Add the R8A77970 CMT module clocks.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock for UARTs 0 through 2 is UART012, the clock for UARTs 3 through
7 is UART34567.
For UART012, we stop the clock driver from changing the clock rate. This
is because the Synopsys UART driver simply sets the reference clock to 16x
the baud rate, but doesn't check if the actual rate is within the required
tolerance. The RZ/N1 clock divider can't provide this (we have to rely on
the UART's internal divider to set the correct clock rate), so you end up
with a clock rate that is way off what you wanted.
In addition, since the clock is shared between multiple UARTs, you don't
want the driver trying to change the clock rate as it may affect the other
UARTs (which may not have been configured yet, so you don't know what baud
rate they will use). Normally, the clock rate is set early on before Linux
to some very high rate that supports all of the clock rates you want.
This change stops the UART34567 clock rate from changing for the same
reasons.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since commit 222d7dbd25 ("net: prevent dst uses after free")
skb_dst_force() might clear the dst_entry attached to the skb.
The xfrm code don't expect this to happen, so we crash with
a NULL pointer dereference in this case. Fix it by checking
skb_dst(skb) for NULL after skb_dst_force() and drop the packet
in cast the dst_entry was cleared.
Fixes: 222d7dbd25 ("net: prevent dst uses after free")
Reported-by: Tobias Hommel <netdev-list@genoetigt.de>
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
sb_edac sometimes reports the wrong DIMM for a memory error found by
the patrol scrubber. That is because the hardware provides only a 4KB
page-aligned address for the error case.
This means that the EDAC driver will point at the DIMM matching offset
0x0 in the 4KB page, but because of interleaving across channels and
ranks, the actual DIMM involved may be different if the error is on some
other cache line within the page.
Therefore, reconstruct the socket/iMC/channel information from the "mce"
structure passed to the EDAC driver. The DIMM cannot be determined, so
pass "dimm=-1" to the EDAC core. It will report that all the DIMMs on
that channel may be affected.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180907230828.13901-3-tony.luck@intel.com
[ Improve comments on the functions to convert bank number
to memory controller number. Minor cleanup to commit message. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
[ Massage commit message more. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Users of the mce_register_decode_chain() are called for every logged
error. EDAC drivers should check:
1) Is this a memory error? [bit 7 in status register]
2) Is there a valid address? [bit 58 in status register]
3) Is the address a system address? [bitfield 8:6 in misc register]
The sb_edac driver performed test "1" twice. Waited far too long to
perform check "2". Didn't do check "3" at all.
Fix it by moving the test for valid address from
sbridge_mce_output_error() into sbridge_mce_check_error() and add a test
for the type immediately after. Delete the redundant check for the type
of the error from sbridge_mce_output_error().
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180907230828.13901-2-tony.luck@intel.com
[ Re-word commit message. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
This adds nodes for the Video Engine and the associated reserved memory
for the A33. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds nodes for the Video Engine and the associated reserved memory
for the A20. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds nodes for the Video Engine and the associated reserved memory
for sun5i-based platforms. Up to 96 MiB of memory are dedicated to the
CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
In commit ed194d1367 ("usb: core: remove local_irq_save() around
->complete() handler") I removed the only user of the flags variable and
forgot to remove the variable, leading to warning because it is unused
now.
Remove the unused variable.
Fixes: ed194d1367 ("usb: core: remove local_irq_save() around ->complete() handler")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 375899cddc.
The visibility of early messages did not longer take into account
"quiet", "debug", and "loglevel" early parameters.
It would be possible to invalidate and recompute LOG_NOCONS flag
for the affected messages. But it would be hairy.
Instead this patch just reverts the problematic commit. We could
come up with a better solution for the original problem. For example,
we could simplify the logic and just mark messages that should always
be visible or always invisible on the console.
Also this patch reverts the related build fix commit ffaa619af1
("printk: Fix warning about unused suppress_message_printing").
Finally, this patch does not put back the unused LOG_NOCONS flag.
Link: http://lkml.kernel.org/r/20180910145747.emvfzv4mzlk5dfqk@pathway.suse.cz
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Maninder Singh <maninder1.s@samsung.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
idma64_chan_irq() is invoked in hardirq handle function, it is unnecessary
to call spin_lock_irqsave.
Signed-off-by: Zhaoxiong Yuan <yuanzhx326@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/drm_plane.c: In function 'drm_mode_getplane_res':
drivers/gpu/drm/drm_plane.c:475:26: warning:
variable 'config' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1536646814-186429-1-git-send-email-yuehaibing@huawei.com
Add the devicetree nodes for the DMA core of the JZ4740 SoC, disabled
by default, as currently there are no clients for the DMA driver
(until the MMC driver and/or others get a devicetree node).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the two devicetree nodes for the two DMA cores of the JZ4770 SoC,
disabled by default, as currently there are no clients for the DMA
driver (until the MMC driver and/or others get a devicetree node).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver now accepts two memory resources, the first one for the
channel-specific registers, the second one for the controller-specific
registers.
Note that older devicetrees, without this commit, will still work with
the jz4780-dma driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is the standard method provided by dmaengine header.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Func jz4780_dma_desc_residue() expects the index to the next hw
descriptor as its last parameter. Caller func jz4780_dma_tx_status(),
however, applied modulus before passing it. When the current hw
descriptor was last in the list, the index passed became zero.
The resulting excess of reported residue especially caused problems
with cyclic DMA transfer clients, i.e. ALSA AIC audio output, which
rely on this for determining current DMA location within buffer.
Combined with the recent and related residue-reporting fixes, spurious
ALSA audio underruns on jz4770 hardware are now fixed.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Normally, we wouldn't set the channel transfer count register directly
when using descriptor-driven transfers. However, there is no harm in
doing so, and it allows jz4780_dma_desc_residue() to report the correct
residue of an ongoing transfer, no matter when it is called.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simple cleanup, no changes to actual logic here.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 'dtc' word in jz DMA descriptors contains two fields: The
lowest 24 bits are the transfer count, and upper 8 bits are the DOA
offset to next descriptor. The upper 8 bits are now correctly masked
off when computing residue in jz4780_dma_desc_residue(). Note that
reads of the DTCn hardware reg are automatically masked this way.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With the fast DMA bit set, the DMA will transfer twice as much data
per clock period to the AIC, so there is little point not to set it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4725B has one DMA core starring six DMA channels.
As for the JZ4770, each DMA channel's clock can be enabled with
a register write, the difference here being that once started, it
is not possible to turn it off.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4740 SoC has a single DMA core starring six DMA channels.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4770 SoC has two DMA cores, each one featuring six DMA channels.
The major change is that each channel's clock can be enabled or disabled
through register writes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If we make this driver depend on MACH_JZ4780, that means it can be
enabled only if we're building a kernel specially crafted for a
JZ4780-based board, while most GNU/Linux distributions will want one
generic MIPS kernel that works on multiple boards.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The only information we use in the 8-word version of the hardware DMA
descriptor that is not present in the 4-word version is the transfer
type, aka. the ID of the source or recipient device.
Since the transfer type will never change for a DMA channel in use,
we can just set it once for all in the corresponding DMA register
before starting any transfer.
This has several benefits:
* the driver will handle twice as many hardware DMA descriptors;
* the driver is closer to support the JZ4740, which only supports 4-word
hardware DMA descriptors;
* the JZ4770 SoC needs the transfer type to be set in the corresponding
DMA register anyway, even if 8-word descriptors are in use.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The register area of the JZ4780 DMA core can be split into different
sections for different purposes:
* one set of registers is used to perform actions at the DMA core level,
that will generally affect all channels;
* one set of registers per DMA channel, to perform actions at the DMA
channel level, that will only affect the channel in question.
The problem rises when trying to support new versions of the JZ47xx
Ingenic SoC. For instance, the JZ4770 has two DMA cores, each one
with six DMA channels, and the register sets are interleaved:
<DMA0 chan regs> <DMA1 chan regs> <DMA0 ctrl regs> <DMA1 ctrl regs>
By using one memory resource for the channel-specific registers and
one memory resource for the core-specific registers, we can support
the JZ4770, by initializing the driver once per DMA core with different
addresses.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As part of the work to support various other Ingenic JZ47xx SoC versions,
which don't feature the same number of DMA channels per core, we now
deduce the number of DMA channels available from the devicetree
compatible string.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver calls clk_get() with the clock name set to NULL, which means
that the driver could only work when probed from devicetree. From now
on, we explicitly require the driver to be probed from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver now expects the devicetree to supply a second memory
resource. This resource is mandatory on the newly supported SoCs.
For the JZ4780, new devicetree code must also provide it, although the
driver is still compatible with older devicetree binaries.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds support for ColdFire mcf5441x-family edma
module.
The ColdFire edma module is slightly different from fsl-edma,
so a new driver is added. But most of the code is common
between fsl-edma and mcf-edma so it has been collected into a
separate common module fsl-edma-common (patch 1/3).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch fixes macros to use BIT() and GENMASK(), removing
also some unneeded.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds configurable registers (using __iomem addresses)
to allow the use of fsl-edma-common code with slightly different
edma module versions, as Vybrid (v1) and ColdFire (v2) are.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a new fsl-edma-common module to allow new
mcf-edma module code to use most of the fsl-edma code.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merging v4.14.68 into v4.14-rt I tripped over a conflict in the
rtmutex.c code. There I found that we had:
#ifdef CONFIG_DEBUG_LOCK_ALLOC
[..]
#endif
#ifndef CONFIG_DEBUG_LOCK_ALLOC
[..]
#endif
Really this should be:
#ifdef CONFIG_DEBUG_LOCK_ALLOC
[..]
#else
[..]
#endif
This cleans up that logic.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Rosin <peda@axentia.se>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180910214638.55926030@vmware.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have build failures attributed to turning on COMPILE_TEST, so revert
commit 90082cd397: ("dmaengine: add COMPILE_TEST for the drivers")
while we fix these.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
since we use PSP to program IH regs now
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix SDMA hang in prt mode, clear XNACK_WATERMARK in reg SDMA0_UTCL1_WATERMK to avoid the issue
Affected ASICs: VEGA10 VEGA12 RV1 RV2
v2: add reg clear for SDMA1
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Tested-by: Yukun Li <yukun1.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoid unlocking a lock we never locked.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Generate xGMI iolink for upper level usage
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the iolink type defines according to the new thunk spec
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Thunk will generate the XGMI topology information when necessary with the hive_id
for each specified device
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Retrieve hive_id from amdgpu device
v2: compile fix
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KFD need to get hive id from amdgpu to build up the XGMI topology
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver will save an array of XGMI hive info, each hive will have a list of devices
that have the same hive ID.
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add dummy function for xgmi function interface with psp
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>