All functions in arch/x86/xen/irq.c and arch/x86/xen/xen-asm*.S are
specific to PV guests. Include them in the kernel with CONFIG_XEN_PV only.
Make the PV specific code in arch/x86/entry/entry_*.S dependent on
CONFIG_XEN_PV instead of CONFIG_XEN.
The HVM specific code should depend on CONFIG_XEN_PVHVM.
While at it reformat the Makefile to make it more readable.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: xen-devel@lists.xenproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: akataria@vmware.com
Cc: rusty@rustcorp.com.au
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20180828074026.820-2-jgross@suse.com
When dapm_power_widgets() is called, the dapm_pre_sequence_async() and
dapm_post_sequence_async() functions are scheduled for all DAPM contexts
(apart from the card DAPM context) regardless of whether the DAPM
context is already in the desired state. The overhead of this is not
insignificant and the more DAPM contexts there are the more overhead
there is.
For example, on the Tegra124 Jetson TK1, when profiling the time taken
to execute the dapm_power_widgets() the following times were observed.
Times for function dapm_power_widgets() are (us):
Min 23, Ave 190, Max 434, Count 39
Here 'Count' is the number of times that dapm_power_widgets() has been
called. Please note that the above time were measured using ktime_get()
to log the time on entry and exit from dapm_power_widgets(). So it
should be noted that these times may not be purely the time take to
execute this function if it is preempted. However, after applying this
patch and measuring the time taken to execute dapm_power_widgets() again
a significant improvement is seen as shown below.
Times for function dapm_power_widgets() are (us):
Min 4, Ave 16, Max 82, Count 39
Therefore, optimise the dapm_power_widgets() function by only scheduling
the dapm_pre/post_sequence_async() work if the DAPM context is not in
the desired state.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch update binding with the new R40 compatible.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch add the r40 compatible to the ahci_sunxi's supported list of
compatible.
Since R40 need ahci_platform to handle the reset controller, we also add
the new AHCI_PLATFORM_GET_RESETS flag for ahci_platform_get_resources().
This has no consequence for older platform (a10, a20) since the reset is
optional.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch document the new optional phy-supply.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SoC R40 AHCI controller need a PHY regulator to work.
But since the PHY is embedded in the controller, we cannot do a DT node for it,
since phy-supply works only in node with a PHY compatible.
So this patch adds a way to add an optional phy-supply regulator on AHCI controller node.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch document the new optional ahci-supply.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SoC R40 AHCI controller need a regulator to work.
So this patch add a way to add an optional regulator on AHCI controller.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fix the indentation of target-supply's ':'.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make use of the recently added &pinctrl and &watchdog labels. This
makes the whole file consistent and knowledge of the ahb/apb structure
is hidden.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Make use of the recently added &pinctrl and &watchdog labels. This
makes the whole file consistent and knowledge of the ahb/apb structure
is hidden.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This change increases the source code readability.
Instead of using `spi->child[cs].direct_access.XXX` use `dir_acc->XXX`.
Instead of using `orion_spi->child[cs].direct_access.vaddr` use `vaddr`.
Signed-off-by: Kosta Zertsekel <zertsekel@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT binding documentation for this new ASoC driver.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the MikroElektronika PROTO audio codec board.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Main purpose of .nolock_start is we need to call
some function without spinlock.
OTOH we have .prepare which main purpose is
called under atomic context.
Then, it is called without spinlock.
In summary, our main callback init/quit, and start/stop
are called under "atomic context and with spinlock".
And some function need to be called under
"non-atomic context or without spinlock".
Let's merge .nolock_start and prepare to be more clear code.
Then, let's rename nolock_stop to cleanup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently ssiu's .init is only called once during audio stream.
But SSIU with different BUSIF, shall be initialized each time,
even they are used in the same audio stream.
This patch introduces ssiu_status for BUSIF0 to BUSIF7 in rsnd_ssiu,
to make sure same .init for different BUSIF can always be executed.
To avoid the first stopped stream to stop the whole SSIU,
which may still has other BUSIF instance running, use usrcnt to count
the usage of SSIU, only the last user of SSIU can stop the whole SSIU.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently only BUSIF0 is supported by SSIU, all register setting
is done only for BUSIF.
Since BUSIF1 ~ BUSIF7 has been supported, so also support
these BUSIF from SSIU.
One note is that we can't support SSI9-4/5/6/7 so far,
because its address is out of calculation rule.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PDMACHCR setting for SSI only considers BUSIF0 so far.
But BUSIF1 ~ BUSIF7 also maybe used, in the future.
This patch updates table gen2_id_table_ssiu, to also consider
BUSIF number used by SSI.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[kuninori: adjust to upstreaming]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA address calculated by rsnd_dma_addr() only considers BUSIF0 so far.
But BUSIF1 ~ BUSIF7 also maybe used, in the future.
This patch updates DMA address calculations, to also consider
BUSIF number used by SSI.
One note is that we can't support SSI9-4/5/6/7 so far,
because its address is out of calculation rule.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[kuninori: adjust to upstreaming]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The number of channel handled by SSI maybe differs from the one set
in hw_params, currently SSI checks hw_params's channel number,
and constrains to use same channel number, when it is being
used by multiple clients.
This patch corrects to check runtime channel number rather
than channel number set in hw_params.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[kuninori: adjust to upstreaming]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same SSI device may be used in different dai links,
by only having one dma struct in rsnd_ssi, after the first
instance's dma config be initilized, the following instances
can no longer configure dma, this causes issue, when their
dma data address are different from the first instance.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently rsnd_dai_stream *io is set to either &rdai->playback or
&rdai->capture based on whether it is a playback or capture stream,
in __rsnd_soc_hw_rule_* functions, but this is not necessary,
rsnd_dai_stream *io handler can be get from rule->private.
This patch removes 'is_play' parameter from hw_rule function.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for SNDRV_PCM_FMTBIT_S8 format.
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The slot width (system word length) was fixed at 32 bits.
This patch allows also setting it to 16 or 24 bits.
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add warning message to rsnd_kctrl_accept_runtime(), when kctrl
update is rejected due to corresponding dai-link is idle.
So that user can notice the reason of kctrl update failure.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[kuninori: adjust to upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clocking operations clk_get/set_rate, are non-atomic,
they shouldn't be called in soc_pcm_trigger() which is atomic.
Following issue was found due to execution of clk_get_rate() causes
sleep in soc_pcm_trigger(), which shouldn't be blocked.
We can reproduce this issue by following
> enable CONFIG_DEBUG_ATOMIC_SLEEP=y
> compile, and boot
> mount -t debugfs none /sys/kernel/debug
> while true; do cat /sys/kernel/debug/clk/clk_summary > /dev/null; done &
> while true; do aplay xxx; done
This patch adds support to .prepare callback, and moves non-atomic
clocking operations to it. As .prepare is non-atomic, it is always
called before trigger_start/trigger_stop.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
in_atomic(): 1, irqs_disabled(): 128, pid: 2242, name: aplay
INFO: lockdep is turned off.
irq event stamp: 5964
hardirqs last enabled at (5963): [<ffff200008e59e40>] mutex_lock_nested+0x6e8/0x6f0
hardirqs last disabled at (5964): [<ffff200008e623f0>] _raw_spin_lock_irqsave+0x24/0x68
softirqs last enabled at (5502): [<ffff200008081838>] __do_softirq+0x560/0x10c0
softirqs last disabled at (5495): [<ffff2000080c2e78>] irq_exit+0x160/0x25c
Preemption disabled at:[ 62.904063] [<ffff200008be4d48>] snd_pcm_stream_lock+0xb4/0xc0
CPU: 2 PID: 2242 Comm: aplay Tainted: G B C 4.9.54+ #186
Hardware name: Renesas Salvator-X board based on r8a7795 (DT)
Call trace:
[<ffff20000808fe48>] dump_backtrace+0x0/0x37c
[<ffff2000080901d8>] show_stack+0x14/0x1c
[<ffff2000086f4458>] dump_stack+0xfc/0x154
[<ffff2000081134a0>] ___might_sleep+0x57c/0x58c
[<ffff2000081136b8>] __might_sleep+0x208/0x21c
[<ffff200008e5980c>] mutex_lock_nested+0xb4/0x6f0
[<ffff2000087cac74>] clk_prepare_lock+0xb0/0x184
[<ffff2000087cb094>] clk_core_get_rate+0x14/0x54
[<ffff2000087cb0f4>] clk_get_rate+0x20/0x34
[<ffff20000113aa00>] rsnd_adg_ssi_clk_try_start+0x158/0x4f8 [snd_soc_rcar]
[<ffff20000113da00>] rsnd_ssi_init+0x668/0x7a0 [snd_soc_rcar]
[<ffff200001133ff4>] rsnd_soc_dai_trigger+0x4bc/0xcf8 [snd_soc_rcar]
[<ffff200008c1af24>] soc_pcm_trigger+0x2a4/0x2d4
Fixes: e7d850dd10 ("ASoC: rsnd: use mod base common method on SSI-parent")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
syzbot reported the uninitialized value exposure in certain situations
using virmidi loop. It's likely a very small race at writing and
reading, and the influence is almost negligible. But it's safer to
paper over this just by replacing the existing kvmalloc() with
kvzalloc().
Reported-by: syzbot+194dffdb8b22fc5d207a@syzkaller.appspotmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add another mark type flag FAN_MARK_FILESYSTEM for add/remove/flush
of super block mark type.
A super block watch gets all events on the filesystem, regardless of
the mount from which the mark was added, unless an ignore mask exists
on either the inode or the mount where the event was generated.
Only one of FAN_MARK_MOUNT and FAN_MARK_FILESYSTEM mark type flags
may be provided to fanotify_mark() or no mark type flag for inode mark.
Cc: <linux-api@vger.kernel.org>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Send events to group if super block mark mask matches the event
and unless the same group has an ignore mask on the vfsmount or
the inode on which the event occurred.
Soon, fanotify backend is going to support super block marks and
fanotify backend only supports path type events.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Add the infrastructure to attach a mark to a super_block struct
and detach all attached marks when super block is destroyed.
This is going to be used by fanotify backend to setup super block
marks.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Instead of calling the .set_timings() operation recursively from the
display device backwards, iterate over the devices manually in the DRM
encoder code. This moves the complexity to a single central location and
simplifies the logic in omap_dss_device drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The video timings are stored in the CRTC structure by the
omap_crtc_dss_set_timings() function, called by dss_mgr_set_timings()
from the .enable() operation of the internal encoders. This instead
belongs to the .set_timings() code paths. Move the
omap_crtc_dss_set_timings() calls accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The VENC encoder modifies the requested video mode to match the NTSC or
PAL timings (or reject the video mode completely) in the .set_timings()
operation. This should be performed in the .check_timings() operation
instead. Move the fixup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The SDI encoder modifies the pixel clock of the requested video mode to
take the limitations of the PLL into account in the .enable() operation.
This should be performed in the .check_timings() operation instead. Move
the fixup.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Constify many pointers to struct videomode, as well as pointers to
container structures, to ensure the video mode isn't modified after
the .check_timings() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI encoder modifies the passed videomode to take the requirements
of the internal DISPC-DSI bus into account in the .enable_video_output()
operation. This should be performed in the .check_timings() operation
instead. There is however no .check_timings() operation as the DSI
encoder uses a custom API, so move it to the closest match which is the
.set_config() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The video mode is aleady fixed up by the .check_timings() operation,
there's no need to repeat that when enabling the DPI output.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of call the dispc timings check function dispc_mgr_timings_ok()
from the internal encoders .check_timings() operation, expose it through
the dispc ops (after renaming it to check_timings) and call it directly
from omapdrm. This allows removal of now empty omap_dss_device
.check_timings() operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The encoder enable operation currently performs mode fixup and mode
setting for all omap_dss_device instances in the display pipeline. There
are dedicated encoder operations for those operations (respectively
.atomic_check() and .mode_set()), but they are not used for this
purpose.
Move the mode fixup code to .atomic_check() and the mode set code
.mode_set() to better fit the KMS model. The bus flags fixup has to
happen at .mode_set() time as there is no place to store the bus flags
in the atomic state structures. This could be solved by extending one of
the state structures, but as the goal is to replace the fixup by direct
usage of bus flags through the driver, that would be pointless.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The bus flags stored in omap_dss_device instances are used to fixup the
video mode before setting it, to honour constraints that can't be
expressed through drm_display_mode. The fixup occurs in the CRTC mode
set operation and the resulting video mode is stored internally in the
CRTC. It is then used next by omap_encoder_enable() to apply mode fixups
for the omap_dss_device instances in omap_encoder_update().
Move the hack to the omap_encoder_update() function right before
applying the omap_dss_device fixups, in order to group all fixups
together.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Panels drivers store their timings in a device data structure field that
is initialized at probe time, either from hardcoded values or from
firmware-supplied values. Those timings are then reported through the
.get_timings() operation to construct the panel display mode.
The panel timings are further modified by the .set_timings() operation,
which is called with the timings retrieved by .get_timings(), and
mangled by .check_timings(). The latter potentially adjusts the pixel
clock only.
Conceptually, modifying the panel timings is wrong, as the timings are
an intrinsic property of the panel and should thus be fixed.
Furthermore, modifying them this way at runtime can result in display
modes reported to userspace varying between calls, which is also wrong.
There's no actual need to store the mangled pixel clock value in the
timings. Don't modify the panel timings in the .set_timings() operation,
just forward it to the previous device in the display pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The analog TV, DVI and HDMI connectors all report timing information
through the .get_timings() information.
For analog TV outputs the information is queried from the encoder, so
the operation is unused. Remove it.
For HDMI outputs the display pipeline provides EDID capability, so the
operation is unused as well. Remove it.
For DVI outputs the operation is also unused if the pipeline provides
EDID capability. Otherwise (when the DDC bus is not connected) we
shouldn't hardcode a single mode, but instead report no mode and let the
KMS core add default modes. This is achieved by removing the operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Timings for the TV output are currently reported by the analog TV
connector. This has the disadvantage of having to handle timing-related
operations in a connector omap_dss_device that has, at the hardware
level, no knowledge of any timing information.
Implement the .get_timings() operation in the venc driver, and get
timings from the first component in the pipeline that implements the
operatation. This switches the duty of reporting analog TV timings from
the connector to the encoder.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The .check_timings() operation is called recursively from the display
device back to the output device. Most components just forward the
operation to the previous component in the chain, resulting in lots of
duplicated pass-through functions. To avoid that, iterate over the
components manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>