Having both a function and a function pointer member with the same
name (iscsit_release_cmd) is confusing. Hence rename the function pointer
member.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change "unsoliticed" into "unsolicited".
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The single iscsit_start_nopin_response_timer() caller does not hold any
locks. Hence remove the comment above this function.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that the next time a response is sent to the initiator that the
credit it had allocated for the aborted request gets freed.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Fixes: 131e6abc67 ("target: Add TFO->abort_task for aborted task resources release") # v3.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of maintaining a list of free I/O contexts, use an sbitmap data
structure to track which I/O contexts are in use and which are free. This
makes the ib_srpt driver more consistent with other LIO drivers.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If submitting a TMF to the target core fails, send the "FUNCTION REJECTED"
response to the initiator.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If submitting an SRP IU to the target core fails, send the SCSI response
"BUSY" to the initiator instead of not sending any response.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The unbalance of master's promiscuity or allmulti will happen after ifdown
and ifup a slave interface which is in a bridge.
When we ifdown a slave interface , both the 'dsa_slave_close' and
'dsa_slave_change_rx_flags' will clear the master's flags. The flags
of master will be decrease twice.
In the other hand, if we ifup the slave interface again, since the
slave's flags were cleared the 'dsa_slave_open' won't set the master's
flag, only 'dsa_slave_change_rx_flags' that triggered by 'br_add_if'
will set the master's flags. The flags of master is increase once.
Only propagating flag changes when a slave interface is up makes
sure this does not happen. The 'vlan_dev_change_rx_flags' had the
same problem and was fixed, and changes here follows that fix.
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Rundong Ge <rdong.ge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a function that sends the SCSI status "BUSY" back to the
initiator. The next patch will add a call to this function in the srpt
target driver.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the code that clears .se_lun from transport_cmd_check_stop_to_fabric()
such that the transport_lun_remove_cmd() call can be moved into
target_release_cmd_kref(). Because this guarantees that
transport_lun_remove_cmd() will be called exactly once, it is safe to change
the cmpxchg() call into a test of se_cmd.lun_ref_active. Inline
transport_lun_remove_cmd() because it is not worth to keep it as a separate
function.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the task management handling rework it is safe to wait for a TMF
that is not in the active state. Hence remove the CMD_T_ACTIVE test from
core_tmr_drain_tmr_list(). Additionally, call __target_check_io_state()
instead of open coding it.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whether or not a session is being torn down does not affect whether or not
SCSI commands are in the task set. Hence remove the "tearing down" checks
from the TMF code. The TRANSPORT_ISTATE_PROCESSING check is left out
because it is now safe to wait for a command that is in that state. The
CMD_T_PRE_EXECUTE is left out because abort processing is postponed until
after commands have left the pre-execute state since the patch that makes
TMF processing synchronous.
See also commit 1c21a48055 ("target: Avoid early CMD_T_PRE_EXECUTE
failures during ABORT_TASK").
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the patch that makes TMF handling synchronous the
write_pending_status() callback function is no longer called. Hence remove
it.
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the tab before '}' and keep the code style consistent.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent print rework we now have the following problem:
pr_{warning,info,debug} expand to __pr which calls libbpf_print.
libbpf_print does va_start and calls __libbpf_pr with va_list argument.
In __base_pr we again do va_start. Because the next argument is a
va_list, we don't get correct pointer to the argument (and print noting
in my case, I don't know why it doesn't crash tbh).
Fix this by changing libbpf_print_fn_t signature to accept va_list and
remove unneeded calls to va_start in the existing users.
Alternatively, this can we solved by exporting __libbpf_pr and
changing __pr macro to (and killing libbpf_print):
{
if (__libbpf_pr)
__libbpf_pr(level, "libbpf: " fmt, ##__VA_ARGS__)
}
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, eeh_pe_reset_full() will only attempt to reset a PE more
than once if activating the reset state and deactivating it both
succeed, but later polling shows that it hasn't become active.
Change this so that it will try up to three times for any reason other
than an unrecoverable slot error and adjust the message generation so
that it's clear weather the reset has ultimately succeeded or failed.
This allows the reset to succeed in some situations where it would
currently fail.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the EEH recovery process considers passed-through devices
as if they were not EEH-aware, which can cause them to be removed as
part of recovery. Because device removal requires cooperation from
the guest, this may lead to the process stalling or deadlocking.
Also, if devices are removed on the host side, they will be removed
from their IOMMU group, making recovery in the guest impossible.
Therefore, alter the recovery process so that passed-through devices
are not removed but are instead left frozen (and marked isolated)
until the guest performs it's own recovery. If firmware thaws a
passed-through PE because it's parent PE has been thawed (because it
was not passed through), re-freeze it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a parameter to eeh_clear_pe_frozen_state() that allows
passed-through PEs to be excluded. Update callers to always pass true
so that there is no change in behaviour.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a parameter to eeh_pe_state_clear() that allows passed-through PEs
to be excluded. Update callers to always pass true so that there is no
change in behaviour.
Also refactor to use direct traversal, to allow the removal of some
boilerplate.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_unfreeze_pe() performs two operations: unfreezing a PE (which may
cause firmware to unfreeze child PEs as well) and de-isolating the PE
and it's children.
To simplify this and support future work, separate out the
de-isolation and perform it at the call sites (when necessary).
There should be no change in behaviour.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 'clear_sw_state' parameter for eeh_pe_clear_frozen_state() is
redundant because it has no effect (except in the rare case of a
hardware error part way through unfreezing a tree of PEs, where it
would dangerously allow partial de-isolation before returning
failure).
It is passed down to __eeh_pe_clear_frozen_state(), and from there to
eeh_unfreeze_pe(), where it causes EEH_PE_ISOLATED to be removed
from the state of each PE during the traversal. However, when the
traversal finishes, EEH_PE_ISOLATED is unconditionally removed by a
call to eeh_pe_state_clear() regardless of the parameter's value.
So remove the flag and pass false to eeh_unfreeze_pe() (to avoid the
rare case described above, as it was before the flag was introduced).
Also, perform the recursion directly in the function and eliminate a
bit of boilerplate.
There should be no change in functionality, except as mentioned above.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since .scsi_done() must only be called after scsi_queue_rq() has
finished, make sure that the SRP initiator driver does not call
.scsi_done() while scsi_queue_rq() is in progress. Although
invoking sg_reset -d while I/O is in progress works fine with kernel
v4.20 and before, that is not the case with kernel v5.0-rc1. This
patch avoids that the following crash is triggered with kernel
v5.0-rc1:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000138
CPU: 0 PID: 360 Comm: kworker/0:1H Tainted: G B 5.0.0-rc1-dbg+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Workqueue: kblockd blk_mq_run_work_fn
RIP: 0010:blk_mq_dispatch_rq_list+0x116/0xb10
Call Trace:
blk_mq_sched_dispatch_requests+0x2f7/0x300
__blk_mq_run_hw_queue+0xd6/0x180
blk_mq_run_work_fn+0x27/0x30
process_one_work+0x4f1/0xa20
worker_thread+0x67/0x5b0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
Cc: <stable@vger.kernel.org>
Fixes: 94a9174c63 ("IB/srp: reduce lock coverage of command completion")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
A soft iwarp driver that uses the host TCP stack via a kernel mode socket
does not need port mapping. In fact, if the port map daemon, iwpmd, is
running, then iwpmd must not try and create/bind a socket to the actual
port for a soft iwarp connection, since the driver already has that socket
bound.
Yet if the soft iwarp driver wants to interoperate with hard iwarp devices
that -are- using port mapping, then the soft iwarp driver's mappings still
need to be maintained and advertised by the iwpm protocol.
This patch enhances the rdma driver<->iwcm interface to allow an iwarp
driver to specify that it does not want port mapping. The iwpm
kernel<->iwpmd interface is also enhanced to pass up this information on
map requests.
Care is taken to interoperate with the current iwpmd version (ABI version
3) and only use the new NL attributes if iwpmd supports ABI version 4.
The ABI version define has also been created in rdma_netlink.h so both
kernel and user code can share it. The iwcm and iwpmd negotiate the ABI
version to use with a new HELLO netlink message.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In order to add new IWPM_NL attributes, the enums for the IWPM commands
attributes are refactored such that a new attribute can be added without
breaking ABI version 3. Instead of sharing nl attribute enums for both
request and response messages, we create separate enums for each IWPM
message request and reply. This allows us to extend any given IWPM
message by adding new attributes for just that message. These new enums
are created, though, in a way to avoid breaking ABI version 3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
So future additions to that struct get initialized by default.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Patch (b6c7a324df "MIPS: Fix get_frame_info() handling of
microMIPS function size.") introduces additional function size
check for microMIPS by only checking insn between ip and ip + func_size.
However, func_size in get_frame_info() is always 0 if KALLSYMS is not
enabled. This causes get_frame_info() to return immediately without
calculating correct frame_size, which in turn causes "Can't analyze
schedule() prologue" warning messages at boot time.
This patch removes func_size check, and let the frame_size check run
up to 128 insns for both MIPS and microMIPS.
Signed-off-by: Jun-Ru Chang <jrjang@realtek.com>
Signed-off-by: Tony Wu <tonywu@realtek.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6c7a324df ("MIPS: Fix get_frame_info() handling of microMIPS function size.")
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <macro@mips.com>
Cc: <yamada.masahiro@socionext.com>
Cc: <peterz@infradead.org>
Cc: <mingo@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
On hi08 chip, There is a possibility of chip hanging when sending doorbell
during reset. We can fix it by prohibiting doorbell during reset.
Fixes: 2d40788825 ("RDMA/hns: Add support for processing send wr and receive wr")
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
On hi08 chip, There is a possibility of chip hanging and some errors when
sending mailbox & doorbell during reset. We can fix it by prohibiting
mailbox and doorbell during reset and reset occurred to ensure that
hardware can work normally.
Fixes: a04ff739f2 ("RDMA/hns: Add command queue support for hip08 RoCE driver")
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In the reset process, the hns3 NIC driver notifies the RoCE driver to
perform reset related processing by calling the .reset_notify() interface
registered by the RoCE driver in hip08 SoC.
In the current version, if a reset occurs simultaneously during the
execution of rmmod or insmod ko, there may be Oops error as below:
Internal error: Oops: 86000007 [#1] PREEMPT SMP
Modules linked in: hns_roce(O) hns3(O) hclge(O) hnae3(O) [last unloaded: hns_roce_hw_v2]
CPU: 0 PID: 14 Comm: kworker/0:1 Tainted: G O 4.19.0-ge00d540 #1
Hardware name: Huawei Technologies Co., Ltd.
Workqueue: events hclge_reset_service_task [hclge]
pstate: 60c00009 (nZCv daif +PAN +UAO)
pc : 0xffff00000100b0b8
lr : 0xffff00000100aea0
sp : ffff000009afbab0
x29: ffff000009afbab0 x28: 0000000000000800
x27: 0000000000007ff0 x26: ffff80002f90c004
x25: 00000000000007ff x24: ffff000008f97000
x23: ffff80003efee0a8 x22: 0000000000001000
x21: ffff80002f917ff0 x20: ffff8000286ea070
x19: 0000000000000800 x18: 0000000000000400
x17: 00000000c4d3225d x16: 00000000000021b8
x15: 0000000000000400 x14: 0000000000000400
x13: 0000000000000000 x12: ffff80003fac6e30
x11: 0000800036303000 x10: 0000000000000001
x9 : 0000000000000000 x8 : ffff80003016d000
x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000040 x4 : 0000000000000000
x3 : 0000000000000004 x2 : 00000000000007ff
x1 : 0000000000000000 x0 : 0000000000000000
Process kworker/0:1 (pid: 14, stack limit = 0x00000000af8f0ad9)
Call trace:
0xffff00000100b0b8
0xffff00000100b3a0
hns_roce_init+0x624/0xc88 [hns_roce]
0xffff000001002df8
0xffff000001006960
hclge_notify_roce_client+0x74/0xe0 [hclge]
hclge_reset_service_task+0xa58/0xbc0 [hclge]
process_one_work+0x1e4/0x458
worker_thread+0x40/0x450
kthread+0x12c/0x130
ret_from_fork+0x10/0x18
Code: bad PC value
In the reset process, we will release the resources firstly, and after the
hardware reset is completed, we will reapply resources and reconfigure the
hardware.
We can solve this problem by modifying both the NIC and the RoCE
driver. We can modify the concurrent processing in the NIC driver to avoid
calling the .reset_notify and .uninit_instance ops at the same time. And
we need to modify the RoCE driver to record the reset stage and the
driver's init/uninit state, and check the state in the .reset_notify,
.init_instance. and uninit_instance functions to avoid NULL pointer
operation.
Fixes: cb7a94c9c8 ("RDMA/hns: Add reset process for RoCE in hip08")
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
For RDMA transports, RDS TOS is an extension of IB QoS(Annex A13)
to provide clients the ability to segregate traffic flows for
different type of data. RDMA CM abstract it for ULPs using
rdma_set_service_type(). Internally, each traffic flow is
represented by a connection with all of its independent resources
like that of a normal connection, and is differentiated by
service type. In other words, there can be multiple qp connections
between an IP pair and each supports a unique service type.
The feature has been added from RDSv4.1 onwards and supports
rolling upgrades. RDMA connection metadata also carries the tos
information to set up SL on end to end context. The original
code was developed by Bang Nguyen in downstream kernel back in
2.6.32 kernel days and it has evolved over period of time.
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
[yanjun.zhu@oracle.com: Adapted original patch with ipv6 changes]
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
RDMA transport maps user tos to underline virtual lanes(VL)
for IB or DSCP values. RDMA CM transport abstract thats for
RDS. TCP transport makes use of default priority 0 and maps
all user tos values to it.
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
[yanjun.zhu@oracle.com: Adapted original patch with ipv6 changes]
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
RDS Service type (TOS) is user-defined and needs to be configured
via RDS IOCTL interface. It must be set before initiating any
traffic and once set the TOS can not be changed. All out-going
traffic from the socket will be associated with its TOS.
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
[yanjun.zhu@oracle.com: Adapted original patch with ipv6 changes]
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
For legacy protocol version incompatibility with non linux RDS,
consumer reject reason being used to convey it to peer. But the
choice of reject reason value as '1' was really poor.
Anyway for interoperability reasons with shipping products,
it needs to be supported. For any future versions, properly
encoded reject reason should to be used.
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
[yanjun.zhu@oracle.com: Adapted original patch with ipv6 changes]
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Mark RDSv3.1 as compat version and add v4.1 version macro's.
Subsequent patches enable TOS(Type of Service) feature which is
tied with v4.1 for RDMA transport.
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
[yanjun.zhu@oracle.com: Adapted original patch with ipv6 changes]
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Currently a packet is marked for loopback only if the source and
destination addresses equals. This is not enough when multiple gids are
present in rxe device's gid table and the traffic is from one gid to
another. Fix it by marking the packet for loopback if the destination MAC
address is equal to the source MAC address.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Tested-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Move the function rxe_init_av() to rxe_av.c file and use it instead of
calling rxe_av_from_attr() and rxe_av_fill_ip_info(), also remove the
unused rxe_dev parameter from rxe_init_av().
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Commit 7b3415f581 ("MIPS: Loongson32: Remove unused platform devices")
removed the definitions of platform devices which have no in tree
drivers from common Loongson32 code, but missed their removal from
Loongson 1B board code in arch/mips/loongson32/ls1b/board.c. This causes
build failures due to the missing declarations of ls1x_dma_pdev,
ls1x_nand_pdev & their associated *_set_platdata functions.
Remove the dead code from arch/mips/loongson32/ls1b/board.c to fix the
build.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 7b3415f581 ("MIPS: Loongson32: Remove unused platform devices")
Commit a96d68ba3b ("MIPS: Loongson32: clarify we don't support MIPS16
and merge configs") attempted to reduce duplication in Kconfig by
consolidating some selects common to Loongson 1B & 1C CPUs under
CPU_LOONGSON1. Unfortunately it clearly wasn't tested because by
removing SYS_SUPPORTS_32BIT_KERNEL it prevented 32BIT from being enabled
leading to all sorts of strange build errors from a kernel configured to
build as neither 32 nor 64 bit.
Both loongson1b_defconfig & loongson1c_defconfig failed to build due to
this problem.
Revert the cleanup portions of commit a96d68ba3b ("MIPS: Loongson32:
clarify we don't support MIPS16 and merge configs"), keeping only its
removal of the selection of SYS_SUPPORTS_MIPS16.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a96d68ba3b ("MIPS: Loongson32: clarify we don't support MIPS16 and merge configs")
Instead of sizeof use pre-defined constant for UUID representation.
While here, drop the implementation details of uuid_t type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
If tmpfiles can be made persistent, then newly created tmpfiles need to
be treated like any other new files in policy.
This patch indicates which newly created tmpfiles are in policy, causing
the file hash to be calculated on __fput().
Reported-by: Ignaz Forster <ignaz.forster@gmx.de>
[rgoldwyn@suse.com: Call ima_post_create_tmpfile() in vfs_tmpfile() as
opposed to do_tmpfile(). This will help the case for overlayfs where
copy_up is denied while overwriting a file.]
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Fixes gcc '-Wunused-but-set-variable' warning:
security/integrity/evm/evm_main.c: In function 'init_evm':
security/integrity/evm/evm_main.c:566:21: warning:
variable 'xattr' set but not used [-Wunused-but-set-variable]
Commit 21af766314 ("EVM: turn evm_config_xattrnames into a list")
defined and set "xattr", but never used it.
[zohar@linux.ibm.com: tweaked the patch description explanation]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Properly start the enumeration associated with match_table_t at zero,
making Opt_err/Opt_error the last enumeration value.
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
This patch allows the kexec_file_load syscall to verify the PE signed
kernel image signature based on the preboot keys stored in the .platform
keyring, as fall back, if the signature verification failed due to not
finding the public key in the secondary or builtin keyrings.
This commit adds a VERIFY_USE_PLATFORM_KEYRING similar to previous
VERIFY_USE_SECONDARY_KEYRING indicating that verify_pkcs7_signature
should verify the signature using platform keyring. Also, decrease
the error message log level when verification failed with -ENOKEY,
so that if called tried multiple time with different keyring it
won't generate extra noises.
Signed-off-by: Kairui Song <kasong@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Dave Young <dyoung@redhat.com> (for kexec_file_load part)
[zohar@linux.ibm.com: tweaked the first paragraph of the patch description,
and fixed checkpatch warning.]
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Fixes the following sparse warnings:
drivers/infiniband/hw/hns/hns_roce_hw_v2.c:5822:5: warning:
symbol 'hns_roce_v2_query_srq' was not declared. Should it be static?
drivers/infiniband/hw/hns/hns_roce_srq.c:158:6: warning:
symbol 'hns_roce_srq_free' was not declared. Should it be static?
drivers/infiniband/hw/hns/hns_roce_srq.c:81:5: warning:
symbol 'hns_roce_srq_alloc' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
commit 9dc92c4517 ("integrity: Define a trusted platform keyring")
introduced a .platform keyring for storing preboot keys, used for
verifying kernel image signatures. Currently only IMA-appraisal is able
to use the keyring to verify kernel images that have their signature
stored in xattr.
This patch exposes the .platform keyring, making it accessible for
verifying PE signed kernel images as well.
Suggested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Kairui Song <kasong@redhat.com>
Cc: David Howells <dhowells@redhat.com>
[zohar@linux.ibm.com: fixed checkpatch errors, squashed with patch fix]
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Commit f263f2a2c6 ("MIPS: Compile post DMA flush only when needed")
pushed the selection of ARCH_HAS_SYNC_DMA_FOR_CPU down to various
SYS_HAS_CPU_* Kconfig entries corresponding to CPUs for which
cpu_needs_post_dma_flush() might return true, but unfortunately missed
the fact that some of these CPUs can be used in configurations with
DMA_NONCOHERENT=n. When this is the case the kernel build does not
include our definition of arch_sync_dma_for_cpu() from
arch/mips/mm/dma-noncoherent.c and the build fails with a link error.
One example of this problem is ip27_defconfig:
kernel/dma/direct.o: In function `dma_direct_sync_single_for_cpu':
direct.c:(.text+0x6c): undefined reference to `arch_sync_dma_for_cpu'
kernel/dma/direct.o: In function `dma_direct_sync_sg_for_cpu':
direct.c:(.text+0x1f0): undefined reference to `arch_sync_dma_for_cpu'
kernel/dma/direct.o: In function `dma_direct_alloc':
direct.c:(.text+0xc20): undefined reference to `arch_dma_alloc'
kernel/dma/direct.o: In function `dma_direct_free':
direct.c:(.text+0xc3c): undefined reference to `arch_dma_free'
make[1]: *** [Makefile:1021: vmlinux] Error 1
make: *** [Makefile:152: sub-make] Error 2
Fix this by selecting ARCH_HAS_SYNC_DMA_FOR_CPU only when
DMA_NONCOHERENT is also selected. The SYS_HAS_CPU_BMIPS5000 case is left
as-is because systems with that CPU always select DMA_NONCOHERENT
anyway.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f263f2a2c6 ("MIPS: Compile post DMA flush only when needed")
Limit the NEWCLIENT boost to only give its small priority boost to fresh
clients only that have no dependencies.
The idea for using NEWCLIENT boosting, commit b16c765122 ("drm/i915:
Priority boost for new clients"), is that short-lived streams are often
interactive and require lower latency -- and that by executing those
ahead of the long running hogs, the short-lived clients do little to
interfere with the system throughput by virtue of their short-lived
nature. However, we were only considering the client's own timeline for
determining whether or not it was a fresh stream. This allowed for
compositors to wake up before their vblank and bump all of its client
streams. However, in testing with media-bench this results in chaining
all cooperating contexts together preventing us from being able to
reorder contexts to reduce bubbles (pipeline stalls), overall increasing
latency, and reducing system throughput. The exact opposite of our
intent. The compromise of applying the NEWCLIENT boost to strictly fresh
clients (that do not wait upon anything else) should maintain the
"real-time response under load" characteristics of FQ_CODEL, without
locking together the long chains of dependencies across the system.
References: b16c765122 ("drm/i915: Priority boost for new clients")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190204150101.30759-1-chris@chris-wilson.co.uk
