Adds a flush of RX and TX FIFOs, and fixes some errors:
- adds RX FIFO flush in startup fonction
- removes the useless transmitter enabling in startup fonction
(e.g. receiver only, see Documentation/serial/driver)
- configures FIFO threshold before enabling it, rather than after
- flushes both TX and RX in set_termios function
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of RX FIFO threshold in order to improve the RX FIFO
management.
This is done by enabling fifo threshold interrupt, instead of relying
on rx empty/fifo not full irq. That basically generates one irq/char
currently. With this patch:
- RXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/RXCFG, e.g. 1 over 8 with current
RXCFG setting.
- Receiver timeout is used to gather chars when FIFO threshold isn't
reached.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of TX FIFO threshold in order to improve the TX FIFO
management:
- TX FIFO threshold irq enabling (instead of relying on tx empty / fifo
not full irq that generates one irq/char)
- TXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/TXCFG, e.g. 1 over 8 with current
TXCFG setting.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improves PIO transmission:
- Replaces the FIFO filling per character by a filling per blocks of
characters, which provides better performances
- Replaces the active waiting loop by TX empty interrupt dynamic handling.
TXE interrupt is now enabled when data has to be sent (ie when
uart_circ is not empty), and inhibited when there is no more data to
send (ie when uart_circ is empty).
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of RX timeout interrupts to limit the number of interrupts.
RX timeout is a number of bits (baud clock cycles) without
transmission seen in the receiver. One character is used as an arbitrary
RX timeout value.
If parity is enabled, the number of bits has to include parity bit.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds an example of how to inject errors into admin commands.
Suggested-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Minwoo Im <minwoo.im@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This enables to inject errors into the commands submitted to the admin
queue.
It is useful to test error handling in the controller initialization.
# echo 100 > /sys/kernel/debug/nvme0/fault_inject/probability
# echo 1 > /sys/kernel/debug/nvme0/fault_inject/times
# echo 10 > /sys/kernel/debug/nvme0/fault_inject/space
# nvme reset /dev/nvme0
# dmesg
...
nvme nvme0: Could not set queue count (16385)
nvme nvme0: IO queues not created
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currenlty fault injection support for nvme only enables to inject errors
into the commands submitted to I/O queues.
In preparation for fault injection into the admin commands, this makes
the helper functions independent of struct nvme_ns.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch introduces target-side request tracing. As Christoph
suggested, the trace would not be in a core or module to avoid
disadvantages like cache miss:
http://lists.infradead.org/pipermail/linux-nvme/2019-June/024721.html
The target-side trace code is entirely based on the Johannes's trace code
from the host side. It has lots of codes duplicated, but it would be
better than having advantages mentioned above.
It also traces not only fabrics commands, but also nvme normal commands.
Once the codes to be shared gets bigger, then we can make it common as
suggsted.
This also removed the create_sq and create_cq trace parsing functions
because it will be done by the connect fabrics command.
Example:
echo 1 > /sys/kernel/debug/tracing/event/nvmet/nvmet_req_init/enable
echo 1 > /sys/kernel/debug/tracing/event/nvmet/nvmet_req_complete/enable
cat /sys/kernel/debug/tracing/trace
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[hch: fixed the symbol namespace and a an endianess conversion]
Signed-off-by: Christoph Hellwig <hch@lst.de>
With gcc 4.1:
drivers/lightnvm/core.c: In function ‘nvm_remove_tgt’:
drivers/lightnvm/core.c:510: warning: ‘t’ is used uninitialized in this function
Indeed, if no NVM devices have been registered, t will be an
uninitialized pointer, and may be dereferenced later. A call to
nvm_remove_tgt() can be triggered from userspace by issuing the
NVM_DEV_REMOVE ioctl on the lightnvm control device.
Fix this by preinitializing t to NULL.
Fixes: 843f2edbdd ("lightnvm: do not remove instance under global lock")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_add_pc_page() may merge pages when a bio is padded due to a flush.
Fix iteration over the bio to free the correct pages in case of a merge.
Signed-off-by: Heiner Litz <hlitz@ucsc.edu>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The "result" field is in 64bit to be printed out which means it could be
like:
nvme_complete_rq: nvme0: qid=0, cmdid=0, res=18446612684158962624, etries=0, flags=0x0, status=0
Switch both the result and status field to be printed in hexadecimal
format to be easier to read.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch introduces fabrics commands tracing feature from host-side.
This patch does not include any changes for the previous host-side
tracing, but just add fabrics commands parsing in cmd=() format.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[hch: fixed some whitespace damage]
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patches are going to provide the target-side trace which
might need these kind of macros. It would be great if it can be shared
between host and target side both.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme_trace_disk_name() is now already being invoked with the function
prototype in trace.h. We don't need to export this symbol at all.
The following patches are going to provide target-side trace feature
with the exactly same function with this so that this patch removes the
EXPORT_SYMBOL() for this function.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The call to kick_siblings() dereferences the rq->context, so we should
not drop our local reference until afterwards!
v2: Stick to setting ce.inflight=NULL before kicking as this is what the
other threads will check to see if the context is ready for takeover.
Fixes: 22b7a426bb ("drm/i915/execlists: Preempt-to-busy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190621080729.2652-1-chris@chris-wilson.co.uk
Remove the status parameter o nvme_remove_dead_ctrl(), which is only
used for printing it.
We move the print message to the same function where actual error is
occurring.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the state change to NVME_CTRL_CONNECTING fails, the dmesg is going to
be like:
[ 293.689160] nvme nvme0: failed to mark controller CONNECTING
[ 293.689160] nvme nvme0: Removing after probe failure status: 0
Even it prints the first line to indicate the situation, the second line
is not proper because the status is 0 which means normally success of
the previous operation.
This patch makes it indicate the proper error value when it fails.
[ 25.932367] nvme nvme0: failed to mark controller CONNECTING
[ 25.932369] nvme nvme0: Removing after probe failure status: -16
This situation is able to be easily reproduced by:
root@target:~# rmmod nvme && modprobe nvme && rmmod nvme
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch removes the confusing assignment of the variable result at
the time of declaration and sets the value in error cases next to the
places where the actual error is happening.
Here we also set the result value to -ENODEV when we fail at the final
ctrl state transition in nvme_reset_work(). Without this assignment
result will hold 0 from nvme_setup_io_queue() and on failure 0 will be
passed to he nvme_remove_dead_ctrl() from final state transition.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
queue_count_set() seems like that it has been provided to limit the
number of queue entries for write/poll queues. But, the
queue_count_set() has been doing nothing but a parameter check even it
has num_possible_cpus() which is nop.
This patch removes entire queue_count_ops from the write_queues and
poll_queues.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
poll_queues will be zero even without zero initialization here.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The nvme pci driver prepares its devices for power loss during suspend
by shutting down the controllers. The power setting is deferred to
pci driver's power management before the platform removes power. The
suspend-to-idle mode, however, does not remove power.
NVMe devices that implement host managed power settings can achieve
lower power and better transition latencies than using generic PCI power
settings. Try to use this feature if the platform is not involved with
the suspend. If successful, restore the previous power state on resume.
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
[hch: fixed the compilation for the !CONFIG_PM_SLEEP case]
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch introduces a nvme_is_fabrics() inline function to check
whether or not the given command structure is for fabrics.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Future use intends to make use of both, so export these functions. And
since their implementation is identical except for the opcode, provide a
new function that implement both.
[akinobu.mita@gmail.com>: fix line over 80 characters]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a shared namespace is removed, we call blk_cleanup_queue()
when the device can still be accessed as the current path and this can
result in submission to a dying queue. Hence, direct_make_request()
called by our mpath device may fail (propagating the failure to userspace).
Instead, we want to failover this I/O to a different path if one exists.
Thus, before we cleanup the request queue, we make sure that the device is
cleared from the current path nor it can be selected again as such.
Fix this by:
- clear the ns from the head->list and synchronize rcu to make sure there is
no concurrent path search that restores it as the current path
- clear the mpath current path in order to trigger a subsequent path search
and sync srcu to wait for any ongoing request submissions
- safely continue to namespace removal and blk_cleanup_queue
Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When looking at console messages to troubleshoot, there are one
maybe two messages before creation of the controller is complete.
However, a lot of io takes place to reach that point. It's unclear
when things have started.
Add a message when the controller is attempting to create a new
association. Thus we know what controller, between what host and
remote port, and what NQN is being put into place for any
subsequent success or failure messages.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
To support scenarios which aren't bound to nvmetcli add port scenarios,
which is currently where the nvmet_fc transport invokes the discovery
event callbacks, a syfs attribute is added to lpfc which can be written
to cause an RSCN to be generated for the nport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch updates RSCN receive processing to check for the remote
port being an NVME port, and if so, invoke the nvme_fc callback to
rescan the remote port. The rescan will generate a discovery udev
event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for the nvmet discovery op. When the callback
routine is called, the driver will call the routine to generate an RSCN
to the port on the other end of the link.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds general RSCN support:
- The ability to transmit an RSCN to the port on the other end of
the link (regular port if pt2pt, or fabric controller if fabric).
- And general recognition of an RSCN ELS when an ELS is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update fcloop to support the discovery_event operation and
invoke a nvme rescan. In a real fc adapter, this would generate an
RSCN, which the host would receive and convert into a nvme rescan
on the remote port specified in the rscn payload.
Signed-off-by: James Smart <jsmart2021@gmail.com>
[kbuild-bot: fcloop_tgt_discovery_evt can be static]
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for the nvmet discovery_change transport op.
In turn, the transport adds it's own LLDD api callback discovery_event
op to request the LLDD to generate an RSCN for the discovery change.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some transports, such as FC-NVME, support discovery controller change
events without the use of a persistent discovery controller. FC receives
events via RSCN from the FC Fabric Controller or subsystem FC port.
This patch adds a nvmet transport op that is called whenever a
discovery change event occurs in the nvmet layer.
To facilitate the callback without adding another layer to cross into
core.c to reference the transport ops, the port structure snapshots
the transport ops when the port is enabled and clears them when disabled.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This reverts commit 2e9fe53910.
Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.
Signed-off-by: Oliver Barta <o.barta89@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 2e9fe53910 ("serial: 8250: Don't service RX FIFO if interrupts are disabled")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bfq schedule now uses css_next_descendant_pre directly after
the stats functionality depending on it has been from the core
blk-cgroup code to bfq. Export the symbol so that bfq can still
be build modular.
Fixes: d6258980da ("bfq-iosched: move bfq_stat_recursive_sum into the only caller")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.
Use MSR / MCR <-> TIOCM wrapper functions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a check for the GPIOs property existence, before the
GPIO is requested. This fixes an issue seen when the 8250 mctrl_gpio
support is added (2nd patch in this patch series) on x86 platforms using
ACPI.
Here Mika's comments from 2016-08-09:
"
I noticed that with v4.8-rc1 serial console of some of our Broxton
systems does not work properly anymore. I'm able to see output but input
does not work.
I bisected it down to commit 4ef03d3287
("tty/serial/8250: use mctrl_gpio helpers").
The reason why it fails is that in ACPI we do not have names for GPIOs
(except when _DSD is used) so we use the "idx" to index into _CRS GPIO
resources. Now mctrl_gpio_init_noauto() goes through a list of GPIOs
calling devm_gpiod_get_index_optional() passing "idx" of 0 for each. The
UART device in Broxton has following (simplified) ACPI description:
Device (URT4)
{
...
Name (_CRS, ResourceTemplate () {
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003A
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003D
}
})
In this case it finds the first GPIO (0x003A which happens to be RX pin
for that UART), turns it into GPIO which then breaks input for the UART
device. This also breaks systems with bluetooth connected to UART (those
typically have some GPIOs in their _CRS).
Any ideas how to fix this?
We cannot just drop the _CRS index lookup fallback because that would
break many existing machines out there so maybe we can limit this to
only DT enabled machines. Or alternatively probe if the property first
exists before trying to acquire the GPIOs (using
device_property_present()).
"
This patch implements the fix suggested by Mika in his statement above.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that ARM errata 814220 is selected by STM32MP157 SoC
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The v7 ARM states that all cache and branch predictor maintenance operations
that do not specify an address execute, relative to each other, in program
order. However, because of this erratum, an L2 set/way cache maintenance
operation can overtake an L1 set/way cache maintenance operation, this would
cause the data corruption.
This ERRATA affected the Cortex-A7 and present in r0p2, r0p3, r0p4, r0p5.
This patch is the SW workaround by adding a DSB before changing cache levels as
the ARM ERRATA: ARM/MP: 814220 told in the ARM ERRATA documentation.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The Allwinner SoCs have a PWM controller supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add CMT0 and CMT1 to the R-Car Gen2 V2H (r8a7792) SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 9eb36b945b ("ARM: dts: iwg23s-sbc: Add uSD and eMMC support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 029efb3a03 ("ARM: dts: iwg20d-q7: Add SDHI1 support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for input switch SW3 on the Renesas RZ/A2M EVB
development board.
Note that this uses the IRQ interrupt, as the RZ/A2 GPIO controller
does not include interrupt support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the IRQC on RZ/A2M, which is a small front-end to the
GIC. This allows to use up to 8 external interrupts with configurable
sense select.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch sorts the nodes of arch/arm/boot/dts/r7s9210-rza2mevb.dts.
* Sort subnodes of root ("/") node alphabetically
* Sort following top-level nodes alphabetically
* Sort subnodes of pinctrl alphabetically
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebase and sort new ehci nodes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull MD changes from Song.
* 'md-next' of https://github.com/liu-song-6/linux:
md: add bitmap_abort label in md_run
md-bitmap: create and destroy wb_info_pool with the change of bitmap
md-bitmap: create and destroy wb_info_pool with the change of backlog
md: introduce mddev_create/destroy_wb_pool for the change of member device
md/raid1: fix potential data inconsistency issue with write behind device
