Commit graph

932,869 commits

Author SHA1 Message Date
Jesse Brandeburg
9a1a69adad ixgbe: Fix the Tx clean logic to return proper status
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status.  The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:11 -07:00
Jesse Brandeburg
4dd64df895 ixgbe: fix bug with napi add before request_irq
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.

Solution: call napi_add before calling request_irq

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:10 -07:00
Jesse Brandeburg
509ee935ec ixgbe: Fix interrupt configuration for 82599
The interrupt models using EITR have changed in 82599.  The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't.  This patch fixes all the cases where EITR
handling is different than 82598.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:08 -07:00
PJ Waskiewicz
40dcd79a7b ixgbe: Disable DROP_EN for Rx queues
82599 mistakenly enabled drop on Rx queues in the packet buffer.  The
default mode should be store-and-forward from the FIFO.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:07 -07:00
PJ Waskiewicz
d51019a4da ixgbe: Fix an accounting problem when the Rx FIFO is full
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly.  In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:07 -07:00
PJ Waskiewicz
1339b9e975 ixgbe: Fix get_supported_physical_layer() due to new 82599 PHY types
A purely cosmetic change.  Report which physical layer is present, instead
of PHY unknown.  82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:06 -07:00
Alexander Duyck
c8ea5ea9da igb: add support for 82576 quad copper adapter
Add support for 82576 copper adapter and necessary code to restrict wol for
quad port adapter to first port.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:06 -07:00
Alexander Duyck
9eb2341d0d igb: add support for another dual port 82576 non-security nic
Adding device id to support 82576NS dual port copper
NIC.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:05 -07:00
Alexander Duyck
75f4f382e3 igb: correct typo that was setting vfta mask to 1
This patch corrects a typo that was doing a less than comparison instead of
a left shift due to the fact that I didn't get enough <'s in there.

This resolves an issue in which vlans were not functioning correctly.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:04 -07:00
Alexander Duyck
cad6d05f56 igb: add PF to pool
Add Pf to pool if adding a VLVF register value and the VFTA bit is
already set.

This patch addresses the unlikely situation that the PF adds a vlan
entry when the vlvf is full, and a vf later adds the vlan to the vlvf.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:03 -07:00
Alexander Duyck
a2cf8b6ce1 igb: support wol on second port
We need to support wol on the second port for situations such as when the
lan ports are on the motherboard itself.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:03 -07:00
Alexander Duyck
bd38e5d124 igb: resolve warning of unused adapter struct
If DCA is undefined then the adapter struct becomes unnecessary.  To
resolve this issue the DCA calls can simply make a call to the adapter
struct through the rx_ring adapter struct member.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:02 -07:00
Alexander Duyck
5e6d5b17db igb: remove netif running call from igb_poll
The netif_running check in igb poll is a hold over from the use of fake
netdevs to use multiple queues with NAPI prior to 2.6.24.  It is no longer
necessary to have the call there and it currently can cause errors if
work_done == budget.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:01 -07:00
Maciej Sosnowski
92be791759 igb: switch to new dca API
With the new DCA API, the driver should use dca3_get_tag() instead of
the obsolete dca_get_tag().

Signed-off-by: Maciej Sosnowski < maciej.sosnowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:01 -07:00
Linus Torvalds
326d8519fc Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Mark Eins: Fix configuration.
  MIPS: Fix TIF_32BIT undefined problem when seccomp is disabled
2009-03-14 12:02:21 -07:00
Linus Torvalds
228b5b7e84 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits)
  [SCSI] qla2xxx: Update version number to 8.03.00-k4.
  [SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size.
  [SCSI] qla2xxx: Correct truncation in return-code status checking.
  [SCSI] qla2xxx: Correct vport delete bug.
  [SCSI] qla2xxx: Use correct value for max vport in LOOP topology.
  [SCSI] qla2xxx: Correct address range checking for option-rom updates.
  [SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20
  [SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3)
  [SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status
  [SCSI] fcoe: fix kfree(skb)
  [SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway
  [SCSI] libfc: do not change the fh_rx_id of a recevied frame
  [SCSI] fcoe: Correct fcoe_transports initialization vs. registration
  [SCSI] fcoe: Use setup_timer() and mod_timer()
  [SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper
  [SCSI] libfc, fcoe: Cleanup function formatting and minor typos
  [SCSI] libfc, fcoe: Fix kerneldoc comments
  [SCSI] libfc: Cleanup libfc_function_template comments
  [SCSI] libfc: check for err when recv and state is incorrect
  [SCSI] libfc: rename rp to rdata in fc_disc_new_target()
  ...
2009-03-14 12:01:37 -07:00
Linus Torvalds
37e79a43ac Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata_piix: add workaround for Samsung DB-P70
  libata: Keep shadow last_ctl up to date during resets
  sata_mv: fix MSI irq race condition
2009-03-14 12:00:42 -07:00
Linus Torvalds
f1823acfbc Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Fix the fix to Bugzilla #11061, when IPv6 isn't defined...
  SUNRPC: xprt_connect() don't abort the task if the transport isn't bound
  SUNRPC: Fix an Oops due to socket not set up yet...
  Bug 11061, NFS mounts dropped
  NFS: Handle -ESTALE error in access()
  NLM: Fix GRANT callback address comparison when IPv6 is enabled
  NLM: Shrink the IPv4-only version of nlm_cmp_addr()
  NFSv3: Fix posix ACL code
  NFS: Fix misparsing of nfsv4 fs_locations attribute (take 2)
  SUNRPC: Tighten up the task locking rules in __rpc_execute()
2009-03-14 12:00:18 -07:00
Linus Torvalds
ff9cb43ce0 Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
  ocfs2: Use xs->bucket to set xattr value outside
  ocfs2: Fix a bug found by sparse check.
  ocfs2: tweak to get the maximum inline data size with xattr
  ocfs2: reserve xattr block for new directory with inline data
2009-03-14 11:59:22 -07:00
Linus Torvalds
2a4c13baeb Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (10978): Report tuning algorith correctly
  V4L/DVB (10977): STB6100 init fix, the call to stb6100_set_bandwidth needs an argument
  V4L/DVB (10976): Bug fix: For legacy applications stv0899 performs search only first time after insmod.
  V4L/DVB (10975): Bug: Use signed types, Offsets and range can be negative
  V4L/DVB (10974): Use Diseqc 3/3 mode to send data
  V4L/DVB (10972): zl10353: i2c_gate_ctrl bug fix
  V4L/DVB (10834): zoran: auto-select bt866 for AverMedia 6 Eyes
  V4L/DVB (10832): tvaudio: Avoid breakage with tda9874a
  V4L/DVB (10789): m5602-s5k4aa: Split up the initial sensor probe in chunks.
2009-03-14 11:59:05 -07:00
Linus Torvalds
bf9bc995a5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6.29
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6.29:
  parisc: update defconfigs
  parisc: define x->x mmio accessors
  parisc: dino: struct device - replace bus_id with dev_name(), dev_set_name()
  parisc: convert cpu_check_affinity to new cpumask api
  parisc: convert (read|write)bwlq to inlines
  parisc: fix use of new cpumask api in irq.c
  parisc: update parisc for new irq_desc
  parisc: update MAINTAINERS
  parisc: fix wrong assumption about bus->self
  parisc: fix 64bit build
  parisc: add braces around arguments in assembler macros
  parisc: fix dev_printk() compile warnings for accessing a device struct
  parisc: remove unused local out_putf label
  parisc: fix `struct pt_regs' declared inside parameter list warning
  parisc: fix section mismatch warnings
  parisc: remove klist iterators
  parisc: BUG_ON() cleanup
2009-03-14 11:58:38 -07:00
Linus Torvalds
6d71135d63 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: save the returned value of dma_map_sg
  ide-floppy: do not map dataless cmds to an sg
2009-03-14 11:58:10 -07:00
Daisuke Nishimura
1d885526f2 vmscan: pgmoved should be cleared after updating recent_rotated
pgmoved should be cleared after updating recent_rotated.

Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Rik van Riel <riel@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-14 11:57:22 -07:00
Tyler Hicks
84814d642a eCryptfs: don't encrypt file key with filename key
eCryptfs has file encryption keys (FEK), file encryption key encryption
keys (FEKEK), and filename encryption keys (FNEK).  The per-file FEK is
encrypted with one or more FEKEKs and stored in the header of the
encrypted file.  I noticed that the FEK is also being encrypted by the
FNEK.  This is a problem if a user wants to use a different FNEK than
their FEKEK, as their file contents will still be accessible with the
FNEK.

This is a minimalistic patch which prevents the FNEKs signatures from
being copied to the inode signatures list.  Ultimately, it keeps the FEK
from being encrypted with a FNEK.

Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Acked-by: Dustin Kirkland <kirkland@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-14 11:57:22 -07:00
Johannes Weiner
15e7b87676 nommu: ramfs: don't leak pages when adding to page cache fails
When a ramfs nommu mapping is expanded, contiguous pages are allocated
and added to the pagecache.  The caller's reference is then passed on
by moving whole pagevecs to the file lru list.

If the page cache adding fails, make sure that the error path also
moves the pagevec contents which might still contain up to PAGEVEC_SIZE
successfully added pages, of which we would leak references otherwise.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Enrik Berkhan <Enrik.Berkhan@ge.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-14 11:57:22 -07:00
Enrik Berkhan
020fe22ff1 nommu: ramfs: pages allocated to an inode's pagecache may get wrongly discarded
The pages attached to a ramfs inode's pagecache by truncation from nothing
- as done by SYSV SHM for example - may get discarded under memory
pressure.

The problem is that the pages are not marked dirty.  Anything that creates
data in an MMU-based ramfs will cause the pages holding that data will
cause the set_page_dirty() aop to be called.

For the NOMMU-based mmap, set_page_dirty() may be called by write(), but
it won't be called by page-writing faults on writable mmaps, and it isn't
called by ramfs_nommu_expand_for_mapping() when a file is being truncated
from nothing to allocate a contiguous run.

The solution is to mark the pages dirty at the point of allocation by the
truncation code.

Signed-off-by: Enrik Berkhan <Enrik.Berkhan@ge.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-14 11:57:22 -07:00
Dhananjay Phadke
de9307c686 netxen: remove old flash check.
Remove flash size check which made sense only for ancient
boards with 1MB flash. The check is based on values read
from specific locations and fails with firmware size changes.

This prevents driver from getting right mac addresses.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 11:40:08 -07:00
Jaswinder Singh Rajput
f4c3c4cdb1 x86: cpu_debug add support for various AMD CPUs
Impact: Added AMD CPUs support

Added flags for various AMD CPUs.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 18:07:58 +01:00
Eric Sandeen
8d03c7a0c5 ext4: fix bogus BUG_ONs in in mballoc code
Thiemo Nagel reported that:

# dd if=/dev/zero of=image.ext4 bs=1M count=2
# mkfs.ext4 -v -F -b 1024 -m 0 -g 512 -G 4 -I 128 -N 1 \
  -O large_file,dir_index,flex_bg,extent,sparse_super image.ext4
# mount -o loop image.ext4 mnt/
# dd if=/dev/zero of=mnt/file

oopsed, with a BUG_ON in ext4_mb_normalize_request because
size == EXT4_BLOCKS_PER_GROUP

It appears to me (esp. after talking to Andreas) that the BUG_ON
is bogus; a request of exactly EXT4_BLOCKS_PER_GROUP should
be allowed, though larger sizes do indicate a problem.

Fix that an another (apparently rare) codepath with a similar check.

Reported-by: Thiemo Nagel <thiemo.nagel@ph.tum.de>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2009-03-14 11:51:46 -04:00
Sebastian Andrzej Siewior
48f4c485c2 x86/centaur: merge 32 & 64 bit version
there should be no difference, except:

 * the 64bit variant now also initializes the padlock unit.
 * ->c_early_init() is executed again from ->c_init()
 * the 64bit fixups made into 32bit path.

Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: herbert@gondor.apana.org.au
LKML-Reference: <1237029843-28076-2-git-send-email-sebastian@breakpoint.cc>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 16:27:29 +01:00
Ingo Molnar
0ca0f16fd1 Merge branches 'x86/apic', 'x86/asm', 'x86/cleanups', 'x86/debug', 'x86/kconfig', 'x86/mm', 'x86/ptrace', 'x86/setup' and 'x86/urgent'; commit 'v2.6.29-rc8' into x86/core 2009-03-14 16:25:40 +01:00
Adrian Hunter
f55aa59106 UBIFS: fix bug where page is marked uptodate when out of space
UBIFS fast path in write_begin may mark a page up to date
and then discover that there may not be enough space to do
the write, and so fall back to a slow path.  The slow path
tries harder, but may still find no space - leaving the page
marked up to date, when it is not.  This patch ensures that
the page is marked not up to date in that case.

The bug that this patch fixes becomes evident when the write
is into a hole (sparse file) or is at the end of the file
and a subsequent read is off the end of the file.  In both
cases, the file system should return zeros but was instead
returning the page that had not been written because the
file system was out of space.

Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2009-03-14 16:46:33 +02:00
Matthew Wilcox
0da205e01b [SCSI] sd: Refactor sd_read_capacity()
The sd_read_capacity() function was about 180 lines long and
included a backwards goto and a tricky state variable.  Splitting out
read_capacity_10() and read_capacity_16() (about 50 lines each) reduces
sd_read_capacity to about 100 lines and gets rid of the backwards goto
and the state variable.  I've tried to avoid any behaviour change with
this patch.

[jejb: upped transfer request to standard recommended 32 for RC16]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-03-14 08:42:56 -05:00
Mark Brown
85fab7802a ASoC: Fix Zylonite for non-networked SSP mode
This also simplifies the code a bit.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-03-14 11:38:16 +00:00
Mark Brown
0ce36c5f7f ASoC: Fix non-networked I2S mode for PXA SSP
Two issues are fixed here:

 - I2S transmits the left frame with the clock low but I don't seem to
   get LRCLK out without SFRMDLY being set so invert SFRMP and set a
   delay.
 - I2S has a clock cycle prior to the first data byte in each channel
   so we need to delay the data by one cycle.

Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-03-14 11:37:46 +00:00
Vegard Nossum
ed681a91ab vsprintf: unify the format decoding layer for its 3 users, cleanup
Impact: cleanup

Rename FORMAT_TYPE_WITDH
 to => FORMAT_TYPE_WIDTH

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 12:37:09 +01:00
Vegard Nossum
adf26f84a6 fix regression from "vsprintf: unify the format decoding layer for its 3 users"
Jeremy Fitzhardinge reported:

> Change fef20d9c13, "vsprintf:
> unify the format decoding layer for its 3 users", causes a
> regression in xenbus which results in no devices getting
> attached to a new domain.

%.*s is broken - fix it.

Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 12:37:08 +01:00
Yinghai Lu
d4c90e37a2 x86: print the continous part of fixed mtrrs together
Impact: print out fewer lines

 1. print continuous range with same type together
 2. change _INFO to _DEBUG

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BACB61.8000302@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 12:27:06 +01:00
Yinghai Lu
63516ef6d6 x86: fix get_mtrr() warning about smp_processor_id() with CONFIG_PREEMPT=y
Impact: fix debug warning

Jaswinder noticed that there is a warning about smp_processor_id()
in get_mtrr().

Fix it by wrapping the printout into a get/put_cpu() pair.

Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <49BAB7FF.4030107@kernel.org>
[ changed to get/put_cpu(), cleaned up surrounding code a it. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 12:27:06 +01:00
Yinghai Lu
78a8b35bc7 x86: make e820_update_range() handle small range update
Impact: enhance e820 code to handle more cases

Try to handle new range which could be covered by one entry.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: jbeulich@novell.com
LKML-Reference: <49B9F0C1.10402@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 12:20:07 +01:00
Ingo Molnar
0f3fa48a7e x86: cpu/common.c more cleanups
Complete/fix the cleanups of cpu/common.c:

 - fix ugly warning due to asm/topology.h -> linux/topology.h change
 - standardize the style across the file
 - simplify/refactor the code flow where possible

Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
LKML-Reference: <1237009789.4387.2.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 10:37:34 +01:00
Lai Jiangshan
b478b782e1 kallsyms, tracing: output more proper symbol name
Impact: bugfix, output more reliable symbol lookup result

Debug tools(dump_stack(), ftrace...) are like to print out symbols.
But it is always print out the first aliased symbol.(Aliased symbols
are symbols with the same address), and the first aliased symbol is
sometime not proper.

 # echo function_graph > current_tracer
 # cat trace
......
 1)   1.923 us    |    select_nohz_load_balancer();
 1) + 76.692 us   |  }
 1)               |  default_idle() {
 1)   ==========> |    __irqentry_text_start() {
 1)   0.000 us    |      native_apic_mem_write();
 1)               |      irq_enter() {
 1)   0.000 us    |        idle_cpu();
 1)               |        tick_check_idle() {
 1)   0.000 us    |          tick_check_oneshot_broadcast();
 1)               |          tick_nohz_stop_idle() {
......

It's very embarrassing, it ouputs "__irqentry_text_start()",
actually, it should output "smp_apic_timer_interrupt()".
(these two symbol are the same address, but "__irqentry_text_start"
is deemed to the first aliased symbol by scripts/kallsyms)

This patch puts symbols like "__irqentry_text_start" to the second
aliased symbols. And a more proper symbol name becomes the first.

Aliased symbols mostly come from linker script. The solution is
guessing "is this symbol defined in linker script", the symbols
defined in linker script will not become the first aliased symbol.

And if symbols are found to be equal in this "linker script provided"
criteria, symbols are sorted by the number of prefix underscores.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Paulo Marques <pmarques@grupopie.com>
LKML-Reference: <49BA06E2.7080807@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 09:55:04 +01:00
Ingo Molnar
c550033ced Merge branch 'core/percpu' into x86/core 2009-03-14 09:50:10 +01:00
Pallipadi, Venkatesh
895791dac6 VM, x86, PAT: add a new vm flag to track full pfnmap at mmap
Impact: cleanup

Add a new vm flag VM_PFN_AT_MMAP to identify a PFNMAP that is
fully mapped with remap_pfn_range. Patch removes the overloading
of VM_INSERTPAGE from the earlier patch.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Nick Piggin <npiggin@suse.de>
LKML-Reference: <20090313233543.GA19909@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 09:47:44 +01:00
Ingo Molnar
62395efdb0 Merge branch 'x86/asm' into tracing/syscalls
We need the wider TIF work-mask checks in entry_32.S.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 09:44:08 +01:00
Jaswinder Singh Rajput
88200bc28d x86: entry_32.S fix compile warnings - fix work mask bit width
Fix:

 arch/x86/kernel/entry_32.S:446: Warning: 00000000080001d1 shortened to 00000000000001d1
 arch/x86/kernel/entry_32.S:457: Warning: 000000000800feff shortened to 000000000000feff
 arch/x86/kernel/entry_32.S:527: Warning: 00000000080001d1 shortened to 00000000000001d1
 arch/x86/kernel/entry_32.S:541: Warning: 000000000800feff shortened to 000000000000feff
 arch/x86/kernel/entry_32.S:676: Warning: 0000000008000091 shortened to 0000000000000091

TIF_SYSCALL_FTRACE is 0x08000000 and until now we checked the
first 16 bits of the work mask - bit 27 falls outside of that.

Update the entry_32.S code to check the full 32-bit mask.

[ %cx => %ecx fix from Cyrill Gorcunov <gorcunov@gmail.com> ]

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "H. Peter Anvin" <hpa@kernel.org>
LKML-Reference: <1237012693.18733.3.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 09:42:51 +01:00
Jaswinder Singh Rajput
9766cdbcb2 x86: cpu/common.c cleanups
- fix various style problems
 - declare varibles before they get used
 - introduced clear_all_debug_regs
 - fix header files issues

LKML-Reference: <1237009789.4387.2.camel@localhost.localdomain>
Signed-off-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-03-14 08:59:50 +01:00
Gabriele Paoloni
9c705260fe ppp: ppp_mp_explode() redesign
I found the PPP subsystem to not work properly when connecting channels
with different speeds to the same bundle.

Problem Description:

As the "ppp_mp_explode" function fragments the sk_buff buffer evenly
among the PPP channels that are connected to a certain PPP unit to
make up a bundle, if we are transmitting using an upper layer protocol
that requires an Ack before sending the next packet (like TCP/IP for
example), we will have a bandwidth bottleneck on the slowest channel
of the bundle.

Let's clarify by an example. Let's consider a scenario where we have
two PPP links making up a bundle: a slow link (10KB/sec) and a fast
link (1000KB/sec) working at the best (full bandwidth). On the top we
have a TCP/IP stack sending a 1000 Bytes sk_buff buffer down to the
PPP subsystem. The "ppp_mp_explode" function will divide the buffer in
two fragments of 500B each (we are neglecting all the headers, crc,
flags etc?.). Before the TCP/IP stack sends out the next buffer, it
will have to wait for the ACK response from the remote peer, so it
will have to wait for both fragments to have been sent over the two
PPP links, received by the remote peer and reconstructed. The
resulting behaviour is that, rather than having a bundle working
@1010KB/sec (the sum of the channels bandwidths), we'll have a bundle
working @20KB/sec (the double of the slowest channels bandwidth).


Problem Solution:

The problem has been solved by redesigning the "ppp_mp_explode"
function in such a way to make it split the sk_buff buffer according
to the speeds of the underlying PPP channels (the speeds of the serial
interfaces respectively attached to the PPP channels). Referring to
the above example, the redesigned "ppp_mp_explode" function will now
divide the 1000 Bytes buffer into two fragments whose sizes are set
according to the speeds of the channels where they are going to be
sent on (e.g .  10 Byets on 10KB/sec channel and 990 Bytes on
1000KB/sec channel).  The reworked function grants the same
performances of the original one in optimal working conditions (i.e. a
bundle made up of PPP links all working at the same speed), while
greatly improving performances on the bundles made up of channels
working at different speeds.

Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13 16:09:12 -07:00
Roel Kluin
a2025b8b10 tcp: '< 0' test on unsigned
promote 'cnt' to size_t, to match 'len'.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13 16:05:14 -07:00
Roel Kluin
8db09f26f9 x25: '< 0' and '>= 0' test on unsigned
skb->len is an unsigned int, so the test in x25_rx_call_request() always
evaluates to true.

len in x25_sendmsg() is unsigned as well. so -ERRORS returned by x25_output()
are not noticed.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13 16:04:12 -07:00