Add initialization of each PCIe port reading and initializing
data using device tree.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no searon for u64 var cast to unsigned long long type.
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPU-selection code in sync_rcu_exp_select_cpus() disables preemption
to prevent the cpu_online_mask from changing. However, this relies on
the stop-machine mechanism in the CPU-hotplug offline code, which is not
desirable (it would be good to someday remove the stop-machine mechanism).
This commit therefore instead uses the relevant leaf rcu_node structure's
->ffmask, which has a bit set for all CPUs that are fully functional.
A given CPU's bit is cleared very early during offline processing by
rcutree_offline_cpu() and set very late during online processing by
rcutree_online_cpu(). Therefore, if a CPU's bit is set in this mask, and
preemption is disabled, we have to be before the synchronize_sched() in
the CPU-hotplug offline code, which means that the CPU is guaranteed to be
workqueue-ready throughout the duration of the enclosing preempt_disable()
region of code.
This also has the side-effect of using WORK_CPU_UNBOUND if all the CPUs for
this leaf rcu_node structure are offline, which is an acceptable difference
in behavior.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Bitwise operation is a little faster.
So I replace after() with using the flag FLAG_SND_UNA_ADVANCED as it is
already set before.
In addtion, there's another similar improvement in tcp_cwnd_reduction().
Cc: Joe Perches <joe@perches.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If sch_fq is used at ingress, skbs that might have been
timestamped by net_timestamp_set() if a packet capture
is requesting timestamps could be delayed by arbitrary
amount of time, since sch_fq time base is MONOTONIC.
Fix this problem by moving code from sch_netem.c to act_mirred.c.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
net: dsa: mv88e6xxx: Support more SERDES interfacxes
Currently the SERDES interfaces for ports 9 and 10 on the mv88e6390x
are supported, allowing upto 10G. However, when unused, these SERDES
interfaces can be used by some of the lower ports for 1000Base-X.
The tricky bit here is ordering. The SERDES have to become free from
ports 9 or 10 before they can be used with lower ports. Normally, this
would happen only when these ports would be configured up, which is
too late. So at probe time, defaulting ports 9 and 10 to 1000BaseX
frees them for use with lower ports. If they are actually needed, they
will be taken back when port 9 and 10 goes up.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.
The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.
For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
net: phy: convert advertise and supported to linkmode
This is the last part in converting phylib to make use of a linux
bitmap, not a u32, to represent links modes. This will allow support
for PHYs > 1Gbps, which need to use link modes represented by a bit >
32.
A number of MAC and PHY drivers need changes to support this. However
the previous two patchesets reduced the number somewhat, the helpers
which were introduced have been modified instead of the actual
drivers.
The follow on patches then make use of the extra bits, adding support
for more link modes.
Given how invasive this change is, i expect the build is broken for
some architectures i did not test. I will fixup the breakage as fast
as i can.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 2.5G and 5G can be represented in phydev->advertising and
phydev->lp_advertising, add these two links modes as possible
resolutions to auto negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that PHYs and MAC can support more than 32 bit masks, add link
modes which are > 31 to the PHY settings table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both states aren't used. Most likely they result from an idea that
never materialized. So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link failure is detected locally, the link is reset, the flag
link->in_session is set to false, and a RESET_MSG with the 'stopping'
bit set is sent to the peer.
The purpose of this bit is to inform the peer that this endpoint just
is going down, and that the peer should handle the reception of this
particular RESET message as a local failure. This forces the peer to
accept another RESET or ACTIVATE message from this endpoint before it
can re-establish the link. This again is necessary to ensure that
link session numbers are properly exchanged before the link comes up
again.
If a failure is detected locally at the same time at the peer endpoint
this will do the same, which is also a correct behavior.
However, when receiving such messages, the endpoints will not
distinguish between 'stopping' RESETs and ordinary ones when it comes
to updating session numbers. Both endpoints will copy the received
session number and set their 'in_session' flags to true at the
reception, while they are still expecting another RESET from the
peer before they can go ahead and re-establish. This is contradictory,
since, after applying the validation check referred to below, the
'in_session' flag will cause rejection of all such messages, and the
link will never come up again.
We now fix this by not only handling received RESET/STOPPING messages
as a local failure, but also by omitting to set a new session number
and the 'in_session' flag in such cases.
Fixes: 7ea817f4e8 ("tipc: check session number before accepting link protocol messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snmp_counter.rst explains the meanings of snmp counters. It also
provides a set of experiments (only 1 for this initial patch),
combines the experiments' resutls and the snmp counters'
meanings. This is an initial path, only explains a part of IP/ICMP
counters and provide a simple ping test.
Signed-off-by: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the broadcast retransmission algorithm is using the
'prev_retr' field in struct tipc_link to time stamp the latest broadcast
retransmission occasion. This helps to restrict retransmission of
individual broadcast packets to max once per 10 milliseconds, even
though all other criteria for retransmission are met.
We now move this time stamp to the control block of each individual
packet, and remove other limiting criteria. This simplifies the
retransmission algorithm, and eliminates any risk of logical errors
in selecting which packets can be retransmitted.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: LUU Duc Canh <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: sched: indirect tc block cb registration
John says:
This patchset introduces an alternative to egdev offload by allowing a
driver to register for block updates when an external device (e.g. tunnel
netdev) is bound to a TC block. Drivers can track new netdevs or register
to existing ones to receive information on such events. Based on this,
they may register for block offload rules using already existing
functions.
The patchset also implements this new indirect block registration in the
NFP driver to allow the offloading of tunnel rules. The use of egdev
offload (which is currently only used for tunnel offload) is subsequently
removed.
RFC v2 -> PATCH
- removed embedded tracking function from indir block register (now up to
driver to clean up after itself)
- refactored NFP code due to recent submissions
- removed priv list clean function in NFP (list should be cleared by
indirect block unregisters)
RFC v1->v2:
- free allocated owner struct in block_owner_clean function
- add geneve type helper function
- move test stub in NFP (v1 patch 2) to full tunnel offload
implementation via indirect blocks (v2 patches 3-8)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to NFP mean that stats updates from fw to driver no longer
require a flow lookup and (because egdev offload has been removed) the
ingress netdev for a lookup is now always known.
Remove obsolete code in a flow lookup that matches on host context and
that allows for a netdev to be NULL.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, only tunnel decap rules required egdev registration for
offload in NFP. These are now supported via indirect TC block callbacks.
Remove the egdev code from NFP.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, TC block tunnel decap rules were only offloaded when a
callback was triggered through registration of the rules egress device.
This meant that the driver had no access to the ingress netdev and so
could not verify it was the same tunnel type that the rule implied.
Register tunnel devices for indirect TC block offloads in NFP, giving
access to new rules based on the ingress device rather than egress. Use
this to verify the netdev type of VXLAN and Geneve based rules and offload
the rules to HW if applicable.
Tunnel registration is done via a netdev notifier. On notifier
registration, this is triggered for already existing netdevs. This means
that NFP can register for offloads from devices that exist before it is
loaded (filter rules will be replayed from the TC core). Similarly, on
notifier unregister, a call is triggered for each currently active netdev.
This allows the driver to unregister any indirect block callbacks that may
still be active.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the actions and tunnel_conf files contain local functions that check
the type of an input netdev. In preparation for re-use with tunnel offload
via indirect blocks, move these to static inline functions in a header
file.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the offload functions in NFP assumed that the ingress (or
egress) netdev passed to them was an nfp repr.
Modify the driver to permit the passing of non repr netdevs as the ingress
device for an offload rule candidate. This may include devices such as
tunnels. The driver should then base its offload decision on a combination
of ingress device and egress port for a rule.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers can register to receive TC block bind/unbind callbacks
by implementing the setup_tc ndo in any of their given netdevs. However,
drivers may also be interested in binds to higher level devices (e.g.
tunnel drivers) to potentially offload filters applied to them.
Introduce indirect block devs which allows drivers to register callbacks
for block binds on other devices. The callback is triggered when the
device is bound to a block, allowing the driver to register for rules
applied to that block using already available functions.
Freeing an indirect block callback will trigger an unbind event (if
necessary) to direct the driver to remove any offloaded rules and unreg
any block rule callbacks. It is the responsibility of the implementing
driver to clean any registered indirect block callbacks before exiting,
if the block it still active at such a time.
Allow registering an indirect block dev callback for a device that is
already bound to a block. In this case (if it is an ingress block),
register and also trigger the callback meaning that any already installed
rules can be replayed to the calling driver.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct function name and spelling/typo for device_block_probing()
in drivers/base/dd.c.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The simple_strtol() function is deprecated, use kstrtoint() instead.
Signed-off-by: Muchun Song <smuchun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiner Kallweit says:
====================
net: phy: add macros for PHYID matching in PHY driver config
Add macros for PHYID matching to be used in PHY driver configs.
By using these macros some boilerplate code can be avoided.
Use them initially in the Realtek PHY drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new macros for PHYID matching to avoid boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macros for PHYID matching to be used in PHY driver configs.
By using these macros some boilerplate code can be avoided.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: further phylib simplifications after recent changes to the state machine
After the recent changes to the state machine phylib can be further
simplified (w/o having to make any assumptions).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phy_mac_interrupt() doesn't call phy_change() any longer it's
called from phy_interrupt() only. Therefore phy_interrupt_is_valid()
returns true always and the check can be removed.
In case of PHY_HALTED phy_interrupt() bails out immediately,
therefore the second check for PHY_HALTED including the call to
phy_disable_interrupts() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State PHY_CHANGELINK isn't needed here, we can call the state machine
directly. We just have to remove the check for phy_polling_mode() to
make this work also in interrupt mode. Removing this check doesn't
cause any overhead because when not polling the state machine is
called only if required by some event.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
This allows to remove this flag from all driver configs.
v2:
- add helper for check in patch 1
- remove PHY_HAS_INTERRUPT from all drivers, not only Realtek
- remove flag PHY_HAS_INTERRUPT completely
v3:
- rebase patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was trying to solve a double free but I introduced a more serious
NULL dereference bug. The problem is that if there is an IRQ which
triggers immediately, then we need "info->uio_dev" but it's not set yet.
This patch puts the original initialization back to how it was and just
sets info->uio_dev to NULL on the error path so it should solve both
the Oops and the double free.
Fixes: f019f07ecf ("uio: potential double frees if __uio_register_device() fails")
Reported-by: Mathias Thore <Mathias.Thore@infinera.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Mathias Thore <Mathias.Thore@infinera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where eq->fw->size > PAGE_SIZE the error return rc
is being set to EINVAL however this is being overwritten to
rc = req->fw->size because the error exit path via label 'out' is
not being taken. Fix this by adding the jump to the error exit
path 'out'.
Detected by CoverityScan, CID#1453465 ("Unused value")
Fixes: c92316bf8e ("test_firmware: add batched firmware tests")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVMEM DT support seems to be totally broken after
commit e888d445ac ("nvmem: resolve cells from DT at registration time")
Fix this!
Index used in of_nvmem_cell_get() to find cell is specific to
consumer, It can not be used for searching the cell in provider.
Use device_node instead of this to find the matching cell in device
tree case.
Fixes: e888d445ac ("nvmem: resolve cells from DT at registration time")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After building the kernel with Clang, the following section mismatch
warning appears:
WARNING: vmlinux.o(.text+0x3bf19a6): Section mismatch in reference from
the function ssc_probe() to the function
.init.text:atmel_ssc_get_driver_data()
The function ssc_probe() references
the function __init atmel_ssc_get_driver_data().
This is often because ssc_probe lacks a __init
annotation or the annotation of atmel_ssc_get_driver_data is wrong.
Remove __init from atmel_ssc_get_driver_data to get rid of the mismatch.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
req.gid can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
vers/misc/sgi-gru/grukdump.c:200 gru_dump_chiplet_request() warn:
potential spectre issue 'gru_base' [w]
Fix this by sanitizing req.gid before calling macro GID_TO_GRU, which
uses it to index gru_base.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In kvp_send_key(), we do need call process_ib_ipinfo() if
message->kvp_hdr.operation is KVP_OP_GET_IP_INFO, because it turns out
the userland hv_kvp_daemon needs the info of operation, adapter_id and
addr_family. With the incorrect fc62c3b197, the host can't get the
VM's IP via KVP.
And, fc62c3b197 added a "break;", but actually forgot to initialize
the key_size/value in the case of KVP_OP_SET, so the default key_size of
0 is passed to the kvp daemon, and the pool files
/var/lib/hyperv/.kvp_pool_* can't be updated.
This patch effectively rolls back the previous fc62c3b197, and
correctly fixes the "this statement may fall through" warnings.
This patch is tested on WS 2012 R2 and 2016.
Fixes: fc62c3b197 ("Drivers: hv: kvp: Fix two "this statement may fall through" warnings")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RD/WR pin and CONVST pin are logical inputs to the AD78xx
chip as per the datasheet. Hence convert them to outputs.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD7818 does not support busy_pin functionality as per datasheet.
Hence drop busy_pin when AD7818 is used.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
