This RTC handles dates after 2106 (up to July 2554), call the 64bit
versions of rtc_tm time conversion.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion as the range is enforced
by the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is no point in caching alarm_time for .read_alarm because
.read_alarm is only called at boo time and thus alarm_time is always 0.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
struct before requesting the IRQ.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix checkpatch error:
drivers/rtc/rtc-test.c:155: ERROR: do not use assignment in if condition
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This makes it possible to probe the X1205 RTC from the
device tree. This is needed when adding device tree boot
support for the IXP4xx-based NSLU2 which has this RTC.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This adds device tree bindings for the Xircom X1205 RTC found
in the Linksys NSLU2.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[alexandre.belloni@bootlin.com: move doc to rtc.txt]
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Covnert the header of the source file to SPDX.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Let the core handle the RTC range instead of open coding it.
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This RTC handles time from 2000-01-01 00:00:00 to 2099-12-31 23:59:59 with
a weird rollover to 2000-06-23 00:00:00.
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This allows further improvement of the driver.
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There is no need to reset controller every time, do this
once in pdm_probe.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add default regs value for controller.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch set left justified store mode default.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch decreases the transfer bursts to avoid the fifo overrun.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is because set_fmt ops maybe called when PD is off,
and in such case, regmap_ops will lead system hang.
enale PD before doing regmap_ops.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit da215354eb ("ASoC: simple-card: merge simple-scu-card")
merged simple-scu-audio-card which can handle DPCM into
simple-audio-card.
By this patch, the judgement to select "normal sound card" or
"DPCM sound card" is based on its CPU/Codec DAI count.
But, because of it, existing "simple-audio-card" user who is
assuming "normal sound card" might select DPCM unintentionally.
To solve this issue, this patch allows "simple-audio-card" user
can select "normal sound card", and "simple-scu-audio-card" user
can select both "normal sound card" and "DPCM sound card".
This keeps compatibility collectry.
Fixes: da215354eb ("ASoC: simple-card: merge simple-scu-card")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit ae3cb57909 ("ASoC: audio-graph-card: merge
audio-graph-scu-card") merged audio-graph-scu-card which can
handle DPCM into audio-graph-card.
By this patch, the judgement to select "normal sound card" or
"DPCM sound card" is based on its OF-graph endpoint connection.
But, because of it, existing "audio-graph-card" user who is
assuming "normal sound card" might select DPCM unintentionally.
To solve this issue, this patch allows "audio-graph-card" user
can select "normal sound card", and "audio-graph-scu-card" user
can select both "normal sound card" and "DPCM sound card".
This keeps compatibility collectry.
Fixes: ae3cb57909 ("ASoC: audio-graph-card: merge audio-graph-scu-card")
Reported-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of debug and optional GPIO requested, the gpiod_put() is not aware of
and will WARN, which is not the case.
Make gpiod_put() NULL-aware to keep silent for optional GPIOs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add an explanation why zero width check is needed when generating factor
mask using GENMASK() macro.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Video related clocks need to set rate as close as possible to the
requested one, so they should be able to change parent clock rate.
When processing 4K video, VPU clock has to be set to higher rate than it
is default parent rate. Because of that, VPU clock should be able to
change parent clock rate.
Add CLK_SET_RATE_PARENT flag to tcon-lcd0, tcon-tv0 and ve.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We have for the H3 boards some kind of cargo cult apparently, where we
would have a pinctrl node even for GPIOs without any particular settings.
This is pretty much useless, so let's remove them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
So far we've enabled pull-up and pull-down resistors on GPIOs using a
pinctrl node. Now that the GPIO binding allows for a flag to declare this,
let's switch to it.
This brings us closer to removing all the GPIO pinctrl nodes, which will in
turn allow us to switch the pinctrl strict mode on.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
-----BEGIN PGP SIGNATURE-----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=TvT3
-----END PGP SIGNATURE-----
Merge tag '5.1-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb3 fixes from Steve French:
"Four smb3 fixes for stable:
- fix an open path where we had an unitialized structure
- fix for snapshot (previous version) enumeration
- allow reconnect timeout on handles to be configurable to better
handle network or server crash
- correctly handle lack of file_all_info structure"
* tag '5.1-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: a smb2_validate_and_copy_iov failure does not mean the handle is invalid.
SMB3: Allow persistent handle timeout to be configurable on mount
smb3: Fix enumerating snapshots to Azure
cifs: fix kref underflow in close_shroot()
New pt_regs should indicate that there's no syscall, not that there's
syscall #0. While at it wrap macro body in do/while and parenthesize
macro arguments.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Syscall may alter pt_regs structure passed to it, resulting in a
mismatch between syscall entry end syscall exit entries in the ftrace.
Temporary restore syscall field of the pt_regs for the duration of
do_syscall_trace_leave.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Convert GPIO chip selects in the Renesas MSIOF SPI driver from legacy
GPIO numbers to GPIO descriptors.
Notes:
- The board file for the SH7724-based Ecovec24 development board now
registers a GPIO descriptor lookup, instead of passing a GPIO number
through controller_data,
- sh_msiof_get_cs_gpios() must release all GPIOs, else
spi_get_gpio_descs() cannot claim them during SPI controller
registration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 5fd917afc4 ("spi: bcm2835aux: make the polling duration limits configurable")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While devm_gpiod_get_index_optional() returns NULL if the GPIO is not
present (i.e. -ENOENT), it may still return other error codes, like
-EPROBE_DEFER. Currently these are not handled, leading to
unrecoverable failures later in case of probe deferral:
gpiod_set_consumer_name: invalid GPIO (errorpointer)
gpiod_direction_output: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
Detect and propagate errors to fix this.
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from GPIO numbers to GPIO descriptors removed the use of
spi->controller_data, but forgot to update a comment referring to it.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the copyright dates and use the SPDX identifier instead
of reciting the license.
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the unnecessary validation of the 'cstream' variable to fix
below smatch warning:
sprd_platform_compr_drain_notify() warn: variable dereferenced
before check 'cstream' (see line 105)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
