Add support for PHYLINK, things are reasonably straight forward since we
do not yet support SerDes interfaces, that leaves us with just
MLO_AN_PHY and MLO_AN_FIXED to deal with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the logic from b53_adjust_link() responsible for overriding a
given port's link, speed, duplex and pause settings and make two helper
functions to set the port's configuration and the port's link settings.
We will make use of both, as separate functions while adding PHYLINK
support next.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB driver to manage per-port interrupts. Since we cannot
sleep during b53_io_ops, schedule a workqueue whenever we get a port
specific interrupt. We will later make use of this to call back into
PHYLINK when there is e.g: a link state change.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches expose individual interrupt line(s) for port specific
event(s), allow configuring these interrupts at an appropriate time
during port_enable/disable callbacks where all port specific resources
are known to be set-up and ready for use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new qed firmware with fixes and support for new features.
Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix
RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.
ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.
Misc:
- Debug Tools changes.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raydium touchscreen triggers interrupt storm after system-wide suspend:
[ 179.085033] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/65535)
According to Raydium, Windows driver does not reset the device after system
resume.
The HID over I2C spec does specify a reset should be used at intialization, but
it doesn't specify if reset is required for system suspend.
Tested this patch on other i2c-hid touchpanels I have and those touchpanels do
work after S3 without doing reset. If any regression happens to other
touchpanel vendors, we can use quirk for Raydium devices.
There's still one device uses I2C_HID_QUIRK_RESEND_REPORT_DESCR so keep it
there.
Cc: Aaron Ma <aaron.ma@canonical.com>
Cc: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If parent_get class method is not supported by the OSDs, fall back to
the legacy class method and assume that the parent is in the default
(i.e. "") namespace. The "use the child's image namespace" workaround
is no longer needed because creating images within namespaces will
require parent_get aware OSDs.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
In preparation for the new parent_get and parent_overlap_get class
methods, factor out the fetching and decoding of parent data.
As a side effect, we now decode all four fields in the "no parent"
case.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
syzbot reported a use-after-free in ceph_destroy_options(), called from
ceph_mount(). The problem was that create_fs_client() consumed the opt
pointer on some errors, but not on all of them. Make sure it always
consumes both libceph and ceph options.
Reported-by: syzbot+8ab6f1042021b4eed062@syzkaller.appspotmail.com
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
This patch adds the device tree binding of the r8a77990 SoC.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a teardown callback fails, the CPU hotplug code brings the CPU back to
the previous state. The previous state becomes the new target state. The
rollback happens in undo_cpu_down() which increments the state
unconditionally even if the state is already the same as the target.
As a consequence the next CPU hotplug operation will start at the wrong
state. This is easily to observe when __cpu_disable() fails.
Prevent the unconditional undo by checking the state vs. target before
incrementing state and fix up the consequently wrong conditional in the
unplug code which handles the failure of the final CPU take down on the
control CPU side.
Fixes: 4dddfb5faa ("smp/hotplug: Rewrite AP state machine core")
Reported-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Cc: josh@joshtriplett.org
Cc: peterz@infradead.org
Cc: jiangshanlai@gmail.com
Cc: dzickus@redhat.com
Cc: brendan.jackman@arm.com
Cc: malat@debian.org
Cc: sramana@codeaurora.org
Cc: linux-arm-msm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1809051419580.1416@nanos.tec.linutronix.de
----
perf trace:
- Augment the payload of syscall entry/exit tracepoints with the contents
of pointer arguments, such as the "filename" argument to the "open"
syscall or the 'struct sockaddr *' argument to the 'connect' syscall.
This is done using a BPF program that gets compiled and attached to
various syscalls:sys_enter_NAME tracepoints, copying via a BPF map and
"bpf-output" perf event the raw_syscalls:sys_enter tracepoint payload +
the contents of pointer arguments using the "probe_read", "probe_read_str"
and "perf_event_output" BPF functions.
The 'perf trace' codebase now just processes these augmented tracepoints
using the existing beautifiers that now check if there is more in the
perf_sample->raw_data than what is expected for a normal syscall enter
tracepoint (the common preamble, syscall id, up to six parameters),
using that with hand crafted struct beautifiers.
This is just to show how to augment the existing tracepoints, work will
be done to use DWARF or BTF info to do the pretty-printing and to create
the collectors.
For now this is done using an example restricted C BPF program, but the
end goal is to have this all autogenerated and done transparently.
Its still useful to have this example as one can use it as an skeleton and
write more involved filters, see the etcsnoop.c BPF example, for instance.
E.g.:
# cd tools/perf/examples/bpf/
# perf trace -e augmented_syscalls.c ping -c 1 ::1
0.000 ( 0.008 ms): openat(dfd: CWD, filename: /etc/ld.so.cache, flags: CLOEXEC) = 3
0.020 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libcap.so.2, flags: CLOEXEC) = 3
0.051 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libidn.so.11, flags: CLOEXEC) = 3
0.076 ( 0.003 ms): openat(dfd: CWD, filename: /lib64/libcrypto.so.1.1, flags: CLOEXEC) = 3
0.106 ( 0.003 ms): openat(dfd: CWD, filename: /lib64/libresolv.so.2, flags: CLOEXEC) = 3
0.136 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libm.so.6, flags: CLOEXEC) = 3
0.194 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libc.so.6, flags: CLOEXEC) = 3
0.224 ( 0.003 ms): openat(dfd: CWD, filename: /lib64/libz.so.1, flags: CLOEXEC) = 3
0.252 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libdl.so.2, flags: CLOEXEC) = 3
0.275 ( 0.003 ms): openat(dfd: CWD, filename: /lib64/libpthread.so.0, flags: CLOEXEC) = 3
0.730 ( 0.007 ms): open(filename: /usr/lib/locale/locale-archive, flags: CLOEXEC) = 3
PING ::1(::1) 56 data bytes
0.834 ( 0.008 ms): connect(fd: 5, uservaddr: { .family: INET6, port: 1025, addr: ::1 }, addrlen: 28) = 0
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.032 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.032/0.032/0.032/0.000 ms
0.914 ( 0.036 ms): sendto(fd: 4<socket:[843044]>, buff: 0x55b5e52e9720, len: 64, addr: { .family: INET6, port: 58, addr: ::1 }, addr_len: 28) = 64
#
Use 'perf trace -e augmented_syscalls.c,close ping -c 1 ::1' to see the
'close' calls as well, as it is not one of the syscalls augmented in that .c
file.
(Arnaldo Carvalho de Melo)
- Alias 'umount' to 'umount2' (Benjamin Peterson)
perf stat: (Jiri Olsa)
- Make many builtin-stat.c functions generic, moving display functions
to a separate file, prep work for adding the ability to store/display
stat data in perf record/top.
perf annotate: (Kim Phillips)
- Handle arm64 move instructions
perf report: (Thomas Richter):
- Create auxiliary trace data files for s390
libtraceevent: (Tzvetomir Stoyanov (VMware)):
- Split trace-seq related APIs in a separate header file.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCW5BHbgAKCRCyPKLppCJ+
J6WGAQDoPezUDbL8azCcscZZaaT4W63oAyVizOdy4qUIw5D2BAD+P2bYTmW3EKeO
d3FXWqtpMRNR0CFhWPi57XpJiia0oA0=
=ICRn
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-4.20-20180905' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo:
perf trace:
- Augment the payload of syscall entry/exit tracepoints with the contents
of pointer arguments, such as the "filename" argument to the "open"
syscall or the 'struct sockaddr *' argument to the 'connect' syscall.
This is done using a BPF program that gets compiled and attached to
various syscalls:sys_enter_NAME tracepoints, copying via a BPF map and
"bpf-output" perf event the raw_syscalls:sys_enter tracepoint payload +
the contents of pointer arguments using the "probe_read", "probe_read_str"
and "perf_event_output" BPF functions.
The 'perf trace' codebase now just processes these augmented tracepoints
using the existing beautifiers that now check if there is more in the
perf_sample->raw_data than what is expected for a normal syscall enter
tracepoint (the common preamble, syscall id, up to six parameters),
using that with hand crafted struct beautifiers.
This is just to show how to augment the existing tracepoints, work will
be done to use DWARF or BTF info to do the pretty-printing and to create
the collectors.
For now this is done using an example restricted C BPF program, but the
end goal is to have this all autogenerated and done transparently.
Its still useful to have this example as one can use it as an skeleton and
write more involved filters, see the etcsnoop.c BPF example, for instance.
E.g.:
# cd tools/perf/examples/bpf/
# perf trace -e augmented_syscalls.c ping -c 1 ::1
0.000 ( 0.008 ms): openat(dfd: CWD, filename: /etc/ld.so.cache, flags: CLOEXEC) = 3
0.020 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libcap.so.2, flags: CLOEXEC) = 3
0.051 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libidn.so.11, flags: CLOEXEC) = 3
0.076 ( 0.003 ms): openat(dfd: CWD, filename: /lib64/libcrypto.so.1.1, flags: CLOEXEC) = 3
0.106 ( 0.003 ms): openat(dfd: CWD, filename: /lib64/libresolv.so.2, flags: CLOEXEC) = 3
0.136 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libm.so.6, flags: CLOEXEC) = 3
0.194 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libc.so.6, flags: CLOEXEC) = 3
0.224 ( 0.003 ms): openat(dfd: CWD, filename: /lib64/libz.so.1, flags: CLOEXEC) = 3
0.252 ( 0.004 ms): openat(dfd: CWD, filename: /lib64/libdl.so.2, flags: CLOEXEC) = 3
0.275 ( 0.003 ms): openat(dfd: CWD, filename: /lib64/libpthread.so.0, flags: CLOEXEC) = 3
0.730 ( 0.007 ms): open(filename: /usr/lib/locale/locale-archive, flags: CLOEXEC) = 3
PING ::1(::1) 56 data bytes
0.834 ( 0.008 ms): connect(fd: 5, uservaddr: { .family: INET6, port: 1025, addr: ::1 }, addrlen: 28) = 0
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.032 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.032/0.032/0.032/0.000 ms
0.914 ( 0.036 ms): sendto(fd: 4<socket:[843044]>, buff: 0x55b5e52e9720, len: 64, addr: { .family: INET6, port: 58, addr: ::1 }, addr_len: 28) = 64
#
Use 'perf trace -e augmented_syscalls.c,close ping -c 1 ::1' to see the
'close' calls as well, as it is not one of the syscalls augmented in that .c
file.
(Arnaldo Carvalho de Melo)
- Alias 'umount' to 'umount2' (Benjamin Peterson)
perf stat: (Jiri Olsa)
- Make many builtin-stat.c functions generic, moving display functions
to a separate file, prep work for adding the ability to store/display
stat data in perf record/top.
perf annotate: (Kim Phillips)
- Handle arm64 move instructions
perf report: (Thomas Richter):
- Create auxiliary trace data files for s390
libtraceevent: (Tzvetomir Stoyanov (VMware)):
- Split trace-seq related APIs in a separate header file.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The PARAVIRT_XXL changes introduced a redefinition of SAVE_FLAGS under
certain configurations. Cure it
Fixes: 6da63eb241 ("x86/paravirt: Move the pv_irq_ops under the PARAVIRT_XXL umbrella").
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20180905053720.13710-1-jgross@suse.com
The function batadv_tvlv_handler_register is responsible for adding new
tvlv_handler to the handler_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: ef26157747 ("batman-adv: tvlv - basic infrastructure")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_tt_global_orig_entry_add is responsible for adding new
tt_orig_list_entry to the orig_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: d657e621a0 ("batman-adv: add reference counting for type batadv_tt_orig_list_entry")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_softif_vlan_get is responsible for adding new
softif_vlan to the softif_vlan_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: 5d2c05b213 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When the kernel.print-fatal-signals sysctl has been enabled, a simple
userspace crash will cause the kernel to write a crash dump that contains,
among other things, the kernel gsbase into dmesg.
As suggested by Andy, limit output to pt_regs, FS_BASE and KERNEL_GS_BASE
in this case.
This also moves the bitness-specific logic from show_regs() into
process_{32,64}.c.
Fixes: 45807a1df9 ("vdso: print fatal signals")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180831194151.123586-1-jannh@google.com
Loops per jiffy is calculated by multiplying tsc_khz with 1e3 and then
dividing it by HZ.
Both tsc_khz and the temporary variable holding the multiplication result
are of type unsigned long, so on 32bit the result is truncated to the lower
32bit.
Use u64 as type for the temporary variable and cast tsc_khz to it before
multiplying.
[ tglx: Massaged changelog and removed pointless braces ]
Fixes: cf7a63ef4e ("x86/tsc: Calibrate tsc only once")
Signed-off-by: Chuanhua Lei <chuanhua.lei@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: yixin.zhu@linux.intel.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Tatashin <pasha.tatashin@microsoft.com>
Cc: Rajvi Jingar <rajvi.jingar@intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Link: https://lkml.kernel.org/r/1536228203-18701-1-git-send-email-chuanhua.lei@linux.intel.com
The function batadv_nc_get_nc_node is responsible for adding new nc_nodes
to the in_coding_list and out_coding_list. It first checks whether the
entry already is in the list or not. If it is, then the creation of a new
entry is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: d56b1705e2 ("batman-adv: network coding - detect coding nodes and remove these after timeout")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_gw_node_add is responsible for adding new gw_node to
the gateway_list. It is expecting that the caller already checked that
there is not already an entry with the same key or not.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The per hardif sysfs file "batman_adv/elp_interval" is using the generic
functions to store/show uint values. The helper __batadv_store_uint_attr
requires the softif net_device as parameter to print the resulting change
as info text when the users writes to this file. It uses the helper
function batadv_info to add it at the same time to the kernel ring buffer
and to the batman-adv debug log (when CONFIG_BATMAN_ADV_DEBUG is enabled).
The function batadv_info requires as first parameter the batman-adv softif
net_device. This parameter is then used to find the private buffer which
contains the debug log for this batman-adv interface. But
batadv_store_throughput_override used as first argument the slave
net_device. This slave device doesn't have the batadv_priv private data
which is access by batadv_info.
Writing to this file with CONFIG_BATMAN_ADV_DEBUG enabled can either lead
to a segfault or to memory corruption.
Fixes: 0744ff8fa8 ("batman-adv: Add hard_iface specific sysfs wrapper macros for UINT")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The per hardif sysfs file "batman_adv/throughput_override" prints the
resulting change as info text when the users writes to this file. It uses
the helper function batadv_info to add it at the same time to the kernel
ring buffer and to the batman-adv debug log (when CONFIG_BATMAN_ADV_DEBUG
is enabled).
The function batadv_info requires as first parameter the batman-adv softif
net_device. This parameter is then used to find the private buffer which
contains the debug log for this batman-adv interface. But
batadv_store_throughput_override used as first argument the slave
net_device. This slave device doesn't have the batadv_priv private data
which is access by batadv_info.
Writing to this file with CONFIG_BATMAN_ADV_DEBUG enabled can either lead
to a segfault or to memory corruption.
Fixes: 0b5ecc6811 ("batman-adv: add throughput override attribute to hard_ifaces")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The probe ELPs for WiFi interfaces are expanded to contain at least
BATADV_ELP_MIN_PROBE_SIZE bytes. This is usually a lot more than the
number of bytes which the template ELP packet requires.
These extra padding bytes were not initialized and thus could contain data
which were previously stored at the same location. It is therefore required
to set it to some predefined or random values to avoid leaking private
information from the system transmitting these kind of packets.
Fixes: e4623c913508 ("batman-adv: Avoid probe ELP information leak")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The spi-dw driver currently only supports 8 or 16 bits per word.
Since the hardware supports 4-16 bits per word, adapt the driver
to also support this.
Tested on socfpga cyclone5 with a 9-bit SPI display.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case where lo_vag <= SGTL5000_LINE_OUT_GND_BASE, lo_vag
is set to zero and later vol_quot is computed by dividing by
lo_vag causing a division by zero error. Fix this by avoiding
a zero division and set vol_quot to zero in this specific case
so that the lowest setting for i is correctly set.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-gpio.c: In function 'spi_gpio_remove':
drivers/spi/spi-gpio.c:450:33: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 12864ff854 (ACPI / LPSS: Avoid PM quirks on suspend and resume
from hibernation) bypasses lpss quirks for S3 and S4, by setting a flag
for S3/S4 in acpi_lpss_suspend(), and check that flag in
acpi_lpss_resume().
But this overlooks the boot case where acpi_lpss_resume() may get called
without a corresponding acpi_lpss_suspend() having been called.
Thus force setting the flag during boot.
Fixes: 12864ff854 (ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200989
Reported-and-tested-by: William Lieurance <william.lieurance@namikoda.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+: 12864ff854 (ACPI / LPSS: Avoid ...)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Calling dmi_check_system() early only works on X86. Other
architectures initialize the DMI subsystem later so it's not
ready yet when ACPI itself gets initialized.
In the best case it results in a useless call to a function which
will do nothing. But depending on the dmi implementation, it could
also result in warnings. Best is to not call the function when it
can't work and isn't needed.
Additionally, if anyone ever needs to add non-x86 quirks, it would
surprisingly not work, so document the limitation to avoid confusion.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: cce4f632db (ACPI: fix early DSDT dmi check warnings on ia64)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
rsnd driver sometimes want to know which address is used when debugging.
But it will indicate "(____ptrval____)" if it used "%p" on dev_dbg().
Let's use "%pa" or "%px" for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver will fallback to PIO mode if it can't get DMA
handler. But, DMA might return -EPROBE_DEFER when probe timing.
This driver always fallback to PIO mode especially from
commit ac6bbf0cdf ("iommu: Remove IOMMU_OF_DECLARE") because
of this reason.
The DMA driver will be probed later, but sound driver might be
probed as PIO mode in such case. This patch fixup this issue.
Then, -EPROBE_DEFER is not error. Thus, let's don't indicate error
message in such case.
And it needs to call rsnd_adg_remove() individually if probe failed,
because it registers clk which should be unregister.
Maybe PIO fallback feature itself is not needed,
but let's keep it so far.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG has buffer over flow bug if DT has more than 3 clock-frequency.
This patch fixup this issue, and uses first 2 values.
clock-frequency = <x y>; /* this is OK */
clock-frequency = <x y z>; /* this is NG */
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 8c9d750333 ("ASoC: rsnd: ssiu: Support BUSIF
other than BUSIF0") added new SSIU registers.
But it is using white-space for it.
This patch fixup it to use tab.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The !port check is redundant as it being performed in the following
check. Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the hardcoded clock indices by R9A06G032_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Renesas R-Car gen3 SoCs have both CMT and TMU timers, so we have to enable
building them in Kconfig.platforms (as they don't normally have the prompts
in Kconfig).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
-----BEGIN PGP SIGNATURE-----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=bEhk
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.19-rc2
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
we can place a fence to a timeline point after expanded.
v2: change func parameter order
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/246543/
we can fetch timeline point fence after expanded.
v2: The parameter fence is the result of the function and should come last.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/246541/
moved to front of file.
stub fence will be used by timeline syncobj as well.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/246539/
That is certainly totally nonsense. dma_fence_enable_sw_signaling()
is the function who is calling this callback.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/246535/
Since this is handling user provided bpp and depth, we need to sanity
check and propagate the EINVAL back rather than assume what the insane
client intended and fill the logs with DRM_ERROR.
v2: Check both bpp and depth match the builtin pixel format, and
introduce a canonical DRM_FORMAT_INVALID to reserve 0 against any future
fourcc.
v3: Mark up DRM_FORMAT_C8 as being {bpp:8, depth:8}
Testcase: igt/kms_addfb_basic/legacy-format
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905153116.28924-1-chris@chris-wilson.co.uk
Userspace on big endian machhines typically expects the ADDFB ioctl
returns a big endian framebuffer. drm_mode_addfb() will call
drm_mode_addfb2() unconditionally with little endian DRM_FORMAT_*
values though, which is wrong. This patch fixes that.
Drivers (both kernel and xorg) have quirks in place to deal with the
broken drm_mode_addfb() behavior. Because of this we can't just change
drm_mode_addfb() behavior for everybody without breaking things. Add
the quirk_addfb_prefer_host_byte_order field to mode_config, so drivers
can opt-in.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180905060445.15008-5-kraxel@redhat.com
framebuffer_check() expects that drm_get_format_info() will not fail if
the __drm_format_info() call was successful. That'll work only in case
both are called with the same pixel_format value, so masking out the
DRM_FORMAT_BIG_ENDIAN flag isn't a good idea.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20180905060445.15008-4-kraxel@redhat.com