Commit graph

932,869 commits

Author SHA1 Message Date
Martin Willi
a9911937e7 ath10k: schedule hardware restart if WMI command times out
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.

Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.

The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.

Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-08-28 16:41:53 +03:00
Rakesh Pillai
58da3b4230 ath10k: skip resetting rx filter for WCN3990
WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.

Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1

Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-08-28 16:40:36 +03:00
Gao Xiang
f86cf25a60 Revert "staging: erofs: disable compiling temporarile"
This reverts commit 156c3df8d4.

Since XArray and the new mount apis aren't merged in 4.19-rc1
merge window, the BROKEN mark can be reverted directly without
any problems.

Fixes: 156c3df8d4 ("staging: erofs: disable compiling temporarile")
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-28 15:04:23 +02:00
Daniele Ceraolo Spurio
5382bed38f drm/i915/selftests: ring all doorbells in igt_guc_doorbells
We currently verify that all doorbells can be registered with GuC and
HW but don't check that all works as expected after a db ring.

Do a nop ring of all doorbells to make sure we haven't misprogrammed
any WQ or stage descriptor data. This will also help validating
upcoming changes in the db programming flow.

Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Acked-by: Katarzyna Dec <katarzyna.dec@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180827223614.22789-1-daniele.ceraolospurio@intel.com
2018-08-28 13:41:27 +01:00
Stefan Agner
b2dd9f2e5a HID: core: fix memory leak on probe
The dynamically allocted collection stack does not get freed in
all situations. Make sure to also free the collection stack when
using the parser in hid_open_report().

Fixes: 08a8a7cf14 ("HID: core: do not upper bound the collection stack")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2018-08-28 14:07:16 +02:00
Stefan Agner
e38c0ac55e HID: input: fix leaking custom input node name
Make sure to free the custom input node name on disconnect.

Cc: stable@vger.kernel.org # v4.18+
Fixes: c554bb0455 ("HID: input: append a suffix matching the application")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2018-08-28 14:06:34 +02:00
Takashi Iwai
87246f7fd5 ALSA: intel_hdmi: Use the new non-cached allocation
The HDMI LPE audio driver requires the non-cached page allocations for
its buffers.  With the recent support of SNDRV_DMA_TYPE_DEV_UC type,
we can reduce lots of codes in the driver side and let the memalloc
core doing it properly.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 13:56:49 +02:00
Takashi Iwai
4985ddbf1e ALSA: intel8x0: Use the new non-cached allocation for 440MX workaround
intel8x0 driver requires the non-cached pages for 440MX workaround,
and this can be implemented more easily with the new memalloc type,
SNDRV_DMA_TYPE_DEV_UC.  This allows us to reduce lots of code.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 13:56:48 +02:00
Takashi Iwai
193c7e1476 ALSA: hda: Remove substream allocation/free ops
Since we dropped the memory page fiddling in the own allocators in
hda_intel.c, the substream allocation and free ops in both hda_intel.c
and hda_tegra.c became nothing but the simple calls of the standard
snd_pcm_lib helpers.  As both are identical, there is no longer need
for indirect calls via ops; it's a good opportunity for removing ops
and simplifying the codes.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 13:56:47 +02:00
Takashi Iwai
fc47814369 ALSA: hda: Use new non-cached allocation for non-snoop mode
Now the ALSA memory allocator helper supports the new non-cached
pages, let's use the new type, SNDRV_DMA_TYPE_DEV_UC_SG, for HD-audio
driver.  This allows us to reduce lots of codes.

As another positive side-effect by this patch, the long-standing issue
with non-snoop mode playing in the non-mmap mode is fixed.  The core
memalloc helper does the proper pgprot setup for non-cached pages for
vmap(), which was missing in the past.

Reported-and-tested-by: Hans Hu <HansHu@zhaoxin.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 13:56:47 +02:00
Takashi Iwai
78c9be61c3 ALSA: hda: Check the non-cached stream buffers more explicitly
Introduce a new flag, uc_buffer, to indicate that the controller
requires the non-cached pages for stream buffers, either as a
chip-specific requirement or specified via snoop=0 option.
This improves the code-readability.

Also, this patch fixes the incorrect behavior for C-Media chip where
the stream buffers were never handled as non-cached due to the check
of driver_type even if you pass snoop=0 option.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 13:56:47 +02:00
Takashi Iwai
42e748a0b3 ALSA: memalloc: Add non-cached buffer type
In some cases (mainly for x86), we need the DMA coherent buffer with
non-cached pages.  Although this has been done in each driver side
like HD-audio and intel8x0, it can be done cleaner in the core memory
allocator.

This patch adds the new types, SNDRV_DMA_TYPE_DEV_UC and
SNDRV_DMA_TYPE_DEV_UC_SG, for allocating such non-cached buffer
pages.  On non-x86 architectures, they work as same as the standard
SNDRV_DMA_TYPE_DEV and *_SG.

One additional change by this move is that we can assure to pass the
non-cached pgprot to the vmapped buffer, too.  It eventually fixes the
case like non-snoop mode without mmap access on HD-audio.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 13:56:47 +02:00
Takashi Iwai
28f3f4f685 ALSA: memalloc: Simplify snd_malloc_dev_pages() calls
snd_malloc_dev_pages() and snd_free_dev_pages() are local functions
and the parameters passed there are all contained in snd_dma_buffer
object.  As a code-simplification, pass snd_dma_buffer object and
assign the address there like other allocators do (except for
snd_malloc_pages() which is called from outside, hence we can't change
easily).

Only code refactoring, no functional changes.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 13:56:46 +02:00
Takashi Iwai
03486830c5 ALSA: memalloc: Don't align the size to power-of-two
The size passed to dma_alloc_coherent() doesn't have to be aligned
with power-of-two, rather it should be the raw size.  As a minor
optimization, remove the size adjustment in the current code.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 13:56:46 +02:00
Sean O'Brien
ee34549243 HID: add support for Apple Magic Keyboards
USB device
	Vendor 05ac (Apple)
	Device 026c (Magic Keyboard with Numeric Keypad)

Bluetooth devices
	Vendor 004c (Apple)
	Device 0267 (Magic Keyboard)
	Device 026c (Magic Keyboard with Numeric Keypad)

Support already exists for the Magic Keyboard over USB connection.
Add support for the Magic Keyboard over Bluetooth connection, and for
the Magic Keyboard with Numeric Keypad over Bluetooth and USB
connection.

Signed-off-by: Sean O'Brien <seobrien@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2018-08-28 13:52:50 +02:00
AceLan Kao
fb6acf76c3 HID: i2c-hid: Fix flooded incomplete report after S3 on Rayd touchscreen
The incomplete report flooded after S3 and touchscreen becomes
malfunctioned.
[ 1367.646244] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/18785)
[ 1367.649471] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/28743)
[ 1367.651092] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/26757)
[ 1367.652658] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/52280)
[ 1367.654287] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/56059)

Adding device ID, 04F3:30CC, to the quirk to re-send report description
after resume.

Cc: stable@vger.kernel.org
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2018-08-28 13:46:12 +02:00
Song, Hongyan
71f6fa90a3 HID: increase maximum global item tag report size to 256
The maximum globale report size has changed from 32->...->96->128 in the past
years.  With the development usage of HID, the report_size max value 128 cannot
satisfy all requirements.

There are applications need to expose intrinsic metadata to camera stabilizing
applications such as 3DFE application. 3DFE intrinsic is designed to express
environmental information about sensor that may dynamically change while the
sensor is running (such data include noise spectral density, bias standard
deviation)

A sensor data field is SENSOR_VALUE_PAIR that consists of a PROPERTYKEY and
PROPVARIANT pair. It need to report a unique PROPERTYKEY for each data field.

Take “Noise Spectral Density” as an example, it report count will be
defined as below:

	"Size of Property key GUID(16 Byte) + property key index(4 Byte) +
	size of Noise Spectral Density value(4 Byte)"

In this case, the data report max is totally 192(24Byte), which is larger than
128, while max size 128 blocked it as illegal length. So increase the report
size to satisfy it and more demands in the future.

Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2018-08-28 13:43:53 +02:00
Andreas Bosch
e0ab8b26aa HID: intel-ish-hid: Enable Sunrise Point-H ish driver
Added PCI ID for Sunrise Point-H ISH.

Signed-off-by: Andreas Bosch <linux@progandy.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2018-08-28 13:40:55 +02:00
Takashi Iwai
b8e131542b ALSA: seq: Do error checks at creating system ports
snd_seq_system_client_init() doesn't check the errors returned from
its port creations.  Let's do it properly and handle the error paths.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 12:52:02 +02:00
Peter Rosin
c4f9712407 ARM: dts: at91: nattis: describe the lvds panel
Make the DT usable with the panel-lvds driver.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-08-28 12:14:41 +02:00
Peter Rosin
9cb6927680 ARM: dts: at91: nattis: move pinctrls for the lvds chip to the lvds node
The atmel hlcdc controller has nothing to do with these pins, so move
them to where they belong.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-08-28 12:14:41 +02:00
Peter Rosin
9a91c0c88a ARM: dts: at91: nattis: state the actual lvds-encoder chip
Just to be explicit.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-08-28 12:14:41 +02:00
Peter Rosin
f52eb20679 ARM: dts: at91: nattis: make the SD-card slot work
The cd-gpios signal is assumed active-low by the driver, and the
cd-inverted property is needed if it is, in fact, active-high. Fix
this oversight.

Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-08-28 12:14:41 +02:00
Peter Rosin
29feb2c960 ARM: dts: at91: nattis: set the PRLUD and HIPOW signals low
AT91_PINCTRL_OUTPUT_VAL(0) without AT91_PINCTRL_OUTPUT is a no-op, so
make sure the pins really output a zero.

Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-08-28 12:14:41 +02:00
Haim Dreyfuss
b88d26d97c nl80211: Pass center frequency in kHz instead of MHz
freq_reg_info expects to get the frequency in kHz. Instead we
accidently pass it in MHz.  Thus, currently the function always
return ERR rule. Fix that.

Fixes: 50f32718e1 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[fix kHz/MHz in commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:41:23 +02:00
Haim Dreyfuss
d3c89bbc74 nl80211: Fix nla_put_u8 to u16 for NL80211_WMMR_TXOP
TXOP (also known as Channel Occupancy Time) is u16 and should be
added using nla_put_u16 instead of u8, fix that.

Fixes: 50f32718e1 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:37:28 +02:00
Hoan Nguyen An
7a7dfc4770 pinctrl: sh-pfc: r8a77965: Add Audio SSI pin support
Add Audio SSI pin support for r8a77965.

Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-28 11:28:37 +02:00
Hoan Nguyen An
ada9a3d98f pinctrl: sh-pfc: r8a77965: Add Audio clock pin support
Add Audio clock pin support for r8a77965.

Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-28 11:28:37 +02:00
Biju Das
91d627a779 pinctrl: sh-pfc: r8a7796: Add R8A774A1 PFC support
Renesas RZ/G2M (r8a774a1) is pin compatible with R-Car M3-W (r8a7796),
however it doesn't have several automotive specific peripherals. Add
an r8a7796 specific pin groups/functions along with common pin
groups/functions for supporting both r8a7796 and r8a774a1 SoCs.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-28 11:28:37 +02:00
Biju Das
8f9a1acd8c dt-bindings: pinctrl: sh-pfc: Document r8a774a1 PFC support
Document PFC support for the R8A774A1 SoC.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-28 11:28:37 +02:00
Takeshi Kihara
951ae7cb06 pinctrl: sh-pfc: r8a77990: Add PWM pins, groups and functions
This patch adds PWM{0,1,2,3,4,5,6} pins, groups and functions to
the R8A77990 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-28 11:28:37 +02:00
Biju Das
491e9f585c pinctrl: sh-pfc: r8a77470: Add EtherAVB pin groups
Add EtherAVB groups and functions definitions for R8A77470 SoC.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-28 11:28:37 +02:00
Alexei Avshalom Lazar
9cf0a0b4b6 cfg80211: Add support for 60GHz band channels 5 and 6
The current support in the 60GHz band is for channels 1-4.
Add support for channels 5 and 6.
This requires enlarging ieee80211_channel.center_freq from u16 to u32.

Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:23:08 +02:00
Manikanta Pubbisetty
21a5d4c3a4 mac80211: add stop/start logic for software TXQs
Sometimes, it is required to stop the transmissions momentarily and
resume it later; stopping the txqs becomes very critical in scenarios where
the packet transmission has to be ceased completely. For example, during
the hardware restart, during off channel operations,
when initiating CSA(upon detecting a radar on the DFS channel), etc.

The TX queue stop/start logic in mac80211 works well in stopping the TX
when drivers make use of netdev queues, i.e, when Qdiscs in network layer
take care of traffic scheduling. Since the devices implementing
wake_tx_queue can run without Qdiscs, packets will be handed to mac80211
directly without queueing them in the netdev queues.

Also, mac80211 does not invoke any of the
netif_stop_*/netif_wake_* APIs if wake_tx_queue is implemented.
Since the queues are not stopped in this case, transmissions can continue
and this will impact negatively on the operation of the wireless device.

For example,
During hardware restart, we stop the netdev queues so that packets are
not sent to the driver. Since ath10k implements wake_tx_queue,
TX queues will not be stopped and packets might reach the hardware while
it is restarting; this can make hardware unresponsive and the only
possible option for recovery is to reboot the entire system.

There is another problem to this, it is observed that the packets
were sent on the DFS channel for a prolonged duration after radar
detection impacting the channel closing time.

We can still invoke netif stop/wake APIs when wake_tx_queue is implemented
but this could lead to packet drops in network layer; adding stop/start
logic for software TXQs in mac80211 instead makes more sense; the change
proposed adds the same in mac80211.

Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:16:35 +02:00
Rajeev Kumar Sirasanagandla
7417844b63 cfg80211: Avoid regulatory restore when COUNTRY_IE_IGNORE is set
When REGULATORY_COUNTRY_IE_IGNORE is set,  __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().

After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().

To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.

Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.

Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:15:51 +02:00
Dedy Lansky
30ca1aa536 cfg80211/mac80211: make ieee80211_send_layer2_update a public function
Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.

Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:15:27 +02:00
Richard Guy Briggs
f404c3ecc4 rfkill: fix spelling mistake contidion to condition
This came about while trying to determine if there would be any pattern
match on contid, a new audit container identifier internal variable.
This was the only one.

Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:15:27 +02:00
Jinbum Park
3a2af7cccb mac80211_hwsim: Fix possible Spectre-v1 for hwsim_world_regdom_custom
User controls @idx which to be used as index of hwsim_world_regdom_custom.
So, It can be exploited via Spectre-like attack. (speculative execution)

This kind of attack leaks address of hwsim_world_regdom_custom,
It leads an attacker to bypass security mechanism such as KASLR.

So sanitize @idx before using it to prevent attack.

I leveraged strategy [1] to find and exploit this gadget.

[1] https://github.com/jinb-park/linux-exploit/tree/master/exploit-remaining-spectre-gadget/

Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
[johannes: unwrap URL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:14:56 +02:00
Emmanuel Grumbach
20932750d9 mac80211: don't update the PM state of a peer upon a multicast frame
I changed the way mac80211 updates the PM state of the peer.
I forgot that we could also have multicast frames from the
peer and that those frame should of course not change the
PM state of the peer: A peer goes to power save when it
needs to scan, but it won't send the broadcast Probe Request
with the PM bit set.

This made us mark the peer as awake when it wasn't and then
Intel's firmware would fail to transmit because the peer is
asleep according to its database. The driver warned about
this and it looked like this:

 WARNING: CPU: 0 PID: 184 at /usr/src/linux-4.16.14/drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1369 iwl_mvm_rx_tx_cmd+0x53b/0x860
 CPU: 0 PID: 184 Comm: irq/124-iwlwifi Not tainted 4.16.14 #1
 RIP: 0010:iwl_mvm_rx_tx_cmd+0x53b/0x860
 Call Trace:
  iwl_pcie_rx_handle+0x220/0x880
  iwl_pcie_irq_handler+0x6c9/0xa20
  ? irq_forced_thread_fn+0x60/0x60
  ? irq_thread_dtor+0x90/0x90

The relevant code that spits the WARNING is:

        case TX_STATUS_FAIL_DEST_PS:
                /* the FW should have stopped the queue and not
                 * return this status
                 */
                WARN_ON(1);
                info->flags |= IEEE80211_TX_STAT_TX_FILTERED;

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199967.

Fixes: 9fef654433 ("mac80211: always update the PM state of a peer on MGMT / DATA frames")
Cc: <stable@vger.kernel.org>   #4.16+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:12:42 +02:00
Stanislaw Gruszka
38cb87ee47 cfg80211: make wmm_rule part of the reg_rule structure
Make wmm_rule be part of the reg_rule structure. This simplifies the
code a lot at the cost of having bigger memory usage. However in most
cases we have only few reg_rule's and when we do have many like in
iwlwifi we do not save memory as it allocates a separate wmm_rule for
each channel anyway.

This also fixes a bug reported in various places where somewhere the
pointers were corrupted and we ended up doing a null-dereference.

Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[rephrase commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:11:47 +02:00
Danek Duvall
d7c863a2f6 mac80211_hwsim: correct use of IEEE80211_VHT_CAP_RXSTBC_X
The mac80211_hwsim driver intends to say that it supports up to four
STBC receive streams, but instead it ends up saying something undefined.
The IEEE80211_VHT_CAP_RXSTBC_X macros aren't independent bits that can
be ORed together, but values.  In this case, _4 is the appropriate one
to use.

Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:09:05 +02:00
Danek Duvall
67d1ba8a6d mac80211: correct use of IEEE80211_VHT_CAP_RXSTBC_X
The mod mask for VHT capabilities intends to say that you can override
the number of STBC receive streams, and it does, but only by accident.
The IEEE80211_VHT_CAP_RXSTBC_X aren't bits to be set, but values (albeit
left-shifted).  ORing the bits together gets the right answer, but we
should use the _MASK macro here instead.

Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018-08-28 11:08:59 +02:00
Hoan Nguyen An
bc7133cef8 clk: renesas: r8a77965: Add FDP clock
This patch adds FDP1-0 clock to the R8A77965 SoC.

Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-08-28 11:06:11 +02:00
Dan Carpenter
c4f1957e14 ALSA: seq: add error check in snd_seq_system_client_init()
Static checkers complain that snd_seq_create_kernel_client() can return
-EBUSY here so we need to have some error handling.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-08-28 11:06:11 +02:00
John Fastabend
501ca81760 bpf: sockmap, decrement copied count correctly in redirect error case
Currently, when a redirect occurs in sockmap and an error occurs in
the redirect call we unwind the scatterlist once in the error path
of bpf_tcp_sendmsg_do_redirect() and then again in sendmsg(). Then
in the error path of sendmsg we decrement the copied count by the
send size.

However, its possible we partially sent data before the error was
generated. This can happen if do_tcp_sendpages() partially sends the
scatterlist before encountering a memory pressure error. If this
happens we need to decrement the copied value (the value tracking
how many bytes were actually sent to TCP stack) by the number of
remaining bytes _not_ the entire send size. Otherwise we risk
confusing userspace.

Also we don't need two calls to free the scatterlist one is
good enough. So remove the one in bpf_tcp_sendmsg_do_redirect() and
then properly reduce copied by the number of remaining bytes which
may in fact be the entire send size if no bytes were sent.

To do this use bool to indicate if free_start_sg() should do mem
accounting or not.

Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-08-28 09:01:06 +02:00
Chaitanya Kulkarni
04db0e5ec5 nvmet: free workqueue object if module init fails
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-08-28 08:40:44 +02:00
James Smart
afd299ca99 nvme-fcloop: Fix dropped LS's to removed target port
When a targetport is removed from the config, fcloop will avoid calling
the LS done() routine thinking the targetport is gone. This leaves the
initiator reset/reconnect hanging as it waits for a status on the
Create_Association LS for the reconnect.

Change the filter in the LS callback path. If tport null (set when
failed validation before "sending to remote port"), be sure to call
done. This was the main bug. But, continue the logic that only calls
done if tport was set but there is no remoteport (e.g. case where
remoteport has been removed, thus host doesn't expect a completion).

Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-08-28 08:40:43 +02:00
Michal Wnukowski
f1ed3df20d nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event
In many architectures loads may be reordered with older stores to
different locations.  In the nvme driver the following two operations
could be reordered:

 - Write shadow doorbell (dbbuf_db) into memory.
 - Read EventIdx (dbbuf_ei) from memory.

This can result in a potential race condition between driver and VM host
processing requests (if given virtual NVMe controller has a support for
shadow doorbell).  If that occurs, then the NVMe controller may decide to
wait for MMIO doorbell from guest operating system, and guest driver may
decide not to issue MMIO doorbell on any of subsequent commands.

This issue is purely timing-dependent one, so there is no easy way to
reproduce it. Currently the easiest known approach is to run "Oracle IO
Numbers" (orion) that is shipped with Oracle DB:

orion -run advanced -num_large 0 -size_small 8 -type rand -simulate \
	concat -write 40 -duration 120 -matrix row -testname nvme_test

Where nvme_test is a .lun file that contains a list of NVMe block
devices to run test against. Limiting number of vCPUs assigned to given
VM instance seems to increase chances for this bug to occur. On test
environment with VM that got 4 NVMe drives and 1 vCPU assigned the
virtual NVMe controller hang could be observed within 10-20 minutes.
That correspond to about 400-500k IO operations processed (or about
100GB of IO read/writes).

Orion tool was used as a validation and set to run in a loop for 36
hours (equivalent of pushing 550M IO operations). No issues were
observed. That suggest that the patch fixes the issue.

Fixes: f9f38e3338 ("nvme: improve performance for virtual NVMe devices")
Signed-off-by: Michal Wnukowski <wnukowski@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: updated changelog and comment a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-08-28 08:40:42 +02:00
Rob Herring
5ab64902b5 dmaengine: Convert to using %pOFn instead of device_node.name
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2018-08-28 10:45:40 +05:30
Stefan Agner
3f6e138d41 bpf: fix build error with clang
Building the newly introduced BPF_PROG_TYPE_SK_REUSEPORT leads to
a compile time error when building with clang:
net/core/filter.o: In function `sk_reuseport_convert_ctx_access':
  ../net/core/filter.c:7284: undefined reference to `__compiletime_assert_7284'

It seems that clang has issues resolving hweight_long at compile
time. Since SK_FL_PROTO_MASK is a constant, we can use the interface
for known constant arguments which works fine with clang.

Fixes: 2dbb9b9e6d ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2018-08-27 20:37:05 -07:00