Commit graph

932,869 commits

Author SHA1 Message Date
Kalle Valo
56343a3cfd wl12xx: allocate buffer spi read/write command buffer kzalloc()
Needed for DMA safe transfers.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:42 -04:00
Kalle Valo
8d47cdb617 wl12xx: reserve buffer for partition command in struct wl12xx
This is now DMA safe.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:42 -04:00
Kalle Valo
c4f5c85218 wl12xx: fix error handling in wl12xx_probe()
Resources were not freed properly in some cases.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:42 -04:00
Kalle Valo
1d3b813061 wl12xx: reserver buffer for read32()/write32() in struct wl12xx
The buffer is needed for DMA safe transfers.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:42 -04:00
Kalle Valo
ff25839bf0 wl12xx: cmd and acx interface rework
Rework cmd and acx interfaces, it was just too confusing earlier. Now
all commands need to contain all the needed headers, either just cmd
headers or both cmd and acx headers. This accomplish to remove the
extra copy done for each command. The interfaces are now properly
documented as well.

Also try to make all commands safe for DMA transfers. I might have missed
some, but most of them should be fixed now.

And this is not all! As a free bonus you will also get some cosmetic
cleanups and code reorganisation. Order today!

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:41 -04:00
Vasanthakumar Thiagarajan
c4f9f16b30 ath9k: Make sure we configure a non-zero beacon interval
This patch moves the sanity check on beacon interval
which was done only for mesh mode to all operating
modes just to be safe.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:41 -04:00
Andrey Yurovsky
e0d6133cba libertas: remove ps_supported flag, use fwcapinfo
Power save support depends on the firmware capabilities rather than the
card's hardware interface.  Use the FW_CAPINFO_PS bit in the firmware
capabilities mask throughout the driver in place of the redundant
ps_supported flag and don't make decisions about PS support in the
interface drivers (with the exception of a special case in the USB
driver).

V2: put the USB special case in the right place.

Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:41 -04:00
Bob Copeland
f0f3d388ba ath5k: enable hardware LEDs
Cardbus and some PCI cards use hardware LEDs rather than software GPIOs.
Program them with the proper blink patterns when idle, scanning or
associated.  Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13288.

Tested-by: Frans Pop <elendil@planet.nl>
Tested-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:41 -04:00
Bob Copeland
46026e8f48 ath5k: cleanup ath5k_hw struct
ah_gpios array isn't used, and ah_current_channel can be a pointer
instead of an embedded struct.  Removing these and some other
write-only variables, and moving some things around for better
packing and cache utilization saves 116 bytes.

   text	   data	    bss	    dec	    hex	filename
 121762	    472	     64	 122298	  1ddba	ath5k_before.ko
 121646	    472	     64	 122182	  1dd46	ath5k.ko

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:41 -04:00
Vasanthakumar Thiagarajan
8a46097a6c ath9k: downgrade ASSERT() in ath_clone_txbuf()
We can easily run out of tx buf if there is any stuck in
transmission, so downgrade it to WARN_ON().

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:39 -04:00
Vasanthakumar Thiagarajan
c3d8f02ed9 ath9k: Remove unnecessary count for addba attempt
mac80211 already has one to keep track of number of failure
addba attempts.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:39 -04:00
Vasanthakumar Thiagarajan
089e698d23 ath9k: Nuke unneccesary helper function to see if aggr is active
IEEE80211_TX_CTL_AMPDU in tx control flags should be enough
to confirm BA is negotiated for that tid.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:38 -04:00
Johannes Berg
e36d56b648 cfg80211: pass netdev to change_virtual_intf
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-10 14:57:38 -04:00
Linus Torvalds
2a6f86bc5e Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing: Fix trace_print_seq()
  kprobes: No need to unlock kprobe_insn_mutex
  tracing/fastboot: Document the need of initcall_debug
  trace_export: Repair missed fields
  tracing: Fix stack tracer sysctl handling
2009-07-10 11:41:41 -07:00
Vivek Goyal
32f2e807a3 cfq-iosched: reset oom_cfqq in cfq_set_request()
In case memory is scarce, we now default to oom_cfqq. Once memory is
available again, we should allocate a new cfqq and stop using oom_cfqq for
a particular io context.

Once a new request comes in, check if we are using oom_cfqq, and if yes,
try to allocate a new cfqq.

Tested the patch by forcing the use of oom_cfqq and upon next request thread
realized that it was using oom_cfqq and it allocated a new cfqq.

Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-07-10 20:31:54 +02:00
FUJITA Tomonori
ecb554a846 block: fix sg SG_DXFER_TO_FROM_DEV regression
I overlooked SG_DXFER_TO_FROM_DEV support when I converted sg to use
the block layer mapping API (2.6.28).

Douglas Gilbert explained SG_DXFER_TO_FROM_DEV:

http://www.spinics.net/lists/linux-scsi/msg37135.html

=
The semantics of SG_DXFER_TO_FROM_DEV were:
   - copy user space buffer to kernel (LLD) buffer
   - do SCSI command which is assumed to be of the DATA_IN
     (data from device) variety. This would overwrite
     some or all of the kernel buffer
   - copy kernel (LLD) buffer back to the user space.

The idea was to detect short reads by filling the original
user space buffer with some marker bytes ("0xec" it would
seem in this report). The "resid" value is a better way
of detecting short reads but that was only added this century
and requires co-operation from the LLD.
=

This patch changes the block layer mapping API to support this
semantics. This simply adds another field to struct rq_map_data and
enables __bio_copy_iov() to copy data from user space even with READ
requests.

It's better to add the flags field and kills null_mapped and the new
from_user fields in struct rq_map_data but that approach makes it
difficult to send this patch to stable trees because st and osst
drivers use struct rq_map_data (they were converted to use the block
layer in 2.6.29 and 2.6.30). Well, I should clean up the block layer
mapping API.

zhou sf reported this regiression and tested this patch:

http://www.spinics.net/lists/linux-scsi/msg37128.html
http://www.spinics.net/lists/linux-scsi/msg37168.html

Reported-by: zhou sf <sxzzsf@gmail.com>
Tested-by: zhou sf <sxzzsf@gmail.com>
Cc: stable@kernel.org
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-07-10 20:31:53 +02:00
FUJITA Tomonori
76da03467a block: call blk_scsi_ioctl_init()
Currently, blk_scsi_ioctl_init() is not called since it lacks
an initcall marking. This causes the command table to be
unitialized, hence somce commands are block when they should
not have been.

This fixes a regression introduced by commit
018e044689

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-07-10 20:31:53 +02:00
Jens Axboe
8aa7e847d8 Fix congestion_wait() sync/async vs read/write confusion
Commit 1faa16d228 accidentally broke
the bdi congestion wait queue logic, causing us to wait on congestion
for WRITE (== 1) when we really wanted BLK_RW_ASYNC (== 0) instead.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-07-10 20:31:53 +02:00
Heiko Carstens
f9f868dbcc timer stats: fix quick check optimization
git commit 507e1231 "timer stats: Optimize by adding quick check to
avoid function calls" added one wrong check so that one unnecessary
function call isn't elimated.

time_stats_account_hrtimer() checks if timer->start_pid isn't
initialized in order to find out if timer_stats_update_stats() should
be called.  However start_pid is initialized with -1 instead of 0, so
that the function call always happens.

Check timer->start_site like in timer_stats_account_timer() to fix
this.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2009-07-10 19:33:00 +02:00
Thomas Gleixner
6ff7041dbf hrtimer: Fix migration expiry check
The timer migration expiry check should prevent the migration of a
timer to another CPU when the timer expires before the next event is
scheduled on the other CPU. Migrating the timer might delay it because
we can not reprogram the clock event device on the other CPU. But the
code implementing that check has two flaws:

- for !HIGHRES the check compares the expiry value with the clock
  events device expiry value which is wrong for CLOCK_REALTIME based
  timers.

- the check is racy. It holds the hrtimer base lock of the target CPU,
  but the clock event device expiry value can be modified
  nevertheless, e.g. by an timer interrupt firing.

The !HIGHRES case is easy to fix as we can enqueue the timer on the
cpu which was selected by the load balancer. It runs the idle
balancing code once per jiffy anyway. So the maximum delay for the
timer is the same as when we keep the tick on the current cpu going.

In the HIGHRES case we can get the next expiry value from the hrtimer
cpu_base of the target CPU and serialize the update with the cpu_base
lock. This moves the lock section in hrtimer_interrupt() so we can set
next_event to KTIME_MAX while we are handling the expired timers and
set it to the next expiry value after we handled the timers under the
base lock. While the expired timers are processed timer migration is
blocked because the expiry time of the timer is always <= KTIME_MAX.

Also remove the now useless clockevents_get_next_event() function.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2009-07-10 17:32:55 +02:00
Steve French
65bc98b005 [CIFS] Distinguish posix opens and mkdirs from legacy mkdirs in stats
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
2009-07-10 15:27:25 +00:00
Thomas Gleixner
7e0c5086c1 hrtimer: migration: do not check expiry time on current CPU
The timer migration code needs to check whether the expiry time of the
timer is before the programmed clock event expiry time when the timer
is enqueued on another CPU because we can not reprogram the timer
device on the other CPU. The current logic checks the expiry time even
if we enqueue on the current CPU when nohz_get_load_balancer() returns
current CPU. This might lead to an endless loop in the expiry check
code when the expiry time of the timer is before the current
programmed next event.

Check whether nohz_get_load_balancer() returns current CPU and skip
the expiry check if this is the case.

The bug was triggered from the networking code. The patch fixes the
regression http://bugzilla.kernel.org/show_bug.cgi?id=13738
(Soft-Lockup/Race in networking in 2.6.31-rc1+195)

Cc: Arun Bharadwaj <arun@linux.vnet.ibm.com
Tested-by: Joao Correia <joaomiguelcorreia@gmail.com>
Tested-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2009-07-10 17:22:20 +02:00
Frans Pop
1aaad49e85 printk: Restore previous console_loglevel when re-enabling logging
When logging to console is disabled from userspace using klogctl()
and later re-enabled, console_loglevel gets set to the default
log level instead to the previous value.

This means that if the kernel was booted with 'quiet', the boot is
suddenly no longer quiet after logging to console gets re-enabled.

Save the current console_loglevel when logging is disabled and
restore to that value. If the log level is set to a specific value
while disabled, this is interpreted as an implicit re-enabling of
the logging.

The problem that prompted this patch is described in:

    http://lkml.org/lkml/2009/6/28/234

There are two variations possible on the patch below:

 1) If klogctl(7) is called while logging is not disabled, then set level
    to default (partially preserving current functionality):
  	case 7:		/* Enable logging to console */
 -		console_loglevel = default_console_loglevel;
 +		if (saved_console_loglevel == -1)
 +			console_loglevel = default_console_loglevel;
 +		else {
 +			console_loglevel = saved_console_loglevel;
 +			saved_console_loglevel = -1;
 +		}

 2) If klogctl(8) is called while logging is disabled, then don't enable
    logging, but remember the requested value for when logging does get
    enabled again:
  	case 8:		/* Set level of messages printed to console */
 [...]
 - 		console_loglevel = len;
 +		if (saved_console_loglevel == -1)
 +			console_loglevel = len;
 +		else
 +			saved_console_loglevel = len;

Yet another option would be to ignore the request.

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: cryptsetup@packages.debian.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <200907061331.49930.elendil@planet.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 16:02:23 +02:00
Cyrill Gorcunov
a1b4f1a5b7 x86, ipi: Clean up safe_smp_processor_id() by using the cpu_has_apic() macro helper
We already use a lot of cpu_has_ helpers.
Lets do here the same for consistency.

Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090705160154.GB4791@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 15:58:34 +02:00
Cyrill Gorcunov
9ff8094299 x86: Clean up idt_descr and idt_tableby using NR_VECTORS instead of hardcoded number
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090708180353.GH5301@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 13:57:13 +02:00
Ingo Molnar
e202687927 Merge branch 'tip/tracing/ring-buffer-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into tracing/core 2009-07-10 13:30:06 +02:00
Takashi Iwai
3c6aae4489 ALSA: hda - Check codec errors in snd_hda_get_connections()
The codec read errors in snd_hda_get_connections() are ignored so far,
and it causes a problem like the bug in the commit
    9d30937acc
    ALSA: hda_intel: more strict alc880_parse_auto_config dig_nid checking

Better to check errors in the function and returns a proper error code
rather than passing bogus NID values.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-07-10 12:56:41 +02:00
Jaroslav Kysela
9d30937acc ALSA: hda_intel: more strict alc880_parse_auto_config dig_nid checking
On some IbexPeak systems with ALC889A errors like "azx_get_response
timeout, switching to polling mode: last cmd=0xaf9f000b" are produced,
because non-existent codec #10 is wrongly accessed.

The problem is that snd_hda_get_connections() returns out-of-range result
for NID 0x1c (something like 0xf8f9 or 0xffff).

This patch adds a check to alc880_parse_auto_config() to avoid using
of this out-of-range NIDs. A better fix maybe to improve
snd_hda_get_connections() routine to check for valid NID ranges if
NIDs are expected as result.

Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-07-10 12:55:49 +02:00
Maynard Johnson
2b8777ca0c oprofile: reset bt_lost_no_mapping with other stats
The bt_lost_no_mapping is not getting reset at the start of a
profiling run, thus the oprofiled.log shows erroneous values for this
statistic. The attached patch fixes this problem.

Signed-off-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 12:35:36 +02:00
Takashi Iwai
31909b83ea ALSA: hda - Fix the merge error
Fix the merge error at the commit 305355aad8,
an addition of the missing alc880_gpio3_init_verbs to ALC882_TARGA model.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-07-10 12:33:48 +02:00
Robin Getz
8259cf4342 printk: Ensure that "console enabled" messages are printed on the console
Today, when a console is registered without CON_PRINTBUFFER,
end users never see the announcement of it being added, and
never know if they missed something, if the console is really
at the start or not, and just leads to general confusion.

This re-orders existing code, to make sure the console is
added, before the "console [%s%d] enabled" is printed out -
ensuring that this message is _always_ seen.

This has the desired/intended side effect of making sure that
"console enabled:" messages are printed on the bootconsole, and
the real console. This does cause the same line is printed
twice if the bootconsole and real console are the same device,
but if they are on different devices, the message is printed to
both consoles.

Signed-off-by : Robin Getz <rgetz@blackfin.uclinux.org>
Cc: "Andrew Morton" <akpm@linux-foundation.org>
Cc: "Linus Torvalds" <torvalds@linux-foundation.org>
LKML-Reference: <200907091308.37370.rgetz@blackfin.uclinux.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 12:24:47 +02:00
Lai Jiangshan
a35780005e tracing/workqueues: Add refcnt to struct cpu_workqueue_stats
The stat entries can be freed when the stat file is being read.
The worse is, the ptr can be freed immediately after it's returned
from workqueue_stat_start/next().

Add a refcnt to struct cpu_workqueue_stats to avoid use-after-free.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A51B16F.6010608@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 12:14:07 +02:00
Lai Jiangshan
d8ea37d5de tracing/stat: Add stat_release() callback
Add stat_release() callback to struct tracer_stat, so a stat tracer
can release it's entries after the stat file has been read out.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A51B16A.6020708@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 12:14:05 +02:00
Li Zefan
80098c200e kmemtrace: Rename some functions
So we have:

 - kmemtrace_print_alloc/free() for kmemtrace default output

 - kmemtrace_print_alloc/free_user() for binary output used
   by kmemtrace-user.

Suggested-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A51B288.70505@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 12:09:04 +02:00
Frederic Weisbecker
6a167c6558 tracing/kmemtrace: Use the %pf format
Remove the obsolete seq_print_ip_sym() usage and replace it
by the %pf format in order to print function symbols.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
LKML-Reference: <1247107590-6428-3-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 12:07:20 +02:00
Frederic Weisbecker
68baafcfc4 tracing/function-graph-tracer: Use the %pf format
Remove the obsolete seq_print_ip_sym() usage and replace it
by the %pf format in order to print function symbols.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <1247107590-6428-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 12:07:19 +02:00
Li Zefan
9d7e934408 ksym_tracer: Fix the output of stat tracing
- make ksym_tracer_stat_start() return head->first instead of
  &head->first
- make the output properly aligned

Before:

   Access type                Symbol                     Counter
     NA                   <NA>                              0
     RW                   pid_max                               0

After:

  Access Type   Symbol                                       Counter
  -----------   ------                                       -------
  RW            pid_max                                            0

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A52E346.5050608@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:59:44 +02:00
Li Zefan
558df6c8f7 ksym_tracer: Fix memory leak
- When remove a filter, we leak entry->ksym_hbp->info.name.

- With CONFIG_FTRAC_SELFTEST enabled, we leak ->info.name:
    # echo ksym_tracer > current_tracer
    # echo 'ksym_selftest_dummy:rw-' > ksym_trace_filter
    # echo nop > current_tracer

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A52E328.8010200@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:59:43 +02:00
Li Zefan
0d109c8f70 ksym_tracer: Report error when failed to re-register hbp
When access type is changed, the hw break point will be
unregistered and then be registered again with new access
type. But the registration may fail, in this case, -errno
should be returned.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A52E314.7070004@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:59:43 +02:00
Li Zefan
011ed56853 ksym_tracer: NIL-terminate user input filter
Make sure the user input string is NULL-terminated.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A52E300.7020601@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:59:42 +02:00
Li Zefan
92cf9f8f7e ksym_tracer: Fix validation of length of access type
Don't take newline into account, otherwise:

 # echo 'pid_max:-w-' > ksym_trace_filter
 # echo -n 'pid_max:rw-' > ksym_trace_filter
 bash: echo: write error: Invalid argument

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A52E2EB.9070503@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:59:42 +02:00
Li Zefan
f088e54712 ksym_tracer: Fix validation of access type
# echo 'pid_max:rw-' > ksym_trace_filter
 # cat ksym_trace_filter
 pid_max:rw-
 # echo 'pid_max:ww-' > ksym_trace_filter
 (should return -EINVAL)
 # cat ksym_trace_filter
 (but it ended up removing filter entry)

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A52E2CE.6080409@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:59:41 +02:00
Li Zefan
be9742e6cb ksym_tracer: Rewrite ksym_trace_filter_read()
Reading ksym_trace_filter gave me some arbitrary characters,
when it should show nothing. It's because buf is not initialized
when there's no filter.

Also reduce stack usage by about 512 bytes.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A52E2B4.6030706@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:59:40 +02:00
Li Zefan
db59504d89 ksym_tracer: Extract trace entry from struct trace_ksym
struct trace_ksym is used as an entry in hbp list, and is also
used as trace_entry stored in ring buffer.

This is not necessary and is a waste of memory in ring buffer.

There is also a bug that dereferencing field->ksym_hbp in
ksym_trace_output() can be invalid.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A52E2A4.4050007@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:59:40 +02:00
Xiao Guangrong
dc82ec98a4 tracing/filter: Remove empty subsystem and its directory
Remove empty subsystem and its directory when module unload.

Before patch:
 # rmmod trace-events-sample.ko
 # ls sample
 enable  filter

After patch:
 # rmmod trace-events-sample.ko
 # ls sample
 ls: cannot access sample: No such file or directory

Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Acked-by: Tom Zanussi <tzanussi@gmail.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A55A8BE.9010707@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:55:28 +02:00
Xiao Guangrong
c5cb183608 tracing/filter: Remove preds from struct event_subsystem
No need to save preds to event_subsystem, because it's not used.

Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Acked-by: Tom Zanussi <tzanussi@gmail.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4A55A83C.1030005@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 11:55:27 +02:00
Takashi Iwai
3ae3079666 Merge branch 'fix/hda' into for-linus
* fix/hda:
  ALSA: hda - targa and targa-2ch fix
  ALSA: hda - fix beep tone calculation for IDT/STAC codecs
  ALSA: hda - Missing volume controls for Intel HDA (ALC269/EeePC)
  ALSA: hda - Disable AMD SB600 64bit address support only
  ALSA: hda - Check widget types while parsing capture source in patch_via.c
  ALSA: hda - Fix capture source selection in patch_via.c
  ALSA: hda - Add missing EAPD initialization for VIA codecs
  ALSA: hda - Clean up VT170x dig-in initialization code
  ALSA: hda - Fix error path in the sanity check in azx_pcm_open()
  ALSA: hda - move 8086:fb30 quirk (stac9205) to the proper section
2009-07-10 11:17:12 +02:00
Takashi Iwai
f371f12f3e Merge branch 'fix/asoc' into for-linus
* fix/asoc:
  ASoC: Fix wm8753 register cache size and initialization
  ASoC: add locking to mpc5200-psc-ac97 driver
  ASoC: Fix mpc5200-psc-ac97 to ensure the data ready bit is cleared
  ASoC: Fix register cache initialisation for WM8753
2009-07-10 11:17:11 +02:00
Fabio Checconi
c20b08e398 sched: Fix rt_rq->pushable_tasks initialization in init_rt_rq()
init_rt_rq() initializes only rq->rt.pushable_tasks, and not the
pushable_tasks field of the passed rt_rq.  The plist is not used
uninitialized since the only pushable_tasks plists used are the
ones of root rt_rqs; anyway reinitializing the list on every group
creation corrupts the root plist, losing its previous contents.

Signed-off-by: Fabio Checconi <fabio@gandalf.sssup.it>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090615185638.GK21741@gandalf.sssup.it>
CC: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 10:43:30 +02:00
Lucas De Marchi
7793527b90 sched: Reset sched stats on fork()
The sched_stat fields are currently not reset upon fork.
Ingo's recent commit 6c594c21fc
did reset nr_migrations, but it didn't reset any of the
others.

This patch resets all sched_stat fields on fork.

Signed-off-by: Lucas De Marchi <lucas.de.marchi@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <193b0f820907090457s7a3662f4gcdecdc22fcae857b@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-07-10 10:43:29 +02:00