Always set DMA masks in ide_pci_setup_ports() to make sure that the valid
masks for a host are set.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays IDE core always provides drive ID and ide-disk always setups
drive->capacity64 so this quirk is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't override the cable type if the "idex=ata66" parameter was used.
While at it:
* atiixp.c: factor out cable detection to atiixp_cable_detect() from
init_hwif_atiixp().
* cs5535.c: pass 'ide_hwif_t *hwif' instead of 'struct pci_dev *dev' to
cs5535_cable_detect().
* scc_pata.c: factor out cable detection to scc_cable_detect() from
init_hwif_scc() and remove incorrect comment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The host driver must set hwif's ->no_io_32bit setting not drive's one
(ide_port_tune_devices() overrides drive's setting).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On DTC2278 32-bit I/O has to be enabled for both devices on the port
so always enable it during init time and disallow further changes.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
sg_dma_len(sg) is invalid before the s/g list is DMA-mapped.
This fixes a post 2.6.24 regression which prevents access to SBP-2
devices on several architectures, introduced by "ieee1394: sbp2: s/g
list access cosmetics", commit 825f1df545.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
- Buttons on the BF533-STAMP board are not inverted
- Fix spurious GPIO Interrupt caused during set irq_type for edge triggered interrupts
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The definitions of the line discipline numbers N_* have been moved
from asm-*/termios.h to linux/tty.h, but the Blackfin architecture
has somehow evaded that move. Bring it in line with the others.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Move the init sections to the end of memory so that after they
are free, run time memory is all continugous - this should help decrease
memory fragementation.
When doing this, we also pack some of the other sections a little closer
together, to make sure we don't waste memory. To make this happen,
we need to rename the .data.init_task section to .init_task.data, so
it doesn't get picked up by the linker script glob.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
To save/restore the trace buffer control so that if we take an exception
after turning off the trace buffer at a higher level we dont inadvertently
turn the trace buffer back on
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
According to ACPI spec, the _TSD object provides T-state control cross
logical processor dependency information to OSPM. So the t-state
coordination should be considered when T-state for one cpu is changed.
According to ACPI spec, three types of coordination are defined.
SW_ALL, SW_ANY and HW_ALL.
SW_ALL: it means that OSPM needs to initiate T-state transition on
all processors in the domain. It is necessary to call throttling set function
for all affected cpus.
SW_ANY: it means that OSPM may initiate T-state transition on any processor in
the domain.
HW_ALL: Spec only says that hardware will perform the coordination and doesn't
recommend how OSPM coordinate T-state among the affected cpus. So it is treated
as the type of SW_ALL. It means that OSPM needs to initiate t-state transition
on all the processors in the domain.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The t-state coordination should be considered when T-state for one cpu
is changed.It means that OSPM should select one proper target T-state for
the all affected cpus before updating T-state.
So the function of acpi_processor_throttling_notifier is added.
Before updating T-state it can be called for all the affected cpus to get
the proper target T-state, which can meet the requirement of thermal, user and
_TPC. After updating T-state, it can be called to update T-state flag.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Accordint to ACPI spec, the _TSD object provides T-state control cross
logical processor dependency information to OSPM.
After the _TSD data for all cpus are obtained, OSPM will set up
the T-state coordination between CPUs.
Of course if the _TSD doesn't exist or _TSD data is incorrect , it is
assumed that there is no T-state coordination and T-state is changed
independently.
Now there is no proper solution to update T-state coordination after
one cpu is hotplugged. So this patch won't support hotplugged cpu very well.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It is necessary to check the parameter when calling the function of
acpi_processor_get/set_throttling function so as to avoid the NULL
pointer reference in pr or throttling.
http://bugzilla.kernel.org/show_bug.cgi?id=9747
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI_PDC_SMP_T_SWCOORD bit is set by and OS that is capable of
native ACPI throttling software coordination for mutli-processors
using the _TSD information.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Vendors often ship machines with a choice of integrated or discrete
graphics, and use the same DSDT for both. As a result, the ACPI video
module will locate devices that may not exist on this specific platform.
Attempt to determine whether the device exists or not, and abort the
device creation if it doesn't.
http://bugzilla.kernel.org/show_bug.cgi?id=9614
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a bug (zero pointer access) only seen on BF561, during USB
Mass Storage/SCSI Host initialization.
It appears to be related to registering a none existing CPU
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- Add support for irq_wake on system and gpio interrupts
- Remove outdated kernel options
- Add option to select default PM mode
- Fix various places where SIC_IWRx was only handled partially
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Merge single core ints-priority-sc.c and dual core ints-priority-dc.c
into one common code ints-priority.c
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The alias name may be used in _PSL, _ALx and _TZD,
so we bind the cooling device only if the acpi_device node matches.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel menlow platform specific driver for thermal management extension.
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix an imprecision in CELSIUS_TO_KELVIN and move these
two macroes to a proper place.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel menlow driver needs to get the pointer of themal_zone_device
structure of an ACPI thermal zone.
Attach this to each ACPI thermal zone device object.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Register ACPI video device as thermal cooling devices as they may be listed
in _TZD method and the backlight control can be used for throttling.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Register ACPI processor as thermal cooling devices.
A combination of processor T-state and P-state are used for thermal throttling.
the processor will reduce the frequency first and then set the T-state.
we use cpufreq_thermal_reduction_pctg to calculate the cpufreq limit,
and call cpufreq_verify_with_limit to set the cpufreq limit.
if cpufreq driver is loaded, then we have four cooling state for cpufreq control.
cooling state 0: cpufreq limit == max_freq
cooling state 1: cpufreq limit == max_freq * 80%
cooling state 2: cpufreq limit == max_freq * 60%
cooling state 3: cpufreq limit == max_freq * 40%
after the cpufreq limit is set to 40 percentage of the max_freq,
we use T-state for cooling.
eg. a processor has P-state support, and it has 8 T-state (T0-T7),
the max_state of the proceesor is 10:
state cpufreq-limit T-state
0: max_freq T0
1: max_freq * 80% T0
2: max_freq * 60% T0
3: max_freq * 40% T0
4: max_freq * 40% T1
5: max_freq * 40% T2
6: max_freq * 40% T3
7: max_freq * 40% T4
8: max_freq * 40% T5
9: max_freq * 40% T6
10: max_freq * 40% T7
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Register ACPI Fan as thermal cooling device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
Change the ACPI thermal action upon notification 0x81 and 0x82.
According to the ACPI spec, we should:
re-evaluate _PSV and _ACx methods upon notification 0x81
re-evaluate _PSL and _ALx and _TZD upon notificaiton 0x82.
But the current code re-evaluates all the trip points for 0x81 while
only re-evaluates _TZD for 0x82.
Fix this violation of ACPI spec.
TODO: devices in _PSL, _ALx and _TZD may change after a notification 0x82.
At this time, we need to re-bind the cooling devices with the thermal zone.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Register ACPI thermal zone as thermal zone device.
the new sys I/F for ACPI thermal zone will be like this:
/sys/class/thermal:
|thermal_zone1:
|-----type: "ACPI thermal zone". RO
|-----temp: the current temperature. RO
|-----mode: the current working mode. RW.
the default value is "kernel" which means thermal
management is done by ACPI thermal driver.
"echo user > mode" prevents all the ACPI thermal driver
actions upon any trip points.
|-----trip_point_0_temp: the threshold of trip point 0. RO.
|-----trip_point_0_type: "critical". RO.
the type of trip point 0
This may be one of critical/hot/passive/active[x]
for an ACPI thermal zone.
...
|-----trip_point_3_temp:
|-----trip_point_3_type: "active[1]"
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Generic Thermal sysfs driver for thermal management.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The sysfs backlight class provides no mechanism for querying the
acceptable brightness for a backlight. The ACPI spec states that values
are only valid if they are reported as available by the firmware. Since
we can't provide that information to userspace, instead collapse the
range to the number of actual values that can be set.
http://bugzilla.kernel.org/show_bug.cgi?id=9277
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://linux-nfs.org/~bfields/linux: (100 commits)
SUNRPC: RPC program information is stored in unsigned integers
SUNRPC: Move exported symbol definitions after function declaration part 2
NLM: tear down RPC clients in nlm_shutdown_hosts
SUNRPC: spin svc_rqst initialization to its own function
nfsd: more careful input validation in nfsctl write methods
lockd: minor log message fix
knfsd: don't bother mapping putrootfh enoent to eperm
rdma: makefile
rdma: ONCRPC RDMA protocol marshalling
rdma: SVCRDMA sendto
rdma: SVCRDMA recvfrom
rdma: SVCRDMA Core Transport Services
rdma: SVCRDMA Transport Module
rdma: SVCRMDA Header File
svc: Add svc_xprt_names service to replace svc_sock_names
knfsd: Support adding transports by writing portlist file
svc: Add svc API that queries for a transport instance
svc: Add /proc/sys/sunrpc/transport files
svc: Add transport hdr size for defer/revisit
svc: Move the xprt independent code to the svc_xprt.c file
...
