qcs404 has 10 sensors connected to the single TSENS IP. Define a thermal
zone for each of those sensors to expose the temperature of each zone.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
qcs404 has a single TSENS IP block with 10 sensors. The calibration data
is stored in an eeprom (qfprom) that is accessed through the nvmem
framework. We add the qfprom node to allow the tsens sensors to be
calibrated correctly.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Support gfxclk dpm disablement.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
only printf smu version when if version not matched.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
the navi asic can't get current rpm by MSG_GetCurrentRpm,
it will cause show fan rpm error, use Metrics_t to replace it.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The AVI infoframe is incorrectly programmed on DCN1/2 when enabling a
stream - causing the wrong pixel encoding to be used for display.
This is because the AVI infoframe is programmed before the DIG BE is
connected to the FE and turned on, so enabling the AFMT block doesn't
actually work and the registers subsequently can't be written to.
[How]
Program the infoframe *after* turning on the DIG FE. This was the
behavior previously used but it was incorrectly reverted
when adding the DCN2 HW sequencer code.
v2: Don't call update_info_frame twice
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The mutex for procting SMU during hw_init was removed as system
will be deadlock when smu_populate_umd_state_clk try get SMU mutex.
Therefore need remove the residual mutex from failed path.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/sdma_v4_0.c:1167 sdma_v4_0_start() error: uninitialized symbol 'r'.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Inconsistent indentation and mixed use of brackets.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by smatch:
amdgpu_dm.c:5637 amdgpu_dm_commit_planes() error: we previously assumed 'acrtc_state->stream' could be null
This seems to be checked for null pretty consistently elsewhere.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/amdgpu_pm.c:1496 amdgpu_hwmon_show_temp() error: uninitialized symbol 'temp'.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/amdgpu_pm.c:693 amdgpu_set_pp_od_clk_voltage() error: uninitialized symbol 'ret'.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/soc15.c:715 soc15_get_pcie_usage() warn: inconsistent indenting
And a similar one in si.c.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to protect the comments. The DCN1_01 config
was dopped anyway. Got accidently brought back with the
navi merge.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DM verity should also use DMERR_LIMIT to limit repeat data block
corruption messages.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For the first call to realloc_argv() in dm_split_args(), old_argv is
NULL and size is zero. Then memcpy is called, with the NULL old_argv
as the source argument and a zero size argument. AFAIK, this is
undefined behavior and generates the following warning when compiled
with UBSAN on ppc64le:
In file included from ./arch/powerpc/include/asm/paca.h:19,
from ./arch/powerpc/include/asm/current.h:16,
from ./include/linux/sched.h:12,
from ./include/linux/kthread.h:6,
from drivers/md/dm-core.h:12,
from drivers/md/dm-table.c:8:
In function 'memcpy',
inlined from 'realloc_argv' at drivers/md/dm-table.c:565:3,
inlined from 'dm_split_args' at drivers/md/dm-table.c:588:9:
./include/linux/string.h:345:9: error: argument 2 null where non-null expected [-Werror=nonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/md/dm-table.c: In function 'dm_split_args':
./include/linux/string.h:345:9: note: in a call to built-in function '__builtin_memcpy'
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Currently, although we submit super bios in order (and super.nr_entries
is incremented by each logged entry), submit_bio() is async so each
super sector may not be written to log device in order and then the
final nr_entries may be smaller than it should be.
This problem can be reproduced by the xfstests generic/455 with ext4:
QA output created by 455
-Silence is golden
+mark 'end' does not exist
Fix this by serializing submission of super sectors to make sure each
is written to the log disk in order.
Fixes: 0e9cebe724 ("dm: add log writes target")
Cc: stable@vger.kernel.org
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Suggested-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tegra's timer has 29 bits for the counter and for the "load" register
which sets counter to a load-value. The counter's value is lower than
the actual value by 1 because it starts to decrement after one tick,
hence the maximum number of ticks that hardware can handle equals to
29 bits + 1.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tegra's timer uses n+1 scheme for the counter, i.e. timer will fire after
one tick if 0 is loaded. The minimum and maximum numbers of oneshot ticks
are defined by clockevents_config_and_register(min, max) invocation and
the min value is set to 1 tick. Hence "cycles" value can't ever be 0,
unless it's a bug in clocksource core.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We're adjusting the timer's base for each per-CPU timer to point to the
actual start of the timer since device-tree defines a compound registers
range that includes all of the timers. In this case the original base
need to be restore before calling iounmap to unmap the proper address.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Convert all 1MHz literals to a verbose constant for better readability.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
There is no need to cast void because kernel allows to do that without
a warning message from a compiler.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The of_clk structure has a period field that is set up initially by
timer_of_clk_init(), that period value need to be adjusted for a case of
TIMER1-9 that are running at a fixed rate that doesn't match the clock's
rate. Note that the period value is currently used only by some of the
clocksource drivers internally and hence this is just a minor cleanup
change that doesn't fix anything.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It was left unnoticed by accident, which means that the code could be
cleaned up a tad more.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The clocksource rate is initialized only for the first per-CPU clocksource
and then that rate shall be replicated for the rest of clocksource's
because they are initialized manually in the code.
Fixes: 3be2a85a0b61 ("clocksource/drivers/tegra: Support per-CPU timers on all Tegra's")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Different mechanisms are used to test and set elf_hwcaps between ARM
and ARM64, this results in the use of ifdeferry in this file when
setting/testing for the EVTSTRM hwcap.
Let's improve readability by extracting this to an arch helper.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The system counter (sys_ctr) is a programmable system counter
which provides a shared time base to the Cortex A15, A7, A53 etc cores.
It is intended for use in applications where the counter is always
powered on and supports multiple, unrelated clocks. The sys_ctr hardware
supports:
- 56-bit counter width (roll-over time greater than 40 years)
- compare frame(64-bit compare value) contains programmable interrupt
generation when compare value <= counter value.
[dlezcano] Fixed over 80 chars length warning
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Rename driver's source file to better reflect that it's not specific to
older SoC generations.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Arch-timer is more preferable for a range of Tegra SoC generations as
it has higher precision and is not affect by any kind of problems.
Pointed-out-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove build dependency on ARM for compile-testing to allow non-arch
specific build-bots (like Intel's test robot) to compile the driver and
report about problems.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Correct typo and use proper upper casing for acronyms in the comments,
use common style for error messages, prepend error messages with
"tegra-timer:", add error message for cpuhp_setup_state() failure and
clean up whitespaces in the code to fix checkpatch warnings.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Release all requested IRQ's on the request error to properly clean up
allocated resources.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The readl/writel functions are inserting memory barrier to ensure that
outstanding memory writes are completed, this results in L2 cache syncing
being done on Tegra20 and Tegra30 which isn't a very cheap operation.
Replace all readl/writel occurrences in the code with the relaxed versions
since there is no need for the memory-access syncing.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reset timer's hardware state to ensure that initially it is in a
predictable state.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tegra132 is 64bit platform and it has the tegra20-timer hardware unit.
Right now the corresponding timer code isn't compiled for ARM64, remove
ifdef'iness from the code and compile tegra20-timer for both 32 and 64 bit
platforms. Also note that like the older generations, Tegra210 has the
microseconds counter, hence the timer_us clocksource is now made available
for Tegra210 as well.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Assign TMR1-4 per-CPU core on 32bit Tegra's in a way it is done for
Tegra210. In a result each core can handle its own timer events, less
code is unique to ARM64 and Tegra's clock events driver now has higher
rating on all Tegra's, replacing the ARM's TWD timer which isn't very
accurate due to the clock rate jitter caused by CPU frequency scaling.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Exynos SoCs based on CA7/CA15 have 2 timer interfaces: custom Exynos MCT
(Multi Core Timer) and standard ARM Architected Timers.
There are use cases, where both timer interfaces are used simultanously.
One of such examples is using Exynos MCT for the main system timer and
ARM Architected Timers for the KVM and virtualized guests (KVM requires
arch timers).
Exynos Multi-Core Timer driver (exynos_mct) must be however started
before ARM Architected Timers (arch_timer), because they both share some
common hardware blocks (global system counter) and turning on MCT is
needed to get ARM Architected Timer working properly.
To ensure selecting Exynos MCT as the main system timer, increase MCT
timer rating. To ensure proper starting order of both timers during
suspend/resume cycle, increase MCT hotplug priority over ARM Archictected
Timers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This is in-kernel C code, so there is no reason to use _BITUL().
Replace it with equivalent BIT().
I added #include <linux/bits.h> explicitly although it has been included
by other headers eventually.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds delay timer functionality to the IXP4xx
timer driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Comply with the licensing rules defined in the documentation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch removes the hns-roce.ko for cleanup all the exported symbols in
common part.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
These printing macros already add a trailing newline, so having another
one here just makes for blank lines when these prints are enabled.
Remove these needless newlines.
Fixes: 6bbc923dfc ("dm: add support to directly boot to a mapped device")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
By mistake, there is a '&' instead of a '==' in the definition of the
macro BFQQ_TOTALLY_SEEKY. This commit replaces the wrong operator with
the correct one.
Fixes: 7074f076ff ("block, bfq: do not tag totally seeky queues as soft rt")
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix 2 kstrndup() calls with incorrect argument order.
Fixes: 6bbc923dfc ("dm: add support to directly boot to a mapped device")
Cc: stable@vger.kernel.org # v5.1
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We may need to sleep for up to 80ms
(8ms per each of up to 10 loop iterations):
/* First DPCD read after VDD ON can fail if the particular board
* does not have HPD pin wired correctly. So if DPCD read fails,
* which it should never happen, retry a few times. Target worst
* case scenario of 80 ms.
*/
Switch udelay to msleep to avoid limits on arm.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ULL is needed for 32 bit arches.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only user was the prime import, and drm_prime.c takes care of that
now.
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Russell King <linux+etnaviv@armlinux.org.uk>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: etnaviv@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190614203615.12639-43-daniel.vetter@ffwll.ch
Greg is busy already, but maybe he won't do everything ...
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190614203615.12639-59-daniel.vetter@ffwll.ch
