A DMM timeout "timed out waiting for done" has been observed on DRA7
devices. The timeout happens rarely, and only when the system is under
heavy load.
Debugging showed that the timeout can be made to happen much more
frequently by optimizing the DMM driver, so that there's almost no code
between writing the last DMM descriptors to RAM, and writing to DMM
register which starts the DMM transaction.
The current theory is that a wmb() does not properly ensure that the
data written to RAM is observable by all the components in the system.
This DMM timeout has caused interesting (and rare) bugs as the error
handling was not functioning properly (the error handling has been fixed
in previous commits):
* If a DMM timeout happened when a GEM buffer was being pinned for
display on the screen, a timeout error would be shown, but the driver
would continue programming DSS HW with broken buffer, leading to
SYNCLOST floods and possible crashes.
* If a DMM timeout happened when other user (say, video decoder) was
pinning a GEM buffer, a timeout would be shown but if the user
handled the error properly, no other issues followed.
* If a DMM timeout happened when a GEM buffer was being released, the
driver does not even notice the error, leading to crashes or hang
later.
This patch adds wmb() and readl() calls after the last bit is written to
RAM, which should ensure that the execution proceeds only after the data
is actually in RAM, and thus observable by DMM.
The read-back should not be needed. Further study is required to understand
if DMM is somehow special case and read-back is ok, or if DRA7's memory
barriers do not work correctly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/omapdrm/dss/dispc.c: In function 'dispc_ovl_setup_common':
drivers/gpu/drm/omapdrm/dss/dispc.c:2627:19: warning:
variable 'frame_height' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We prefer to use ERR_CAST to do so.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
tcm-sita.h is unused since commit 0d6fa53fd8 ("drm/omap: Use bitmaps for TILER placement")
Let's remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Thomas Falcon says:
====================
ibmvnic: Implement driver-defined queue limits
In this patch series, update the ibmvnic driver to use driver-defined
queue limits instead of limits imposed by the Virtual I/O server
management partition. For some deviced, initial max queue size and
amount limits, despite their definition, can actually be exceeded if
the client driver requests it. With this in mind, define a private
ethtool flag that toggles the use of driver-defined limits. These
limits are currently more than what supported hardware will likely
allow, so the driver will attempt to get as close as possible to
the user request but may not fully succeed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When choosing channel amounts and ring sizes, the maximums in the
ibmvnic driver are defined by the virtual i/o server management
partition. Even though they are defined as maximums, the client
driver may in fact successfully request resources that exceed
these limits, which are mostly dependent on a user's hardware
With this in mind, provide an ethtool flag that when enabled will
allow the user to request resources limited by driver-defined
maximums instead of limits defined by the management partition.
The driver will try to honor the user's request but may not allowed
by the management partition. In this case, the driver requests
as close as it can get to the desired amount until it succeeds.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce driver-defined maximums for queue ring sizes. Devices
available for IBM vNIC today will likely not allow this amount,
but this should give us some leeway for future devices that may
support larger ring sizes.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase queue size limit to 16. Devices available for IBM vNIC today
will not allow this amount, but this should give us some leeway for
future devices that may support more RX or TX queues.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the vDSO implementation of clock_gettime() is getting
reworked, add a selftest for it. This tests that its output is
consistent with the syscall version.
This is marked for stable to serve as a test for commit
715bd9d12f ("x86/vdso: Fix asm constraints on vDSO syscall fallbacks")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/082399674de2619b2befd8c0dde49b260605b126.1538422295.git.luto@kernel.org
Some of the chip-specific hw_start functions set bit TXCFG_AUTO_FIFO
in register TxConfig. The original patch changed the order of some
calls resulting in these changes being overwritten by
rtl_set_tx_config_registers() in rtl_hw_start(). This eventually
resulted in network stalls especially under high load.
Analyzing the chip-specific hw_start functions all chip version from
34, with the exception of version 39, need this bit set.
This patch moves setting this bit to rtl_set_tx_config_registers().
Fixes: 4fd48c4ac0 ("r8169: move common initializations to tp->hw_start")
Reported-by: Ortwin Glück <odi@odi.ch>
Reported-by: David Arendt <admin@prnet.org>
Root-caused-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Tony Atkinson <tatkinson@linux.com>
Tested-by: David Arendt <admin@prnet.org>
Tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syscall fallbacks in the vDSO have incorrect asm constraints.
They are not marked as writing to their outputs -- instead, they are
marked as clobbering "memory", which is useless. In particular, gcc
is smart enough to know that the timespec parameter hasn't escaped,
so a memory clobber doesn't clobber it. And passing a pointer as an
asm *input* does not tell gcc that the pointed-to value is changed.
Add in the fact that the asm instructions weren't volatile, and gcc
was free to omit them entirely unless their sole output (the return
value) is used. Which it is (phew!), but that stops happening with
some upcoming patches.
As a trivial example, the following code:
void test_fallback(struct timespec *ts)
{
vdso_fallback_gettime(CLOCK_MONOTONIC, ts);
}
compiles to:
00000000000000c0 <test_fallback>:
c0: c3 retq
To add insult to injury, the RCX and R11 clobbers on 64-bit
builds were missing.
The "memory" clobber is also unnecessary -- no ordering with respect to
other memory operations is needed, but that's going to be fixed in a
separate not-for-stable patch.
Fixes: 2aae950b21 ("x86_64: Add vDSO for x86-64 with gettimeofday/clock_gettime/getcpu")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/2c0231690551989d2fafa60ed0e7b5cc8b403908.1538422295.git.luto@kernel.org
Eric Dumazet says:
====================
tun: address two syzbot reports
Small changes addressing races discovered by syzbot.
First patch is a cleanup.
Second patch moves a mutex init sooner.
Third patch makes sure each tfile gets its own napi enable flags.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tun_napi_disable() and tun_napi_del() do not need
a pointer to the tun_struct
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link dumps can return results from a target namespace. If the namespace id
is invalid, then the dump request should fail if get_target_net fails
rather than continuing with a dump of the current namespace.
Fixes: 79e1ad148c ("rtnetlink: use netnsid to query interface")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 90c7afc96c.
When the commit was merged, the code used nf_ct_put() to free
the entry, but later on commit 76644232e6 ("openvswitch: Free
tmpl with tmpl_free.") replaced that with nf_ct_tmpl_free which
is a more appropriate. Now the original problem is removed.
Then 44d6e2f273 ("net: Replace NF_CT_ASSERT() with WARN_ON().")
replaced a debug assert with a WARN_ON() which is trigged now.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the recent TCP/EDT patch series, I switched TCP and sch_fq
clocks from MONOTONIC to TAI, in order to meet the choice done
earlier for sch_etf packet scheduler.
But sure enough, this broke some setups were the TAI clock
jumps forward (by almost 50 year...), as reported
by Leonard Crestez.
If we want to converge later, we'll probably need to add
an skb field to differentiate the clock bases, or a socket option.
In the meantime, an UDP application will need to use CLOCK_MONOTONIC
base for its SCM_TXTIME timestamps if using fq packet scheduler.
Fixes: 72b0094f91 ("tcp: switch tcp_clock_ns() to CLOCK_TAI base")
Fixes: 142537e419 ("net_sched: sch_fq: switch to CLOCK_TAI")
Fixes: fd2bca2aa7 ("tcp: switch internal pacing timer to CLOCK_TAI")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS test cases splice_from_pipe, send_and_splice &
recv_peek_multiple_records expect to receive a given nummber of bytes
and then compare them against the number of bytes which were sent.
Therefore, system call recv() must not return before receiving the
requested number of bytes, otherwise the subsequent memcmp() fails.
This patch passes MSG_WAITALL flag to recv() so that it does not return
prematurely before requested number of bytes are copied to receive
buffer.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RSC feature -- a bit field "internal" was added here with total
size unchanged:
struct rndis_per_packet_info {
u32 size;
u32 type:31;
u32 internal:1;
u32 ppi_offset;
};
On TX path, we put rndis msg into skb head room, which is not zeroed
before passing to us. We do not use the "internal" field in TX path,
but it may impact older hosts which use the entire 32 bits as "type".
To fix the bug, this patch sets the field "internal" to zero.
Fixes: c8e4eff467 ("hv_netvsc: Add support for LRO/RSC in the vSwitch")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using mod_delayed_work() allows to simplify handling delayed work and
removes the need for the sync parameter in phy_trigger_machine().
Also introduce a helper phy_queue_state_machine() to encapsulate the
low-level delayed work calls. No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: systemport: Turn on offloads by default
Up until now, we had added all the code necessary to turn on RX/TX
checksum offloads at runtime, but there is no reason why they have to be
disabled by default given that this gives a slight performance
improvement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When inserting the TSB, keep track of how many times we had to do it and
if there was a failure in doing so, this helps profile the driver for
possibly incorrect headroom settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During bcm_sysport_insert_tsb() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can turn on the RX/TX checksum offloads by default and make sure that
those are properly reflected back to e.g: stacked devices such as VLAN
or DSA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver resume and open, the HW may have lost its context/state,
utilize bcm_sysport_set_features() to make sure we do restore the
correct set of features that were previously configured.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally enabling TX and RX checksum offloads,
refactor bcm_sysport_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure that
features are correctly programmed during network device registration.
Since we can now be called during register_netdev() with clocks gated,
we need to temporarily turn them on/off in order to have a successful
register programming.
We also move the CRC forward setting read into
bcm_sysport_set_features() since priv->crc_fwd matters while turning on
RX checksum offload, that way we are guaranteed they are in sync in case
we ever add support for NETIF_F_RXFCS at some point in the future.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device gro_cells has been initialized, it should be freed,
otherwise it will be leaked
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When tcf_block_find() fails, it already rollbacks the qdisc refcnt,
so its caller doesn't need to clean up this again. Avoid calling
qdisc_put() again by resetting qdisc to NULL for callers.
Reported-by: syzbot+37b8770e6d5a8220a039@syzkaller.appspotmail.com
Fixes: e368fdb61d ("net: sched: use Qdisc rcu API instead of relying on rtnl lock")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1948367768 ("jump_label: Annotate entries that operate on
__init code earlier") refactored the code that manages runtime
patching of jump labels in modules that are tied to static keys
defined in other modules or in the core kernel.
In the latter case, we may iterate over the static_key_mod linked
list until we hit the entry for the core kernel, whose 'mod' field
will be NULL, and attempt to dereference it to get at its 'state'
member.
So let's add a non-NULL check: this forces the 'init' argument of
__jump_label_update() to false for static keys that are defined in
the core kernel, which is appropriate given that __init annotated
jump_label entries in the core kernel should no longer be active
at this point (i.e., when loading modules).
Fixes: 1948367768 ("jump_label: Annotate entries that operate on ...")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20181001081324.11553-1-ard.biesheuvel@linaro.org
Commit e872267b8b ("jump_table: move entries into ro_after_init
region") moved the __jump_table input section into the __ro_after_init
output section, but inadvertently put the macro in the wrong place in
the s390 linker script. Let's fix that.
Fixes: e872267b8b ("jump_table: move entries into ro_after_init region")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: linux-s390@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20180930164950.3841-1-ard.biesheuvel@linaro.org
Johannes Berg says:
====================
netlink: extended attribute validation
This adds further netlink attribute validation:
* min/max/range validation
* validation through a custom function pointer
This is useful to
* reduce boilerplate code in command handling code, if attributes
are used commonly across different commands
* get more extended ACK error messages/attribute pointers
* ensure attributes are valid even when ignored
(though this might be a problem when converting existing code)
Changes since v1:
* split off validate_type from type and use that for min/max/range
and function; this is better because the range is limited to the
range of s16 and so things like "u16 with minimum value 1" couldn't
be expressed earlier
* add macros for this, e.g. NLA_POLICY_MIN(NLA_U16, 1) for the case
mentioned in the previous bullet
Using this pretty much in all places where applicable in nl80211
reduces the code size there by about 1.8KiB, with just a minimal
code increase in lib/nlattr.o.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to have an arbitrary validation function attached
to a netlink policy that doesn't already use the validation_data
pointer in another way.
This can be useful to validate for example the content of a binary
attribute, like in nl80211 the "(information) elements", which must
be valid streams of "u8 type, u8 length, u8 value[length]".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without further bloating the policy structs, we can overload
the `validation_data' pointer with a struct of s16 min, max
and use those to validate ranges in NLA_{U,S}{8,16,32,64}
attributes.
It may sound strange to validate NLA_U32 with a s16 max, but
in many cases NLA_U32 is used for enums etc. since there's no
size benefit in using a smaller attribute width anyway, due
to netlink attribute alignment; in cases like that it's still
useful, particularly when the attribute really transports an
enum value.
Doing so lets us remove quite a bit of validation code, if we
can be sure that these attributes aren't used by userspace in
places where they're ignored today.
To achieve all this, split the 'type' field and introduce a
new 'validation_type' field which indicates what further
validation (beyond the validation prescribed by the type of
the attribute) is done. This currently allows for no further
validation (the default), as well as min, max and range checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta says:
====================
Support of Flow Director in HNS3 Ethernet Driver for HiP08 Rev2 SoC
This patch-set adds the support of FD(Flow Director) in the HNS3 PF driver
for HiP08 Rev2(0x21) SoC of Hisilicon. FD can be used in filtering the flows
and deciding to drop the flow or forward it to paricular queue.
Configuration consists of rules with input keys and actions. The rules are
stored in TCAM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds switch for flow director with ethtool command
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all flow director rules when unload hns3 driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, remove all entries in TCAM block, and keep flow
director rules list. After finishing reset, restore all entries.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for querying rule number and rule details
by ethtool commands.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for add and delete rule by ethtool commands.
HNS3 driver supports several flow types, include ETHER_FLOW,
IP_USER_FLOW, TCP_V4_FLOW, UDP_V4_FLOW, SCTP_V4_FLOW, IPV6_USER_FLOW,
TCP_V6_FLOW, UDP_V6_FLOW and SCTP_V6_FLOW.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each flow director rule consists of input key and action. The input key
is the condition for matching, includes tuples of L2/L3/L4 header.
Action is the behaviour when a packet matches with the input key, such
as drop the packet, or forward to a specified queue.
The input key is stored in the tcam blocks, Each bit of input key can
be masked.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow director is a new feature supported by hardware with revision 0x21.
This patch adds flow direcor initialization for each PF. It queries flow
director mode and tcam resource from firmware, selects tuples used for
input key.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull devfreq material for 4.20 from MyungJoo Ham.
"This mainly has follow-ups for recent Linux changes in a few
APIs (thermal, kfree, dev*, ...)."
* 'for-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mzx/devfreq:
PM / devfreq: remove redundant null pointer check before kfree
PM / devfreq: stopping the governor before device_unregister()
PM / devfreq: Convert to using %pOFn instead of device_node.name
PM / devfreq: Make update_devfreq() public
PM / devfreq: Don't adjust to user limits in governors
PM / devfreq: Fix handling of min/max_freq == 0
PM / devfreq: Drop custom MIN/MAX macros
PM / devfreq: Fix devfreq_add_device() when drivers are built as modules.
Andrew Lunn says:
====================
Continue towards using linkmode in phylib
These patches contain some further cleanup and helpers, and the first
real patch towards using linkmode bitmaps in phylink.
The macro magic in the RFC version has been replaced with run time
initialisation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.
Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.
Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro PHY_GBIT_FEAUTRES needs to change into a bitmap in order to
support link_modes. Remove its use from xgde by replacing it with its
definition.
Probably, the current behavior is wrong. It probably should be
ANDing not assigning.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers which take a linkmode rather than a u32 ethtool for
advertising settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>