Require framepointers for x86, because otherwise we'll be having
empty stack traces, which is useless.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1236167295.5330.7240.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clarify lockdep printk text
print_irq_inversion_bug() gets handed state strings of the form
"HARDIRQ", "SOFTIRQ", "RECLAIM_FS"
and appends "-irq-{un,}safe" to them, which is either redudant for *IRQ or
confusing in the RECLAIM_FS case.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1236175192.5330.7585.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the recent mark_lock_irq() rework a bug snuck in that would report the
state of write locks causing irq inversion under a read lock as a read
lock.
Fix this by masking the read bit of the state when validating write
dependencies.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1236172646.5330.7450.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When setting WM8510_MCLKDIV the pll was turned off.
When setting pll frequency you got twice the expected freq, because
the code calculated with postscaler of 8, but the hardware divide by 4.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add GPIO support to jack reporting framework in ASoC using gpiolib calls.
The gpio support exports two new functions: snd_soc_jack_add_gpios and
snd_soc_jack_free_gpios.
Client drivers using gpio feature must pass an array of jack_gpio pins
belonging to a specific jack to the snd_soc_jack_add_gpios function. The
framework will request the gpios, set the data direction and request irq.
The framework will update power status of related jack_pins when an event on
the gpio pins comes according to the reporting bits defined for each gpio.
All gpio resources allocated when adding jack_gpio pins can be released
using snd_soc_jack_free_gpios function.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we unconditionally issue a flush from xfs_free_buftarg, but
since 2.6.29-rc1 this gives a warning in the style of
end_request: I/O error, dev vdb, sector 0
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
The inode can't be locked by anyone else as we just created it a few
lines above and it's not been added to any lookup data structure yet.
So use a trylock that must succeed to get around the lockdep warnings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Andras Korn reported an oops on log replay causes by a corrupted
xfs_inode_log_format_t passing a 0 size to kmem_zalloc. This patch handles
to small or too large numbers of log regions gracefully by rejecting the
log replay with a useful error message.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Andras Korn <korn-sgi.com@chardonnay.math.bme.hu>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Change sctp_ctl_sock_init() to try IPv4 if IPv6 socket registration
fails. Required if the IPv6 module is loaded with "disable=1", else
SCTP will fail to load.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "disable" module parameter support to ipv6.ko by specifying
"disable=1" on module load. We just do the minimum of initializing
inetsw6[] so calls from other modules to inet6_register_protosw()
won't OOPs, then bail out. No IPv6 addresses or sockets can be
created as a result, and a reboot is required to enable IPv6.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: build fix
The APIC code rewrite in the x86 tree broke the x86/mce branch:
arch/x86/kernel/cpu/mcheck/threshold.c: In function ‘mce_threshold_interrupt’:
arch/x86/kernel/cpu/mcheck/threshold.c:24: error: implicit declaration of function ‘ack_APIC_irq’
Also tidy up the file a bit while at it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
The function is identical on 32-bit and 64-bit configurations so move
it to the common mm/init.c file.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <1236160001.29024.29.camel@penberg-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The recent update enabled the model=sony-assamd for all ALC262 with
PCI SSID 104d:90xx. But this includes the VAIO VGN-AR* that has the
primary codec of STAC92xx and the secondary ALC262 as a slave
digital-only codec. For this device, the model=auto must be chosen
to work properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Impact: ABI change
This expands several fields in the perf_counter_hw_event struct and adds
a "flags" argument to the perf_counter_open system call, in order that
features can be added in future without ABI changes.
In particular the record_type field is expanded to 64 bits, and the
space for flag bits has been expanded from 32 to 64 bits.
This also adds some new fields:
* read_format (64 bits) is intended to provide a way to specify what
userspace wants to get back when it does a read() on a simple
(non-interrupting) counter;
* exclude_idle (1 bit) provides a way for userspace to ask that events
that occur when the cpu is idle be excluded;
* extra_config_len will provide a way for userspace to supply an
arbitrary amount of extra machine-specific PMU configuration data
immediately following the perf_counter_hw_event struct, to allow
sophisticated users to program things such as instruction matching
CAMs and address range registers;
* __reserved_3 and __reserved_4 provide space for future expansion.
Signed-off-by: Paul Mackerras <paulus@samba.org>
wait_event_interruptible_timeout may return -ERESTARTSYS.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since early 2.5 kernels block drivers don't need to define MAJOR_NR
anymore, so use the JSFD_MAJOR defined directly and kill it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (i-- > 0); i reaches -1 after the loop, so the test below is printed
one too early: 0 still means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (--worklimit >= 0); worklimit reaches -1 after the loop. In
3c589_cs.c this caused a warning not to be printed.
In 3c574_cs.c contrastingly, el3_rx() treats worklimit differently:
static int el3_rx(struct net_device *dev, int worklimit)
{
while (--worklimit >= 0) { ... }
return worklimit;
}
el3_rx() is only called by function el3_interrupt(): twice:
static irqreturn_t el3_interrupt(int irq, void *dev_id)
{
int work_budget = max_interrupt_work;
while(...) {
if (...)
work_budget = el3_rx(dev, work_budget);
if (...)
work_budget = el3_rx(dev, work_budget);
if (--work_budget < 0) {
...
break;
}
}
}
The error path can occur 2 too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (timeout-- > 0); timeout reaches -1 after the loop, so the tests
below are off by one. also don't do an '< 0' test on an unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the mic input of HP dv6736 with Conexant 5051 codec chip.
This laptop seems have no mic-switching per jack connection.
A new model hp-dv6736 is introduced to match with the h/w implementation.
Reference: Novell bnc#480753
https://bugzilla.novell.com/show_bug.cgi?id=480753
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently it is possible to do just about everything with the arp table
from user space except treat an entry like you are using it. To that end
implement and a flag NTF_USE that when set in a netwlink update request
treats the neighbour table entry like the kernel does on the output path.
This allows user space applications to share the kernel's arp cache.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware is issuing events to the driver the events
must be removed from the queue. If the queue overflows, the
firmware will build and special event that captures those that
are lost.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This event will arrive at boot time or after an
MPI processor reset if the firmware failed to initialize.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, modular tokenring ("tr") lacks a license and fails to load:
tr: module license 'unspecified' taints kernel.
tr: Unknown symbol proc_net_fops_create
Beacuse of this, no tokenring driver can load if it depends on modular
tr. Fix this by adding GPL module license as it is in the kernel.
With this fix, tr module loads fine and tms380 driver also loads. Well,
it does'nt work but that's a different bug.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vendor/product IDs for new no name dm9601 compatible usb ethernet
adaptors.
Reported-by: Eric Lauriault <eric@linux.ca>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callers of netlink_set_err() currently pass a negative value
as parameter for the error code. However, sk->sk_err wants a
positive error value. Without this patch, skb_recv_datagram() called
by netlink_recvmsg() may return a positive value to report an error.
Another choice to fix this is to change callers to pass a positive
error value, but this seems a bit inconsistent and error prone
to me. Indeed, the callers of netlink_set_err() assumed that the
(usual) negative value for error codes was fine before this patch :).
This patch also includes some documentation in docbook format
for netlink_set_err() to avoid this sort of confusion.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation to only 1500 byte mtu's limits the utility of the veth
device for testing routing. So implement implement a configurable
MTU.
For consistency I drop packets on the receive side when they are
larger than the MTU. I count those drops. And I allow
a little padding for vlan headers.
I also test the mtu when a new device is created with netlink
because that path currently bypasses the current mtu setting
code.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current "comp" crypto interface supports one-shot (de)compression only,
i.e. the whole data buffer to be (de)compressed must be passed at once, and
the whole (de)compressed data buffer will be received at once.
In several use-cases (e.g. compressed file systems that store files in big
compressed blocks), this workflow is not suitable.
Furthermore, the "comp" type doesn't provide for the configuration of
(de)compression parameters, and always allocates workspace memory for both
compression and decompression, which may waste memory.
To solve this, add a "pcomp" partial (de)compression interface that provides
the following operations:
- crypto_compress_{init,update,final}() for compression,
- crypto_decompress_{init,update,final}() for decompression,
- crypto_{,de}compress_setup(), to configure (de)compression parameters
(incl. allocating workspace memory).
The (de)compression methods take a struct comp_request, which was mimicked
after the z_stream object in zlib, and contains buffer pointer and length
pairs for input and output.
The setup methods take an opaque parameter pointer and length pair. Parameters
are supposed to be encoded using netlink attributes, whose meanings depend on
the actual (name of the) (de)compression algorithm.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>