Commit graph

932,869 commits

Author SHA1 Message Date
Maciej W. Rozycki
3f2aa244ee
TC: Set DMA masks for devices
Fix a TURBOchannel support regression with commit 205e1b7f51
("dma-mapping: warn when there is no coherent_dma_mask") that caused
coherent DMA allocations to produce a warning such as:

defxx: v1.11 2014/07/01  Lawrence V. Stefani and others
tc1: DEFTA at MMIO addr = 0x1e900000, IRQ = 20, Hardware addr = 08-00-2b-a3-a3-29
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 dfx_dev_register+0x670/0x678
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #2
Stack : ffffffff8009ffc0 fffffffffffffec0 0000000000000000 ffffffff80647650
        0000000000000000 0000000000000000 ffffffff806f5f80 ffffffffffffffff
        0000000000000000 0000000000000000 0000000000000001 ffffffff8065d4e8
        98000000031b6300 ffffffff80563478 ffffffff805685b0 ffffffffffffffff
        0000000000000000 ffffffff805d6720 0000000000000204 ffffffff80388df8
        0000000000000000 0000000000000009 ffffffff8053efd0 ffffffff806657d0
        0000000000000000 ffffffff803177f8 0000000000000000 ffffffff806d0000
        9800000003078000 980000000307b9e0 000000001e900000 ffffffff80067940
        0000000000000000 ffffffff805d6720 0000000000000204 ffffffff80388df8
        ffffffff805176c0 ffffffff8004dc78 0000000000000000 ffffffff80067940
        ...
Call Trace:
[<ffffffff8004dc78>] show_stack+0xa0/0x130
[<ffffffff80067940>] __warn+0x128/0x170
---[ end trace b1d1e094f67f3bb2 ]---

This is because the TURBOchannel bus driver fails to set the coherent
DMA mask for devices enumerated.

Set the regular and coherent DMA masks for TURBOchannel devices then,
observing that the bus protocol supports a 34-bit (16GiB) DMA address
space, by interpreting the value presented in the address cycle across
the 32 `ad' lines as a 32-bit word rather than byte address[1].  The
architectural size of the TURBOchannel DMA address space exceeds the
maximum amount of RAM any actual TURBOchannel system in existence may
have, hence both masks are the same.

This removes the warning shown above.

References:

[1] "TURBOchannel Hardware Specification", EK-369AA-OD-007B, Digital
    Equipment Corporation, January 1993, Section "DMA", pp. 1-15 -- 1-17

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20835/
Fixes: 205e1b7f51 ("dma-mapping: warn when there is no coherent_dma_mask")
Cc: stable@vger.kernel.org # 4.16+
Cc: Ralf Baechle <ralf@linux-mips.org>
2018-10-11 09:16:44 -07:00
Mimi Zohar
34bccd61b1 MAINTAINERS: add Jarkko as maintainer for trusted keys
Trusted keys are variable length random numbers generated by the TPM,
which are used as symmetric keys.  The trusted key is never exported
to userspace in the clear.

Adding Jarrko, the TPM maintainer.

Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
2018-10-11 12:10:16 -04:00
Mike Snitzer
953923c09f dm: rename DM_TYPE_MQ_REQUEST_BASED to DM_TYPE_REQUEST_BASED
Now that request-based DM is only using blk-mq, there is no need to
differentiate between legacy "rq" and new "mq".  We're back to a single
request-based DM -- and there was much rejoicing!

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
2018-10-11 11:36:09 -04:00
Jens Axboe
6a23e05c2f dm: remove legacy request-based IO path
dm supports both, and since we're killing off the legacy path in
general, get rid of it in dm.

Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
2018-10-11 11:36:09 -04:00
Kees Cook
0bb95f80a3 Makefile: Globally enable VLA warning
Now that Variable Length Arrays (VLAs) have been entirely removed[1]
from the kernel, enable the VLA warning globally. The only exceptions
to this are the KASan an UBSan tests which are explicitly checking that
VLAs trigger their respective tests.

[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Airlie <airlied@linux.ie>
Cc: linux-kbuild@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Kees Cook <keescook@chromium.org>
2018-10-11 08:17:50 -07:00
Masahiro Yamada
81b4568348 compiler.h: give up __compiletime_assert_fallback()
__compiletime_assert_fallback() is supposed to stop building earlier
by using the negative-array-size method in case the compiler does not
support "error" attribute, but has never worked like that.

You can simply try:

    BUILD_BUG_ON(1);

GCC immediately terminates the build, but Clang does not report
anything because Clang does not support the "error" attribute now.
It will later fail at link time, but __compiletime_assert_fallback()
is not working at least.

The root cause is commit 1d6a0d19c8 ("bug.h: prevent double evaluation
of `condition' in BUILD_BUG_ON").  Prior to that commit, BUILD_BUG_ON()
was checked by the negative-array-size method *and* the link-time trick.
Since that commit, the negative-array-size is not effective because
'__cond' is no longer constant.  As the comment in <linux/build_bug.h>
says, GCC (and Clang as well) only emits the error for obvious cases.

When '__cond' is a variable,

    ((void)sizeof(char[1 - 2 * __cond]))

... is not obvious for the compiler to know the array size is negative.

Reverting that commit would break BUILD_BUG() because negative-size-array
is evaluated before the code is optimized out.

Let's give up __compiletime_assert_fallback().  This commit does not
change the current behavior since it just rips off the useless code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
2018-10-11 08:17:50 -07:00
Chris Wilson
0b4bf7ca9b drm/i915/selftests: Disable shrinker across mmap-exhaustion
For mmap-exhaustion, we deliberately put the system under a large amount
of pressure to ensure that we are able to reap mmap-offsets from dead
objects. If background activity does that reaping for us, that defeats
the purpose of the test and in some cases will fail our sanity checks
(because of the fake activity we use to prevent the idle worker).

Fixes: 932cac10c8 ("drm/i915/selftests: Prevent background reaping of acti
ve objects")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181011103748.18387-1-chris@chris-wilson.co.uk
2018-10-11 16:04:09 +01:00
Mikhail Zaslonko
5eaf436e0e s390/vmalloc: fix VMALLOC_START calculation
With the introduction of the module area on top of the vmalloc area, the
calculation of VMALLOC_START in setup_memory_end() function hasn't been
adjusted. As a result we got vmalloc area 2 Gb (MODULES_LEN) smaller than
it should be and the preceding vmemmap area got extra memory instead.
The patch fixes this calculation error although there were no visible
negative effects.
Apart from that, change 'tmp' variable to 'vmemmap' in memory_end
calculation for better readability.

Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-11 17:02:38 +02:00
Ryan Lee
a23f5dc844
ASoC: max98373: Sort DHT Rot Pnt Volume in reverse order
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:37:39 +01:00
Ryan Lee
d34c8f37c7
ASoC: max98373: Sort max98373_bde_gain_tlv in reverse order
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:37:38 +01:00
Ryan Lee
6c3beeca42
ASoC: max98373: Sort BDE Limiter Thresh Volume in reverse order
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:37:38 +01:00
Ryan Lee
4cbbc91609
ASoC: max98373: Sort Digital Volume in reverse order
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:37:36 +01:00
Lubomir Rintel
44221ebae2
spi/spi-pxa2xx: add PXA2xx SSP SPI Controller
This is the SPI controller found on Marvel MMP2 and perhaps more
platforms.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:37:21 +01:00
Lubomir Rintel
87ae1d2d70
spi: pxa2xx: Add devicetree support
The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:28:04 +01:00
Lubomir Rintel
55ef8262f2
spi: pxa2xx: Use an enum for type
That seems to be the correct type.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:28:03 +01:00
Girish Mahadevan
561de45f72
spi: spi-geni-qcom: Add SPI driver support for GENI based QUP
This driver supports GENI based SPI Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including SPI. This driver supports SPI
operations using FIFO mode of transfer.

Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:28:02 +01:00
Dilip Kota
4b8ce2f707
spi: soc: qcom: GENI SE SPI controller device tree binding
Move GENI SE SPI controller device-tree bindings
from devicetree/bindings/soc/qcom/qcom,geni-se.txt
to devicetree/bindings/spi/qcom,spi-geni-qcom.txt.

Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:28:01 +01:00
Vladimir Zapolskiy
f4f9554f16 MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture
To all appearance Joachim Eastwood abandoned the maintenance of NXP
LPC18xx/LPC43xx archtecture about two years ago, and for me it would be
possible to continue the support, fortunately the quality of platform
drivers written by Joachim is exceptionally high.

The change is based on https://lkml.org/lkml/2018/9/24/1398 discussion.

At the same time two redundant explicit driver file paths are dropped
from the list, clk-lpc18xx* drivers are covered by "lpc18xx" search
pattern and timer-lpc32xx driver is covered by "lpc32xx" pattern and it
goes into ARM/LPC32XX entry, which is also under my wing, in other words
LPC18xx/LPC43xx clocksource and CCF drivers will remain maintained.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-10-11 16:27:58 +02:00
Dilip Kota
a8a398b833
dt-bindings: soc: qcom: Remove SPI controller maximum frequency binding
SPI controller driver should maintain the maximum frequency
of the controller instead of relying on device tree bindings.
Because maximum frequency is specific property of SPI
controller.

Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:27:57 +01:00
Emil Renner Berthing
a3c174021c
spi: rockchip: simplify spi enable logic
Let the dma/non-dma code paths handle the spi enable
flag themselves. This removes some logic to determine
if the flag should be turned on before or after dma
and also don't leave the spi enabled if the dma path
fails.

Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:17:45 +01:00
Emil Renner Berthing
d9071b7e9f
spi: rockchip: directly use direction constants
The dma direction for the tx and rx dma channels never
change, so just use the constants directly rather
than storing them in device data.

Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:17:31 +01:00
Emil Renner Berthing
f340b92051
spi: rockchip: mark use_dma as bool
The driver data has a u32 field use_dma which is
only ever used as a boolean, so change its type
to reflect that.

Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:17:16 +01:00
Emil Renner Berthing
058f7c509e
spi: rockchip: remove unneeded dma_caps
We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.

Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:17:01 +01:00
Huibin Hong
dcfc861d24
spi: rockchip: adjust dma watermark and burstlen
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.

Clamp rx burst length to 1 to avoid alignment issues.

Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:14:37 +01:00
Jiri Olsa
94aafb74ce perf vendor events intel: Fix wrong filter_band* values for uncore events
Michael reported that he could not stat following event:

  $ perf stat -e unc_p_freq_ge_1200mhz_cycles -a -- ls
  event syntax error: '..e_1200mhz_cycles'
                                    \___ value too big for format, maximum is 255
  Run 'perf list' for a list of valid events

The event is unwrapped into:

  uncore_pcu/event=0xb,filter_band0=1200/

where filter_band0 format says it's one byte only:

  # cat uncore_pcu/format/filter_band0
  config1:0-7

while JSON files specifies bigger number:

  "Filter": "filter_band0=1200",

all the filter_band* formats show 1 byte width:

  # cat uncore_pcu/format/filter_band1
  config1:8-15
  # cat uncore_pcu/format/filter_band2
  config1:16-23
  # cat uncore_pcu/format/filter_band3
  config1:24-31

The reason of the issue is that filter_band* values are supposed to be
in 100Mhz units.. it's stated in the JSON help for the events, like:

  filter_band3=XXX, with XXX in 100Mhz units

This patch divides the filter_band* values by 100, plus there's couple
of changes that actually change the number completely, like:

  -        "Filter": "edge=1,filter_band2=4000",
  +        "Filter": "edge=1,filter_band2=30",

Reported-by: Michael Petlan <mpetlan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20181010080339.GB15790@krava
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2018-10-11 11:13:23 -03:00
Huibin Hong
dd8fd2cbc7
spi: rockchip: initialize dma_slave_config properly
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.

Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:11:45 +01:00
Girish Mahadevan
04000dc6f7
spi: Introduce new driver for Qualcomm QuadSPI controller
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.

Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:11:09 +01:00
Girish Mahadevan
db117f5f42
spi: Qualcomm Quad SPI(QSPI) documentation
Bindings for Qualcomm Quad SPI used on SoCs such as sdm845.

Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:11:05 +01:00
Talel Shenhar
f2d7047948
dw: spi: add support for Amazon's Alpine spi controller
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree.  Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.

Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:11:04 +01:00
Talel Shenhar
d49a303667
spi: dw: add compatible for Amazon's Alpine spi controller
This compatible adds the ability for dw spi controller driver to work with
the dw spi controller found on Alpine chips.

The dw spi controller has an auto-deselect of Chip-Select, in case there is
no data inside the Tx FIFO. While working on platforms with Alpine chips,
auto-deselect mode causes an issue for some spi devices that can't handle
the Chip-Select deselect in the middle of a transaction. It is a normal
behavior for a Tx FIFO to be empty in the middle of a transaction, due to
busy cpu. In the Alpine chip family an option to change the default
behavior was added to the original dw spi controller to prevent this issue
of de-asserting Chip-Select once TX FIFO is empty. The change was to allow
SW manual control of the Chip-Select. With this change, as long as the
Slave Enable Register is asserted, the Chip-Select will be asserted. As a
result, it is necessary to deselect the Slave Select Register once the
transaction is done. This feature is enabled via a new device compatible
string called 'amazon,alpine-dw-apb-ssi'.  Once the driver identifies the
new compatible string, it enables the hw fixup logic, by writing to a
dedicated register found in the IP reserved area and will start manual
deselecting the Slave Select Register when the transfer ends.

Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-10-11 15:11:00 +01:00
Arnd Bergmann
be59a3282c SoCFPGA DTS updates for v4.20, part 3
- Add ethernet aliases for Stratix10
 - Move ethernet aliases from socfpga dtsi
 - Correct system manager register size for Stratix10
 - Correct SDRAM node address for Arria10
 -----BEGIN PGP SIGNATURE-----
 
 iQJIBAABCgAyFiEEoHhMeiyk5VmwVMwNGZQEC4GjKPQFAlu+E5kUHGRpbmd1eWVu
 QGtlcm5lbC5vcmcACgkQGZQEC4GjKPQxVBAApS3jzuE6jofUL2CXccl8DGuHJ5Ur
 FV3qPKtHB5Zd44VxRk12SODKBED4ry8+vzixvF4+jryvXkXsUXB76p0h4zcmpb2g
 L1Ngl5S8LW0ES74Rr2BMglSPmabjGOK7mSqj+CREwsOmWufZXQkpPV1ytbqscqTt
 S0bXRjChFhvbyc5qJ9NGx96sFpqfAL4SXpb8s9+3nfs8K5BUxI4RQD4zQtr03Fk1
 7wHUo2m0eyQGtTGR8Euml73ZyYdJn3e9Tcfl0vNRcL36/yr/qlA4St7EjscuoUDc
 XBBFydoo8pZUKEHLkAo6m+nSFdDoap048cKf47OLA0R18tSNauknCjkJniftx6JM
 LdD+T/YDRMqXgA7AXPkGwtApVKymJVmVmh4yuyNtqkQ5GGAZu6jCYo7UnEhfAkoQ
 ml20lH+O0WkcyRSrokUQHm8v+xVYt9m21xkS7NaQzCcCwX2LVNJVsXNVDMHlkFvM
 Sm6xK7v1QCT4cst6wtJlE0NHyBRzer+GpP6xH7F57rUrTy99Hfb2wcQ4vN80sFep
 BkGk5NL9OA/LQUweEoPqNGfASfs1YwTZp8od0fCKsQBybIBE4JrbKHGFj91X53SG
 MEMFo8PaNmzbnbopwlqlmUw6Bu58SknuC4H7/Az8ENLZc8AjK/iozR3efqsA759K
 eQqIqZbpW/xORnU=
 =S+pP
 -----END PGP SIGNATURE-----

Merge tag 'socfpga_updates_for_v4.20_part3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt

SoCFPGA DTS updates for v4.20, part 3
- Add ethernet aliases for Stratix10
- Move ethernet aliases from socfpga dtsi
- Correct system manager register size for Stratix10
- Correct SDRAM node address for Arria10

* tag 'socfpga_updates_for_v4.20_part3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: dts: socfgpa: remove ethernet aliases from dtsi
  arm64: dts: stratix10: add ethernet aliases
  arm64: dts: stratix10: Correct System Manager register size
  ARM: dts: socfpga: Fix SDRAM node address for Arria10

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-10-11 16:07:07 +02:00
Arnd Bergmann
ce57b60f38 Samsung DTS ARM64 changes for v4.20
1. Use graph between USB-PHY and MUIC.
 2. Cleanup of SD card detect pin level.
 -----BEGIN PGP SIGNATURE-----
 
 iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAlu+QZQQHGtyemtAa2Vy
 bmVsLm9yZwAKCRDBN2bmhouD12Y2D/9Y+btGTz/cP+VLMg4oQ+awJpbeCbX/i3qr
 4w9bpMTjPfS8J4bUprA1Ay/MbqeRtJgXxF8H+GvyWg/QPcaf8prsVIq2KQWM8yUa
 EWCoE+C+kDY4Q2ElDW8ftNmMFe4iTdsYgXpBuPFxP+7nK7fGEKutOVfIY4Mw9RcN
 R68nu7t7CJjJxKSAiTquGmrTXbO3QUA24uyxRLTaz7Wkrap4cvnu1kryqIA5ncmI
 ScOGiGxxv53gbK40ru8b1eVlVhlNSMgeh0S+NvqmR8r3AFAapmPgMzrMPL+2Y6Lh
 O6Diu/BNy1oqn/j9iXdTwLANWG/t+l/GdOb2TxXgHPpOG67VC5SIE8yJK9qmr82Q
 jC4r0jLGA7pbXbKtRvORVkT3fRro+8m1j0ATdH1DTWgEdjFG3LKJHThetntuK1pi
 EfHEmotrA6GlhYwUrXebrqeKEpEUT5uHjvGrQFlnJjWmkHGw2+cdIk1xzU5nAhTu
 NsctmUU/pMFabGaHZLHXgoXODom5QzZhoThFBLZiT36NeTlevrBH6K9qrYKzhUWk
 4q4BaivL0h6TyIm+TBROIWDGYdYC+MykVkcccUwCqzmRU/J1m71gpWjlm6AmL/IU
 qafQ57GArNJhplIfHHJjU4AXTdVrxNaClhHfc955mBO0ggx63skQvyoTHXL2zVkP
 wC4yNlxGIg==
 =9pHU
 -----END PGP SIGNATURE-----

Merge tag 'samsung-dt64-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Samsung DTS ARM64 changes for v4.20

1. Use graph between USB-PHY and MUIC.
2. Cleanup of SD card detect pin level.

* tag 'samsung-dt64-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  arm64: ARM: dts: exynos: Remove double SD card detect pin inversion on TM2
  arm64: dts: exynos: Add OF graph between USB-PHY and MUIC

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-10-11 16:06:17 +02:00
Arnd Bergmann
b483792c9e Samsung DTS ARM changes for v4.20, second round
Add proper configuration for Odroid XU SD write-protect pin.
 -----BEGIN PGP SIGNATURE-----
 
 iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAlu+QGMQHGtyemtAa2Vy
 bmVsLm9yZwAKCRDBN2bmhouD15EYD/sGn4Ggm+W2+TP5xhyxkJ8qlvrYv/30lt7b
 NC+X0sCptopbjrXZ/PylFExY4C+K9MrEX1BCt6IWjnJ6Pdm2D3Z/At9NZKYKW+18
 tWiu3g+tBcVInR5sfmEMboC/ELXM5Ly+UXEIzZTQ3bNuCdw74MF0AoW0o+JERnqC
 rImVneHDElAjky2YRV/jRVmDtRXZ4mlIS4YpMttvhIH3xXX1EPfcnt6tOCK2i9Ew
 +nKBUc/8+zUWfCeQLSvBrAz4FtKtDfmveVg5+OsY9Mq9FIlcLKp7zTt5T/gAUFEw
 9c4CxFF97mr0LubIUEwOslBIWyUNktPLxuCNKwN29BwTL7QoCaor9RFgvFB3fIqs
 2+qD4m5KCheTFjvL6XgYCoPRuMLlZ7kNz2EMQ5BQjkYyrVT4ZAvz5Zo5NFFJh/0z
 Mq0aPY1Ljsn0XyuaQa0W3obtWawZoOxvFVx3PWPNfEdYsg4l0U46fsj1dtGvz4eW
 dyfDp8BoUbMmiPKELrQ/ce5g87lFSWi8C7zHluUrkbtWhtJk4Z704LGdbyYMlj5i
 pXJ/ukH60s7fAWGWUvAvptsEZ9pczqqPTqS3XBRcc87C3tm7yKa8Caob/wb9DZZl
 jDC4/aFo1XX9bG6Gm+8tlt6gvONFeDknHRbA+ZkJMItqFulG1bcGxZoOqFsvlR3+
 0R3bCPHPcw==
 =RMAs
 -----END PGP SIGNATURE-----

Merge tag 'samsung-dt-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Samsung DTS ARM changes for v4.20, second round

Add proper configuration for Odroid XU SD write-protect pin.

* tag 'samsung-dt-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-10-11 16:04:13 +02:00
Mark Brown
93043b6749 Immutable branch for QCOM Geni patches
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJbqGxAAAoJEFKiBbHx2RXVIYwQAIzgqbC7mt4dwLB22OW1PCwG
 f/cFBEAegy9tWMr1cMAR0u+6mXIYZ3kxgTYCZN665Qj44TwfJKeks15ysE+NaWog
 gOKr40cedtOoIyNqy0D3JmUm1lB0x1bmD9E0NA8eAytHm0/29Ab4Xf7k1S77K7Sl
 6q+Bf/VnnxwFtQxvAd0dgpzIjptcOMfsJHt+O+PnyMONVb/aPFdQuA1MqSKO0Uwa
 kV7l1HRBg+sR6DlVvpx3b3LX73o9WDZfVziXvACb7tcVXuS4Z2BZ40k0Q8dMGeHJ
 dBcS7uDiyZ/PB7WqIqTDnS80lQAJkwiOY/pvwPYsjVxj4Ic+5YB4SUj6gSKwj46s
 k5pUvPZbcXaPri4klKGzMD7z8RfUjgWjg7bZTzrqE0VQCq7BxSUpeqkZ5Wc7GVro
 B2Mw9Q/0fAKMnP3wLpvp9roG6Pc135dm+RKHEsUZhNkOMnJRyKKgXs2AMV4ukhJk
 s4rcmADa8F6Vo0hIEUyHU/SzodJGFrQLDSmvzatmFiUgfHHlOysr6TCyldbBxBQz
 Tq40Jqz6oIl3bllt8dF7gEzh0bLlZnX88qFTuZJBV26IOfVRWBUfmZRs01Ls+0ba
 CcZtaKE9jRNFR3Eb6C86Nr3ua2TnoW+AnbG/0jySuGs+lOwHMA9fVl1Y6V3F0aPf
 QUvL/X6IXvneZ00wIaEg
 =tUbu
 -----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
 
 iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlu/V7YTHGJyb29uaWVA
 a2VybmVsLm9yZwAKCRAk1otyXVSH0JGRB/9XO5jr02nc6K1zDo1Y2zgNEgZzcSNB
 GxNXzRkUCZMQz/+miw0euSFLfrFIrk3AGo4nlz2NNtCdYmGTry+ZvxdTwkJuRi4A
 1/Xfz0ZkZQ7m1+R71wh7QB56cDY6LabJy91UFrjY3U7yQwhOE1iXZ+6k4evepKWT
 ceTcEMZ/TKtdbbbHJrmwiIU/BQAOp3gawfvtn+kRwrdH+b9g1f1IRUBAr7BAPC67
 Z58ELtX05vUe6SmeTaanVyq6xlmS6BcKu0d0sS7syAR0UjuHjJSLV99FxV8vyZLS
 jRJ15NkTc28qnNbik+PhVJ5MdsNwe03eOJaQad/wwWkBdqEZTU4NA1Ln
 =hwtp
 -----END PGP SIGNATURE-----

Merge tag 'qcom-geni-immutable-for-mark-brown' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into spi-4.20

Immutable branch for QCOM Geni patches
2018-10-11 15:01:24 +01:00
Jouni Malinen
efb543e61c mac80211: Extend SAE authentication in infra BSS STA mode
Previous implementation of SAE authentication in infrastructure BSS was
somewhat restricting and not exactly clean way of handling the two
auth() operations. This ended up removing and re-adding the STA entry
for the AP in the middle of authentication and also messing up
authentication state tracking through the sequence of four
Authentication frames. Furthermore, this did not work if the AP ended up
sending out SAE Confirm (auth trans #2) immediately after SAE Commit
(auth trans #1) before the station had time to transmit its SAE Confirm.

Clean up authentication state handling for the SAE case to allow two
rounds of auth() calls without dropping all state between those
operations. Track peer Confirmed status and mark authentication
completed only once both ends have confirmed.

ieee80211_mgd_auth() check for EBUSY cases is now handling only the
pending association (ifmgd->assoc_data) while all pending authentication
(ifmgd->auth_data) cases are allowed to proceed to allow user space to
start a new connection attempt from scratch even if the previously
requested authentication is still waiting completion. This is needed to
avoid making SAE error cases with retries take excessive amount of time
with no means for the user space to stop that (apart from setting the
netdev down).

As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up
to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing
SAE authentication since the new ieee80211_mark_sta_auth() helper
function can handle both completion of authentication and updates to the
STA entry under the same condition and there is no need to return from
the function between those operations.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:08 +02:00
Jouni Malinen
8d7432a2f5 mac80211: Move ieee80211_mgd_auth() EBUSY check to be before allocation
This makes it easier to conditionally replace full allocation of
auth_data to use reallocation for the case of continuing SAE
authentication. Furthermore, there was not really any point in having
this check done so late in the function after having already completed
number of steps that cannot be used anyway in the error case.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:07 +02:00
Jouni Malinen
fc107a9330 mac80211: Helper function for marking STA authenticated
Authentication exchange can be completed in both TX and RX paths for
SAE, so move this common functionality into a helper function to avoid
having to implement practically the same operations in two places when
extending SAE implementation in the following commits.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:05 +02:00
Felix Fietkau
506dbf90c1 mac80211: rc80211_minstrel: remove variance / stddev calculation
When there are few packets (e.g. for sampling attempts), the exponentially
weighted variance is usually vastly overestimated, making the resulting data
essentially useless. As far as I know, there has not been any practical use
for this, so let's not waste any cycles on it.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:05 +02:00
Felix Fietkau
f4ec7cb0f9 mac80211: minstrel: do not sample rates 3 times slower than max_prob_rate
These rates are highly unlikely to be used quickly, even if the link
deteriorates rapidly. This improves throughput in cases where CCK rates
are not reliable enough to be skipped entirely during sampling.
Sampling these rates regularly can cost a lot of airtime.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:04 +02:00
Felix Fietkau
972b66b86f mac80211: minstrel: fix sampling/reporting of CCK rates in HT mode
Long/short preamble selection cannot be sampled separately, since it
depends on the BSS state. Because of that, sampling attempts to
currently not used preamble modes are not counted in the statistics,
which leads to CCK rates being sampled too often.

Fix statistics accounting for long/short preamble by increasing the
index where necessary.
Fix excessive CCK rate sampling by dropping unsupported sample attempts.

This improves throughput on 2.4 GHz channels

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:03 +02:00
Felix Fietkau
80df9be67c mac80211: minstrel: fix CCK rate group streams value
Fixes a harmless underflow issue when CCK rates are actively being used

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:03 +02:00
Felix Fietkau
37439f2d6e mac80211: minstrel: fix using short preamble CCK rates on HT clients
mi->supported[MINSTREL_CCK_GROUP] needs to be updated
short preamble rates need to be marked as supported regardless of
whether it's currently enabled. Its state can change at any time without
a rate_update call.

Fixes: 782dda00ab ("mac80211: minstrel_ht: move short preamble check out of get_rate")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:02 +02:00
Felix Fietkau
202df504d7 mac80211: minstrel: reduce minstrel_mcs_groups size
By storing a shift value for all duration values of a group, we can
reduce precision by a neglegible amount to make it fit into a u16 value.
This improves cache footprint and reduces size:

Before:
   text    data     bss     dec     hex filename
  10024     116       0   10140    279c rc80211_minstrel_ht.o

After:
   text    data     bss     dec     hex filename
   9368     116       0    9484    250c rc80211_minstrel_ht.o

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:02 +02:00
Felix Fietkau
b1c4f68337 mac80211: minstrel: merge with minstrel_ht, always enable VHT support
Legacy-only devices are not very common and the overhead of the extra
code for HT and VHT rates is not big enough to justify all those extra
lines of code to make it optional.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:01 +02:00
Felix Fietkau
5b5e87314e mac80211: minstrel: remove unnecessary debugfs cleanup code
debugfs entries are cleaned up by debugfs_remove_recursive already.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:00 +02:00
Chaitanya T K
f458e832ba mac80211: minstrel: Enable STBC and LDPC for VHT Rates
If peer support reception of STBC and LDPC, enable them for better
performance.

Signed-off-by: Chaitanya TK <chaitanya.mgit@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:01:00 +02:00
Johannes Berg
42dca5ef24 mac80211: avoid reflecting frames back to the client
I'm not really sure exactly _why_ I've been carrying a note
for what's probably _years_ to check that we don't do this,
but we clearly do reflect frames back to the station itself
if it sends such.

One way or the other, it's useless since the station doesn't
really need the AP to talk to itself, so suppress it.

While at it, clarify some of the logic by removing skb->data
references in favour of the destination address (pointer) we
already have separately.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:00:59 +02:00
Johannes Berg
3d7af87835 nl80211: use netlink policy validation function for elements
Instead of open-coding a lot of calls to is_valid_ie_attr(),
add this validation directly to the policy, now that we can.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:00:59 +02:00
Johannes Berg
ab0d76f682 nl80211: use policy range validation where applicable
Many range checks can be done in the policy, move them
there. A few in mesh are added in the code (taken out of
the macros) because they don't fit into the s16 range in
the policy validation.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-10-11 16:00:58 +02:00
Rafał Miłecki
940ec770c2
spi: bcm-qspi: switch back to reading flash using smaller chunks
Fixing/optimizing bcm_qspi_bspi_read() performance introduced two
changes:
1) It added a loop to read all requested data using multiple BSPI ops.
2) It bumped max size of a single BSPI block request from 256 to 512 B.

The later change resulted in occasional BSPI timeouts causing a
regression.

For some unknown reason hardware doesn't always handle reads as expected
when using 512 B chunks. In such cases it may happen that BSPI returns
amount of requested bytes without the last 1-3 ones. It provides the
remaining bytes later but doesn't raise an interrupt until another LR
start.

Switching back to 256 B reads fixes that problem and regression.

Fixes: 345309fa7c ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
2018-10-11 15:00:34 +01:00