It clarifies that the DMA description pointer returned by
`dmaengine_prep_*` function should not be used after submission.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Implement --affinity=node|cpu option for the record mode defaulting
to system affinity mask bouncing.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/083f5422-ece9-10dd-8305-bf59c860f10f@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As can be seen by clicking around the timeline on web.archive.org[1],
there were no -git patches/tarballs on kernel.org since release 3.1.
[1]: https://web.archive.org/web/20111103073843/http://www.kernel.org/
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
AFAIK we never had a isa_virt_to_phys, it always was
isa_virt_to_bus.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There's no reason to freeze queue and remove scheduler
if there's no scheduler already.
Signed-off-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's no reason to set wbt min lat and freeze request queue
if current value is the same.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes a race condition where a write is mapped to the last
sectors of a line. The write is synced to the device but the L2P is not
updated yet. When the line is garbage collected before the L2P update
is performed, the sectors are ignored by the GC logic and the line is
freed before all sectors are moved. When the L2P is finally updated, it
contains a mapping to a freed line, subsequent reads of the
corresponding LBAs fail.
This patch introduces a per line counter specifying the number of
sectors that are synced to the device but have not been updated in the
L2P. Lines with a counter of greater than zero will not be selected
for GC.
Signed-off-by: Heiner Litz <hlitz@ucsc.edu>
Reviewed-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In order to respect mw_cuinits, pblk's write buffer maintains a
backpointer to protect data not yet persisted; when writing to the write
buffer, this backpointer defines a threshold that pblk's rate-limiter
enforces.
On small PU configurations, the following scenarios might take place: (i)
the threshold is larger than the write buffer and (ii) the threshold is
smaller than the write buffer, but larger than the maximun allowed
split bio - 256KB at this moment (Note that writes are not always
split - we only do this when we the size of the buffer is smaller
than the buffer). In both cases, pblk's rate-limiter prevents the I/O to
be written to the buffer, thus stalling.
This patch fixes the original backpointer implementation by considering
the threshold both on buffer creation and on the rate-limiters path,
when bio_split is triggered (case (ii) above).
Fixes: 766c8ceb16 ("lightnvm: pblk: guarantee that backpointer is respected on writer stall")
Signed-off-by: Javier González <javier@javigon.com>
Reviewed-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
pblk stripes writes of minimal write size across all non-offline chunks
in a line, which means that the maximum write pointer delta should not
exceed the minimal write size.
Extend the line write pointer balance check to cover this case, and
ignore the offline chunk wps.
This will render us a warning during recovery if something unexpected
has happened to the chunk write pointers (i.e. powerloss, a spurious
chunk reset, ..).
Reported-by: Zhoujie Wu <zjwu@marvell.com>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As the comment block in include/trace/define_trace.h says,
TRACE_INCLUDE_PATH should be a relative path to the define_trace.h
../../drivers/lightnvm is the correct relative path.
../../../drivers/lightnvm is working by coincidence because the top
Makefile adds -I$(srctree)/arch/$(SRCARCH)/include as a header
search path, but we should not rely on it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sparse complains about using strict data types:
drivers/lightnvm/pblk-read.c:254:43: warning: incorrect type in assignment (different base types)
drivers/lightnvm/pblk-read.c:254:43: expected restricted __le64 <noident>
drivers/lightnvm/pblk-read.c:254:43: got unsigned long long [unsigned] [usertype] <noident>
drivers/lightnvm/pblk-read.c:255:29: warning: cast from restricted __le64
drivers/lightnvm/pblk-read.c:268:29: warning: cast from restricted __le64
drivers/lightnvm/pblk-read.c:328:41: warning: incorrect type in assignment (different base types)
drivers/lightnvm/pblk-read.c:328:41: expected restricted __le64 <noident>
drivers/lightnvm/pblk-read.c:328:41: got unsigned long long [unsigned] [usertype] <noident>
In the code it seems explicit that lba_list_mem and lba_list_media members
of struct pblk_pr_ctx are used on CPU side, which means they should not be
of strict types.
Change types of lba_list_mem and lba_list_media members to be u64.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As chunk metadata is allocated using vmalloc, we need to free it
using vfree.
Fixes: 090ee26fd5 ("lightnvm: use internal allocation for chunk log page")
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
pblk_line_meta_free might sleep (it can end up calling vfree, depending
on how we allocate lba lists), and this can lead to a BUG()
if we wake up on a different cpu and release the lock.
As there is no point of grabbing the free lock when pblk has shut down,
remove the lock.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The original MODULE_LICENSE string for kernel modules licensed under the
GPL v2 (only / or later) was simply "GPL", which was - and still is -
completely sufficient for the purpose of module loading and checking
whether the module is free software or proprietary.
In January 2003 this was changed with commit 3344ea3ad4b7 ("[PATCH]
MODULE_LICENSE and EXPORT_SYMBOL_GPL support"). This commit can be found in
the history git repository which holds the 1:1 import of Linus' bitkeeper
repository:
https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/?id=3344ea3ad4b7c302c846a680dbaeedf96ed45c02
The main intention of the patch was to refuse linking proprietary modules
against symbols exported with EXPORT_SYMBOL_GPL() at module load time.
As a completely undocumented side effect it also introduced the distinction
between "GPL" and "GPL v2" MODULE_LICENSE() strings:
* "GPL" [GNU Public License v2 or later]
* "GPL v2" [GNU Public License v2]
* "GPL and additional rights" [GNU Public License v2 rights and more]
* "Dual BSD/GPL" [GNU Public License v2
* or BSD license choice]
* "Dual MPL/GPL" [GNU Public License v2
* or Mozilla license choice]
This distinction was and still is wrong in several aspects:
1) It broke all modules which were using the "GPL" string in the
MODULE_LICENSE() already and were licensed under GPL v2 only.
A quick license scan over the tree at that time shows that at least 480
out of 1484 modules have been affected by this change back then. The
number is probably way higher as this was just a quick check for
clearly identifiable license information.
There was exactly ONE instance of a "GPL v2" module license string in
the kernel back then - drivers/net/tulip/xircom_tulip_cb.c which
otherwise had no license information at all. There is no indication
that the change above is any way related to this driver. The change
happend with the 2.4.11 release which was on Oct. 9 2001 - so quite
some time before the above commit. Unfortunately there is no trace on
the intertubes to any discussion of this.
2) The dual licensed strings became ill defined as well because following
the "GPL" vs. "GPL v2" distinction all dual licensed (or additional
rights) MODULE_LICENSE strings would either require those dual licensed
modules to be licensed under GPL v2 or later or just be unspecified for
the dual licensing case. Neither choice is coherent with the GPL
distinction.
Due to the lack of a proper changelog and no real discussion on the patch
submission other than a few implementation details, it's completely unclear
why this distinction was introduced at all. Other than the comment in the
module header file exists no documentation for this at all.
From a license compliance and license scanning POV this distinction is a
total nightmare.
As of 5.0-rc2 2873 out of 9200 instances of MODULE_LICENSE() strings are
conflicting with the actual license in the source code (either SPDX or
license boilerplate/reference). A comparison between the scan of the
history tree and a scan of current Linus tree shows to the extent that the
git rename detection over Linus tree grafted with the history tree is
halfways complete that almost none of the files which got broken in 2003
have been cleaned up vs. the MODULE_LICENSE string. So subtracting those
480 known instances from the conflicting 2800 of today more than 25% of the
module authors got it wrong and it's a high propability that a large
portion of the rest just got it right by chance.
There is no value for the module loader to convey the detailed license
information as the only decision to be made is whether the module is free
software or not.
The "and additional rights", "BSD" and "MPL" strings are not conclusive
license information either. So there is no point in trying to make the GPL
part conclusive and exact. As shown above it's already non conclusive for
dual licensing and incoherent with a large portion of the module source.
As an unintended side effect this distinction causes a major headache for
license compliance, license scanners and the ongoing effort to clean up the
license mess of the kernel.
Therefore remove the well meant, but ill defined, distinction between "GPL"
and "GPL v2" and document that:
- "GPL" and "GPL v2" both express that the module is licensed under GPLv2
(without a distinction of 'only' and 'or later') and is therefore kernel
license compliant.
- None of the MODULE_LICENSE strings can be used for expressing or
determining the exact license
- Their sole purpose is to decide whether the module is free software or
not.
Add a MODULE_LICENSE subsection to the license rule documentation as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Joe Perches <joe@perches.com>
[jc: Did s/merily/merely/ ]
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
When mac80211 requests the low level driver to stop an ongoing
Tx aggregation, the low level driver is expected to call
ieee80211_stop_tx_ba_cb_irqsafe() to indicate that it is ready
to stop the session. The callback in turn schedules a worker
to complete the session tear down, which in turn also handles
the relevant state for the intermediate Tx queue.
However, as this flow in asynchronous, the intermediate queue
should be stopped and not continue servicing frames, as in
such a case frames that are dequeued would be marked as part
of an aggregation, although the aggregation is already been
stopped.
Fix this by stopping the intermediate Tx queue, before
calling the low level driver to stop the Tx aggregation.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's possible that the caller of cfg80211_classify8021d() uses the
value to index an array, like mac80211 in ieee80211_downgrade_queue().
Prevent speculation on the return value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without recording the netlink port ID, we cannot return the
results or complete messages to userspace, nor will we be
able to abort if the socket is closed, so clearly we need
to fill the value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix FTM per burst maximum value from 15 to 31
(The maximal bits that represents that number in the frame
is 5 hence a maximal value of 31)
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a driver does any significant activity in its ibss_join method,
then it will very well expect that to be called during restart,
before any stations are added. Do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni reports that in some cases it is possible that getting
disconnected (or stopping AP, after previous patches) results
in further operations hitting the window within the regulatory
core restoring the regdomain to the defaults. The reason for
this is that we have to call out to CRDA or otherwise do some
asynchronous work, and thus can't do the restore atomically.
However, we've previously seen all the data we need to do the
restore, so we can hang on to that data and use it later for
the restore. This makes the whole thing happen within a single
locked section and thus atomic.
However, we can't *always* do this - there are unfortunately
cases where the restore needs to re-request, because this is
also used (abused?) as an error recovery process, so make the
new behaviour optional and only use it when doing a regular
restore as described above.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Gigabyte X299 DESIGNARE EX motherboard has one PCIe root port that is
connected to an Alpine Ridge Thunderbolt controller. This port has slot
implemented bit set in the config space but other than that it is not
hotplug capable in the sense we are expecting in Linux (it has
dev->is_hotplug_bridge set to 0):
00:1c.4 PCI bridge: Intel Corporation 200 Series PCH PCI Express Root Port #5
Bus: primary=00, secondary=05, subordinate=46, sec-latency=0
Memory behind bridge: 78000000-8fffffff [size=384M]
Prefetchable memory behind bridge: 00003800f8000000-00003800ffffffff [size=128M]
...
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
...
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #8, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState+
This system is using ACPI based hotplug to notify the OS that it needs to
rescan the PCI bus (ACPI hotplug).
If there is nothing connected in any of the Thunderbolt ports the root port
will not have any runtime PM active children and is thus automatically
runtime suspended pretty soon after boot by PCI PM core. Now, when a
device is connected the BIOS SMI handler responsible for enumerating newly
added devices is not able to find anything because the port is in D3.
Prevent this from happening by blacklisting PCI power management of this
particular Gigabyte system.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202031
Reported-by: Kedar A Dongre <kedar.a.dongre@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Presently, when ntb_transport is used with DMA and the IOMMU turned on,
it fails with errors from the IOMMU such as:
DMAR: DRHD: handling fault status reg 202
DMAR: [DMA Write] Request device [00:04.0] fault addr
381fc0340000 [fault reason 05] PTE Write access is not set
This is because ntb_transport does not map the BAR space with the IOMMU.
To fix this, we map the entire MW region for each QP after we assign
the DMA channel. This prevents needing an extra DMA map in the fast
path.
Link: https://lore.kernel.org/linux-pci/499934e7-3734-1aee-37dd-b42a5d2a2608@intel.com/
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
If NTB peer host crashes or reboots, the NTB transport link will be
down and the MWs of NTB transport will be invalid. But the
ntb_transport_link_cleanup() does not free these invalid MWs. When
the NTB peer host is recovered later, NTB transport link will be
up and the ntb_set_mw() will not reset up MWs. Because the MWs of
NTB transport are invalid, the NTB transport will not work.
We can fix it by freeing MWs when NTB transport link is down, then
the ntb_set_mw() will reset up MWs when NTB transport link is up.
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_map_single already transfers ownership to the device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
User space tools which do automated task placement need information
about AVX-512 usage of tasks, because AVX-512 usage could cause core
turbo frequency drop and impact the running task on the sibling CPU.
The XSAVE hardware structure has bits that indicate when valid state
is present in registers unique to AVX-512 use. Use these bits to
indicate when AVX-512 has been in use and add per-task AVX-512 state
timestamp tracking to context switch.
Well-written AVX-512 applications are expected to clear the AVX-512
state when not actively using AVX-512 registers, so the tracking
mechanism is imprecise and can theoretically miss AVX-512 usage during
context switch. But it has been measured to be precise enough to be
useful under real-world workloads like tensorflow and linpack.
If higher precision is required, suggest user space tools to use the
PMU-based mechanisms in combination.
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: aubrey.li@intel.com
Link: http://lkml.kernel.org/r/20190117183822.31333-1-aubrey.li@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some distibutions and build systems doesn't include 'fold' from
coreutils default.
.../scripts/atomic/atomic-tbl.sh: line 183: fold: command not found
Rework to use 'grep' instead of 'fold' to use a dependency that is
already used a lot in the kernel.
[Mark: rework commit message]
Suggested-by: Will Deacon <will.deacon@arm.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: boqun.feng@gmail.com
Cc: linux-kernel@vger.kernel.rg
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds DRIF{0,1,2,3} pins, groups and functions to the R8A77965
SoC.
Based on a similar patch of the R8A7796 PFC driver
by Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a build-time check, to ensure the register and field widths in
descriptors for config registers with fixed-width fields are sane.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
There are two pin groups for the FSIC SPDIF signal, but the FSIC pin
group array lists only one, and it refers to a nonexistent group.
Fixes: 2ecd4154c9 ("sh-pfc: sh73a0: Add FSI pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The vin1_data18_b pin group itself is present, but it is not listed in
the VIN1 pin group array, and thus cannot be selected.
Fixes: 7dd74bb1f0 ("pinctrl: sh-pfc: r8a7792: Add VIN pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The entry for "scifb2_data_c" in the SCIFB2 pin group array contains a
typo, thus the group cannot be selected.
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The err_rst_reqb, ext_clki, lowpwr, and ref_clko pin groups are present,
but no pinmux functions refer to them, hence they can not be selected.
Fixes: 1e7d5d849c ("sh-pfc: Add emev2 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Current Switchtec's BAR setup registers are limited to 32bits,
corresponding to the maximum MW (memory window) size is <4G.
Increase the MW sizes with the addition of the BAR Setup Extension
Register for the upper 32bits of a 64bits MW size. This increases the MW
range to between 4K and 2^63.
Reported-by: Boris Glimcher <boris.glimcher@emc.com>
Signed-off-by: Paul Selles <paul.selles@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The number of available NT req id mapping table entries per NTB control
register is 512. The driver mistakenly limits the number to 256.
Fix the array size of NT req id mapping table.
Fixes: c082b04c9d ("NTB: switchtec: Add NTB hardware register definitions")
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Switchtec NTB crosslink BARs are 64bit addressed but they are printed as
32bit addressed BARs. Fix debug log to increment the BAR numbers by 2 to
reflect the 64bit address alignment.
Fixes: 0175250182 ("ntb_hw_switchtec: Add initialization code for crosslink")
Signed-off-by: Paul Selles <paul.selles@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When facility.76 MSAX3 is present for the guest we must issue a validity
interception if the CRYCBD is not valid.
The bit CRYCBD.31 is an effective field and tested at each guest level
and has for effect to mask the facility.76
It follows that if CRYCBD.31 is clear and AP is not in use we do not
have to test the CRYCBD validatity even if facility.76 is present in the
host.
Fixes: 6ee7409820 ("KVM: s390: vsie: allow CRYCB FORMAT-0")
Cc: stable@vger.kernel.org
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reported-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1549876849-32680-1-git-send-email-pmorel@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
It clarifies that the DMA description pointer returned by
`dmaengine_prep_*` function should not be used after submission.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix markup warning: insert a blank line before the hint.
Documentation/driver-api/dmaengine/dmatest.rst:63: WARNING: Unexpected indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Thomas noticed that the new arch/x86/include/asm/cpu_device_id.h header is
a train-wreck that didn't incorporate review feedback like not using __u8
in kernel-only headers.
While at it also fix all the *other* problems this header has:
- Use canonical names for the header guards. It's inexplicable why a non-standard
guard was used.
- Don't define the header guard to 1. Plus annotate the closing #endif as done
absolutely every other header. Again, an inexplicable source of noise.
- Move the kernel API calls provided by this header next to each other, there's
absolutely no reason to have them spread apart in the header.
- Align the INTEL_CPU_DESC() macro initializations vertically, this is easier to
read and it's also the canonical style.
- Actually name the macro arguments properly: instead of 'mod, step, rev',
spell out 'model, stepping, revision' - it's not like we have a lack of
characters in this header.
- Actually make arguments macro-safe - again it's inexplicable why it wasn't
done properly to begin with.
Quite amazing how many problems a 41 lines header can contain.
This kind of code quality is unacceptable, and it slipped through the
review net of 2 developers and 2 maintainers, including myself, until
Thomas noticed it. :-/
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Starting from opregion version 2.1 (roughly corresponding to ICL+) the
RVDA field is relative from the beginning of opregion, not absolute
address.
Fix the error path while at it.
v2: Make relative vs. absolute conditional on the opregion version,
bumped for the purpose. Turned out there are machines relying on
absolute RVDA in the wild.
v3: Fix the version checks
Fixes: 04ebaadb9f ("drm/i915/opregion: handle VBT sizes bigger than 6 KB")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208184254.24123-2-jani.nikula@intel.com
The u32 version field encodes major, minor, revision and reserved. We've
basically been checking for any non-zero version.
Add opregion version logging while at it.
v2: Fix the fix of the version check
Fixes: 04ebaadb9f ("drm/i915/opregion: handle VBT sizes bigger than 6 KB")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208184254.24123-1-jani.nikula@intel.com
If we allocate while iterating the rbtree of active nodes, we may hit
the shrinker and so retire the i915_active, reaping the rbtree. Modifying
the rbtree as we iterate is not good behaviour, so acquire the
i915_active first to keep the tree intact whenever we allocate.
Fixes: a42375af0a ("drm/i915: Release the active tracker tree upon idling")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208134704.23039-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
