Suspend/resume were not working correctly with pm runtime.
Now suspend check if the chip is already suspended, and
resume put runtime pm in the correct state.
Issues seen prior to this were:
When entering suspend, there was an error in logs because we
were disabling vddio regulator although it was already disabled.
And when resuming, the chip was pull back to full power but the
pm_runtime state was not updated. So it was believing it was
still suspended.
Fixes: 4599cac846 ("iio: imu: inv_mpu6050: use runtime pm with autosuspend")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d24517267 ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently there is an off-by-one check on the number of channels that
will cause an arry overrun in array st->output_mode when calling the
function d5770r_store_output_range. Fix this by using >= rather than >
to check for maximum number of channels.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: cbbb819837 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
flush hw FIFO before device reset in order to avoid possible races
on interrupt line 1. If the first interrupt line is asserted during
hw reset the device will work in I3C-only mode (if it is supported)
Fixes: 801a6e0af0 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Fixes: 43901008fd ("iio: imu: st_lsm6dsx: add support to LSM6DSR")
Reported-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Vitor Soares <vitor.soares@synopsys.com>
Tested-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the call to iio_str_to_fixpoint when using 'dB' sufix.
Before this the scale_db was not used when parsing the string written to
the attribute and it failed with invalid value.
Fixes: b852822474 ("iio: core: Handle 'dB' suffix in core")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix id relative path that shouldn't contain 'bindings', as pointed out
when submitting st,stm32-dac bindings conversion to json-schema [1].
[1] https://patchwork.ozlabs.org/patch/1257568/
Fixes: a8cf1723c4 ("dt-bindings: iio: adc: stm32-adc: convert bindings to json-schema")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's not uncommon that voltage regulator becomes available later during
kernel's boot process. This patch adds info message about unavailable
regulators in a case of the deferred-probe error and also amends the
error message with a error code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The vcnl4000 IIO driver introduced a new attribute
"in_proximity_nearlevel". This adds it to the list of documented ABI
for sysfs-bus-iio.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an object can be considered close to the sensor is hardware
dependent. Allowing to configure the property via device tree
allows to configure this device specific value.
This is useful for e.g. iio-sensor-proxy to indicate to userspace
if an object is close to the sensor.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This value indicates when userspace should consider an object
near to the sensor/device.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce a file for common properties of iio sensors. So far this
contains the new proximity-near-level property for proximity sensors
that indicates when an object should be considered near.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the vcnl4000 device tree bindings to the new YAML format.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to https://www.analog.com/, the company name is spelled
"Analog Devices".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
This change reworks the predisable/postenable hooks so that the pollfunc is
attached/detached in the correct position.
It also balances the calls a bit, by grouping the preenable and the
iio_triggered_buffer_postenable() into a single
isl29125_buffer_postenable() function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together. Reduces boilerplate and suggested
by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This only occurs once in the driver and isn't needed in this case either,
so drop it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Given the parameter is void *, casting to u8 * is unnecessary.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
A mixture of:
* Casts to u8 * for the val parameter which is void * and so needs no cast.
* Explicit sizes when we can use sizeof on the destination / source variable.
Not broken in anyway, I'm just trying to tidy up the is in the subsystem to
avoid it getting cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
A mixture of:
* Unnecessary casts of val parameter to u8 * which makes little sense as
the function take a void *.
* Explicit sizes where we can use the destination type to define that.
Note that's not true in all cases as we do read 3 bytes into 4 byte
destinations.
Note that noting was broken here, I'm just trying to ensure this doesn't
get cut and paste into more drivers so cleaning these out subsystem wide.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
st_lsm6dsx is a standalone driver for STM IMU sensors and does not rely
on st_sensor common framework, so it does not include st_sensor common
definitions.
In st_lsm6dsx_shub driver st_sensors.h is used just to introduce the
default wai address for LIS3MDL sensor.
Drop this largely unconnected include file and introduce the default wai
address for LIS3MDL in st_lsm6dsx_ext_dev_settings register map
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
This is the last user of 'devm_iio_device_match()', so it can be removed as
well in this patch.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Moves this to be the first check, as it's very simple and fails the
registration earlier, instead of potentially initializing the
'indio_dev->label' and checking for duplicate indexes, and then failing
with this simple-check.
This is a minor optimization, since '__iio_device_register()' will waste
fewer validation cycles in case 'indio_dev->info' is NULL.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This field doesn't seem used. It seems that only 'buffer->attrs' was ever
used to extend sysfs attributes for an IIO buffer.
Moving forward, it may not make sense to keep it. This patch removes the
field and it's initialization code.
Since we want to rework IIO buffer, to be able to add more buffers per IIO
device, we will merge [somehow] the 'buffer' & 'scan_elements' groups, and
we will continue to add the attributes to the 'buffer' group.
Removing it here, will also make the rework here a bit smaller, since
this code will not be present.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 1fd4567026 ("iio: imu: adis: add support product ID check in adis_initial_startup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix a typo. 'at the a time' -> 'at a time'.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The description below is already in use for px30.dtsi,
but was somehow never added to a document, so add
"rockchip,px30-saradc", "rockchip,rk3399-saradc"
for saradc nodes on a px30 platform to rockchip-saradc.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The description below is already in use for rk3308.dtsi,
but was somehow never added to a document, so add
"rockchip,rk3308-saradc", "rockchip,rk3399-saradc"
for saradc nodes on a rk3308 platform to rockchip-saradc.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Current dts files with 'saradc' nodes are manually verified.
In order to automate this process rockchip-saradc.txt
has to be converted to yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO DMA buffer is a DMA buffer implementation. As such it should
include buffer_impl.h rather than buffer.h.
The include to buffer.h in buffer-dma.h should be buffer_impl.h so it has
access to the struct iio_buffer definition. The code currently only works
because all places that use buffer-dma.h include buffer_impl.h before it.
The include to buffer.h in industrialio-buffer-dma.c can be removed since
those file does not reference any of buffer consumer functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add driver for the Maxim MAX1241 12-bit, single-channel ADC.
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX1240-MAX1241.pdf
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Lazar <alazar@startmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device-tree bindings documentation for the MAX1241 device driver.
Signed-off-by: Alexandru Lazar <alazar@startmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for STMicroelectronics LISHH12 accelerometer in st_accel
framework.
https://www.st.com/resource/en/datasheet/lis2hh12.pdf
Signed-off-by: Gaëtan André <rvlander@gaetanandre.eu>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add LIS3MDL register map to sensor hub device table.
Tested with LSM6DSM.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
