In pcibios_fixup_bus(), bridges that are subordinate
to transparent bridges were still relocating their
IORESOURCE_IO and IO_RESOURCE_MEM start and end values.
Fix this by preventing the transparent bridge from
relocating the start and end values, thus allowing the
subordinate non-transparent bridge full molestation rights.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set IDE in ULI1575 to not 100% native mode, which forces
the IDE driver to probe the irq itself.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI-e controllers have an issue in that they use the
PCI_PRIMARY_BUS register in the virtual P2P bridge to determine which
bus number to match on when generating a type 0 config cycle. The
issue is if we are renumbering bus numbers to match Linux we will try
setting the PCI_PRIMARY_BUS and will not know which bus number to use
for generating type 0 config cycles. We surpress writing the register
in the P2P bridge and always keep it at zero.
In the future when proper PCI domain support is working we should be
able to remove this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We check the Link Training and State Status register to make sure we
are at least at the L0 state.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The generic PCI config ops indirect support for ppc32 covers only two
cases (implicit vs explicit) type 0/1 config cycles via set_cfg_type.
Added a indirect_type bit mask to handle other variants.
Added support for PCI-e extended registers and moved the cfg_type
handling into the bit mask for ARCH=powerpc. We can also use this to
handle indirect quirks.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds device nodes for the PCI bridges as well as the ISA devices on
the newer revision MPC8641HPCN. It also adds the PCI ranges to the soc
node so that address translation for the ISA devices works properly.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove errata for PCI-e support of Rev 1.0 of MPC8641 since its considered
obselete and is not production level silicon from Freescale.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.
83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added self_busno to pci_controller and indirect PCI ops to be set by
board code to indicate which bus number to use when talking to the PHB.
By default we use zero since the majority of controllers that have
implicit mechanisms to talk to the PHBs use a bus number of zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The user of the fsl_pcie code doesn't set bus_offset and 82xx doesn't
require it either. Remove the places in the code that reference it so
we can remove it all together.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have the pci_controller in the exclude function we can easy
figure out if the bus number is the PHB or not. The old style of using a
variable setup at init time was actually broken and would only work in
specific cases.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The hose->bus_offset is only used for PCI config cycles and the 52xx PCI
config code doesn't actually ever set bus_offset to a non-zero value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale and Marvell PCI controllers dont require explicit setting for
type 1 config cycles. They handle producing them by implicitly looking at the
bus, devfn.
The TSI108 and 52xx don't use the generic PCI indirect code and thus don't
bother with set_cfg_type.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The TSI108 code and the 32 bit powermac and chrp platforms
have dependency on PCI that is not easy or desirable to get rid
of.
The easiest fix is to always select CONFIG_PCI if one of those
platforms is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When CONFIG_PCI is disabled, the definitions for isa_io_base,
isa_mem_base and pci_dram_offset are entirely unused, but they
can result in link failure because they are defined in multiple
places.
The easiest fix is to just remove all these definitions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cores used in the MPC82xx/83xx/86xx embedded controllers are very similar
to those in the 32 bit general-purpose processors, so it makes sense to
treat them as the same CPU family.
Choosing between the embedded platforms and the multiplatform code is
now done in the platform menu, but functionally everything stays the
same.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix printk format warning:
drivers/net/irda/irport.c:512: warning: format '%d' expects type 'int', but argument 5 has type 'long int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4bedb45203 both the udp and tcp
cases where changed to use udp_hdr() instead of leaving the tcp case
alone and fixing with tcp_hdr().
This ended up causing random behavior with TCP connections because
of looking for tcp_hdr()->check in the wrong place.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
#1
Until kernel ver. 2.6.21 (including) cancel_rearming_delayed_work()
required a work function should always (unconditionally) rearm with
delay > 0 - otherwise it would endlessly loop. This patch replaces
this function with cancel_delayed_work(). Later kernel versions don't
require this, so here it's only for uniformity.
#2
After deleting a timer in cancel_[rearming_]delayed_work() there could
stay a last skb queued in npinfo->txq causing a memory leak after
kfree(npinfo).
Initial patch & testing by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many laptops have rf-kill physical switches that are not keys, but slider
or rocker switches. Often (like in all ThinkPads with a radio kill slider
switch), they have both a slider/rocker switch and a hot key.
Trying to kludge a real switch to act like a key is not a very smart thing
to do if you can help it, and it gets specially bad when you are going to
have both in the same machine. So, we do the right thing and add an input
EV_SW event for radio kill switches.
The EV_SW SW_RADIO event is defined with positive logic, i.e. when the
switch is active, the radios are to be enabled. When the switch is
inactive, the radios are to be disabled.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to take serio->drv_mutex in serio_cleanup() to prevent the
function from being called while driver is in the middle of attaching
to a serio port. Such situation can happen with i8042 and atkbd drivers
if user rapidly presses Ctrl-Alt-Del during system startup, and leads
to kernel oops.
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As seen on sparc64-allnoconfig:
CC arch/sparc64/mm/tlb.o
In file included from arch/sparc64/mm/tlb.c:19:
include/asm/tlb.h: In function 'tlb_flush_mmu':
include/asm/tlb.h:60: warning: implicit declaration of function 'release_pages'
include/asm/tlb.h: In function 'tlb_remove_page':
include/asm/tlb.h:92: warning: implicit declaration of function 'page_cache_release'
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
- make 2 needlessly global functions static
- remove the unused nettel_eraseconfig()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use NULL instead of 0 for pointer:
drivers/mtd/chips/cfi_cmdset_0001.c:2258:43: warning: Using plain integer as NULL pointer
Other changes by inspection.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The MTD DataFlash driver uses a semaphore as mutex. Use the mutex API instead
of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Update chip ID tables in m25p80 to handle more SPI flash chips, matching
datasheets. All of these can use the same core operations and are newer
chips that support the JEDEC "read id" instruction:
- Atmel AT25 and AT26 (seven chips)
- Spansion S25SL (five chips)
- SST 25VF (four chips)
- ST M25, M45 (five more chips)
- Winbond W25X series (seven chips)
That JEDEC instruction is now used, either to support a sanity check on the
platform data holding board configuration data, or to determine chip type
when it's not included in platform data. In fact, boards that don't need a
standard partition table may not need that platform data any more.
For chips that support 4KiB erase units, use that smaller block size instead
of the larger size (usually 64KiB); it's less wasteful. (Tested on W25X80.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Convert semaphore usage in m25p80 driver to mutex; mention another kind of
SPI flash chip that should be able to use this driver (given minor tweaks).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds 405 platform support to the 440 NDFC driver. The new
AMCC 405EZ PPC is equipped with the same NDFC core as the 440EP(x)
and other will follow soon.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix the sparse warnings generated by the implicit
dependency of mtd_blkdevs.c and mtd_core.c for the
two symbols mtd_table and mtd_table_mutex. This is
done by adding an local header file mtdcore.h to
define these (including the warning about the
non-proliferation of these symbols).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix sparse warnings generated from cfi_cmdset_0001.c.
drivers/mtd/chips/cfi_cmdset_0001.c:1783:5: warning: symbol 'cfi_intelext_erase_varsize' was not declared. Should it be static?
drivers/mtd/chips/cfi_cmdset_0001.c:2258:43: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make cfi_amdstd_erase_varsize static, as declared at the top
of the file to ensure sparse does not print a warning for an
undeclared function, as so:
drivers/mtd/chips/cfi_cmdset_0002.c:1612:5: warning: symbol 'cfi_amdstd_erase_varsize' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The mtd_blktrans_ops is not defined in any of the headers
and is indeed not used elsewhere in the kernel, so mark it
as static to reduce the warnings from sparse
drivers/mtd/mtd_blkdevs.c:204:32: warning: symbol 'mtd_blktrans_ops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The nand_base.c driver implicitly casts the uint32_t
eccpos array to 'int *', which is not only not guaranteed
to be the same sign as the source, but is not guaranteed
to be the same size.
Fix by changing nand_base.c to use uint32_t
referencing the eccpos fields.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Kernel oops and panic messages are invaluable when debugging crashes.
These messages often don't make it to flash based logging methods (say a
syslog on jffs2) due to the overheads involved in writing to flash.
This patch allows you to turn an MTD partition into a circular log
buffer where kernel oops and panic messages are written to. The messages
are obtained by registering a console driver and checking
oops_in_progress. Erases are performed in advance to maximise the
chances of a saving messages.
To activate it, add console=ttyMTDx to the kernel commandline (where x
is the mtd device number to use).
Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The try_to_freeze() call was in the wrong place; we need it in the
signal-pending loop now that a pending freeze also makes
signal_pending() return true.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We were checking the wrong (old) global variable to determine
whether to override server and force signing on the SMB
connection.
Acked-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Not all the world is an i386. Many architectures need 64-bit arguments to be
aligned in suitable pairs of registers, and the original
sys_sync_file_range(int, loff_t, loff_t, int) was therefore wasting an
argument register for padding after the first integer. Since we don't
normally have more than 6 arguments for system calls, that left no room for
the final argument on some architectures.
Fix this by introducing sys_sync_file_range2(int, int, loff_t, loff_t) which
all fits nicely. In fact, ARM already had that, but called it
sys_arm_sync_file_range. Move it to fs/sync.c and rename it, then implement
the needed compatibility routine. And stop the missing syscall check from
bitching about the absence of sys_sync_file_range() if we've implemented
sys_sync_file_range2() instead.
Tested on PPC32 and with 32-bit and 64-bit userspace on PPC64.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
