Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/i3c/master/dw-i3c-master.c: In function ‘dw_i3c_master_bus_init’:
drivers/i3c/master/dw-i3c-master.c:603:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret)
^
drivers/i3c/master/dw-i3c-master.c:605:2: note: here
case I3C_BUS_MODE_PURE:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e88975ca37 ("ath10k: dump tx stats in rate table format")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The NSS data is updated incorrectly in the tx stats as the array
indexing starts from zero.
Fix the incorrect updation of NSS data in tx_stats by taking into
consideration the array index starting from zero.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c: In function '_rtl92s_firmware_downloadcode':
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c:139:17: warning:
variable 'seg_ptr' set but not used [-Wunused-but-set-variable]
It's not used after commit 59ae1d127a ("networking: introduce and use
skb_put_data()")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c: In function '_rtl8723e_dm_bt_coexist_2_ant':
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c:1408:5: warning:
variable 'bt_retry_cnt' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c: In function 'rtl8723be_dm_check_edca_turbo':
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:998:7: warning:
variable 'b_last_is_cur_rdlstate' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to of_find_node_by_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/wireless/mediatek/mt76/eeprom.c:58:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:61:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:67:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:70:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:72:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following types of blank line problems are reported:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following problems were found:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum declarations
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The problems filed include the following:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The types of problems fixed are as follows:
WARNING: Missing a blank line after declarations
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The errors consist of multiple blank lines, and a missing blank line
after the declarations.
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The instances where statement continuations are improperly aligned have
been fixed.
There are no changes to generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of problems with block comments.
These changes do not affect the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl report problems in wifi.h where spaces are missing, as well
as extraneous spaces.
There are no changes in the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Alter the AFS automounting code to create and modify an fs_context struct
when parameterising a new mount triggered by an AFS mountpoint rather than
constructing device name and option strings.
Also remove the cell=, vol= and rwpath options as they are then redundant.
The reason they existed is because the 'device name' may be derived
literally from a mountpoint object in the filesystem, so default cell and
parent-type information needed to be passed in by some other method from
the automount routines. The vol= option didn't end up being used.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric W. Biederman <ebiederm@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add fs_context support to the AFS filesystem, converting the parameter
parsing to store options there.
This will form the basis for namespace propagation over mountpoints within
the AFS model, thereby allowing AFS to be used in containers more easily.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add some logging to the core users of the fs_context log so that
information can be extracted from them as to the reason for failure.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Implement the ability for filesystems to log error, warning and
informational messages through the fs_context. In the future, these will
be extractable by userspace by reading from an fd created by the fsopen()
syscall.
Error messages are prefixed with "e ", warnings with "w " and informational
messages with "i ".
In the future, inside the kernel, formatted messages will be malloc'd but
unformatted messages will not copied if they're either in the core .rodata
section or in the .rodata section of the filesystem module pinned by
fs_context::fs_type. The messages will only be good till the fs_type is
released.
Note that the logging object will be shared between duplicated fs_context
structures. This is so that such as NFS which do a mount within a mount
can get at least some of the errors from the inner mount.
Five logging functions are provided for this:
(1) void logfc(struct fs_context *fc, const char *fmt, ...);
This logs a message into the context. If the buffer is full, the
earliest message is discarded.
(2) void errorf(fc, fmt, ...);
This wraps logfc() to log an error.
(3) void invalf(fc, fmt, ...);
This wraps errorf() and returns -EINVAL for convenience.
(4) void warnf(fc, fmt, ...);
This wraps logfc() to log a warning.
(5) void infof(fc, fmt, ...);
This wraps logfc() to log an informational message.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The kern_mount_data() isn't used any more so remove it.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert the hugetlbfs to use the fs_context during mount.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make the cpuset filesystem use the filesystem context. This is potentially
tricky as the cpuset fs is almost an alias for the cgroup filesystem, but
with some special parameters.
This can, however, be handled by setting up an appropriate cgroup
filesystem and returning the root directory of that as the root dir of this
one.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make kernfs support superblock creation/mount/remount with fs_context.
This requires that sysfs, cgroup and intel_rdt, which are built on kernfs,
be made to support fs_context also.
Notes:
(1) A kernfs_fs_context struct is created to wrap fs_context and the
kernfs mount parameters are moved in here (or are in fs_context).
(2) kernfs_mount{,_ns}() are made into kernfs_get_tree(). The extra
namespace tag parameter is passed in the context if desired
(3) kernfs_free_fs_context() is provided as a destructor for the
kernfs_fs_context struct, but for the moment it does nothing except
get called in the right places.
(4) sysfs doesn't wrap kernfs_fs_context since it has no parameters to
pass, but possibly this should be done anyway in case someone wants to
add a parameter in future.
(5) A cgroup_fs_context struct is created to wrap kernfs_fs_context and
the cgroup v1 and v2 mount parameters are all moved there.
(6) cgroup1 parameter parsing error messages are now handled by invalf(),
which allows userspace to collect them directly.
(7) cgroup1 parameter cleanup is now done in the context destructor rather
than in the mount/get_tree and remount functions.
Weirdies:
(*) cgroup_do_get_tree() calls cset_cgroup_from_root() with locks held,
but then uses the resulting pointer after dropping the locks. I'm
told this is okay and needs commenting.
(*) The cgroup refcount web. This really needs documenting.
(*) cgroup2 only has one root?
Add a suggestion from Thomas Gleixner in which the RDT enablement code is
placed into its own function.
[folded a leak fix from Andrey Vagin]
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tejun Heo <tj@kernel.org>
cc: Li Zefan <lizefan@huawei.com>
cc: Johannes Weiner <hannes@cmpxchg.org>
cc: cgroups@vger.kernel.org
cc: fenghua.yu@intel.com
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
pass it fs_context instead of fs_type/flags/root triple, have
it return int instead of dentry and make it deal with setting
fc->root.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Note that this reference is *NOT* contributing to refcount of
cgroup_root in question and is valid only until cgroup_do_mount()
returns.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[again, carved out of patch by dhowells]
[NB: we probably want to handle "source" in parse_param here]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Store the results in cgroup_fs_context. There's a nasty twist caused
by the enabling/disabling subsystems - we can't do the checks sensitive
to that until cgroup_mutex gets grabbed. Frankly, these checks are
complete bullshit (e.g. all,none combination is accepted if all subsystems
are disabled; so's cpusets,none and all,cpusets when cpusets is disabled,
etc.), but touching that would be a userland-visible behaviour change ;-/
So we do parsing in ->parse_monolithic() and have the consistency checks
done in check_cgroupfs_options(), with the latter called (on already parsed
options) from cgroup1_get_tree() and cgroup1_reconfigure().
Freeing the strdup'ed strings is done from fs_context destructor, which
somewhat simplifies the life for cgroup1_{get_tree,reconfigure}().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Unfortunately, cgroup is tangled into kernfs infrastructure.
To avoid converting all kernfs-based filesystems at once,
we need to untangle the remount part of things, instead of
having it go through kernfs_sop_remount_fs(). Fortunately,
it's not hard to do.
This commit just gets cgroup/cgroup1 to use fs_context to
deliver options on mount and remount paths. Parsing those
is going to be done in the next commits; for now we do
pretty much what legacy case does.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert the mqueue filesystem to use the filesystem context stuff.
Notes:
(1) The relevant ipc namespace is selected in when the context is
initialised (and it defaults to the current task's ipc namespace).
The caller can override this before calling vfs_get_tree().
(2) Rather than simply calling kern_mount_data(), mq_init_ns() and
mq_internal_mount() create a context, adjust it and then do the rest
of the mount procedure.
(3) The lazy mqueue mounting on creation of a new namespace is retained
from a previous patch, but the avoidance of sget() if no superblock
yet exists is reverted and the superblock is again keyed on the
namespace pointer.
Yes, there was a performance gain in not searching the superblock
hash, but it's only paid once per ipc namespace - and only if someone
uses mqueue within that namespace, so I'm not sure it's worth it,
especially as calling sget() allows avoidance of recursion.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add fs_context support to procfs.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Move proc_fill_super() to fs/proc/root.c as that's where the other
superblock stuff is.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com>
cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
new primitive: vfs_dup_fs_context(). Comes with fs_context
method (->dup()) for copying the filesystem-specific parts
of fs_context, along with LSM one (->fs_context_dup()) for
doing the same to LSM parts.
[needs better commit message, and change of Author:, anyway]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
the former is an analogue of mount_{single,nodev} for use in
->get_tree() instances, the latter - analogue of sget() for the
same.
These are fairly similar to the originals, but the callback signature
for sget_fc() is different from sget() ones, so getting bits and
pieces shared would be too convoluted; we might get around to that
later, but for now let's just remember to keep them in sync. They
do live next to each other, and changes in either won't be hard
to spot.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[AV - unfuck kern_mount_data(); we want non-NULL ->mnt_ns on long-living
mounts]
[AV - reordering fs/namespace.c is badly overdue, but let's keep it
separate from that series]
[AV - drop simple_pin_fs() change]
[AV - clean vfs_kern_mount() failure exits up]
Implement a filesystem context concept to be used during superblock
creation for mount and superblock reconfiguration for remount.
The mounting procedure then becomes:
(1) Allocate new fs_context context.
(2) Configure the context.
(3) Create superblock.
(4) Query the superblock.
(5) Create a mount for the superblock.
(6) Destroy the context.
Rather than calling fs_type->mount(), an fs_context struct is created and
fs_type->init_fs_context() is called to set it up. Pointers exist for the
filesystem and LSM to hang their private data off.
A set of operations has to be set by ->init_fs_context() to provide
freeing, duplication, option parsing, binary data parsing, validation,
mounting and superblock filling.
Legacy filesystems are supported by the provision of a set of legacy
fs_context operations that build up a list of mount options and then invoke
fs_type->mount() from within the fs_context ->get_tree() operation. This
allows all filesystems to be accessed using fs_context.
It should be noted that, whilst this patch adds a lot of lines of code,
there is quite a bit of duplication with existing code that can be
eliminated should all filesystems be converted over.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Put security flags, such as SECURITY_LSM_NATIVE_LABELS, into the filesystem
context so that the filesystem can communicate them to the LSM more easily.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Implement the new mount API LSM hooks for SELinux. At some point the old
hooks will need to be removed.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Paul Moore <paul@paul-moore.com>
cc: Stephen Smalley <sds@tycho.nsa.gov>
cc: selinux@tycho.nsa.gov
cc: linux-security-module@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add LSM hooks for use by the new mount API and filesystem context code.
This includes:
(1) Hooks to handle allocation, duplication and freeing of the security
record attached to a filesystem context.
(2) A hook to snoop source specifications. There may be multiple of these
if the filesystem supports it. They will to be local files/devices if
fs_context::source_is_dev is true and will be something else, possibly
remote server specifications, if false.
(3) A hook to snoop superblock configuration options in key[=val] form.
If the LSM decides it wants to handle it, it can suppress the option
being passed to the filesystem. Note that 'val' may include commas
and binary data with the fsopen patch.
(4) A hook to perform validation and allocation after the configuration
has been done but before the superblock is allocated and set up.
(5) A hook to transfer the security from the context to a newly created
superblock.
(6) A hook to rule on whether a path point can be used as a mountpoint.
These are intended to replace:
security_sb_copy_data
security_sb_kern_mount
security_sb_mount
security_sb_set_mnt_opts
security_sb_clone_mnt_opts
security_sb_parse_opts_str
[AV -- some of the methods being replaced are already gone, some of the
methods are not added for the lack of need]
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-security-module@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Because the new API passes in key,value parameters, match_token() cannot be
used with it. Instead, provide three new helpers to aid with parsing:
(1) fs_parse(). This takes a parameter and a simple static description of
all the parameters and maps the key name to an ID. It returns 1 on a
match, 0 on no match if unknowns should be ignored and some other
negative error code on a parse error.
The parameter description includes a list of key names to IDs, desired
parameter types and a list of enumeration name -> ID mappings.
[!] Note that for the moment I've required that the key->ID mapping
array is expected to be sorted and unterminated. The size of the
array is noted in the fsconfig_parser struct. This allows me to use
bsearch(), but I'm not sure any performance gain is worth the hassle
of requiring people to keep the array sorted.
The parameter type array is sized according to the number of parameter
IDs and is indexed directly. The optional enum mapping array is an
unterminated, unsorted list and the size goes into the fsconfig_parser
struct.
The function can do some additional things:
(a) If it's not ambiguous and no value is given, the prefix "no" on
a key name is permitted to indicate that the parameter should
be considered negatory.
(b) If the desired type is a single simple integer, it will perform
an appropriate conversion and store the result in a union in
the parse result.
(c) If the desired type is an enumeration, {key ID, name} will be
looked up in the enumeration list and the matching value will
be stored in the parse result union.
(d) Optionally generate an error if the key is unrecognised.
This is called something like:
enum rdt_param {
Opt_cdp,
Opt_cdpl2,
Opt_mba_mpbs,
nr__rdt_params
};
const struct fs_parameter_spec rdt_param_specs[nr__rdt_params] = {
[Opt_cdp] = { fs_param_is_bool },
[Opt_cdpl2] = { fs_param_is_bool },
[Opt_mba_mpbs] = { fs_param_is_bool },
};
const const char *const rdt_param_keys[nr__rdt_params] = {
[Opt_cdp] = "cdp",
[Opt_cdpl2] = "cdpl2",
[Opt_mba_mpbs] = "mba_mbps",
};
const struct fs_parameter_description rdt_parser = {
.name = "rdt",
.nr_params = nr__rdt_params,
.keys = rdt_param_keys,
.specs = rdt_param_specs,
.no_source = true,
};
int rdt_parse_param(struct fs_context *fc,
struct fs_parameter *param)
{
struct fs_parse_result parse;
struct rdt_fs_context *ctx = rdt_fc2context(fc);
int ret;
ret = fs_parse(fc, &rdt_parser, param, &parse);
if (ret < 0)
return ret;
switch (parse.key) {
case Opt_cdp:
ctx->enable_cdpl3 = true;
return 0;
case Opt_cdpl2:
ctx->enable_cdpl2 = true;
return 0;
case Opt_mba_mpbs:
ctx->enable_mba_mbps = true;
return 0;
}
return -EINVAL;
}
(2) fs_lookup_param(). This takes a { dirfd, path, LOOKUP_EMPTY? } or
string value and performs an appropriate path lookup to convert it
into a path object, which it will then return.
If the desired type was a blockdev, the type of the looked up inode
will be checked to make sure it is one.
This can be used like:
enum foo_param {
Opt_source,
nr__foo_params
};
const struct fs_parameter_spec foo_param_specs[nr__foo_params] = {
[Opt_source] = { fs_param_is_blockdev },
};
const char *char foo_param_keys[nr__foo_params] = {
[Opt_source] = "source",
};
const struct constant_table foo_param_alt_keys[] = {
{ "device", Opt_source },
};
const struct fs_parameter_description foo_parser = {
.name = "foo",
.nr_params = nr__foo_params,
.nr_alt_keys = ARRAY_SIZE(foo_param_alt_keys),
.keys = foo_param_keys,
.alt_keys = foo_param_alt_keys,
.specs = foo_param_specs,
};
int foo_parse_param(struct fs_context *fc,
struct fs_parameter *param)
{
struct fs_parse_result parse;
struct foo_fs_context *ctx = foo_fc2context(fc);
int ret;
ret = fs_parse(fc, &foo_parser, param, &parse);
if (ret < 0)
return ret;
switch (parse.key) {
case Opt_source:
return fs_lookup_param(fc, &foo_parser, param,
&parse, &ctx->source);
default:
return -EINVAL;
}
}
(3) lookup_constant(). This takes a table of named constants and looks up
the given name within it. The table is expected to be sorted such
that bsearch() be used upon it.
Possibly I should require the table be terminated and just use a
for-loop to scan it instead of using bsearch() to reduce hassle.
Tables look something like:
static const struct constant_table bool_names[] = {
{ "0", false },
{ "1", true },
{ "false", false },
{ "no", false },
{ "true", true },
{ "yes", true },
};
and a lookup is done with something like:
b = lookup_constant(bool_names, param->string, -1);
Additionally, optional validation routines for the parameter description
are provided that can be enabled at compile time. A later patch will
invoke these when a filesystem is registered.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The call to ieee80211_probereq_get can return NULL if a skb allocation
fails, so add a null pointer check and free an earlier skb on the error
exit return path.
Fixes: 7fdcb8e126 ("rsi: add support for hardware scan offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the card was removed in suspended state and a new one was inserted,
print a debug log when the check detects that it's not the old card.
Signed-off-by: hongjiefang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
