the fix can
be applied after HUBP powers back on again.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable_audio_stream gets enum option as a paramenter which will decide
if we free acquired resources or not. However checks for the option is
guarded by the other condition which check if audio stream is getting
diabled more than once. With both conditions combined, if we attempt to
disable audio stream twice in a row, first with keep and second with
free as an option, we will never free any resources, which will make
system think there is audio endpoint connected even after we plug out
the device
[How]
Get rid of option as parameter to disable_audio_stream and move the part
of the code that free acquired resources to outside where to keep or to
free resources is actually determined
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dig_encoder_sel_to_atom will always return zero on any ASIC version
past DCE80 since programming of the FE selection is handled by
driver, but the translation code was left in the function, making
it look like a coding error.
[How]
Remove code that has no effect, and replace with a comment describing
why it returns zero.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm is handled using top_bottom pipe by special casing
the differing opps to differentiate from mpc combine.
Since top/bottom pipe list was made to track mpc muxing this creates
difficulties in adding a 4 pipe odm case support.
Rather than continue using mpc combine list, this change reworks odm
to use it's own linked list to keep track of odm combine pipes. This
also opens up options for using mpo with odm, if a practical use case
is ever found.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that we properly handle them on older asics.
Fixes: 3ff985485b ("drm/amdgpu: Export function to flush TLB of specific vm hub")
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a dcfeaturemask flag for mclk switching. Disable by default;
enable once the feature has seen more testing.
Set amdgpu.dcfeaturemask=2 on the kernel command line in grub
to enable this.
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly set all_displays_in_sync so that when the data is
propagated to powerplay, it's set properly and we can enable
mclk switching when all monitors are in sync.
v2: fix logic, clean up
v3: check for blending chains, simplify logic
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If DC has synced the displays, we can enable mclk switching to
save power.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If DC has synced the displays, we can enable mclk switching to
save power.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the 40.46 SMU release, they changed CurrSocketPower to
AverageSocketPower, but this was changed back in 40.47 so just check if
it's 40.46 and make the appropriate change
Tested with 40.45, 40.46 and 40.47 successfully
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the virtual function PCI device id.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Frank.Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix other navi asic set peak performance level error.
because the navi10_ppt.c will handle navi12 14 asic,
it will use navi10 peak value to set other asic, it is not correct.
after patch:
only navi10 use custom peak value, other asic will used default value.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use unsigned long type for the same ras count variable.
This will avoid overflow on 64 bit system.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
At the moment we initialise the target *mask* of a virtual IRQ to the
VCPU it belongs to, even though this mask is only defined for GICv2 and
quickly runs out of bits for many GICv3 guests.
This behaviour triggers an UBSAN complaint for more than 32 VCPUs:
------
[ 5659.462377] UBSAN: Undefined behaviour in virt/kvm/arm/vgic/vgic-init.c:223:21
[ 5659.471689] shift exponent 32 is too large for 32-bit type 'unsigned int'
------
Also for GICv3 guests the reporting of TARGET in the "vgic-state" debugfs
dump is wrong, due to this very same problem.
Because there is no requirement to create the VGIC device before the
VCPUs (and QEMU actually does it the other way round), we can't safely
initialise mpidr or targets in kvm_vgic_vcpu_init(). But since we touch
every private IRQ for each VCPU anyway later (in vgic_init()), we can
just move the initialisation of those fields into there, where we
definitely know the VGIC type.
On the way make sure we really have either a VGICv2 or a VGICv3 device,
since the existing code is just checking for "VGICv3 or not", silently
ignoring the uninitialised case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Dave Martin <dave.martin@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Multiple batadv_ogm2_packet can be stored in an skbuff. The functions
batadv_v_ogm_send_to_if() uses batadv_v_ogm_aggr_packet() to check if there
is another additional batadv_ogm2_packet in the skb or not before they
continue processing the packet.
The length for such an OGM2 is BATADV_OGM2_HLEN +
batadv_ogm2_packet->tvlv_len. The check must first check that at least
BATADV_OGM2_HLEN bytes are available before it accesses tvlv_len (which is
part of the header. Otherwise it might try read outside of the currently
available skbuff to get the content of tvlv_len.
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Multiple batadv_ogm_packet can be stored in an skbuff. The functions
batadv_iv_ogm_send_to_if()/batadv_iv_ogm_receive() use
batadv_iv_ogm_aggr_packet() to check if there is another additional
batadv_ogm_packet in the skb or not before they continue processing the
packet.
The length for such an OGM is BATADV_OGM_HLEN +
batadv_ogm_packet->tvlv_len. The check must first check that at least
BATADV_OGM_HLEN bytes are available before it accesses tvlv_len (which is
part of the header. Otherwise it might try read outside of the currently
available skbuff to get the content of tvlv_len.
Fixes: ef26157747 ("batman-adv: tvlv - basic infrastructure")
Reported-by: syzbot+355cab184197dbbfa384@syzkaller.appspotmail.com
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
an assert and a NULL pointer dereference) plus a small series from Luis
fixing instances of vfree() under spinlock.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl1f2fITHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi83fB/0a+TnNY8Q2aEeB9Y/0sckSpRCsMGMV
syt2krwKC0EYM1f2dkJdgCjlSjMzMcHPseP3g5odRXgyPKJt5O9oE7l3vGDC4Oyt
chqhEh86UzG6Kcptx6tIzsAGYS9S4NzxR5sfXF6oRu8m1bwk1n5IhKxYjQDTvAMd
RxwvpdguNA9xvHeUvLMTpy2R3qE3uQ2dxierutW67GeyeCPkvyBmazzi72Q36hlL
y1w8DWaPBemBk5QEM9vmz5i2xQeLO4h4ejhP4LcXyVjJtfvAPl0JWOsHMK4uWRJf
6XjbGDaGYvID0hTQLlEw/k73976HmRxSbaXRtCZN+IG3yWGTL8ID6GqI
=kaFB
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.3-rc6' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Three important fixes tagged for stable (an indefinite hang, a crash
on an assert and a NULL pointer dereference) plus a small series from
Luis fixing instances of vfree() under spinlock"
* tag 'ceph-for-5.3-rc6' of git://github.com/ceph/ceph-client:
libceph: fix PG split vs OSD (re)connect race
ceph: don't try fill file_lock on unsuccessful GETFILELOCK reply
ceph: clear page dirty before invalidate page
ceph: fix buffer free while holding i_ceph_lock in fill_inode()
ceph: fix buffer free while holding i_ceph_lock in __ceph_build_xattrs_blob()
ceph: fix buffer free while holding i_ceph_lock in __ceph_setxattr()
libceph: allow ceph_buffer_put() to receive a NULL ceph_buffer
For control packets (i.e. LLDP packets) to be able to egress
from the main VSI, a bit has to be set in the TX_descriptor.
This should only be done for the main VSI and only if the
FW LLDP agent is disabled. A bit to allow this also has to
be set in the VSI context.
Add the logic to add the necessary bits in the VSI context
for the PF_VSI and the TX_descriptors for control packets
egressing the PF_VSI.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
