This binding supersedes the bcm2835-pm-wdt binding which only covered
enough to provide a watchdog, but the HW block is actually mostly
about power domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Rob Herring <robh@kernel.org> (v3)
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Currently rdev is dereferenced when assigning desc before rdev is null
checked, hence there is a potential null pointer dereference on rdev.
Fix this by null checking rdev first.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165 ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware-owned GPIO expander on RPi 3 B+ must be in same state
after a reboot as initial power on. Otherwise this would cause a
network boot failure of the BOOTROM. So inform the VC4 firmware to restore
the expander before doing a reboot.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Add latest firmware property tags from the latest Raspberry Pi downstream
kernel. This is needed to use the reboot notify in the following
commit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, the board's
fixed 3.3V power regulator provides overall power via VBAT and I/O power
via VDDIO. The RTC clock output from the SoC provides the LPO low power
clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART3 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO1 and
DLDO2 regulator outputs from the PMIC provide overall power via VBAT and
I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides
the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin
PI12. This can be represented in multiple ways. This patch puts the
pinctrl property in the pin controller node. This is due to limitations
in Linux, where pinmux settings, even the same one, can not be shared
by multiple devices. Thus we cannot put it in both the WiFi and
Bluetooth device nodes. Putting it the CCU node is another option, but
Linux's CCU driver does not handle pinctrl. Also the pin controller is
guaranteed to be initialized after the CCU, when clocks are available.
And any other devices that use muxed pins are guaranteed to be
initialized after the pin controller. Thus having the CLK_OUT_A pinmux
reference be in the pin controller node is a good choice without having
to deal with implementation issues.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The design of the Bananapi M2 Ultra has both DLDO1 and DLDO2 regulators
provide power to the WiFi+BT module, which is based on the Broadcom
BCM43438 or BCM43430 chip. Each regulator output from the PMIC can supply
up to 200 mA. The datasheet of the chip suggests a maximum power draw of
up to 360 mA when transmitting, thus requiring two outputs from the PMIC
to handle the load. However the device tree only references one of them,
leaving the other unused and possibly turned off.
This patch marks both as always-on, since we don't have a proper binding
to specify two regulators as "bound together". The name and constraints
of DLDO2 are also added.
Fixes: da7ac948fa ("ARM: dts: sun8i: Add board dts file for Banana Pi M2
Ultra")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
CLK_OUT_A, an external clock output function driven from the clock
control unit, on the R40 is sometimes used to provide a low rate low
power clock to a WiFi or Bluetooth controller.
This patch adds a pinmux setting for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
UART3 on the PG pingroup on the R40 SoC is commonly used to connect the
bluetooth controller in a WiFi+Bluetooth combo chip, with the WiFi bits
also on the PG pingroup.
This patch adds two device nodes for UART3 on PG pingroup, one for the
RX/TX pins, and one for the RTS/CTS pins. Consumers can reference either
just the RX/TX pinmux setting or both, depending on the application.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
By making MCLK parent of DAI clocks, when querying the rate of the
clock the rate returned is now given from the parent clock so
gives the MCLK rate rather than 0 as previously returned. This is
a bit misleading, and actually there's no major reason why we can't
at least return the DAI WCLK rate, as set in HW, so that's what we
now do.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Of the tunables available for the bfq I/O scheduler, the only one
missing from the documentation in 'Documentation/block/bfq-iosched.txt'
is slice_idle_us. Add this tunable to the documentation and a short
explanation of its purpose.
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For platforms using the Common Clock Framework to control the
codec's DAI clocks, MCLK should be enabled prior to DAI clocks
being turned on. For some platforms the codec is already
provided with an MCLK reference and can therefore control MCLK
itself as it needs to.
To improve functionality MCLK is now added as a parent to the
DAI clocks, if MCLK was provided, so that if they are enabled MCLK
will automatically be enabled as a prerequisite by the CCF.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rumble support on SHANWAN PS3 gamepad is not working when a user
program has asked it to. If a HID Output Reports is sent via Control
Channel then it will be discard by gamepad, thus rumble motor and led
settings in Output Report are ignored.
This patch therefore sends HID Output Report via Interrupt Channel to
SHANWAN gamepad instead of Control Channel, fixing rumble motor and
led settings.
Signed-off-by: Hongye Yuan <outmatch@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Transform the one-time check for a SHANWAN PS3 clone gamepad into a
quirk, to avoid doing the same string comparison in multiple places.
Signed-off-by: Hongye Yuan <outmatch@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
When modifying the free space tree we can end up COWing one of its extent
buffers which in turn might result in allocating a new chunk, which in
turn can result in flushing (finish creation) of pending block groups. If
that happens we can deadlock because creating a pending block group needs
to update the free space tree, and if any of the updates tries to modify
the same extent buffer that we are COWing, we end up in a deadlock since
we try to write lock twice the same extent buffer.
So fix this by skipping pending block group creation if we are COWing an
extent buffer from the free space tree. This is a case missed by commit
5ce555578e ("Btrfs: fix deadlock when writing out free space caches").
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202173
Fixes: 5ce555578e ("Btrfs: fix deadlock when writing out free space caches")
CC: stable@vger.kernel.org # 4.18+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The recent rework that makes btrfs' remap_file_range operation use the
generic helper generic_remap_file_range_prep() introduced a race between
relocation and reflinking (for both cloning and deduplication) the file
extents between the source and destination inodes.
This happens because we no longer lock the source range anymore, and we do
not lock it anymore because we wait for direct IO writes and writeback to
complete early on the code path right after locking the inodes, which
guarantees no other file operations interfere with the reflinking. However
there is one exception which is relocation, since it replaces the byte
number of file extents items in the fs tree after locking the range the
file extent items represent. This is a problem because after finding each
file extent to clone in the fs tree, the reflink process copies the file
extent item into a local buffer, releases the search path, inserts new
file extent items in the destination range and then increments the
reference count for the extent mentioned in the file extent item that it
previously copied to the buffer. If right after copying the file extent
item into the buffer and releasing the path the relocation process
updates the file extent item to point to the new extent, the reflink
process ends up creating a delayed reference to increment the reference
count of the old extent, for which the relocation process already created
a delayed reference to drop it. This results in failure to run delayed
references because we will attempt to increment the count of a reference
that was already dropped. This is illustrated by the following diagram:
CPU 1 CPU 2
relocation is running
btrfs_clone_files()
btrfs_clone()
--> finds extent item
in source range
point to extent
at bytenr X
--> copies it into a
local buffer
--> releases path
replace_file_extents()
--> successfully locks the
range represented by
the file extent item
--> replaces disk_bytenr
field in the file
extent item with some
other value Y
--> creates delayed reference
to increment reference
count for extent at
bytenr Y
--> creates delayed reference
to drop the extent at
bytenr X
--> starts transaction
--> creates delayed
reference to
increment extent
at bytenr X
<delayed references are run, due to a transaction
commit for example, and the transaction is aborted
with -EIO because we attempt to increment reference
count for the extent at bytenr X after we freed it>
When this race is hit the running transaction ends up getting aborted with
an -EIO error and a trace like the following is produced:
[ 4382.553858] WARNING: CPU: 2 PID: 3648 at fs/btrfs/extent-tree.c:1552 lookup_inline_extent_backref+0x4f4/0x650 [btrfs]
(...)
[ 4382.556293] CPU: 2 PID: 3648 Comm: btrfs Tainted: G W 4.20.0-rc6-btrfs-next-41 #1
[ 4382.556294] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014
[ 4382.556308] RIP: 0010:lookup_inline_extent_backref+0x4f4/0x650 [btrfs]
(...)
[ 4382.556310] RSP: 0018:ffffac784408f738 EFLAGS: 00010202
[ 4382.556311] RAX: 0000000000000001 RBX: ffff8980673c3a48 RCX: 0000000000000001
[ 4382.556312] RDX: 0000000000000008 RSI: 0000000000000000 RDI: 0000000000000000
[ 4382.556312] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001
[ 4382.556313] R10: 0000000000000001 R11: ffff897f40000000 R12: 0000000000001000
[ 4382.556313] R13: 00000000c224f000 R14: ffff89805de9bd40 R15: ffff8980453f4548
[ 4382.556315] FS: 00007f5e759178c0(0000) GS:ffff89807b300000(0000) knlGS:0000000000000000
[ 4382.563130] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 4382.563562] CR2: 00007f2e9789fcbc CR3: 0000000120512001 CR4: 00000000003606e0
[ 4382.564005] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 4382.564451] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 4382.564887] Call Trace:
[ 4382.565343] insert_inline_extent_backref+0x55/0xe0 [btrfs]
[ 4382.565796] __btrfs_inc_extent_ref.isra.60+0x88/0x260 [btrfs]
[ 4382.566249] ? __btrfs_run_delayed_refs+0x93/0x1650 [btrfs]
[ 4382.566702] __btrfs_run_delayed_refs+0xa22/0x1650 [btrfs]
[ 4382.567162] btrfs_run_delayed_refs+0x7e/0x1d0 [btrfs]
[ 4382.567623] btrfs_commit_transaction+0x50/0x9c0 [btrfs]
[ 4382.568112] ? _raw_spin_unlock+0x24/0x30
[ 4382.568557] ? block_rsv_release_bytes+0x14e/0x410 [btrfs]
[ 4382.569006] create_subvol+0x3c8/0x830 [btrfs]
[ 4382.569461] ? btrfs_mksubvol+0x317/0x600 [btrfs]
[ 4382.569906] btrfs_mksubvol+0x317/0x600 [btrfs]
[ 4382.570383] ? rcu_sync_lockdep_assert+0xe/0x60
[ 4382.570822] ? __sb_start_write+0xd4/0x1c0
[ 4382.571262] ? mnt_want_write_file+0x24/0x50
[ 4382.571712] btrfs_ioctl_snap_create_transid+0x117/0x1a0 [btrfs]
[ 4382.572155] ? _copy_from_user+0x66/0x90
[ 4382.572602] btrfs_ioctl_snap_create+0x66/0x80 [btrfs]
[ 4382.573052] btrfs_ioctl+0x7c1/0x30e0 [btrfs]
[ 4382.573502] ? mem_cgroup_commit_charge+0x8b/0x570
[ 4382.573946] ? do_raw_spin_unlock+0x49/0xc0
[ 4382.574379] ? _raw_spin_unlock+0x24/0x30
[ 4382.574803] ? __handle_mm_fault+0xf29/0x12d0
[ 4382.575215] ? do_vfs_ioctl+0xa2/0x6f0
[ 4382.575622] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[ 4382.576020] do_vfs_ioctl+0xa2/0x6f0
[ 4382.576405] ksys_ioctl+0x70/0x80
[ 4382.576776] __x64_sys_ioctl+0x16/0x20
[ 4382.577137] do_syscall_64+0x60/0x1b0
[ 4382.577488] entry_SYSCALL_64_after_hwframe+0x49/0xbe
(...)
[ 4382.578837] RSP: 002b:00007ffe04bf64c8 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
[ 4382.579174] RAX: ffffffffffffffda RBX: 00005564136f3050 RCX: 00007f5e74724dd7
[ 4382.579505] RDX: 00007ffe04bf64d0 RSI: 000000005000940e RDI: 0000000000000003
[ 4382.579848] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000044
[ 4382.580164] R10: 0000000000000541 R11: 0000000000000202 R12: 00005564136f3010
[ 4382.580477] R13: 0000000000000003 R14: 00005564136f3035 R15: 00005564136f3050
[ 4382.580792] irq event stamp: 0
[ 4382.581106] hardirqs last enabled at (0): [<0000000000000000>] (null)
[ 4382.581441] hardirqs last disabled at (0): [<ffffffff8d085842>] copy_process.part.32+0x6e2/0x2320
[ 4382.581772] softirqs last enabled at (0): [<ffffffff8d085842>] copy_process.part.32+0x6e2/0x2320
[ 4382.582095] softirqs last disabled at (0): [<0000000000000000>] (null)
[ 4382.582413] ---[ end trace d3c188e3e9367382 ]---
[ 4382.623855] BTRFS: error (device sdc) in btrfs_run_delayed_refs:2981: errno=-5 IO failure
[ 4382.624295] BTRFS info (device sdc): forced readonly
Fix this by locking the source range before searching for the file extent
items in the fs tree, since the relocation process will try to lock the
range a file extent item represents before updating it with the new extent
location.
Fixes: 34a28e3d77 ("Btrfs: use generic_remap_file_range_prep() for cloning and deduplication")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The recent rework that makes btrfs' remap_file_range operation use the
generic helper generic_remap_file_range_prep() introduced a race between
writeback and cloning a range that covers the eof extent of the source
file into a destination offset that is greater then the same file's size.
This happens because we now wait for writeback to complete before doing
the truncation of the eof block, while previously we did the truncation
and then waited for writeback to complete. This leads to a race between
writeback of the truncated block and cloning the file extents in the
source range, because we copy each file extent item we find in the fs
root into a buffer, then release the path and then increment the reference
count for the extent referred in that file extent item we copied, which
can no longer exist if writeback of the truncated eof block completes
after we copied the file extent item into the buffer and before we
incremented the reference count. This is illustrated by the following
diagram:
CPU 1 CPU 2
btrfs_clone_files()
btrfs_cont_expand()
btrfs_truncate_block()
--> zeroes part of the
page containg eof,
marking it for
delalloc
btrfs_clone()
--> finds extent item
covering eof,
points to extent
at bytenr X
--> copies it into a
local buffer
--> releases path
writeback starts
btrfs_finish_ordered_io()
insert_reserved_file_extent()
__btrfs_drop_extents()
--> creates delayed
reference to drop
the extent at
bytenr X
--> starts transaction
--> creates delayed
reference to
increment extent
at bytenr X
<delayed references are run, due to a transaction
commit for example, and the transaction is aborted
with -EIO because we attempt to increment reference
count for the extent at bytenr X after we freed it>
When this race is hit the running transaction ends up getting aborted with
an -EIO error and a trace like the following is produced:
[ 4382.553858] WARNING: CPU: 2 PID: 3648 at fs/btrfs/extent-tree.c:1552 lookup_inline_extent_backref+0x4f4/0x650 [btrfs]
(...)
[ 4382.556293] CPU: 2 PID: 3648 Comm: btrfs Tainted: G W 4.20.0-rc6-btrfs-next-41 #1
[ 4382.556294] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014
[ 4382.556308] RIP: 0010:lookup_inline_extent_backref+0x4f4/0x650 [btrfs]
(...)
[ 4382.556310] RSP: 0018:ffffac784408f738 EFLAGS: 00010202
[ 4382.556311] RAX: 0000000000000001 RBX: ffff8980673c3a48 RCX: 0000000000000001
[ 4382.556312] RDX: 0000000000000008 RSI: 0000000000000000 RDI: 0000000000000000
[ 4382.556312] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001
[ 4382.556313] R10: 0000000000000001 R11: ffff897f40000000 R12: 0000000000001000
[ 4382.556313] R13: 00000000c224f000 R14: ffff89805de9bd40 R15: ffff8980453f4548
[ 4382.556315] FS: 00007f5e759178c0(0000) GS:ffff89807b300000(0000) knlGS:0000000000000000
[ 4382.563130] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 4382.563562] CR2: 00007f2e9789fcbc CR3: 0000000120512001 CR4: 00000000003606e0
[ 4382.564005] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 4382.564451] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 4382.564887] Call Trace:
[ 4382.565343] insert_inline_extent_backref+0x55/0xe0 [btrfs]
[ 4382.565796] __btrfs_inc_extent_ref.isra.60+0x88/0x260 [btrfs]
[ 4382.566249] ? __btrfs_run_delayed_refs+0x93/0x1650 [btrfs]
[ 4382.566702] __btrfs_run_delayed_refs+0xa22/0x1650 [btrfs]
[ 4382.567162] btrfs_run_delayed_refs+0x7e/0x1d0 [btrfs]
[ 4382.567623] btrfs_commit_transaction+0x50/0x9c0 [btrfs]
[ 4382.568112] ? _raw_spin_unlock+0x24/0x30
[ 4382.568557] ? block_rsv_release_bytes+0x14e/0x410 [btrfs]
[ 4382.569006] create_subvol+0x3c8/0x830 [btrfs]
[ 4382.569461] ? btrfs_mksubvol+0x317/0x600 [btrfs]
[ 4382.569906] btrfs_mksubvol+0x317/0x600 [btrfs]
[ 4382.570383] ? rcu_sync_lockdep_assert+0xe/0x60
[ 4382.570822] ? __sb_start_write+0xd4/0x1c0
[ 4382.571262] ? mnt_want_write_file+0x24/0x50
[ 4382.571712] btrfs_ioctl_snap_create_transid+0x117/0x1a0 [btrfs]
[ 4382.572155] ? _copy_from_user+0x66/0x90
[ 4382.572602] btrfs_ioctl_snap_create+0x66/0x80 [btrfs]
[ 4382.573052] btrfs_ioctl+0x7c1/0x30e0 [btrfs]
[ 4382.573502] ? mem_cgroup_commit_charge+0x8b/0x570
[ 4382.573946] ? do_raw_spin_unlock+0x49/0xc0
[ 4382.574379] ? _raw_spin_unlock+0x24/0x30
[ 4382.574803] ? __handle_mm_fault+0xf29/0x12d0
[ 4382.575215] ? do_vfs_ioctl+0xa2/0x6f0
[ 4382.575622] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[ 4382.576020] do_vfs_ioctl+0xa2/0x6f0
[ 4382.576405] ksys_ioctl+0x70/0x80
[ 4382.576776] __x64_sys_ioctl+0x16/0x20
[ 4382.577137] do_syscall_64+0x60/0x1b0
[ 4382.577488] entry_SYSCALL_64_after_hwframe+0x49/0xbe
(...)
[ 4382.578837] RSP: 002b:00007ffe04bf64c8 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
[ 4382.579174] RAX: ffffffffffffffda RBX: 00005564136f3050 RCX: 00007f5e74724dd7
[ 4382.579505] RDX: 00007ffe04bf64d0 RSI: 000000005000940e RDI: 0000000000000003
[ 4382.579848] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000044
[ 4382.580164] R10: 0000000000000541 R11: 0000000000000202 R12: 00005564136f3010
[ 4382.580477] R13: 0000000000000003 R14: 00005564136f3035 R15: 00005564136f3050
[ 4382.580792] irq event stamp: 0
[ 4382.581106] hardirqs last enabled at (0): [<0000000000000000>] (null)
[ 4382.581441] hardirqs last disabled at (0): [<ffffffff8d085842>] copy_process.part.32+0x6e2/0x2320
[ 4382.581772] softirqs last enabled at (0): [<ffffffff8d085842>] copy_process.part.32+0x6e2/0x2320
[ 4382.582095] softirqs last disabled at (0): [<0000000000000000>] (null)
[ 4382.582413] ---[ end trace d3c188e3e9367382 ]---
[ 4382.623855] BTRFS: error (device sdc) in btrfs_run_delayed_refs:2981: errno=-5 IO failure
[ 4382.624295] BTRFS info (device sdc): forced readonly
Fix this by waiting for writeback to complete after truncating the eof
block.
Fixes: 34a28e3d77 ("Btrfs: use generic_remap_file_range_prep() for cloning and deduplication")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
To pick the changes from:
a428afe82f ("net: bridge: add support for user-controlled bool options")
a025fb5f49 ("geneve: Allow configuration of DF behaviour")
b4d3069783 ("vxlan: Allow configuration of DF behaviour")
Silencing this tools/ build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/if_link.h' differs from latest version at 'include/uapi/linux/if_link.h'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Link: https://lkml.kernel.org/n/tip-wq410s2wuqv5k980bidw0ju8@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Recently we run a network test over ipcomp virtual tunnel.We find that
if a ipv4 packet needs fragment, then the peer can't receive
it.
We deep into the code and find that when packet need fragment the smaller
fragment will be encapsulated by ipip not ipcomp. So when the ipip packet
goes into xfrm, it's skb->dev is not properly set. The ipv4 reassembly code
always set skb'dev to the last fragment's dev. After ipv4 defrag processing,
when the kernel rp_filter parameter is set, the skb will be drop by -EXDEV
error.
This patch adds compatible support for the ipip process in ipcomp virtual tunnel.
Signed-off-by: Su Yanjun <suyj.fnst@cn.fujitsu.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With very small change to test script we can trigger softlockup due to
bogus assignment of 'p' (policy to be examined) on restart.
Previously the two to-be-merged nodes had same address/prefixlength pair,
so no erase/reinsert was necessary, we only had to append the list from
node a to b.
If prefix lengths are different, the node has to be deleted and re-inserted
into the tree, with the updated prefix length. This was broken; due to
bogus update to 'p' this loops forever.
Add a 'restart' label and use that instead.
While at it, don't perform the unneeded reinserts of the policies that
are already sorted into the 'new' node.
A previous patch in this series made xfrm_policy_inexact_list_reinsert()
use the relative position indicator to sort policies according to age in
case priorities are identical.
Fixes: 6ac098b2a9 ("xfrm: policy: add 2nd-level saddr trees for inexact policies")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
... and back to inexact tree.
Repeat ping test after each htresh change: lookup results must not change.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
"newpos" has wrong scope. It must be NULL on each iteration of the loop.
Otherwise, when policy is to be inserted at the start, we would instead
insert at point found by the previous loop-iteration instead.
Also, we need to unlink the policy before we reinsert it to the new node,
else we can get next-points-to-self loops.
Because policies are only ordered by priority it is irrelevant which policy
is "more recent" except when two policies have same priority.
(the more recent one is placed after the older one).
In these cases, we can use the ->pos id number to know which one is the
'older': the higher the id, the more recent the policy.
So we only need to unlink all policies from the node that is about to be
removed, and insert them to the replacement node.
Fixes: 9cf545ebd5 ("xfrm: policy: store inexact policies in a tree ordered by destination address")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
An xfrm hash rebuild has to reset the inexact policy list before the
policies get re-inserted: A change of hash thresholds will result in
policies to get moved from inexact tree to the policy hash table.
If the thresholds are increased again later, they get moved from hash
table to inexact tree.
We must unlink all policies from the inexact tree before re-insertion.
Otherwise 'migrate' may find policies that are in main hash table a
second time, when it searches the inexact lists.
Furthermore, re-insertion without deletion can cause elements ->next to
point back to itself, causing soft lockups or double-frees.
Reported-by: syzbot+9d971dd21eb26567036b@syzkaller.appspotmail.com
Fixes: 9cf545ebd5 ("xfrm: policy: store inexact policies in a tree ordered by destination address")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Hash rebuild will re-set all the inexact entries, then re-insert them.
Lookups that can occur in parallel will therefore not find any policies.
This was safe when lookups were still guarded by rwlock.
After rcu-ification, lookups check the hash_generation seqcount to detect
when a hash resize takes place. Hash rebuild missed the needed increment.
Hash resizes and hash rebuilds cannot occur in parallel (both acquire
hash_resize_mutex), so just increment xfrm_hash_generation, like resize.
Fixes: a7c44247f7 ("xfrm: policy: make xfrm_policy_lookup_bytype lockless")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This function was modeled on the 'exact' insert one, which did not use
the rcu variant either.
When I fixed the 'exact' insert I forgot to propagate this to my
development tree, so the inexact variant retained the bug.
Fixes: 9cf545ebd5 ("xfrm: policy: store inexact policies in a tree ordered by destination address")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The existing script lacks a policy pattern that triggers 'tree node
merges' in the kernel.
Consider adding policy affecting following subnet:
pol1: dst 10.0.0.0/22
pol2: dst 10.0.0.0/23 # adds to existing 10.0.0.0/22 node
-> no problems here. But now, lets consider reverse order:
pol1: dst 10.0.0.0/24
pol2: dst 10.0.0.0/23 # CANNOT add to existing node
When second policy gets added, the kernel must check that the new node
("10.0.0.0/23") doesn't overlap with any existing subnet.
Example:
dst 10.0.0.0/24
dst 10.0.0.1/24
dst 10.0.0.0/23
When the third policy gets added, the kernel must replace the nodes for
the 10.0.0.0/24 and 10.0.0.1/24 policies with a single one and must merge
all the subtrees/lists stored in those nodes into the new node.
The existing test cases only have overlaps with a single node, so no
merging takes place (we can always remove the 'old' node and replace
it with the new subnet prefix).
Add a few 'block policies' in a pattern that triggers this, with a priority
that will make kernel prefer the 'esp' rules.
Make sure the 'tunnel ping' tests still pass after they have been added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This converts the DesignWare (dw) SPI master driver to
use GPIO descriptors for chip select handling.
This driver has a duplicate DT parser in addition to the
one in the core, sets up the line as non-asserted and
relies on the core to drive the GPIOs.
It is a pretty straight-forward conversion.
Cc: Talel Shenhar <talel@amazon.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Linuxarm <linuxarm@huawei.com>
Tested-by: Jay Fang <f.fangjian@huawei.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the DaVinci SPI master driver to use GPIO
descriptors for chip select handling.
DaVinci parses the device tree a second time for the chip
select GPIOs (no relying on the parsing already happening
in the SPI core) and handles inversion semantics locally.
We simply drop the extra parsing and set up and move the
CS handling to the core and gpiolib. The fact that the
driver is actively driving the GPIO in the
davinci_spi_chipselect() callback is confusing since the
host does not set SPI_MASTER_GPIO_SS so this should not
ever get called when using GPIO CS. I put in a comment
about this.
This driver also supports instantiation from board files,
but these are all using native chip selects so no problem
with GPIO lines here.
Cc: David Lechner <david@lechnology.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the CLPS711x SPI master driver to use GPIO
descriptors for chip select handling.
The CLPS711x driver was merely requesting the GPIO and
setting the CS line non-asserted so this was a pretty
straight-forward conversion. The setup callback goes away.
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the Cadence SPI master driver to use GPIO
descriptors for chip select handling.
The Cadence driver was allocating a state container just
to hold the requested GPIO line and contained lots of
polarity inversion code. As this is all handled by gpiolib
and a simple devm_* request in the core, and as the driver
is fully device tree only, most of this code chunk goes
away in favour of central handling. The setup/cleanup
callbacks goes away.
This driver does NOT drive the CS line by setting the
value of the GPIO so it relies on the SPI core to do
this, which should work just fine with the descriptors.
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Janek Kotas <jank@cadence.com>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the Atmel SPI master driver to use GPIO descriptors
for chip select handling.
The Atmel driver has duplicate code to look up and initialize CS
GPIOs from the device tree, so this is removed. It further has code
to retrieve a CS GPIO from .controller_data but this seems to be
completely unused in the kernel (legacy codepath?) so I deleted
this support. It keeps track of polarity when switching the CS, but
this is not needed anymore since we moved this over to the gpiolib.
The local handling of the "npcs_pin" (I guess this might mean
"negative polarity chip select pin") is preserved, but I strongly
suspect this can be switched over to handling by the core and
using the SPI_MASTER_GPIO_SS flag on the master to assure that
the additional CS handling in the driver is also done.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Radu Pirea <radu.pirea@microchip.com>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the ATH79 SPI master driver to use GPIO descriptors
for chip select handling.
The ATH79 driver was requesting the GPIO and driving it from the
bitbang .chipselect callback. Do not request it anymore as the SPI
core will request it, remove the line inversion semantics for the
GPIO case (handled by gpiolib) and let the SPI core deal with
requesting the GPIO line from the device tree node of the controller.
This driver can be instantiated from a board file (no device tree)
but the board files only use native CS (no GPIO lines) so we should
be fine just letting the SPI core grab the GPIO from the device.
The fact that the driver is actively driving the GPIO in the
ath79_spi_chipselect() callback is confusing since the host does
not set SPI_MASTER_GPIO_SS so this should not ever get called when
using GPIO CS. I put in a comment about this.
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Alban Bedel <albeu@free.fr>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This augments the SPI core to optionally use GPIO descriptors
for chip select on a per-master-driver opt-in basis.
Drivers using this will rely on the SPI core to look up
GPIO descriptors associated with the device, such as
when using device tree or board files with GPIO descriptor
tables.
When getting descriptors from the device tree, this will in
turn activate the code in gpiolib that was
added in commit 6953c57ab1
("gpio: of: Handle SPI chipselect legacy bindings")
which means that these descriptors are aware of the active
low semantics that is the default for SPI CS GPIO lines
and we can assume that all of these are "active high" and
thus assign SPI_CS_HIGH to all CS lines on the DT path.
The previously used gpio_set_value() would call down into
gpiod_set_raw_value() and ignore the polarity inversion
semantics.
It seems like many drivers go to great lengths to set up the
CS GPIO line as non-asserted, respecting SPI_CS_HIGH. We pull
this out of the SPI drivers and into the core, and by simply
requesting the line as GPIOD_OUT_LOW when retrieveing it from
the device and relying on the gpiolib to handle any inversion
semantics. This way a lot of code can be simplified and
removed in each converted driver.
The end goal after dealing with each driver in turn, is to
delete the non-descriptor path (of_spi_register_master() for
example) and let the core deal with only descriptors.
The different SPI drivers have complex interactions with the
core so we cannot simply change them all over, we need to use
a stepwise, bisectable approach so that each driver can be
converted and fixed in isolation.
This patch has the intended side effect of adding support for
ACPI GPIOs as it starts relying on gpiod_get_*() to get
the GPIO handle associated with the device.
Cc: Linuxarm <linuxarm@huawei.com>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Fangjian (Turing) <f.fangjian@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAI component probe is not called if it is not present
in component list during sound card registration.
Check if component is available in component list for
platform and cpu dai before soundcard registration.
Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The scmi-cpufreq driver calls the arch_set_freq_scale() callback on
frequency changes to provide scale-invariant load-tracking signals to
the scheduler. However, in the slow path, it does so while specifying
the current and max frequencies in different units, hence resulting in a
broken freq_scale factor.
Fix this by passing all frequencies in KHz, as stored in the CPUFreq
frequency table.
Fixes: 99d6bdf338 (cpufreq: add support for CPU DVFS based on SCMI message protocol)
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: 4.17+ <stable@vger.kernel.org> # v4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Old cpuidle/sysfs.txt file was replaced in aa5eee355b. So, refer to
an updated file.
Fixes: aa5eee355b (Documentation: admin-guide: PM: Add cpuidle document)
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit 815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h
mutually exclusive") clang no longer reuses the OPTIMIZER_HIDE_VAR macro
from compiler-gcc - instead it gets the version in
include/linux/compiler.h. Unfortunately that version doesn't actually
prevent compiler from optimizing out the variable.
Fix up by moving the macro out from compiler-gcc.h to compiler.h.
Compilers without incline asm support will keep working
since it's protected by an ifdef.
Also fix up comments to match reality since we are no longer overriding
any macros.
Build-tested with gcc and clang.
Fixes: 815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h mutually exclusive")
Cc: Eli Friedman <efriedma@codeaurora.org>
Cc: Joe Perches <joe@perches.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Accessing per-CPU variables is done by finding the offset of the
variable in the per-CPU block and adding it to the address of the
respective CPU's block.
Section 3.10.8 of ld.bfd's documentation states:
For expressions involving numbers, relative addresses and absolute
addresses, ld follows these rules to evaluate terms:
Other binary operations, that is, between two relative addresses
not in the same section, or between a relative address and an
absolute address, first convert any non-absolute term to an
absolute address before applying the operator."
Note that LLVM's linker does not adhere to the GNU ld's implementation
and as such requires implicitly-absolute terms to be explicitly marked
as absolute in the linker script. If not, it fails currently with:
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:153: at least one side of the expression must be absolute
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:154: at least one side of the expression must be absolute
Makefile:1040: recipe for target 'vmlinux' failed
This is not a functional change for ld.bfd which converts the term to an
absolute symbol anyways as specified above.
Based on a previous submission by Tri Vo <trong@android.com>.
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Rafael Ávila de Espíndola <rafael@espindo.la>
[ Update commit message per Boris' and Michael's suggestions. ]
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
[ Massage commit message more, fix typos. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Dmitry Golovin <dima@golovin.in>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Cao Jin <caoj.fnst@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tri Vo <trong@android.com>
Cc: dima@golovin.in
Cc: morbo@google.com
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181219190145.252035-1-ndesaulniers@google.com
Because "ethernet0" alias is missing, U-Boot doesn't generate board
specific MAC address. Effect of this is random MAC address every boot
and thus new IP address is assigned to the board.
Fix this by adding alias.
Fixes: 7389172fc3 ("ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Maxime: Removed unneeded comment]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The osc24M clock does not have a "clock-output-names" property, which
means that the clock name is derived from the node name in Linux. The
node name was changed in commit acfd5bbe26 ("ARM: dts: sun6i: Change
clock node names to avoid warnings"). This breaks Linux as the sunxi-ng
clock driver implicitly depends on the external clock being named
"osc24M".
Add a "clock-output-names" property to restore the previous behavior.
Fixes: acfd5bbe26 ("ARM: dts: sun6i: Change clock node names to avoid
warnings")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
tc358767 driver sets the connector type always to eDP.
This patch sets the type to DP if there is no panel defined, which
implies that there's a DP connector on the board.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-8-tomi.valkeinen@ti.com
The H and V syncs of the DP output are always set to active high. This
patch fixes the syncs by configuring them according to the videomode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-7-tomi.valkeinen@ti.com
The current driver accepts any videomode with pclk < 154MHz. This is not
correct, as with 1 lane and/or 1.62Mbps speed not all videomodes can be
supported.
Add code to reject modes that require more bandwidth that is available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-6-tomi.valkeinen@ti.com
Initially DP0_SRCCTRL is set to a static value which includes
DP0_SRCCTRL_LANES_2 and DP0_SRCCTRL_BW27, even when only 1 lane of
1.62Gbps speed is used. DP1_SRCCTRL is configured to a magic number.
This patch changes the configuration as follows:
Configure DP0_SRCCTRL by using tc_srcctrl() which provides the correct
value.
DP1_SRCCTRL needs two bits to be set to the same value as DP0_SRCCTRL:
SSCG and BW27. All other bits can be zero.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-5-tomi.valkeinen@ti.com
tc358767 driver does not set DRM bus_flags, even if it does configures
the polarity settings into its registers. This means that the DPI source
can't configure the polarities correctly.
Add sync flags accordingly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-2-tomi.valkeinen@ti.com
Add support for PMIC MIPI sequences using the new
intel_soc_pmic_exec_mipi_pmic_seq_element function.
This fixes the DSI LCD panel not lighting up when not initialized by the
GOP (because an external monitor was connected) on GPD win and GPD pocket
devices.
Specifically the LCD panel seems to need GPIO pin 9 on the PMIC to be
driven high, which is done through a PMIC MIPI sequence. Before this commit
if the sequence was not executed by the GOP the pin would stay low causing
the LCD panel to not work. Having the MIPI sequences properly control this
GPIO should also help save some power when the panel is off.
Changes in v2, v3:
-Only changes to other patches in this patch-set
Changes in v4:
-Move decoding of the raw 15 bytes PMIC MIPI sequence element into
i2c-address, register-address, value and mask into the mipi_exec_pmic()
function instead of passing the raw data to
intel_soc_pmic_exec_mipi_pmic_seq_element()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107111556.4510-5-hdegoede@redhat.com
Most PMIC-s use only a single i2c-address, so after verifying the
i2c-address matches, we can simply pass the call to regmap_update_bits.
This commit adds support for this and hooks this up for the xpower AXP288
PMIC by setting the new pmic_i2c_address field.
This fixes the following errors on display on / off on a Jumper Ezpad
mini 3 and an Onda V80 plus tablet, both of which use the AXP288:
intel_soc_pmic_exec_mipi_pmic_seq_element: Not implemented
intel_soc_pmic_exec_mipi_pmic_seq_element: i2c-addr: 0x34 reg-addr ...
[drm:mipi_exec_pmic [i915]] *ERROR* mipi_exec_pmic failed, error: -95
Instead of these errors on both devices we now correctly turn on / off
DLDO3 (through direct register manipulation). On the Onda V80 plus this
fixes an issue with the backlight being brighter around the borders after
an off / on cycle. This should also help to save some power when the
display is off.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107111556.4510-4-hdegoede@redhat.com
