This removes the various DBG() macro from the powerpc PCI code and
makes it use the standard pr_debug instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update memcpy() to add two new feature sections: one for aligning the
destination before copying and one for copying using aligned load
and store doubles.
These new feature sections will only affect Power6 and Cell because
the CPU feature bit was only added to these two processors.
Power6 gets its best performance in memcpy() when aligning neither the
source nor the destination, while Cell gets its best performance when
just the destination is aligned. But in order to save on CPU feature
bits we can use the previously added CPU_FTR_CP_USE_DCBTZ feature bit
to differentiate between Power6 and Cell (because CPU_FTR_CP_USE_DCBTZ
was added to Cell but not Power6).
The first feature section acts to nop out the branch that takes us to
the code that aligns us to an eight byte boundary for the destination.
We only want to nop out this branch on Power6.
So the ALT_FTR_SECTION_END() for this feature section creates a test
mask of the two feature bits ORed together and provides an expected
result of just CPU_FTR_UNALIGNED_LD_STD, thus we nop out the branch
if we're on a CPU that has CPU_FTR_UNALIGNED_LD_STD set and
CPU_FTR_CP_USE_DCBTZ unset.
For the second feature section added, if we're on a CPU that has the
CPU_FTR_UNALIGNED_LD_STD bit set then we don't want to do the copy
with aligned loads and stores (and the appropriate shifting left and
right instructions), so we want to nop out the branch to
.Lsrc_unaligned.
The andi. used for this branch is moved to just above the branch
because this allows us to nop out both instructions with just one
feature section which gives us better performance and doesn't hurt
readability which two separate feature sections did.
Moving the andi. to just above the branch doesn't have any noticeable
negative effect on the remaining 64bit processors (the ones that
didn't have this feature bit added).
On Cell this simple modification results in an improvement to measured
memcpy() bandwidth of up to 50% in the hot cache case and up to 15% in
the cold cache case.
On Power6 we get memory bandwidth results that are up to three times
faster in the hot cache case and up to 50% faster in the cold cache
case.
Commit 2a9294369b ("powerpc: Add new CPU
feature: CPU_FTR_CP_USE_DCBTZ") was where CPU_FTR_CP_USE_DCBTZ was
added.
To say that Cell gets its best performance in memcpy() with just the
destination aligned is true but only for the reason that the indirect
shift and rotate instructions, sld and srd, are microcoded on Cell.
This means that either the destination or the source can be aligned,
but not both, and seeing as we get better performance with the
destination aligned we choose this option.
While we're at it make a one line change from cmpldi r1,... to
cmpldi cr1,... for consistency.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a new CPU feature bit, CPU_FTR_UNALIGNED_LD_STD, to be added
to the 64bit powerpc chips that can do unaligned load double and
store double without any performance hit.
This is added to Power6 and Cell and will be used in the next commit
to disable the code that gets the destination address aligned on
those CPUs where doing that doesn't improve performance.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A new field has been added to the VPA as a method for the client OS to
communicate to firmware the number of page-ins it is performing when
running collaborative memory overcommit. The hypervisor will use this
information to better determine if a partition is experiencing memory
pressure and needs more memory allocated to it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 'ibm,interrupt-server#-size' properties are not in the cpu nodes,
which is where we currently look for them, but rather live under the
interrupt source controller nodes (which have "ibm,ppc-xics" in their
compatible property).
This moves the code that looks for the ibm,interrupt-server#-size
properties from xics_update_irq_servers() into xics_init_IRQ().
Also this adds a check for mismatched sizes across the interrupt
source controller nodes. Not sure this is necessary as in this case
the firmware might be seriously busted.
This property only appears on POWER6 boxes and is only used in the
set-indicator(gqirm) call, and apparently firmware currently ignores
the value we pass. Nevertheless we need to fix it in case future
firmware versions use it.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't want to encourage the device_type usage. It isn't used in
the code, so we can simply remove it from the dts files.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When no hardware method is provided to sync the timebase registers
across the machine, and the platform doesn't sync them for us, then we
use a generic software implementation. Currently, the code for that
has many printks, and they don't have log levels. Most of the printks
are only useful for debugging the code, and since we haven't had any
problems with it for years, this turns them into pr_debug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code to properly expose domain numbers in /proc is somewhat
bogus on ppc64 as it depends on the "buid" field being non-0,
but that field is really pseries specific.
This removes that code and makes ppc64 use the same code as 32-bit
which effectively decides whether to expose domains based on
ppc_pci_flags set by the platform, and sets the default for 64-bit
to enable domains and enable compatibility for domain 0 (which
strips the domain number for domain 0 to help with X servers).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With some net devices types, an IPv6 address configured while the
interface was down can stay 'tentative' forever, even after the interface
is set up. In some case, pending IPv6 DADs are not executed when the
device becomes ready.
I observed this while doing some tests with kvm. If I assign an IPv6
address to my interface eth0 (kvm driver rtl8139) when it is still down
then the address is flagged tentative (IFA_F_TENTATIVE). Then, I set
eth0 up, and to my surprise, the address stays 'tentative', no DAD is
executed and the address can't be pinged.
I also observed the same behaviour, without kvm, with virtual interfaces
types macvlan and veth.
Some easy steps to reproduce the issue with macvlan:
1. ip link add link eth0 type macvlan
2. ip -6 addr add 2003::ab32/64 dev macvlan0
3. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
4. ip link set macvlan0 up
5. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
Address is still tentative
I think there's a bug in net/ipv6/addrconf.c, addrconf_notify():
addrconf_dad_run() is not always run when the interface is flagged IF_READY.
Currently it is only run when receiving NETDEV_CHANGE event. Looks like
some (virtual) devices doesn't send this event when becoming up.
For both NETDEV_UP and NETDEV_CHANGE events, when the interface becomes
ready, run_pending should be set to 1. Patch below.
'run_pending = 1' could be moved below the if/else block but it makes
the code less readable.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed a contention on udp_memory_allocated on regular UDP applications.
While tcp_memory_allocated is seldom used, it appears each incoming UDP frame
is currently touching udp_memory_allocated when queued, and when received by
application.
One possible solution is to use sk_mem_reclaim_partial() instead of
sk_mem_reclaim(), so that we keep a small reserve (less than one page)
of memory for each UDP socket.
We did something very similar on TCP side in commit
9993e7d313
([TCP]: Do not purge sk_forward_alloc entirely in tcp_delack_timer())
A more complex solution would need to convert prot->memory_allocated to
use a percpu_counter with batches of 64 or 128 pages.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings in net/9p.
Built cleanly on 7 arches.
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: scheduling order fix for group scheduling
For each level in the hierarchy, set the buddy to point to the right entity.
Therefore, when we do the hierarchical schedule, we have a fair chance of
ending up where we meant to.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: improve/change/fix wakeup-buddy scheduling
Currently we only have a forward looking buddy, that is, we prefer to
schedule to the task we last woke up, under the presumption that its
going to consume the data we just produced, and therefore will have
cache hot benefits.
This allows co-waking producer/consumer task pairs to run ahead of the
pack for a little while, keeping their cache warm. Without this, we
would interleave all pairs, utterly trashing the cache.
This patch introduces a backward looking buddy, that is, suppose that
in the above scenario, the consumer preempts the producer before it
can go to sleep, we will therefore miss the wakeup from consumer to
producer (its already running, after all), breaking the cycle and
reverting to the cache-trashing interleaved schedule pattern.
The backward buddy will try to schedule back to the task that woke us
up in case the forward buddy is not available, under the assumption
that the last task will be the one with the most cache hot task around
barring current.
This will basically allow a task to continue after it got preempted.
In order to avoid starvation, we allow either buddy to get wakeup_gran
ahead of the pack.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix cross-class preemption
Inter-class wakeup preemptions should go on class order.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In 777e208d40 we changed from outputting
field->cpu (a char) to iter->cpu (unsigned int), increasing the resulting
structure size by 3 bytes.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This gets rid of this build warning:
arch/powerpc/platforms/pseries/pci_dlpar.c: In function 'init_phb_dynamic':
arch/powerpc/platforms/pseries/pci_dlpar.c:192: warning: unused variable 'b'
This is one of the very few warnings left in a ppc64_defconfig build and
getting rid of it will make it easier to see future introduced ones (in
fact this was introduced very recently).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes this error on Cell when CONFIG_KEXEC = n:
arch/powerpc/platforms/cell/ras.c:299: error: implicit declaration of function 'crash_shutdown_register'
We have to include <asm/kexec.h> because it contains the dummy
definition of crash_shutdown_register that is used when
CONFIG_KEXEC=n, but <linux/kexec.h> doesn't include <asm/kexec.h> in
that case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compiling with CONFIG_SMP = n and CONFIG_PS3_LPM != n gives this error:
drivers/ps3/ps3-lpm.c:838: error: implicit declaration of function 'get_hard_smp_processor_id'
This fixes it. We have to include <asm/smp.h> rather than
<linux/smp.h> because the UP definition of get_hard_smp_processor_id()
is in <asm/smp.h>, and <linux/smp.h> only includes <asm/smp.h> if
CONFIG_SMP = y.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This inserts the required de-allocation routines for memory allocated
by feature negotiation in the socket destructors, replacing
dccp_feat_clean() in one instance.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides feature-negotiation initialisation for both DCCP sockets
and DCCP request_sockets, to support feature negotiation during
connection setup.
It also resolves a FIXME regarding the congestion control
initialisation.
Thanks to Wei Yongjun for help with the IPv6 side of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds list initial fields and list management functions for the
new feature negotiation implementation.
Thanks to Arnaldo for suggestions and improvements.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
A lookup table for feature-negotiation information, extracted from RFC
4340/42, is provided by this patch. All currently known features can
be found in this table, along with their feature location, their
default value, and type.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares for the new and extended feature-negotiation
routines.
The following feature-negotiation data structures are provided:
* a container for the various (SP or NN) values,
* symbolic state names to track feature states,
* an entry struct which holds all current information together,
* elementary functions to fill in and process these structures.
Entry structs are arranged as FIFO for the following reason: RFC 4340
specifies that if multiple options of the same type are present, they
are processed in the order of their appearance in the packet; which
means that this order needs to be preserved in the local data
structure (the later insertion code also respects this order).
The struct list_head has been chosen for the following reasons: the most
frequent operations are
* add new entry at tail (when receiving Change or setting socket
options);
* delete entry (when Confirm has been received);
* deep copy of entire list (cloning from listening socket onto
request socket).
The NN value has been set to 64 bit, which is a currently sufficient
upper limit (Sequence Window feature has 48 bit).
Thanks to Arnaldo, who contributed the streamlined layout of the entry
struct.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Asus V1s series laptops have an ALC660VD with PCI id: 0x1043, 0x1633.
1.) remove the previous behaviour of mapping that to the ALC861VD_LENOVO
device.
2.) add a new ALC660VD_V1S device based on ALC861VD_LENOVO, with an
added digital out.
Signed-off-by: Tristan Aston <astrotris@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a proper ifdef to shut out a compile warning:
CC [M] sound/pci/hda/patch_intelhdmi.o
sound/pci/hda/patch_intelhdmi.c:286: warning: ‘hdmi_get_dip_index’ defined but \
not used
Signed-off-by: Takashi Iwai <tiwai@suse.de>
jbd2_log_do_checkpoint()n is one of the kernel's largest stack users.
Move the array of buffer head's from the stack of jbd2_log_do_checkpoint()
to the in-core journal structure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Convert the unsigned longs that are most responsible for bloating the
stack usage on 64-bit systems.
Nearly all places in the ext3/4 code which uses "unsigned long" is
probably a bug, since on 32-bit systems a ulong a 32-bits, which means
we are wasting stack space on 64-bit systems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Nearly all places in the ext3/4 code which uses "unsigned long" is
probably a bug, since on 32-bit systems a ulong a 32-bits, which means
we are wasting stack space on 64-bit systems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The i_ext_generation was incremented, but never used. Remove it to
slim down the ext4_inode_info structure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add new mount options, min_batch_time and max_batch_time, which
controls how long the jbd2 layer should wait for additional filesystem
operations to get batched with a synchronous write transaction.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Display the average commit time (which is used by the ext4 fsync
batching patch) in /proc/fs/jbd2/*/info for performance tuning
purposes.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch removes the static sleep time in favor of a more self
optimizing approach where we measure the average amount of time it
takes to commit a transaction to disk and the ammount of time a
transaction has been running. If somebody does a sync write or an
fsync() traditionally we would sleep for 1 jiffies, which depending on
the value of HZ could be a significant amount of time compared to how
long it takes to commit a transaction to the underlying storage. With
this patch instead of sleeping for a jiffie, we check to see if the
amount of time this transaction has been running is less than the
average commit time, and if it is we sleep for the delta using
schedule_hrtimeout to give us a higher precision sleep time. This
greatly benefits high end storage where you could end up sleeping for
longer than it takes to commit the transaction and therefore sitting
idle instead of allowing the transaction to be committed by keeping
the sleep time to a minimum so you are sure to always be doing
something.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We can call ext4_mb_check_limits even after successfully allocating
the requested blocks. In that case, make sure we don't overwrite
ac_status if it already has the status AC_STATUS_FOUND. This fixes
the lockdep warning:
=============================================
[ INFO: possible recursive locking detected ]
2.6.28-rc6-autokern1 #1
---------------------------------------------
fsstress/11948 is trying to acquire lock:
(&meta_group_info[i]->alloc_sem){----}, at: [<c04d9a49>] ext4_mb_load_buddy+0x9f/0x278
.....
stack backtrace:
.....
[<c04db974>] ext4_mb_regular_allocator+0xbb5/0xd44
.....
but task is already holding lock:
(&meta_group_info[i]->alloc_sem){----}, at: [<c04d9a49>] ext4_mb_load_buddy+0x9f/0x278
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
This removes annoying blank syslog entries emitted by ext4_error() or
ext4_warning(), since these functions add their own newline.
Signed-off-by: Nick Warne <nick@ukfsn.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Xen doesn't report that barriers are not supported until buffer I/O is
reported as completed, instead of when the buffer I/O is submitted.
Add a check and a fallback codepath to journal_wait_on_commit_record()
to detect this case, so that attempts to mount ext4 filesystems on
LVM/devicemapper devices on Xen guests don't blow up with an "Aborting
journal on device XXX"; "Remounting filesystem read-only" error.
Thanks to Andreas Sundstrom for reporting this issue.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
A few weeks ago I posted a patch for discussion that allowed ext4 to run
without a journal. Since that time I've integrated the excellent
comments from Andreas and fixed several serious bugs. We're currently
running with this patch and generating some performance numbers against
both ext2 (with backported reservations code) and ext4 with and without
a journal. It just so happens that running without a journal is
slightly faster for most everything.
We did
iozone -T -t 4 s 2g -r 256k -T -I -i0 -i1 -i2
which creates 4 threads, each of which create and do reads and writes on
a 2G file, with a buffer size of 256K, using O_DIRECT for all file opens
to bypass the page cache. Results:
ext2 ext4, default ext4, no journal
initial writes 13.0 MB/s 15.4 MB/s 15.7 MB/s
rewrites 13.1 MB/s 15.6 MB/s 15.9 MB/s
reads 15.2 MB/s 16.9 MB/s 17.2 MB/s
re-reads 15.3 MB/s 16.9 MB/s 17.2 MB/s
random readers 5.6 MB/s 5.6 MB/s 5.7 MB/s
random writers 5.1 MB/s 5.3 MB/s 5.4 MB/s
So it seems that, so far, this was a useful exercise.
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
I chased the cause of following ext4 oops report which is tested on
ia64 box.
http://bugzilla.kernel.org/show_bug.cgi?id=12018
The cause is the size of s_mb_maxs array that is defined as "unsigned
short" in ext4_sb_info structure. If the file system's block size is
8k or greater, an unsigned short is not wide enough to contain the
value fs->blocksize << 3.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Cc: stable@kernel.org
The inode table has been zeroed in setup_new_group_blocks(). Mark it as
such in ext4_group_add(). Since we are currently clearing inode table
for the new block group, we should set the EXT4_BG_INODE_ZEROED flag.
If at some point in the future we don't immediately zero out the inode
table as part of the resize operation, then obviously we shouldn't do
this.
Signed-off-by: Solofo.Ramangalahy@bull.net
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add this so that file systems using JBD2 can safely allocate unused b_state
bits.
In this case, we add it so that Ocfs2 can define a single bit for tracking
the validation state of a buffer.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Remove some completely unneeded code which which caused an ext4_error
to be generated when mounting a file system with only a single block
group.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
When iterating through the pages which have mapped buffer_heads, we
failed to update the b_state value. This results in allocating blocks
at logical offset 0.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
If the filesystem has errors, ext4_da_writepages() will return a *lot*
of errors, including lots and lots of stack dumps. While it's true
that we are dropping user data on the floor, which is unfortunate, the
stack dumps aren't helpful, and they tend to obscure the true original
root cause of the problem. So in the case where the filesystem has
aborted, return an EROFS right away.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The convenience function do_blk_alloc() is a static function with only
one caller, so fold it into ext4_new_meta_blocks() to simplify the
code and to make it easier to understand.
To save more stack space, if count is a null pointer in
ext4_new_meta_blocks() assume that caller wanted a single block (and
if there is an error, no blocks were allocated).
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There were only two one callers of the function ext4_new_meta_block(),
which just a very simpler wrapper function around
ext4_new_meta_blocks(). Change those two functions to call
ext4_new_meta_blocks() directly, to save code and stack space usage.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
