Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one errors.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC drivers/char/tty_buffer.o
drivers/char/tty_buffer.c: In function ‘tty_insert_flip_string_fixed_flag’:
drivers/char/tty_buffer.c:251: warning: comparison of distinct pointer types lacks a cast
drivers/char/tty_buffer.c: In function ‘tty_insert_flip_string_flags’:
drivers/char/tty_buffer.c:288: warning: comparison of distinct pointer types lacks a cast
Fix it by replacing min() with min_t() in tty_insert_flip_string_flags and
tty_insert_flip_string_fixed_flag().
Signed-off-by: Fang Wenqi <antonf@turbolinux.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan pointed out a race in the code where hvc_remove is invoked. The
recent virtio_console work is the first user of hvc_remove().
Alan describes it thus:
The hvc_console assumes that a close and remove call can't occur at the
same time.
In addition tty_hangup(tty) is problematic as tty_hangup is asynchronous
itself....
So this can happen
hvc_close hvc_remove
hung up ? - no
lock
tty = hp->tty
unlock
lock
hp->tty = NULL
unlock
notify del
kref_put the hvc struct
close completes
tty is destroyed
tty_hangup dead tty
tty->ops will be NULL
NULL->...
This patch adds some tty krefs and also converts to using tty_vhangup().
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linuxppc-dev@ozlabs.org
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can get this driver enabled via MFD_TIMBERDALE which only
requires GPIO to be on.
But the of_address_to_resource() function is only present on
powerpc and microblaze, so we have to conditionalize the
CONFIG_OF probing bits on that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TTY layer takes some care to ensure that only sub-page allocations
are made with interrupts disabled. It does this by setting a goal of
"TTY_BUFFER_PAGE" to allocate. Unfortunately, while TTY_BUFFER_PAGE takes the
size of tty_buffer into account, it fails to account that tty_buffer_find()
rounds the buffer size out to the next 256 byte boundary before adding on
the size of the tty_buffer.
This patch adjusts the TTY_BUFFER_PAGE calculation to take into account the
size of the tty_buffer and the padding. Once applied, tty_buffer_alloc()
should not require high-order allocations.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit eec9fe7d1a.
Ari writes as the reason this should be reverted:
The problems with this patch include:
1. There's at least one subtlety I overlooked - switching
between X servers (i.e. from one X VT to another) still requires
the cooperation of both X servers. I was assuming that KMS
eliminated this.
2. It hasn't been tested at all (no X server patch exists which
uses the new mode).
As he was the original author of the patch, I'll revert it.
Cc: Ari Entlich <atrigent@ccs.neu.edu>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
node_read_distance() has a BUILD_BUG_ON() to prevent buffer overruns when
the number of nodes printed will exceed the buffer length.
Each node only needs four chars: three for distance (maximum distance is
255) and one for a seperating space or a trailing newline.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A number of functions in the driver core return ERR_PTR() values on
error. Document this in the kernel-doc of the functions.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes these warnings:
drivers/base/cpu.c:264: warning: initialization from incompatible pointer type
drivers/base/cpu.c:265: warning: initialization from incompatible pointer type
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace uio_mem example for kobjects with uio_map, since the uio_mem
struct no longer contains a kobject.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix kernel-doc warning in firmware_class.c:
Warning(drivers/base/firmware_class.c:94): No description found for parameter 'attr'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the kernel-doc notation for early
platform functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a sysfs lockdep warning in the mlx4 code.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a sysfs lockdep warning in the infiniband code.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a sysfs lockdep warning in the ipmi code.
Thanks to Eric Biederman and Yinghai Lu for the original versions of the
patch, unfortunatly they did not submit them in a form they could be
applied in.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PPC64 is failing to boot the latest mmotm due to an uninitialised pointer in
pci_create_legacy_files(). The surprise is that machines boot at all and it
would appear to affect current mainline as well. This patch fixes the problem.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Note that since all the microphones share a bias there is a single
jack exported for all three, even though there are two physical
connectors plus the soldered down silicon mic. Note also that the SiMic
is always present by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The export is not needed since the per-bus code lives in the same
module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Yi Li <yi.li@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initial version of TWL6040 codec driver.
The TWL6040 codec uses a proprietary PDM-based digital audio interface.
Audio paths supported are:
- Input: Main Mic, Sub Mic, Headset Mic, Auxiliary-FM Left/Right
- Output: Headset Left/Right, Handsfree Left/Right
TWL6040 codec supports power-up/down manual and automatic sequence.
Manual sequence is done through a specific register writes sequence.
Automatic sequence is done when the codec is powered-up through the
external AUDPWRON line. The completion of the sequence is signaled
through the audio interrupt.
TWL6040 codec sysclk can be provided by: low-power or high
performance PLL:
- The low-power PLL takes a low-frequency input at 32,768 Hz and
generates an approximate of 17.64 or 19.2 MHz (for 44.1 KHz and 48 KHz
respectively)
- The high-performance PLL generates an exact 19.2 MHz clock signal
from high-frequency input at 12/19.2/26/38.4 MHz.
Low-power playback mode is a special scenario where only headset path
(headset DAC and driver) is active.
For the particular case of headset path, PLL being used defines the
headset power mode: low-power, high-performance.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're keeping track of the number of times we've iterated but never
actually using this to bail out if the chip looks stuck.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
During validation of the internal clocking setup it has
been found that the following settings were not configured
in an optimal way:
ASRC_CTRL_A: SRCLKDIV was incorrect, instad of divide ratio 3,
ratio of 2 has to be used (as the comment stated)
DAC_CTRL_A: Fs = Fsref is the desired configuration instead of
Fs = Fsref / 1.5
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To make DSP_A mode working correctly the data delay should be
configured to 0. DSP_B mode thus can not be used with DAC33,
so remove it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Basic support for Left Justified coding for OMAP McBSP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Indentation in initial support for McPDM driver was converted to spaces.
Use tabs to comply with open source coding-style.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added alc_codec_rename() helper for renaming codec->chip_name.
Added Acer-specific codec naming for ALC269/662.
[Clean-up and refactoring by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added alc_auto_parse_customize_define() to parse the Realtek-specific
attributes from SKU. Also enable beep controls only when the proper
attribute bit is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This area contains the Nand Flash controller registers. There
is no need to map them statically as the Nand driver uses ioremap().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Freescale redboot passes the silicon revision via
ATAG_REVISION. Remove this bootloader dependency by
doing the same as redboot does in the Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add new check for MIC. Do the internal DMIC as the Front MIC.
It could solve the default record source index issue.
[Fix the check properly using the bitmask by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This looks cleaner and allows us to call mx51_revision
later when we can use ioremap to determine the silicon
revision dynamically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I think this should be automatic pin instead of ping.
(but could be wrong).
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Index 0-6 in p4_templates are reserved for common hardware
events. So p4_templates is arranged as below:
0 - 6: common hardware events
7 - N: cache events
N+1 - ...: other raw events
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <1268983738.13901.142.camel@minggr.sh.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove alignment padding to shrink struct request from 336 to 320 bytes
so needing one fewer cacheline and therefore removing 48 bytes from
struct request_queue.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Extend the INTC code with ioremap() support V2.
Support INTC controllers that are not accessible through
a 1:1 virt:phys window. Needed by SH-Mobile ARM INTCS.
The INTC code behaves as usual if the io window resource
is omitted. The slow phys->virt lookup only happens during
setup. The fast path code operates on virtual addresses.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the INTC code to warn and return an error code
in the case of memory allocation failure.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Alex Shi reported a kbuild regression which is about 10% performance lost.
He bisected to this commit: 3dde36ddea.
The reason is cfqq_close() can't find close cooperator. Restoring
cfq_rq_close()'s threshold to original value makes the regression go away.
Since for_preempt parameter isn't used anymore, this patch deletes it.
Reported-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The description says:
Cause IO segments sent to a device for DMA to be merged virtually
by the IOMMU when they happen to have been allocated contiguously.
This doesn't add pressure to the IOMMU allocator. However, some
drivers don't support getting large merged segments coming back
from *_map_sg().
Most drivers don't have this problem; it is safe to say Y here.
It's out of date. Long ago, drivers didn't have a way to tell IOMMUs
about their segment length limit (that is, the maximum segment length
that they can handle). So IOMMUs merged as many segments as possible
and gave too large segments to drivers.
dma_get_max_seg_size() was introduced to solve the above
problem. Device drives can use the API to tell IOMMU about the maximum
segment length that they can handle. In addition, the default limit
(64K) should be safe for everyone.
So this config option seems to be unnecessary.
Note that this config option just enables users to disable the virtual
merging by default. Users can still disable the virtual merging by the
boot parameter.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc initializes swiotlb before parsing the kernel boot options so
swiotlb options (e.g. specifying the swiotlb buffer size) are ignored.
Any time before freeing bootmem works for swiotlb so this patch moves
powerpc's swiotlb initialization after parsing the kernel boot
options, mem_init (as x86 does).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When printk() is disabled (CONFIG_PRINTK) at menu item
General setup
-> Configure standard kernel features (for small systems)
-> Enable support for printk
then there should be no printk() calls at all.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc implementations of syscall_get_error and
syscall_set_return_value should use CCR0:S0 (0x10000000) for testing
and setting syscall error status. Fortunately these APIs don't seem
to be used at the moment.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>