The MAX9877 needs an address of start register when we write values to
registers through i2c_master_send(), but the code for this was missed in
max9877_write_regs().
If the value of control is 0 in the max9877_set_out_mode(), the value is
not increased to 1, but actually the value to write to the register
should be 1.
And the register bits for out_mode and osc_mode should be cleared before
writing.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Conexant CX20442-11 voice modem codec, suitable
for use by the ASoC board driver for Amstrad E3 (Delta) videophone. Related
sound card driver will follow.
This codec is an optional part of the Conexant SmartV three chip modem design.
As such, documentation for its proprietary digital audio interface is not
available. However, on Amstrad Delta board, thanks to Mark Underwood who
created an initial, omap-alsa based sound driver a few years ago[1], the codec
has been discovered to be accessible not only from the modem side, but also
over the OMAP McBSP based CPU DAI. Thus, the driver can be used by any sound
card that can access the codec DAI directly. The DAI configuration parameters
(sample rate and format, number of channels) has been selected out empirically
for best user experience.
The codec analogue interface consists of two pairs of analogue I/O pins:
speakerphone interface or telephone handset/headset interface. Furthermore, it
seams to provide two operation modes for speakerphone I/O: standard and
advanced, with automatic gain control and echo cancelation. Even if the codec
control interface is unknown and not available, all those interfaces and modes
can be selected over the modem chip using V.253 commands. The driver is able
to issue necessary commands over a suitable hw_write function if provided by a
sound card driver. Otherwise, the codec can be controlled over the modem from
userspace while inactive.
Even if nothig is known about the codec internal power management
capabilities, DAPM widgets has been used to model the codec audio map.
Automatically performed powering up/down of those virtual widgets results in
corresponding V.253 commands being issued.
Some driver features/oddities may be board specific, but I have no way to
verify that with any board other than Amstrad Delta.
[1] http://www.earth.li/pipermail/e3-hacking/2006-April/000481.html
Created and tested against linux-2.6.31-rc3.
Applies and works with linux-omap-2.6 commit
7c5cb7862d32cb344be7831d466535d5255e35ac as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a defconfig and a mach-types entry for
the kfr2r09 board.
At this point only a few devices like SCIF, KEYSC and
NOR Flash are supported together with sh7724 devices
such as IIC0, IIC1 and the multimedia blocks exported
via UIO.
Kexec is supported, but booting from flash is not (yet).
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify atmel LCD driver: atmel_lcdfb for at91sam9g10. This add a clock
management equivalent to at91sam9261.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here are the new sound enabling patches for IbexPeak.
Summary of tested features:
- playback
- Front Headphone: OK
- 8 channel audio: Front/Rear/CLFE/Side all OK
- recording
- Front Mic/Rear Mic: both OK
(front/rear/line mics are selectable in the "Input source" alsamixer control)
- Line In: not working
(in 6ch mode, its amp/mute, direction and route all looks fine,
so I'm a little puzzled)
(hopefully no one will care this feature)
- digital SPDIF input/output: not tested (no equipment)
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add spi resource define for w90p910 spi driver.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When programming clock api, I named this spi device
as w90p910-usi, now, I think named it as w90p910-spi better
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add mac resource define for w90p910 mac driver.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add fmi resource define for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the NOR flash support for TS-7200.
The TS-7200 models all have 16-bit NOR flash. Update the platform
init to support this.
Remove the private TS72XX_NOR_* defines and use the common ep93xx
defines for the external chip select physical base address instead.
Move the NOR flash registration into a static __init function. When
the NAND flash support is updated this function will also be used
to register the NAND flash for the TS-7250 and TS-7260.
Tested-by: Matthieu Crapet <mcrapet@gmail.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added the logging functionality to xrun_debug to record the hwptr
updates via snd_pcm_update_hw_ptr() and snd_pcm_update_hwptr_interrupt(),
corresponding to 16 and 8, respectively.
For example,
# echo 9 > /proc/asound/card0/pcm0p/xrun_debug
will record the position and other parameters at each period interrupt
together with the normal XRUN debugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PLL was not being enabled when it was not bypassed. This patch
enables the PLL when it is used. Additionally, it disables the PLL
when it is bypassed.
Without this patch, the audio on TI DM646x EVM and DM355 EVM
does not work properly. The bit clocks and the frame sync signals
from the codec are not correct and hence the playback/record are faster
than usual for most sample rates. The reason for this was that the PLL
was not enabled when it was not bypassed.
Tested on DM6467 EVM, playback tested on DM355 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.
Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.
This work is intensively based on dw_dmac and several slave implementations.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
clk_disable() in remove method is not needed since we already
have clk_disable in pxa27x_keypad_close().
Also make sure the driver uses resource_size() and helpers from
include/input/matrix_keypad.h
Tested-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It seems that thread_count is not properly calculated in dmatest.
In fact the thread count number that is returned from dmatest_add_threads() is
not correctly added to the thread_count and thus not properly printed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmatest usually waits for the killing of its kthreads to stop
running tests. This patch adds a parameter that sets a maximum
number of test iterations.
This feature is quite interesting for debugging when you set a lot of
traces in your dmaengine controller driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds KEYSC keypad support to the kfr2r09 board.
The keys driven by the sh7724 on-chip KEYSC block are
described as a platform device and platform data for
the sh_keysc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds NOR flash support to the kfr2r09 board.
NOR flash support is added by describing the NOR flash
chip hooked up to CS0 as platform device data for the
physmap-flash MTD driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic kfr2r09 board support. Only
the SCIF1 console is supported with this patch, but
this patch and a proper sh7724 configuration is all
that is needed. Combine with an initramfs to have a
small RAM based kernel and distribution booted as
zImage from RAM via JTAG.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().
This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().
The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.
This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.
The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move r8a66597 hardware register definitions from the host
controller header file to the platform data header file.
With this change in place we can easily share register
definitions between the host controller driver and a future
gadget driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_APM_EMULATION=n em-x270 build fails with linker error:
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_critical': em-x270.c:(.text+0x12c0): undefined reference to `apm_queue_event'
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_low': em-x270.c:(.text+0x12c8): undefined reference to `apm_queue_event'
make: *** [.tmp_vmlinux1] Error 1
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
According to investigations from windows team ,hw team,
and our test results on all 4x platofrms available
(gm45, g45b, q45, g45a, g45c, g41a, and g41), we find
currently Hot plug live status and Hot plug interrupt
detection are not reliable, sometime the results from
the two approaches are contradicts. So we chose edid
detection for hdmi output.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix UP compile failure caused by irq_thread_check_affinity
* 'lockdep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep:
lockdep: Fix lockdep annotation for pipe_double_lock()
list_entry, which is an alias for container_of, cannot return NULL, as
there is no way to add a NULL value to a doubly linked list.
A simplified version of the semantic match that findds this problem is as
follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r@
expression x,E;
statement S1,S2;
position p,p1;
@@
*x = list_entry@p(...)
... when != x = E
*if@p1 (x == NULL) S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add explicit key mappings for TwinHan USB HID remote control.
All dummy Ctrl, Alt, Meta, ... key press/release events generated
by the remote are silenced by "unmapping" them. This makes Power and
Volume keys single-key and strips the regular (even while idle) key
release events for Ctrl, Alt, Meta, ...
Signed-off-by: Bruno Premont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions of several HID drivers from drivers/hid/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch enables rumble in Thrustmaster Dual 3-in-1 trigger gamepads (in both
PC and PS3 modes). It uses the same code as Thrustmaster FireStorm Dual Power 2,
so it only adds new USB IDs to hid-core.c and hid-tmff.c
Signed-off-by: Ruben Aos Garralda <rubenatch@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When both touch and pen are active send a tool announcement before
sending any status changes so that event users may differentiate
which tool is changing.
Restored three usage codes used by the pen.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Acked-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add force feedback support for Logitech WingMan Formula Force GP
(0x046d/0xc293).
Reported-by: wylda@volny.cz
Tested-by: wylda@volny.cz
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch extends the existing Samsung IrDA (0419:0001) quirk file with newly
reported variants:
* New device variants with 203 byte and 135 byte report descriptors were
reported to be recognized incorrectly. This patch adds an autodetection for
those two, using report descriptor size to enable new quirks.
* Any other unknown 0419:0001 variants will now be treated without any quirk
flags (i.e. IGNORE_HIDINPUT/HIDDEV_FORCE will not be set by default anymore).
More details:
1. Descriptor size 184 bytes ("Satelco bundled remote")
Already supported since kernel 2.6.25 (my old patch).
2. Descriptor size 203 bytes ("Optronix remote")
This receiver mostly works with the regular HID input driver. Only when some
keys are released, another spurious key press event is interpreted due to
incorrect array ranges. According to HID 1.11, section 6.2.2.5, arrays should
return a 0 value when no control is asserted, and ranges should go from 1 to
the number of elements. The patch clips the value with a logical range from
1..15 (instead of originally 0..18).
Ticket with more information available at
https://bugs.launchpad.net/bugs/326986
3. Descriptor size 135 bytes ("Gotview remote")
This receiver has a similar issue than the previous one, i.e. it mostly works
with regular HID input, except some key press events get stuck on key release.
The patch clips the array value from 1..14 (instead of originally 0..17).
Ticket with more information available at
http://bugs.archlinux.org/task/15216
4. Other unknown variants (found one report with 218 bytes,
but no further information about issues)
For such unknown variants we should refrain from changing any device flags.
Currently, HIDINPUT is suppressed and HIDDEV is enforced (because in 2.6.25 the
quirk table did not yet allow differentiating variants and we
did not expect variants either). Now we should be as strict as
possible and enable it only for the first variant above.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since genirq: Delegate irq affinity setting to the irq thread
(591d2fb02e) compilation with
CONFIG_SMP=n fails with following error:
/usr/src/linux-2.6/kernel/irq/manage.c:
In function 'irq_thread_check_affinity':
/usr/src/linux-2.6/kernel/irq/manage.c:475:
error: 'struct irq_desc' has no member named 'affinity'
make[4]: *** [kernel/irq/manage.o] Error 1
That commit adds a new function irq_thread_check_affinity() which
uses struct irq_desc.affinity which is only available for CONFIG_SMP=y.
Move that function under #ifdef CONFIG_SMP.
[ tglx@brownpaperbag: compile and boot tested on UP and SMP ]
Signed-off-by: Bruno Premont <bonbons@linux-vserver.org>
LKML-Reference: <20090722222232.2eb3e1c4@neptune.home>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This off-by-one bug causes sendfile() to not work properly. When a task
calls sendfile() on a file on a CIFS filesystem, the syscall returns -1
and sets errno to EOVERFLOW.
do_sendfile uses s_maxbytes to verify the returned offset of the file.
The problem there is that this value is cast to a signed value (loff_t).
When this is done on the s_maxbytes value that cifs uses, it becomes
negative and the comparisons against it fail.
Even though s_maxbytes is an unsigned value, it seems that it's not OK
to set it in such a way that it'll end up negative when it's cast to a
signed value. These casts happen in other codepaths besides sendfile
too, but the VFS is a little hard to follow in this area and I can't
be sure if there are other bugs that this will fix.
It's not clear to me why s_maxbytes isn't just declared as loff_t in the
first place, but either way we still need to fix these values to make
sendfile work properly. This is also an opportunity to replace the magic
bit-shift values here with the standard #defines for this.
This fixes the reproducer program I have that does a sendfile and
will probably also fix the situation where apache is serving from a
CIFS share.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
A recent regression when dealing with older servers. This bug was
introduced when we made serverino the default...
When the server can't provide inode numbers, disable it for the mount.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>