Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the TX
aggregation code to use the mutex the RX part
already uses. The spinlock is still necessary
around some code to avoid races with TX, but
now we can also synchronize_net() to avoid
getting an inconsistent sequence number.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we want the code to be able to sleep
in the future, it must not be called from
the timer directly. To achieve that, simply
call the function drivers would call, and
also use RCU in the timer to get the struct
so we don't need to rely on the spinlock in
the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the RX
aggregation code to use a mutex, so that it
would already allow drivers to sleep. But
explicitly disable BHs around the callback
for now since the TX part cannot yet sleep,
and drivers' locking might require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed that when there was _no_ traffic at
all on a given aggregation session, it would
never time out. This won't happen unless you
forced creating a session, but fix it anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we want the code to be able to sleep
in the future, it must not be called from
the timer directly. To prepare, move it out
into the aggregation work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the block-ack session works into common
code, since it will be needed for RX agg too
in the next patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver or rate control requests starting
or stopping an aggregation session, that currently
causes a direct callback into the driver, which
could potentially cause locking problems. Also,
the functions need to be callable from contexts
that cannot sleep, and thus will interfere with
making the ampdu_action callback sleeping.
To address these issues, add a new work item for
each station that will process any start or stop
requests out of line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently maintains the ampdu_lock to
avoid starting a queue due to one aggregation
session while another aggregation session needs
the queue stopped.
We can do better, however, and instead refcount
the queue stops for this particular purpose,
thus removing the need for the lock. This will
help making ampdu_action able to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we allocate some memory for each TX
aggregation session and additionally keep a
state bitmap indicating the state it is in.
By using RCU to protect the pointer, moving
the state into the structure and some locking
trickery we can avoid locking when the TX agg
session is fully operational.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we allocate some memory for each RX
aggregation session and additionally keep a
flag indicating whether or not it is valid.
By using RCU to protect the pointer and making
sure that the memory is fully set up before it
becomes visible to the RX path, we can remove
the need for the bool that indicates validity,
as well as for locking on the RX path since it
is always synchronised against itself, and we
can guarantee that all other modifications are
done when the structure is not visible to the
RX path.
The net result is that since we remove locking
requirements from the RX path, we can in the
future use any kind of lock for the setup and
teardown code paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the aggregation callback processing
to the per-sdata skb queue and a work function
rather than the tasklet.
Unfortunately, this means that it extends the
pkt_type hack to that skb queue. However, it
will enable making ampdu_action API changes
gradually, my current plan is to get rid of
this again by forcing drivers to only return
from ampdu_action() when everything is done,
thus removing the callbacks completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a corner case where we receive a fragmented
frame during a blockack session, in which case we
will terminate that session. To simplify future work
in this area that will culminate in allowing the
driver callbacks for aggregation to sleep, move the
processing of this case out of the RX path into the
interface work.
This will simplify future work because the new place
for this code doesn't require that the function will
always be atomic, which the RX path needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for making the ampdu_action callback
sleep, make mac80211 always process blockack
action frames from the skb queue. This gets rid
of the current special case for managed mode
interfaces as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code is duplicated between ibss, mesh and
managed mode regarding the queueing of management
frames. Since all modes now use a common skb
queue and a common work function, we can pull
the queueing code into the rx handler directly
and remove the duplicated length checks etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the management processing functions free the
skb after they are done, so this can be done in
the new common code instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even with the previous patch, IBSS, managed
and mesh modes all attach their own work
function to the shared work struct, which
means some duplicated code. Change that to
only have a frame processing function and a
further work function for each of them and
share some common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have their
own work struct, and in the future we want
to also use it in other modes to process
frames from the now common skb queue.
This also makes the skb queue and work safe
to use from other interface types.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have an
skb queue, and in the future we want to
also use it in other modes, so make them
all use a common skb queue already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places use RCU locking for accessing
the station list, even though they do not need
to. Use mutex locking instead to prepare for the
locking changes I want to make. The mlme code is
also using a WLAN_STA_DISASSOC flag that has the
same meaning as WLAN_STA_BLOCK_BA, so use that.
While doing so, combine places where we loop
over stations twice, and optimise away some of
the loops by checking if the hardware supports
aggregation at all first.
Also fix a more theoretical race condition: right
now we could resume, set up an aggregation session,
and right after tear it down again due to the code
that is needed for hardware reconfiguration here.
Also mark add a comment to that code marking it as
a workaround.
Finally, remove a pointless aggregation disabling
loop when an interface is stopped, directly after
that we remove all stations from it which will also
disable all aggregation sessions that may still be
active, and does so in a race-free way unlike the
current loop that doesn't block new sessions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When in IBSS mode, currently action frame TX and RX
cannot be used. Allow using it to talk to any peer,
or for public action frames. Also, while at it,
restructure the code in mac80211 to make it easier
to add this for other interface types in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes linux-2.6 warning:
drivers/net/wireless/libertas_tf/main.c: In function 'lbtf_rx':
drivers/net/wireless/libertas_tf/main.c:578: warning: 'stats.antenna' is used uninitialized in this function
drivers/net/wireless/libertas_tf/main.c:578: warning: 'stats.mactime' is used uninitialized in this function
stats struct needs to be set to 0 before use.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nobh option was only supported for writeback mode, but given that all
write paths actually create buffer heads it effectively was a no-op already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When we detect that not all antennas are
properly connected, we simply disable the
associated chains, but never notify the
user at all. Print out a warning so it is
obvious that happened and we know where
to start looking for related issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl4965_rx_mpdu_res_start is not 4695 specific, so rename it to more
general name iwl_rx_mpdu_res_start.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rename rxq->dma_addr to rxq->bd_dma to better emphasize that the
physical address stands for the receive buffer descriptor's address.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cancel scheduled run time calibration work when interface is going
down.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Test for null pointer prior to access.
Print "Not Allocated" if null pointer.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The length contained in the status word doesn't
include the status word's length itself, so we
need to account for that for tracing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The flow id (scd_flow) in a compressed BA packet should match the txq_id
of the queue from which the aggregated packets were sent. However, in
some hardware like the 1000 series, sometimes the flow id is 0 for the
txq_id (10 to 19). This can cause the annoying message:
[ 2213.306191] iwlagn 0000:01:00.0: Received BA when not expected
[ 2213.310178] iwlagn 0000:01:00.0: Read index for DMA queue txq id (0),
index 5, is out of range [0-256] 7 7.
And even worse, if agg->wait_for_ba is true when the bad BA is arriving,
this can cause system hang due to NULL pointer dereference because the
code is operating in a wrong tx queue!
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Pradeep Kulkarni <pradeepx.kulkarni@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We are seeing some race conditions between incoming station management
requests (station add/remove) and the internal unassoc RXON command that
modifies station table. Modify these flows to require the mutex to be held
and thus serializing them.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2207
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
No real bugs found, just removed some dead code.
Found by gcc 4.6's new warnings.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch changes the name of get_current function pointer to
get_battery_current to resolve a name conflict with the get_current
macro defined in current.h.
This conflict resulted in a build-failure[1] for the sh4 arch
allyesconfig:
drivers/power/ds2782_battery.c:216:48: error: macro "get_current"
passed 2 arguments, but takes just
This patch fixes the issue. To be consistent the other function pointers
(_voltage,_capacity) were renamed too.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The parameter (work) is unused, remove it.
Reported from Eric Dumazet.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Instead of doing one atomic operation per frag, we can factorize them.
Reported from Eric Dumazet.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
If the returned csum value is 0, We has set ip_summed with
CHECKSUM_UNNECESSARY flag in __skb_checksum_complete_head().
So this patch kills the check and changes to return to upper
caller directly.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
- must use atomic_inc_not_zero() in instance_lookup_get()
- must use hlist_add_head_rcu() instead of hlist_add_head()
- must use hlist_del_rcu() instead of hlist_del()
- Introduce NFULNL_COPY_DISABLED to stop lockless reader from using an
instance, before we do final instance_put() on it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This was a very hard to trigger race condition.
If we got a state packet from the peer, after drbd_nl_disk() has
already changed the disk state to D_NEGOTIATING but
after_state_ch() was not yet run by the worker, then receive_state()
might called drbd_sync_handshake(), which in turn crashed
when accessing p_uuid.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now that the FDPIC relocations have been given fixed numbers upstream,
switch to using those. The previous values only applied to experimental
toolchains that never made it in to the wild, so the impact remains
minimal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently kprobes support relies on several saved opcode variables for
saving and restoring state, without any specific locking. This is
inherently racy on SMP, and given that we already use per-CPU variables
for everything else, convert these over too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The line-in input is 0x7 not 0x2 for MacBook (Pro) 5,1 / 5,2 models
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
asm/ptrace.h is getting a bit messy, with the _32/_64-specific changes
being fairly insular. This splits out the header accordingly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>