The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ti/netcp_ethss.c:3661:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
./drivers/net/ethernet/ti/netcp_ethss.c:3665:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to ehea_get_eth_dn returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ibm/ehea/ehea_main.c:3163:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3154, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Douglas Miller <dougmill@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
After 90eff9096c ("net: phy: Allow splitting MDIO bus/device support
from PHYs") the various MDIO bus drivers were no longer parented with
config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix
this by depending on MDIO_DEVICE which is a menuconfig.
This is visually nicer and less confusing for users.
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tristate prompt should have been replaced rather than defined a few
lines below, rebase mistake.
Fixes: 17cc982176 ("net: phy: Move Omega PHY entry to Cygnus PHY driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Valentin reported that unplugging a CPU occasionally results in a warning
in the tick broadcast code which is triggered when an offline CPU is in the
broadcast mask.
This happens because the outgoing CPU is not removing itself from the
broadcast masks, especially not from the broadcast_force_mask. The removal
happens on the control CPU after the outgoing CPU is dead. It's a long
standing issue, but the warning is harmless.
Rework the hotplug mechanism so that the outgoing CPU removes itself from
the broadcast masks after disabling interrupts and removing itself from the
online mask.
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1903211540180.1784@nanos.tec.linutronix.de
-----BEGIN PGP SIGNATURE-----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=l4lx
-----END PGP SIGNATURE-----
Merge tag 'io_uring-20190323' of git://git.kernel.dk/linux-block
Pull io_uring fixes and improvements from Jens Axboe:
"The first five in this series are heavily inspired by the work Al did
on the aio side to fix the races there.
The last two re-introduce a feature that was in io_uring before it got
merged, but which I pulled since we didn't have a good way to have
BVEC iters that already have a stable reference. These aren't
necessarily related to block, it's just how io_uring pins fixed
buffers"
* tag 'io_uring-20190323' of git://git.kernel.dk/linux-block:
block: add BIO_NO_PAGE_REF flag
iov_iter: add ITER_BVEC_FLAG_NO_REF flag
io_uring: mark me as the maintainer
io_uring: retry bulk slab allocs as single allocs
io_uring: fix poll races
io_uring: fix fget/fput handling
io_uring: add prepped flag
io_uring: make io_read/write return an integer
io_uring: use regular request ref counts
-----BEGIN PGP SIGNATURE-----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=4Ktc
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190323' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of fixes/changes that should go into this series. This contains:
- Kernel doc / comment updates (Bart, Shenghui)
- Un-export of core-only used function (Bart)
- Fix race on loop file access (Dongli)
- pf/pcd queue cleanup fixes (me)
- Use appropriate helper for RESTART bit set (Yufen)
- Use named identifier for classic poll (Yufen)"
* tag 'for-linus-20190323' of git://git.kernel.dk/linux-block:
sbitmap: trivial - update comment for sbitmap_deferred_clear_bit
blkcg: Fix kernel-doc warnings
blk-iolatency: #include "blk.h"
block: Unexport blk_mq_add_to_requeue_list()
block: add BLK_MQ_POLL_CLASSIC for hybrid poll and return EINVAL for unexpected value
blk-mq: remove unused 'nr_expired' from blk_mq_hw_ctx
loop: access lo_backing_file only when the loop device is Lo_bound
blk-mq: use blk_mq_sched_mark_restart_hctx to set RESTART
paride/pcd: cleanup queues when detection fails
paride/pf: cleanup queues when detection fails
for stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAlyVCYsTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi6oFB/9Lw2OMiNrdMAgfOzcVkB4dbXbRtryG
rBsTUc/fwFrCl2N+wRmJKUkDP1e1phM9CHaGEoBYB+vL2Hhj8kjyJN4NY1g09ilt
w8XT6Pkg2Uui4kr5bnWzDS+oO8hm1ES2PbzDnIX1UiLStHypzQFwzvlm+TQE8jxb
pGNyNnbASJ+2mk+xAz7EkLGlNcAgULUT7oC/w0xj0neM739aYS3IsZgWylnw41CS
59TDyWROUUePLQnvieXmp4l58fn7xpvwrUE0KQgYec+j2t2SsKnHUoI86qZFYF2Q
NsE/K2fmIvKxWrmNw+0uuOVj+mNr2Jr5m/q+Nu61asOjs7Hz5CwUp7nd
=DkXC
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.1-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A follow up for the new alloc_size logic and a blacklisting fix,
marked for stable"
* tag 'ceph-for-5.1-rc2' of git://github.com/ceph/ceph-client:
rbd: drop wait_for_latest_osdmap()
libceph: wait for latest osdmap in ceph_monc_blacklist_add()
rbd: set io_min, io_opt and discard_granularity to alloc_size
The Hygon family 18h multi-die processor platform supports 1, 2 or
4-Dies per socket. The topology looks like this:
System View (with 1-Die 2-Socket):
|------------|
------ -----
SOCKET0 | D0 | | D1 | SOCKET1
------ -----
System View (with 2-Die 2-socket):
--------------------
| -------------|------
| | | |
------------ ------------
SOCKET0 | D1 -- D0 | | D3 -- D2 | SOCKET1
------------ ------------
System View (with 4-Die 2-Socket) :
--------------------
| -------------|------
| | | |
------------ ------------
| D1 -- D0 | | D7 -- D6 |
| | \/ | | | | \/ | |
SOCKET0 | | /\ | | | | /\ | | SOCKET1
| D2 -- D3 | | D4 -- D5 |
------------ ------------
| | | |
------|------------| |
--------------------
Currently
phys_proc_id = initial_apicid >> bits
calculates the physical processor ID from the initial_apicid by shifting
*bits*.
However, this does not work for 1-Die and 2-Die 2-socket systems.
According to document [1] section 2.1.11.1, the bits is the value of
CPUID_Fn80000008_ECX[12:15]. The possible values are 4, 5 or 6 which
mean:
4 - 1 die
5 - 2 dies
6 - 3/4 dies.
Hygon programs the initial ApicId the same way as AMD. The ApicId is
read from CPUID_Fn00000001_EBX (see section 2.1.11.1 of referrence [1])
and the definition is as below (see section 2.1.10.2.1.3 of [1]):
-------------------------------------------------
Bit | 6 | 5 4 | 3 | 2 1 0 |
|-----------|---------|--------|----------------|
IDs | Socket ID | Node ID | CCX ID | Core/Thread ID |
-------------------------------------------------
So for 3/4-Die configurations, the bits variable is 6, which is the same
as the ApicID definition field.
For 1-Die and 2-Die configurations, bits is 4 or 5, which will cause the
right shifted result to not be exactly the value of socket ID.
However, the socket ID should be obtained from ApicId[6]. To fix the
problem and match the ApicID field definition, set the shift bits to 6
for all Hygon family 18h multi-die CPUs.
Because AMD doesn't have 2-Socket systems with 1-Die/2-Die processors
(see reference [2]), this doesn't need to be changed on the AMD side but
only for Hygon.
References:
[1] https://www.amd.com/system/files/TechDocs/54945_PPR_Family_17h_Models_00h-0Fh.pdf
[2] https://www.amd.com/en/products/specifications/processors
[bp: heavily massage commit message. ]
Signed-off-by: Pu Wen <puwen@hygon.cn>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Lendacky <Thomas.Lendacky@amd.com>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1553355740-19999-1-git-send-email-puwen@hygon.cn
The ext4 fstrim implementation uses the block bitmaps to find free space
that can be discarded. If we haven't replayed the journal, the bitmaps
will be stale and we absolutely *cannot* use stale metadata to zap the
underlying storage.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
During a read failover, we may end up changing the value of
the pgio_mirror_idx, so make sure that we record the layout
stats before that update.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Specifying a retrans=0 mount parameter to a NFS/TCP mount, is
inadvertently causing the NFS client to rewrite any specified
timeout parameter to the default of 60 seconds.
Fixes: a956beda19 ("NFS: Allow the mount option retrans=0")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Currently, we are releasing the indirect buffer where we are done with
it in ext4_ind_remove_space(), so we can see the brelse() and
BUFFER_TRACE() everywhere. It seems fragile and hard to read, and we
may probably forget to release the buffer some day. This patch cleans
up the code by putting of the code which releases the buffers to the
end of the function.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
If the transport is still connected, then we do want to allow
RPC_SOFTCONN tasks to retry. They should time out if and only if
the connection is broken.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
All indirect buffers get by ext4_find_shared() should be released no
mater the branch should be freed or not. But now, we forget to release
the lower depth indirect buffers when removing space from the same
higher depth indirect block. It will lead to buffer leak and futher
more, it may lead to quota information corruption when using old quota,
consider the following case.
- Create and mount an empty ext4 filesystem without extent and quota
features,
- quotacheck and enable the user & group quota,
- Create some files and write some data to them, and then punch hole
to some files of them, it may trigger the buffer leak problem
mentioned above.
- Disable quota and run quotacheck again, it will create two new
aquota files and write the checked quota information to them, which
probably may reuse the freed indirect block(the buffer and page
cache was not freed) as data block.
- Enable quota again, it will invoke
vfs_load_quota_inode()->invalidate_bdev() to try to clean unused
buffers and pagecache. Unfortunately, because of the buffer of quota
data block is still referenced, quota code cannot read the up to date
quota info from the device and lead to quota information corruption.
This problem can be reproduced by xfstests generic/231 on ext3 file
system or ext4 file system without extent and quota features.
This patch fix this problem by releasing the missing indirect buffers,
in ext4_ind_remove_space().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@kernel.org
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
With -Wimplicit-fallthrough added to CFLAGS:
kernel/irq/manage.c: In function ‘irq_do_set_affinity’:
kernel/irq/manage.c:198:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
cpumask_copy(desc->irq_common_data.affinity, mask);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
kernel/irq/manage.c:199:2: note: here
case IRQ_SET_MASK_OK_NOCOPY:
^~~~
Annotate it.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20190228213714.GA9246@embeddedor
For all riscv architectures (RV32, RV64 and RV128), the clocksource
is a 64 bit incrementing counter.
Fix the clock source mask accordingly.
Tested on both 64bit and 32 bit virt machine in QEMU.
Fixes: 62b0194368 ("clocksource: new RISC-V SBI timer driver")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-riscv@lists.infradead.org
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Anup Patel <Anup.Patel@wdc.com>
Cc: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190322215411.19362-1-atish.patra@wdc.com
On machines where the GART aperture is mapped over physical RAM,
/proc/kcore contains the GART aperture range. Accessing the GART range via
/proc/kcore results in a kernel crash.
vmcore used to have the same issue, until it was fixed with commit
2a3e83c6f9 ("x86/gart: Exclude GART aperture from vmcore")', leveraging
existing hook infrastructure in vmcore to let /proc/vmcore return zeroes
when attempting to read the aperture region, and so it won't read from the
actual memory.
Apply the same workaround for kcore. First implement the same hook
infrastructure for kcore, then reuse the hook functions introduced in the
previous vmcore fix. Just with some minor adjustment, rename some functions
for more general usage, and simplify the hook infrastructure a bit as there
is no module usage yet.
Suggested-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Dave Young <dyoung@redhat.com>
Link: https://lkml.kernel.org/r/20190308030508.13548-1-kasong@redhat.com
The timekeeping code uses a random mix of "unsigned long" and "unsigned
int" for the seqcount snapshots (ratio 14:12). Since the seqlock.h API is
entirely based on unsigned int, use that throughout.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190318195557.20773-1-linux@rasmusvillemoes.dk
Stratix10 Double Bit Error Address was always read from SDRAM Address
register instead of each device's Address register.
To determine which device had the DBE, cycle through the EDAC devices
comparing the DBE value to the db_irq value. Once found, report the DBE
Address from the device registers as well as the device name.
Finally, notify the system via an SMC call and indicate the panic should
result in a system reboot. Change a run-time check to a Stratix10
compile-time check for a clean SMC notification.
Fixes: d5fc912556 ("EDAC, altera: Combine Stratix10 and Arria10 probe functions")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/1552490842-25440-1-git-send-email-thor.thayer@linux.intel.com
The following Kconfig constellations fail randconfig builds:
CONFIG_ACPI_NFIT=y
CONFIG_EDAC_DEBUG=y
CONFIG_EDAC_SKX=m
CONFIG_EDAC_I10NM=y
or
CONFIG_ACPI_NFIT=y
CONFIG_EDAC_DEBUG=y
CONFIG_EDAC_SKX=y
CONFIG_EDAC_I10NM=m
with:
...
CC [M] drivers/edac/skx_common.o
...
.../skx_common.o:.../skx_common.c:672: undefined reference to `__this_module'
That is because if one of the two drivers - skx_edac or i10nm_edac - is
built-in and the other one is a module, the shared file skx_common.c
gets linked into a module object by kbuild. Therefore, when linking that
same file into vmlinux, the '__this_module' symbol used in debugfs isn't
defined, leading to the above error.
Fix it by moving all debugfs code from skx_common.c to both skx_base.c
and i10nm_base.c respectively. Thus, skx_common.c doesn't refer to the
'__this_module' symbol anymore.
Clarify skx_common.c's purpose at the top of the file for future
reference, while at it.
[ bp: Make text more readable. ]
Fixes: d4dc89d069 ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190321221339.GA32323@agluck-desk
- check the return value of a function that can fail in gpio-exar
- fix the SPDX identifier in amd-fch
- fix the direction_input callback in gpio-adnp
-----BEGIN PGP SIGNATURE-----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=1M3G
-----END PGP SIGNATURE-----
Merge tag 'gpio-5.1-rc2-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
GPIO fixes for v5.1-rc2
- check the return value of a function that can fail in gpio-exar
- fix the SPDX identifier in amd-fch
- fix the direction_input callback in gpio-adnp
Workaround problem with Samba responses to SMB3.1.1
null user (guest) mounts. The server doesn't set the
expected flag in the session setup response so we have
to do a similar check to what is done in smb3_validate_negotiate
where we also check if the user is a null user (but not sec=krb5
since username might not be passed in on mount for Kerberos case).
Note that the commit below tightened the conditions and forced signing
for the SMB2-TreeConnect commands as per MS-SMB2.
However, this should only apply to normal user sessions and not for
cases where there is no user (even if server forgets to set the flag
in the response) since we don't have anything useful to sign with.
This is especially important now that the more secure SMB3.1.1 protocol
is in the default dialect list.
An earlier patch ("cifs: allow guest mounts to work for smb3.11") fixed
the guest mounts to Windows.
Fixes: 6188f28bf6 ("Tree connect for SMB3.1.1 must be signed for non-encrypted shares")
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Paulo Alcantara <palcantara@suse.de>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
This patch fixes the following KASAN report:
[ 779.044746] BUG: KASAN: slab-out-of-bounds in string+0xab/0x180
[ 779.044750] Read of size 1 at addr ffff88814f327968 by task trace-cmd/2812
[ 779.044756] CPU: 1 PID: 2812 Comm: trace-cmd Not tainted 5.1.0-rc1+ #62
[ 779.044760] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-0-ga698c89-prebuilt.qemu.org 04/01/2014
[ 779.044761] Call Trace:
[ 779.044769] dump_stack+0x5b/0x90
[ 779.044775] ? string+0xab/0x180
[ 779.044781] print_address_description+0x6c/0x23c
[ 779.044787] ? string+0xab/0x180
[ 779.044792] ? string+0xab/0x180
[ 779.044797] kasan_report.cold.3+0x1a/0x32
[ 779.044803] ? string+0xab/0x180
[ 779.044809] string+0xab/0x180
[ 779.044816] ? widen_string+0x160/0x160
[ 779.044822] ? vsnprintf+0x5bf/0x7f0
[ 779.044829] vsnprintf+0x4e7/0x7f0
[ 779.044836] ? pointer+0x4a0/0x4a0
[ 779.044841] ? seq_buf_vprintf+0x79/0xc0
[ 779.044848] seq_buf_vprintf+0x62/0xc0
[ 779.044855] trace_seq_printf+0x113/0x210
[ 779.044861] ? trace_seq_puts+0x110/0x110
[ 779.044867] ? trace_raw_output_prep+0xd8/0x110
[ 779.044876] trace_raw_output_smb3_tcon_class+0x9f/0xc0
[ 779.044882] print_trace_line+0x377/0x890
[ 779.044888] ? tracing_buffers_read+0x300/0x300
[ 779.044893] ? ring_buffer_read+0x58/0x70
[ 779.044899] s_show+0x6e/0x140
[ 779.044906] seq_read+0x505/0x6a0
[ 779.044913] vfs_read+0xaf/0x1b0
[ 779.044919] ksys_read+0xa1/0x130
[ 779.044925] ? kernel_write+0xa0/0xa0
[ 779.044931] ? __do_page_fault+0x3d5/0x620
[ 779.044938] do_syscall_64+0x63/0x150
[ 779.044944] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 779.044949] RIP: 0033:0x7f62c2c2db31
[ 779.044955] Code: fe ff ff 48 8d 3d 17 9e 09 00 48 83 ec 08 e8 96 02
02 00 66 0f 1f 44 00 00 8b 05 fa fc 2c 00 48 63 ff 85 c0 75 13 31 c0
0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 55 53 48 89 d5 48
89
[ 779.044958] RSP: 002b:00007ffd6e116678 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[ 779.044964] RAX: ffffffffffffffda RBX: 0000560a38be9260 RCX: 00007f62c2c2db31
[ 779.044966] RDX: 0000000000002000 RSI: 00007ffd6e116710 RDI: 0000000000000003
[ 779.044966] RDX: 0000000000002000 RSI: 00007ffd6e116710 RDI: 0000000000000003
[ 779.044969] RBP: 00007f62c2ef5420 R08: 0000000000000000 R09: 0000000000000003
[ 779.044972] R10: ffffffffffffffa8 R11: 0000000000000246 R12: 00007ffd6e116710
[ 779.044975] R13: 0000000000002000 R14: 0000000000000d68 R15: 0000000000002000
[ 779.044981] Allocated by task 1257:
[ 779.044987] __kasan_kmalloc.constprop.5+0xc1/0xd0
[ 779.044992] kmem_cache_alloc+0xad/0x1a0
[ 779.044997] getname_flags+0x6c/0x2a0
[ 779.045003] user_path_at_empty+0x1d/0x40
[ 779.045008] do_faccessat+0x12a/0x330
[ 779.045012] do_syscall_64+0x63/0x150
[ 779.045017] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 779.045019] Freed by task 1257:
[ 779.045023] __kasan_slab_free+0x12e/0x180
[ 779.045029] kmem_cache_free+0x85/0x1b0
[ 779.045034] filename_lookup.part.70+0x176/0x250
[ 779.045039] do_faccessat+0x12a/0x330
[ 779.045043] do_syscall_64+0x63/0x150
[ 779.045048] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 779.045052] The buggy address belongs to the object at ffff88814f326600
which belongs to the cache names_cache of size 4096
[ 779.045057] The buggy address is located 872 bytes to the right of
4096-byte region [ffff88814f326600, ffff88814f327600)
[ 779.045058] The buggy address belongs to the page:
[ 779.045062] page:ffffea00053cc800 count:1 mapcount:0 mapping:ffff88815b191b40 index:0x0 compound_mapcount: 0
[ 779.045067] flags: 0x200000000010200(slab|head)
[ 779.045075] raw: 0200000000010200 dead000000000100 dead000000000200 ffff88815b191b40
[ 779.045081] raw: 0000000000000000 0000000000070007 00000001ffffffff 0000000000000000
[ 779.045083] page dumped because: kasan: bad access detected
[ 779.045085] Memory state around the buggy address:
[ 779.045089] ffff88814f327800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045093] ffff88814f327880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045097] >ffff88814f327900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045099] ^
[ 779.045103] ffff88814f327980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045107] ffff88814f327a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045109] ==================================================================
[ 779.045110] Disabling lock debugging due to kernel taint
Correctly assign tree name str for smb3_tcon event.
Signed-off-by: Paulo Alcantara (SUSE) <paulo@paulo.ac>
Signed-off-by: Steve French <stfrench@microsoft.com>
Fix Guest/Anonymous sessions so that they work with SMB 3.11.
The commit noted below tightened the conditions and forced signing for
the SMB2-TreeConnect commands as per MS-SMB2.
However, this should only apply to normal user sessions and not for
Guest/Anonumous sessions.
Fixes: 6188f28bf6 ("Tree connect for SMB3.1.1 must be signed for non-encrypted shares")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
It was mapped to EIO which can be confusing when user space
queries for an object GUID for an object for which the server
file system doesn't support (or hasn't saved one).
As Amir Goldstein suggested this is similar to ENOATTR
(equivalently ENODATA in Linux errno definitions) so
changing NT STATUS code mapping for OBJECTID_NOT_FOUND
to ENODATA.
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Amir Goldstein <amir73il@gmail.com>
dedupe_file_range operations is combiled into remap_file_range.
But it's always skipped for dedupe operations in function
cifs_remap_file_range.
Example to test:
Before this patch:
# dd if=/dev/zero of=cifs/file bs=1M count=1
# xfs_io -c "dedupe cifs/file 4k 64k 4k" cifs/file
XFS_IOC_FILE_EXTENT_SAME: Invalid argument
After this patch:
# dd if=/dev/zero of=cifs/file bs=1M count=1
# xfs_io -c "dedupe cifs/file 4k 64k 4k" cifs/file
XFS_IOC_FILE_EXTENT_SAME: Operation not supported
Influence for xfstests:
generic/091
generic/112
generic/127
generic/263
These tests report this error "do_copy_range:: Invalid
argument" instead of "FIDEDUPERANGE: Invalid argument".
Because there are still two bugs cause these test failed.
https://bugzilla.kernel.org/show_bug.cgi?id=202935https://bugzilla.kernel.org/show_bug.cgi?id=202785
Signed-off-by: Xiaoli Feng <fengxiaoli0714@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
When sending a rdata, transport may return -EAGAIN. In this case
we should re-obtain credits because the session may have been
reconnected.
Change in v2: adjust_credits before re-sending
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
When sending a wdata, transport may return -EAGAIN. In this case
we should re-obtain credits because the session may have been
reconnected.
Change in v2: adjust_credits before re-sending
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Add a small test that shows how to shape a TCP flow in tc-bpf
with EDT and ECN.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This helper is useful if a bpf tc filter sets skb->tstamp.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In case kmemdup fails, the fix goes to blk_err to avoid NULL
pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dynamic-debug statements for command payload output only get emitted
when the command is not ND_CMD_CALL. Move the output payload dumping
ahead of the early return path for ND_CMD_CALL.
Fixes: 31eca76ba2 ("...whitelisted dimm command marshaling mechanism")
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add pinctrl on the always-enabled debug UART AO.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add pinctrl on the always-enabled debug UART AO.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add pinctrl on the always-enabled debug UART AO.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the 3 UART nodes in the EE power domain with the corresponding
pinctrl nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the reset controller device of g12a SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the always on UART pinctrl setting to the g12a soc DT.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the peripheral and always-on pinctrl controllers to the g12a soc.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes and properties for the AO Clocks and Resets.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Correctly map the regulators used by tlv320aic3106.
Both 1.8V and 3.3V for the codec is derived from VBAT via fixed regulators.
Cc: <Stable@vger.kernel.org> # v4.14+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Correctly map the regulators used by tlv320aic3106.
Both 1.8V and 3.3V for the codec is derived from VBAT via fixed regulators.
Cc: <Stable@vger.kernel.org> # v4.14+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add an of_node_put when a tested device node is not available.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
identifier f;
local idexpression e;
expression x;
@@
e = f(...);
... when != of_node_put(e)
when != x = e
when != e = x
when any
if (<+...of_device_is_available(e)...+>) {
... when != of_node_put(e)
(
return e;
|
+ of_node_put(e);
return ...;
)
}
// </smpl>
Fixes: e0c827aca0 ("drm/omap: Populate DSS children in omapdss driver")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to request dynamic allocationn of GPIO IDs, a negative number
should be passed as a base GPIO ID via platform data. Unfortuntely,
commit 771e53c4d1 ("ARM: OMAP1: ams-delta: Drop board specific global
GPIO numbers") didn't follow that rule while switching to dynamically
allocated GPIO IDs for Amstrad Delta latches, making their IDs
overlapping with those already assigned to OMAP GPIO devices. Fix it.
Fixes: 771e53c4d1 ("ARM: OMAP1: ams-delta: Drop board specific global GPIO numbers")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix sparse warning:
drivers/clocksource/mips-gic-timer.c:70:18: warning:
symbol 'gic_compare_irqaction' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20190322144359.19516-1-yuehaibing@huawei.com
Fix sparse warning:
drivers/clocksource/timer-ti-dm.c:589:5: warning:
symbol 'omap_dm_timer_set_load_start' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20190322144302.6704-1-yuehaibing@huawei.com
