Current code is using msleep when polling for hw ready. Unfortunately the
msleep routine isn't very accurate on rescheduling. In fact, on a busy
systems which reset the adapter, it became 10s of seconds before it was
rescheduled.
Fix by busy waiting using udelay. As we're now busy waiting, significantly
reduce the wait time so that we can exit the pool loop as soon as possible.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter. Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.
Add coordination between the two threads. The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path. Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a couple of cases, the driver detected a pci error (via pci device state
or via failed register reads) but didn't take any action to disable the
device. Additionally, the driver is ignoring the status of pci
configuration space reads.
Having the driver take the adapter offline whenever the pci error is
detected. Pay attention to pci_config_space_read status and return failure
if an error is seen.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an adapter fails, causing a board reset, the board reset routine
lpfc_hba_down_s4() takes the hbalock out then calls
lpfc_nvmet_ctxbuf_post() who then tries to take out the same lock. As the
context lists are now protected under the buf_list_locks, there is no need
for the hbalock to be held by the board reset routine.
Fix by no longer taking the hbalock in the board reset routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With negative test injection, the driver is receiving a command with first
burst enabled, meaning Sequence initiative is not passed with the command
frame. The driver notes the condition and discards the frame. However the
driver calls the incorrect buffer free routine, resulting in a NULL pointer
reference.
For hbq buffer free, convert to using lpfc_rq_buf_free().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when lpfc_nvmet_mrq is 0 it could mean 2 different things
depending on when its looked at. If at module load time it specifies the
default number of hardware queues to allocate, with 0 meaning default to
the number of CPUs. But post module load, a value of zero means to disable
mrq use.
Changed the driver so that enablement of mrq is based on whether nvme
target mode is enabled or not. When enabled, mrq is enabled. Thus, the
cfg_nvemt_mrq field only specifies the number of mrq queues to enable, with
0 defaulting to the number of cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under circustances with high load, the driver is running out of async
receive buffers which may result in one of the following messages:
0:6401 RQE Error x13, posted 226 err_cnt 0: 925c6050 925c604e 925c5d54
or
0:2885 Port Status Event: port status reg 0x81800000,
port smphr reg 0xc000, error 1=0x52004a01, error 2=0x0
The driver is waiting for full io completion before returning receive
buffers to the adapter. There is no need for such a relationship.
Whenever a new command is received from the wire, the driver will have two
contexts - an io context (ctxp) and a receive buffer context. In current
code, the receive buffer context stays 1:1 with the io and won't be
reposted to the hardware until the io completes. There is no need for such
a relationship.
Change the driver so that up on successful handing of the command to the
transport, where the transport has copied what it needed thus the buffer is
returned to the driver, have the driver immediately repost the buffer to
the hardware. If the command cannot be successfully handed to the transport
as transport resources are temporarily busy, have the driver allocate a new
and separate receive buffer and post it to the hardware so that hardware
can continue while the command is queued for the transport.
When an io is complete, the transport returns the io context to the driver,
and the driver may be waiting for more contexts, thus immediately reuse the
io context. In this path, there was a buffer posted when the receive buffer
was queued waiting for an io context so a replacement is not needed in the
new code additions. Thus, exempt this the context reuse case from the
buffer reposting.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debug ktime counters that trace an io were inadvertently not placed in
the common section of an io buffer. Thus, they generate an invalid opcode
error when accessed.
Move the ktime counters into the common area.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A patch in the 12.2.0.0 set caused a new lockdep warning:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.0.0-rc8-next-20190301-dbg+ #1 Not tainted
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&qp->io_buf_list_put_lock)->rlock);
local_irq_disable();
lock(&(&phba->hbalock)->rlock);
lock(&(&qp->io_buf_list_put_lock)->rlock);
<Interrupt>
lock(&(&phba->hbalock)->rlock);
see: https://www.spinics.net/lists/linux-scsi/msg128389.html
In summary, the new patch added taking the io_buf_list_put_lock while under
an irq-disabled hbalock. This created a lock heirarchy dependent upon irq
being disabled, and there are paths that take the io_buf_list_put_lock
without disabling irq.
Looking at the lpfc_io_free routine, which is where the new heirarchy was
introduced, there is no reason to be taking out the hbalock and raising
irq, as the functionality is replaced by the io_buf_list_xxx locks.
Resolve by removing the hbalock/irq calls in lpfc_io_free.
Fixes: 5e5b511d8b ("scsi: lpfc: Partition XRI buffer list across Hardware Queues")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior patch which added support for non-uniform allocation of MSIX
vectors now causes a smatch complaint:
drivers/scsi/lpfc/lpfc_scsi.c:3674 lpfc_scsi_cmd_iocb_cmpl()
error: we previously assumed 'phba->sli4_hba.hdwq' could be
null (see line 3667)
Resolve by removing the unnecessary check for a NULL hdwq table.
Fixes 6a828b0f61: ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are 8 parents, use 0x7
Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190319082611.6215-1-mjourdan@baylibre.com
We want the video decoder clocks to always round to closest. While the
muxes are already using CLK_MUX_ROUND_CLOSEST, the corresponding
CLK_DIVIDER_ROUND_CLOSEST was forgotten for the dividers.
Fix this by adding the flag to the two vdec dividers.
Fixes: a565242eb9 ("clk: meson: gxbb: add the video decoder clocks")
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190319102537.2043-1-mjourdan@baylibre.com
We need to add the object tree include directory to the include path
for building mdp in order to pick up generated/autoconf.h. Otherwise,
make O=/path/to/objtree breaks.
Fixes: e37c1877ba ("scripts/selinux: modernize mdp")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This version includes support for ISP28XX.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for Secure flash update with ISP28xx.
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Includes the following:
- correction to 27xx image status struct;
- factoring of 27xx image status validating routines to make common;
- image status generation compare that works across zero wrap;
- bsg interface to report current active images (as loaded by driver).
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce stack space on each fwdt routine by eliminating local variable reg.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch cleans up and fixes firmware dump template processing. These
changes are added to support newer features for ISP27XX/ISP28XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes following changes to flash access routines:
- update return type for read_optrom
- use void instead of uint32_t * for buffer parameter in read
and write optrom routines
- fix flash/nvram addressing
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds multipe firmware dump template and segments support for
ISP27XX/28XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does following:
- Clean up NVRAM code.
- Optimizes reading of primary/secondary flash image validation.
- Remove 0xff mask and make correct width in FLT structure.
- Use endian macros to assign static fields in fwdump header.
- Correct fdwt checksum calculation.
- Simplify ql_dump_buffer() interface usage.
- Add endianizers to 27xx firmware image validator.
- fixes compiler warnings for big endian architecture.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes reported speed for min_link and max_supported speed. Also
rename sysfs nodes link_speed and max_supported to be consistent with
{min|max}_suuported_speed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds sysfs node for serdes_version and also cleans up port_speed
display.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds PCI device ID ISP28XX for Gen7 support. Also signature
determination for primary/secondary flash image for ISP27XX/28XX is aded as
part of Gen7 support.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes qla27xx_dump_{mpi|ram} api for ISP27XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes FW default template as there will never be case where
the default template would be invoked.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds new sysfs node to display firmware attributes and port
number.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
turbostat failed to return a non-zero exit status even though the
supplied command (turbostat <command>) failed. Currently when turbostat
forks a command it returns zero instead of the actual exit status of the
command. Modify the code to return the exit status.
Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix sparse warning:
drivers/base/swnode.c:475:22: warning: symbol 'software_node_get_parent' was not declared. Should it be static?
drivers/base/swnode.c:484:22: warning: symbol 'software_node_get_next_child' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
My commit 26a7b54731 ("mt76x02: set protection according to ht
operation element") enabled by default RTS/CTS protection for OFDM
and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non
0xffff by initvals and .set_rts_threshold callback is not called by
mac80211 on initialization, only on user request or during
ieee80211_reconfig() (suspend/resuem or restart_hw).
Enabling RTS/CTS cause some problems when sending probe request
frames by hcxdumptool penetration tool, but I expect it can cause
other issues on different scenarios.
Restore previous setting of RTS/CTS being disabled by default for
OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff.
Fixes: 26a7b54731 ("mt76x02: set protection according to ht operation element")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled.
The function that works on all architectures is hweight8().
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since some USB device IDs are duplicated between mt7601u and mt76x0u
devices, check chip version on probe and return error if not match
0x7601.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not mt7601u device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Always init the tp/ip fields of bma in xfs_bmapi_write so that the
bmapi_finish at the bottom never trips over null transaction or inode
pointers.
Coverity-id: 1443964
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
In xchk_btree_check_owner, we can be passed a null buffer pointer. This
should only happen for the root of a root-in-inode btree type, but we
should program defensively in case the btree cursor state ever gets
screwed up and we get a null buffer anyway.
Coverity-id: 1438713
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Make sure scrub's dabtree iterator function checks that we're not
going deeper in the stack than our cursor permits.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
There is no usage of 'nr_expired'.
The 'nr_expired' was introduced by commit 1d9bd5161b ("blk-mq: replace
timeout synchronization with a RCU and generation based scheme"). Its usage
was removed since commit 12f5b93145 ("blk-mq: Remove generation
seqeunce").
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When doing long term recording and waiting for some event to snapshot
on, we often only care about the last minute or so.
The --switch-output command line option supports rotating the perf.data
file when the size exceeds a threshold. But the disk would still be
filled with unnecessary old files.
Add a new option to only keep a number of rotated files, so that the
disk space usage can be limited.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20190314225002.30108-3-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-y5u2lik0ragt4vlktz6qc9ks@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When a filter is specified on the command line, filter the metrics too.
Before:
% perf list foo
List of pre-defined events (to be used in -e):
Metric Groups:
DSB:
DSB_Coverage
[Fraction of Uops delivered by the DSB (aka Decoded Icache; or Uop Cache)]
... more metrics ...
After:
% perf list foo
List of pre-defined events (to be used in -e):
Metric Groups:
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20190314225002.30108-1-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-1y8oi2s8c4jhjtykgs5zvda1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
HiSilicon Taishan v110 CPUs didn't implement CSV3 field of the
ID_AA64PFR0_EL1 and are not susceptible to Meltdown, so whitelist
the MIDR in kpti_safe_list[] table.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangshaokun <zhangshaokun@hisilicon.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Adding the MIDR encodings for HiSilicon Taishan v110 CPUs,
which is used in Kunpeng ARM64 server SoCs. TSV110 is the
abbreviation of Taishan v110.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangshaokun <zhangshaokun@hisilicon.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The ARM64 implements the save_stack_trace_regs function, but it is
unusable for any diagnostic tooling compiled as a kernel module due
the missing EXPORT_SYMBOL_GPL for the function. Export
save_stack_trace_regs() to align with other architectures such as
s390, openrisc, and powerpc. This is similar to the ARM64 export of
save_stack_trace_tsk() added in git commit e27c7fa015.
Signed-off-by: William Cohen <wcohen@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fujitsu erratum 010001 applies to A64FX v0r0 and v1r0, and we try to
handle either by masking MIDR with MIDR_FUJITSU_ERRATUM_010001_MASK
before comparing it to MIDR_FUJITSU_ERRATUM_010001.
Unfortunately, MIDR_FUJITSU_ERRATUM_010001 is constructed incorrectly
using MIDR_VARIANT(), which is intended to extract the variant field
from MIDR_EL1, rather than generate the field in-place. This results in
MIDR_FUJITSU_ERRATUM_010001 being all-ones, and we only match A64FX
v0r0.
This patch uses MIDR_CPU_VAR_REV() to generate an in-place mask for the
variant field, ensuring the we match both v0r0 and v1r0.
Fixes: 3e32131abc ("arm64: Add workaround for Fujitsu A64FX erratum 010001")
Reported-by: "Okamoto, Takayuki" <tokamoto@jp.fujitsu.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: fixed the patch author]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is a race condition that could happen if hid_debug_rdesc_show()
is running while hdev is in the process of going away (device removal,
system suspend, etc) which could result in NULL pointer dereference:
BUG: unable to handle kernel paging request at 0000000783316040
CPU: 1 PID: 1512 Comm: getevent Tainted: G U O 4.19.20-quilt-2e5dc0ac-00029-gc455a447dd55 #1
RIP: 0010:hid_dump_device+0x9b/0x160
Call Trace:
hid_debug_rdesc_show+0x72/0x1d0
seq_read+0xe0/0x410
full_proxy_read+0x5f/0x90
__vfs_read+0x3a/0x170
vfs_read+0xa0/0x150
ksys_read+0x58/0xc0
__x64_sys_read+0x1a/0x20
do_syscall_64+0x55/0x110
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Grab driver_input_lock to make sure the input device exists throughout the
whole process of dumping the rdesc.
[jkosina@suse.cz: update changelog a bit]
Signed-off-by: he, bo <bo.he@intel.com>
Signed-off-by: "Zhang, Jun" <jun.zhang@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
