In case spi_sync_locked fails, the fix reports the error and
returns the error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some controllers, in Present State Register, Data Line
Active bit is not reliable for commands (such as CMD6, CMD7,
CMD12, CMD28, CMD29, or CMD38) with busy signal. DLA affects
Command with Data Inhibit bit. Therefore, software driver
may not know the busy status in DLA/CDIHB.
Futunately MMC core driver has already polled card status
with CMD13 after sending any command with busy signal. So
we can just ignore CDIHB never released issue for such
controllers. This patch is to add a quirk to handle this.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Invalid Transfer Complete (IRQSTAT[TC]) bit could be set during
multi-write operation even when the BLK_CNT in BLKATTR register
has not reached zero. Therefore, Transfer Complete might be
reported twice due to this erratum since a valid Transfer Complete
occurs when BLK_CNT reaches zero. This erratum is to fix this issue
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the event of that any data error (like, IRQSTAT[DCE]) occurs
during an eSDHC data transaction where DMA is used for data
transfer to/from the system memory, setting the SYSCTL[RSTD]
register may cause a system hang. If software sets the register
SYSCTL[RSTD] to 1 for error recovery while DMA transferring is
not complete, eSDHC may hang the system bus. This happens because
the software register SYSCTL[RSTD] resets the DMA engine without
waiting for the completion of pending system transactions. This
erratum is to fix this issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not
reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock),
and 0xC(2^25 SD clock). The data timeout counter can count from
2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout
counter counts for only 2^13 SD clocks.
A-008358: The data timeout counter value loaded into the timeout
counter is less than expected and can result into early timeout
error in case of eSDHC data transactions. The table below shows
the expected vs actual timeout period for different values of
SYSCTL[DTOCV]:
these two erratum has the same quirk to control it, and set
SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Software writing to the Transfer Type configuration register
(system clock domain) can cause a setup/hold violation in the
CRC flops (card clock domain), which can cause write accesses
to be sent with corrupt CRC values. This issue occurs only for
write preceded by read. this erratum is to fix this issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to add erratum A011334 support in lx2160 2.0 SoC
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmci_variant_init() is a local function to mmci.c, let's convert it into
static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It's good practice to share functions via header files, rather than from
the c-files. Therefore, let's move sdmmc_variant_init() to mmci.h.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It seems a bit silly to have a header file to share only the
qcom_variant_init() function. So, let's just drop it and move the
declaration of the function into the common mmci.h instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Having mmci_dmae_start() to invoke the shared function, dml_start_xfer(),
explicitly for the qcom variant isn't very nice. Let's clean up this code
by moving the qcom specific parts into the qcom ->dma_start() callback and
then drop dml_start_xfer() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
There's no point clearing the variant flag in case the qcom variant fails
to setup DMA. This is because if mmci_dma_setup() fails, then the use_dma
flag remains set to false, which leads to mmci using PIO mode and not DMA.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Some of the DMA functions are shared via mmci.h, however they are not
implemented unless CONFIG_DMA_ENGINE is set. Therefore, add that constraint
to the header file as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This fixes the -WDecl sparse warning in journal.c. Function was declared
as static void but the definition was void.
Signed-off-by: Bharath Vedartham <linux.bhar@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Currently the bitwise operations on the u16 variable 'status' with
the setting ROCKCHIP_PCIE_EP_CMD_STATUS_IS are incorrect because
ROCKCHIP_PCIE_EP_CMD_STATUS_IS is 1UL<<19 which is wider than the
u16 variable.
Fix this by making status a u32.
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
The device reports Synch: Synchronous on the playback interface.
This causes regular audible napping on sample rates that are not multiples
of 1 kHz. Fix to Synch: Asynchronous.
Specifically observed on Focusrite Scarlett Solo 2nd generation. I assume
the first generation model has a different device ID. A first generation
Scarlett 2i2 I was able to test advertised Synch: Asynchronous by default.
For example, with a sample rate of 44100 Hz, a silent sample is played
every 40.96 seconds (likely 44.0 samples instead of 44.1 transmitted per
USB frame on average, 4096 being the size of some internal buffer).
There may be some other bug at play here since this doesn't happen
on other platforms. However, a feedback endpoint is listed and using it
fixes the issue. That is the only change in the quirk,
but I didn't find a way to declare only it.
Tested on two units and on two different computers.
Signed-off-by: Roope Salmi <rpsalmi@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a default quality to hw_random device to be
automatically set as new default entropy. Setting
random quality will decrease the crng init time by
switching to this hardware random source.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No remove function implemented yet in the driver.
Without remove function, the pm_runtime implementation
complains when removing and probing again the driver.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
spdxcheck.py complains:
drivers/power/supply/goldfish_battery.c: 1:28 Invalid License ID: GPL
which is correct because GPL is not a valid identifier. Of course this
could have been caught by checkpatch.pl _before_ submitting or merging the
patch.
WARNING: 'SPDX-License-Identifier: GPL' is not supported in LICENSES/...
#19: FILE: drivers/power/supply/goldfish_battery.c:1:
+// SPDX-License-Identifier: GPL
Which is absolutely hillarious as the commit introducing this wreckage says
in the changelog:
There was a checkpatch complain:
"Missing or malformed SPDX-License-Identifier tag".
Oh well. Replacing a checkpatch warning by a different checkpatch warning
is a really useful exercise.
Use the proper GPL-2.0 identifier which is what the boiler plate in the
file had originally.
Fixes: e75e3a125b ("drivers: power: supply: goldfish_battery: Put an SPDX tag")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the driver is handling all i.MX5 series SoCs inlcuding i.MX50, rather
than just i.MX51 and i.MX53, let's rename it to clk-imx5.c.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
when CONFIG_INET is not enabled:
net/xfrm/xfrm_output.c: In function ‘xfrm4_tunnel_encap_add’:
net/xfrm/xfrm_output.c:234:2: error: implicit declaration of function ‘ip_select_ident’ [-Werror=implicit-function-declaration]
ip_select_ident(dev_net(dst->dev), skb, NULL);
XFRM only supports ipv4 and ipv6 so change dependency to INET and place
user-visible options (pfkey sockets, migrate support and the like)
under 'if INET' guard as well.
Fixes: 1de7083006 ("xfrm: remove output2 indirection from xfrm_mode")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
There is one compiling error in u2fzero_probe()->u2fzero_init_hwrng(),
this is because HW_RANDOM is not set.
drivers/hid/hid-u2fzero.o: In function `u2fzero_probe':
hid-u2fzero.c:(.text+0xc70): undefined reference to `devm_hwrng_register'
Fixes: 42337b9d4d958("HID: add driver for U2F Zero built-in LED and RNG")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Banana Pi M2 Zero board has an AP6212 BT+Wifi combo chip
with Broadcom internals attached to UART1 and some gpios.
This addition is in line with similar boards.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The struct voltage_map_desc is used for storing min/max/step fileds, and
then setup the min_uV, uV_step and n_voltages fields for regulator_desc.
Introduce MAX8998_LINEAR_REG/MAX8998_OTHERS_REG macro to setup these filds
directly in regulator_desc to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so we don't need to store
*rdev for clean up, use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_get_current_limit_regmap helper to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so we don't need to save
*regulator for clean up, use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ab8500_ext_regulator_ops never need to be modified, make it const so
compiler can put it to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add functions.sh to TEST_PROGS_EXTENDED so that it is installed along
with the rest of the selftests and they can be run.
Originally-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Use regulator core's simplified DT parsing code to simplify the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so we don't need to save
*rdev for clean up, use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the "reg-names" property from the display node of R-Car Gen3 R8A77965
device tree.
No other mainline R-Car Gen3 SoC has that property specified.
Fixes: 2f2c71bfc8 ("arm64: dts: renesas: r8a77965: Populate the DU instance placeholder")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[reworded commit message, sent upstream]
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In commit b1fca27d38 ("kernel debug: support resetting WARN*_ONCE")
we got the opportunity to reset state on the one shot messages,
without having to reboot.
However printk_once (printk_deferred_once) live in a different file
and didn't get the same kind of update/conversion, so they remain
unconditionally one shot, until the system is rebooted.
For example, we currently have:
sched/rt.c: printk_deferred_once("sched: RT throttling activated\n");
..which could reasonably be tripped as someone is testing and tuning
a new system/workload and their task placements. For consistency, and
to avoid reboots in the same vein as the original commit, we make these
two instances of _once the same as the WARN*_ONCE instances are.
Link: http://lkml.kernel.org/r/1555121491-31213-1-git-send-email-paul.gortmaker@windriver.com
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
This patch adds FPGA Manager support for the Xilinx
ZynqMP chip.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add documentation to describe Xilinx ZynqMP fpga driver
bindings.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Tull <atull@kernel.org>
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This Patch Adds fpga API's to support the Bitstream loading
by using firmware interface.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The device node dereferences are out of order, sort them.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
MMC1 is used on some H6 boards we want to support. Typical use is 4-bit
SDIO interface with a WiFi chip. Add pin definitions for this use case.
As this is the only possible configration for mmc1, make it the default
one, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The debug feature entries have been used with up to 5 arguents
(including the pointer to the format string) but there was only
space reserved for 4 arguemnts. So now the registration does
reserve space for 5 times a long value.
This fixes a sometime appearing weired value as the last
value of an debug feature entry like this:
... pkey_sec2protkey zcrypt_send_cprb (cardnr=10 domain=12)
failed with errno -2143346254
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Christian Rund <Christian.Rund@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Sven Auhagen reported that a 2nd ping request will fail if 'fully-random'
mode is used.
Reason is that if no proto information is given, min/max are both 0,
so we set the icmp id to 0 instead of chosing a random value between
0 and 65535.
Update test case as well to catch this, without fix this yields:
[..]
ERROR: cannot ping ns1 from ns2 with ip masquerade fully-random (attempt 2)
ERROR: cannot ping ns1 from ns2 with ipv6 masquerade fully-random (attempt 2)
... becaus 2nd ping clashes with existing 'id 0' icmp conntrack and gets
dropped.
Fixes: 203f2e7820 ("netfilter: nat: remove l4proto->unique_tuple")
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I believe that "hook->num" can be up to UINT_MAX. Shifting more than
31 bits would is undefined in C but in practice it would lead to shift
wrapping. That would lead to an array overflow in nf_tables_addchain():
ops->hook = hook.type->hooks[ops->hooknum];
Fixes: fe19c04ca1 ("netfilter: nf_tables: remove nhooks field from struct nft_af_info")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
else, we leak the addresses to userspace via ctnetlink events
and dumps.
Compute an ID on demand based on the immutable parts of nf_conn struct.
Another advantage compared to using an address is that there is no
immediate re-use of the same ID in case the conntrack entry is freed and
reallocated again immediately.
Fixes: 3583240249 ("[NETFILTER]: nf_conntrack_expect: kill unique ID")
Fixes: 7f85f91472 ("[NETFILTER]: nf_conntrack: kill unique ID")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[Why]
We used this change to investigate the performance of bandwidth validation,
it will be useful to have if we need to investigate further.
[How]
We use performance counter tick numbers to profile performance, they live
at dc->debug.bw_val_profile (set .enable in debugger to turn on measuring).
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a fast_validate parameter in dc_validate_global_state for future use
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
