When disabling a sink the reference counter ensures the operation goes
through if nobody else is using it. As such if drvdata::mode is already
set do CS_MODE_DISABLED, it is an error and should be reported as such.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When operating in CPU-wide mode with an N:1 source/sink HW topology,
multiple CPUs can access a sink concurrently. As such reference counting
needs to happen when the device's spinlock is held to avoid racing with
other operations (start(), update(), stop()), such as:
session A Session B
----- -------
enable_sink
atomic_inc(refcount) = 1
...
atomic_dec(refcount) = 0 enable_sink
if (refcount == 0) disable_sink
atomic_inc()
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to handle device reference counting inside of the sink
drivers, add a return code to the sink::disable() operation so that
proper action can be taken if a sink has not been disabled.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure timestamps to be emitted at regular intervals in the trace
stream to temporally correlate instructions executed on different CPUs.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resource selector pair 0 is always implemented and reserved. As such
it should not be explicitly programmed.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the proper bit in the configuration register when contextID tracing
has been requested by user space. That way PE_CONTEXT elements are
generated by the tracers when a process is installed on a CPU.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add to the capabilities the ITRACE property so that ITRACE START events
are generated when the PMU is switched on by the core.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the power only if we were successful in probing the device.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the power handle only if we were successful. Otherwise
the AMBA bus code would do the rest.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the power only when we have successfully probed. Otherwise
leave it to the amba probe to do the rest.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Removed extra newline left after original modification]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We drop the power before we complete the probe successfully. We
are supposed to drop it only when we are successful. Also, probing
the etb_buffer_length happens with the power turned up. So we don't
need to do that again in the helper.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit c2c729415b ("coresight: platform: Cleanup coresight
connection handling"), we switched to re-using coresight_connections
for the coresight_device. However, that introduced a mismatch in the
alloc/free of the connections. The allocation is made using devm_*,
while we use kfree() to release the memory when a device is released
(even though we don't support this at the moment). Fix this by leaving
it to the automatic freeing of the memory.
Fixes: c2c729415b ("coresight: platform: Cleanup coresight connection handling")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge the drivers for the two varieties of replicators into
a singel one. The dynamic replicator has programming base
which can be programmed to filter the trace data. The driver
detects the type based on the "base" address value of the
device, which is NULL for the static device.
Also, while at it, remove the now obsolete DYNAMIC_REPLICATOR
config entry.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the dynamic replicator specific routines for merging with the
replicator driver. Also re-arrange the probe routine to make it easier
to merge.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a preparatory step to merge the separate drivers for static and
dynamic replicators, annotate the static replicator specific details.
Also refactor the probe routine to make it generic in order to merge
the drivers easily.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We fail to disable the clock in case of a failure during the
probe. Clean this up. Also, we are supposed to drop the pm reference
only when the probing is successful.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we failed to setup the DMA mask for TMC-ETR, report the
error before failing the probe.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warnings:
drivers/hwtracing/coresight/coresight-catu.c:488:35: warning:
symbol 'catu_helper_ops' was not declared. Should it be static?
drivers/hwtracing/coresight/coresight-catu.c:493:28: warning:
symbol 'catu_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang points out a syntax error, as the etr_catu_buf_ops structure is
declared 'static' before the type is known:
In file included from drivers/hwtracing/coresight/coresight-tmc-etr.c:12:
drivers/hwtracing/coresight/coresight-catu.h:116:40: warning: tentative definition of variable with internal linkage has incomplete non-array type 'const struct etr_buf_operations' [-Wtentative-definition-incomplete-type]
static const struct etr_buf_operations etr_catu_buf_ops;
^
drivers/hwtracing/coresight/coresight-catu.h:116:21: note: forward declaration of 'struct etr_buf_operations'
static const struct etr_buf_operations etr_catu_buf_ops;
This seems worth fixing in the code, so replace pointer to the empty
constant structure with a NULL pointer. We need an extra NULL pointer
check here, but the result should be better object code otherwise,
avoiding the silly empty structure.
Fixes: 434d611cdd ("coresight: catu: Plug in CATU as a backend for ETR buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Fixed line over 80 characters]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch fixes rts5260 power saving parameter
make power saving function work on L1.1, L1.2
Signed-off-by: RickyWu <ricky_wu@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace can make host function calls, called hgcm-calls through the
/dev/vboxguest device.
In this case we should not accept all hgcm-function-parameter-types, some
are only valid for in kernel calls.
This commit adds proper hgcm-function-parameter-type validation to the
ioctl for doing a hgcm-call from userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 376991db4b ("driver core: Postpone DMA tear-down until after
devres release"), we changed the ordering of tearing down the device DMA
ops and releasing all the device's resources; this was because the DMA ops
should be maintained until we release the device's managed DMA memories.
However, we have seen another crash on an arm64 system when a
device driver probe fails:
hisi_sas_v3_hw 0000:74:02.0: Adding to iommu group 2
scsi host1: hisi_sas_v3_hw
BUG: Bad page state in process swapper/0 pfn:313f5
page:ffff7e0000c4fd40 count:1 mapcount:0
mapping:0000000000000000 index:0x0
flags: 0xfffe00000001000(reserved)
raw: 0fffe00000001000 ffff7e0000c4fd48 ffff7e0000c4fd48
0000000000000000
raw: 0000000000000000 0000000000000000 00000001ffffffff
0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags: 0x1000(reserved)
Modules linked in:
CPU: 49 PID: 1 Comm: swapper/0 Not tainted
5.1.0-rc1-43081-g22d97fd-dirty #1433
Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI
RC0 - V1.12.01 01/29/2019
Call trace:
dump_backtrace+0x0/0x118
show_stack+0x14/0x1c
dump_stack+0xa4/0xc8
bad_page+0xe4/0x13c
free_pages_check_bad+0x4c/0xc0
__free_pages_ok+0x30c/0x340
__free_pages+0x30/0x44
__dma_direct_free_pages+0x30/0x38
dma_direct_free+0x24/0x38
dma_free_attrs+0x9c/0xd8
dmam_release+0x20/0x28
release_nodes+0x17c/0x220
devres_release_all+0x34/0x54
really_probe+0xc4/0x2c8
driver_probe_device+0x58/0xfc
device_driver_attach+0x68/0x70
__driver_attach+0x94/0xdc
bus_for_each_dev+0x5c/0xb4
driver_attach+0x20/0x28
bus_add_driver+0x14c/0x200
driver_register+0x6c/0x124
__pci_register_driver+0x48/0x50
sas_v3_pci_driver_init+0x20/0x28
do_one_initcall+0x40/0x25c
kernel_init_freeable+0x2b8/0x3c0
kernel_init+0x10/0x100
ret_from_fork+0x10/0x18
Disabling lock debugging due to kernel taint
BUG: Bad page state in process swapper/0 pfn:313f6
page:ffff7e0000c4fd80 count:1 mapcount:0
mapping:0000000000000000 index:0x0
[ 89.322983] flags: 0xfffe00000001000(reserved)
raw: 0fffe00000001000 ffff7e0000c4fd88 ffff7e0000c4fd88
0000000000000000
raw: 0000000000000000 0000000000000000 00000001ffffffff
0000000000000000
The crash occurs for the same reason.
In this case, on the really_probe() failure path, we are still clearing
the DMA ops prior to releasing the device's managed memories.
This patch fixes this issue by reordering the DMA ops teardown and the
call to devres_release_all() on the failure path.
Reported-by: Xiang Chen <chenxiang66@hisilicon.com>
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since insert_resource() might return an error we don't need
to shadow its error code and would safely propagate to the user.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment hasn't been accurate for several years.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
smp_mb__before_atomic() can not be applied to atomic_set(). Remove the
barrier and rely on RELEASE synchronization.
Fixes: ba16b2846a ("kernfs: add an API to get kernfs node from inode number")
Cc: stable@vger.kernel.org
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e1ede312f1 ("xprtrdma: Fix helper that drains the
transport") replaced the ib_drain_qp() call, so update documenting
comments to reflect current operation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: rely on the trace points instead.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up.
Move the remaining field in rpcrdma_create_data_internal so the
structure can be removed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up.
The inline settings are actually a characteristic of the endpoint,
and not related to the device. They are also modified after the
transport instance is created, so they do not belong in the cdata
structure either.
Lastly, let's use names that are more natural to RDMA than to NFS:
inline_write -> inline_send and inline_read -> inline_recv. The
/proc files retain their names to avoid breaking user space.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
After commit 396eaf21ee ("blk-mq: improve DM's blk-mq IO merging via
blk_insert_cloned_request feedback"), map_request() will requeue the tio
when issued clone request return BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE.
Thus, if device driver status is error, a tio may be requeued multiple
times until the return value is not DM_MAPIO_REQUEUE. That means
type->start_io may be called multiple times, while type->end_io is only
called when IO complete.
In fact, even without commit 396eaf21ee, setup_clone() failure can
also cause tio requeue and associated missed call to type->end_io.
The service-time path selector selects path based on in_flight_size,
which is increased by st_start_io() and decreased by st_end_io().
Missed calls to st_end_io() can lead to in_flight_size count error and
will cause the selector to make the wrong choice. In addition,
queue-length path selector will also be affected.
To fix the problem, call type->end_io in ->release_clone_rq before tio
requeue. map_info is passed to ->release_clone_rq() for map_request()
error path that result in requeue.
Fixes: 396eaf21ee ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Cc: stable@vger.kernl.org
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Clean up.
xprt_rdma_max_inline_{read,write} cannot be set to large values
by virtue of proc_dointvec_minmax. The current maximum is
RPCRDMA_MAX_INLINE, which is much smaller than RPCRDMA_MAX_SEGS *
PAGE_SIZE.
The .rsize and .wsize fields are otherwise unused in the current
code base, and thus can be removed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The PLLs on the sam9x60 (PLLA and USB PLL) use a different register set and
programming model than the previous SoCs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The sam9x60 cpu clock is located at a different offset but is otherwise
similar to the master clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The sam9x60 USB clock supports four different parents, ensure they can be
selected.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PCR register layout for GCLKCSS is changing for the future SoCs, allow
configuring it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PCR register actually changed layout for each SoC. By chance, this
didn't have impact on sama5d[2-4] support but since sama5d3, PID is seven
bits wide and sama5d4 and sama5d2 don't have DIV.
For the DT backward compatibility, keep the layout as is.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the 4 Quadrature counters for this board.
Reviewed-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds documentation for the specific prescaler entry.
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver exposes the counter for the quadrature decoder of the
FlexTimer Module, present in the LS1021A soc.
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common #defines have been moved to "linux/fsl/ftm.h". Thus making use of
this file.
Also FTM_SC_CLK_SHIFT has been renamed to FTM_SC_CLK_MASK_SHIFT.
Reviewed-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This also fixes the wrong value for the previously defined
FTM_MODE_INIT macro (it was not used).
Reviewed-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several files are/will be using the same #defines to use the Flextimer
module. Regroup them in a common file.
Reviewed-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IIO counter subdirectory is now superceded by the Counter subsystem.
This patch adds deprecation warnings to the documentation of the
relevant IIO Counter sysfs attributes.
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The STM32 LP Timer counter driver now resides under the Counter
subsystem. This patch adjusts dt-bindings to account for the STM32
lptimer driver move.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for new counter device to stm32-lptimer.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add bindings for STM32 Timer quadrature encoder.
It is a sub-node of STM32 Timer which implement the
quadratic encoder part of the hardware.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
