This adds the rpmh-clk node to sdm845 based on the examples in the
bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the rpmh-rsc node to sdm845 based on the examples in the
bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The debug UART is very useful to have. I2C10 is enabled as an example
of a I2C port we can talk on for now. Eventually we'll want to put
peripherals under it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds nodes to SDM845-dtsi for all the I2C ports, all the SPI
ports, and UART9. Note that I2C / SPI / UART are a bit strange on
sdm845 because each "serial engine" has 4 pins associated with it and
depending on which firmware has been loaded into the serial engine
(loaded by the BIOS) the serial engine can behave like an I2C port, a
SPI port, or a UART. As per the landed bindings that means that we
need to create one node for each possible mode that the port could be
in. With 16 serial engines that means 16 x 3 = 48 nodes.
We get away with only creating 33 nodes for now because it seems very
likely that SDM845-based boards will actually all use the same UART
(UART 9) for debug purposes. While another UART could be used for
something like Bluetooth communication we can cross that path when we
come to it. Some documentation that I saw implied that using a UART
for "high speed" communications actually needs yet another different
serial engine firmware anyway.
Note that quick measurements adding all these nodes adds <10k of extra
space per dtb that they're included with. If this becomes a problem
we may need to think of a different way to structure this so that
boards only get the nodes they need (or figure out how to get dtc to
strip 'disabled' nodes). For now it seems OK.
These nodes were programmatically generated with a fairly dumb python
script. See http://crosreview.com/1091631 for the source.
NOTE: at the moment SPI chip select doesn't appear to work in my tests
with the latest posted SPI driver. All testing of SPI with this patch
has been done by hacking SPI to GPIO chip select.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add basic support for the pm8005 and pm8998 PMICs. For now just support
the GPIO controllers.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This is the bottom and by pushing this down it simplifies the callers
and otherwise leaves things as is. This is in preparation for allowing
fork to implement better handling of signals set to groups of processes.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This information is already available in the callers and by pushing it
down it makes the code a little clearer, and allows implementing
better handling of signales set to a group of processes in fork.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This information is already available in the callers and by pushing it
down it makes the code a little clearer, and allows better group
signal behavior in fork.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This passes the information we already have at the call sight into
do_send_sig_info. Ultimately allowing for better handling of signals
sent to a group of processes during fork.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This passes the information we already have at the call sight
into group_send_sig_info. Ultimatelly allowing for to better handle
signals sent to a group of processes.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Jon Maxwell says:
====================
tcp: improve setsockopt() TCP_USER_TIMEOUT accuracy
The patch was becoming bigger based on feedback therefore I have
implemented a series of 3 commits instead in V4.
This series is a continuation based on V3 here and associated feedback:
https://patchwork.kernel.org/patch/10516195/
Suggestions by Neal Cardwell:
1) Fix up units mismatch regarding msec/jiffies.
2) Address possiblility of time_remaining being negative.
3) Add a helper routine tcp_clamp_rto_to_user_timeout() to do the rto
calculation.
4) Move start_ts logic into helper routine tcp_retrans_stamp() to
validate tcp_sk(sk)->retrans_stamp.
5) Some u32 declation and return refactoring.
6) Return 0 instead of false in tcp_retransmit_stamp(), it's not a bool.
Suggestions by David Laight:
1) Don't cache rto in tcp_clamp_rto_to_user_timeout().
Suggestions by Eric Dumazet:
1) Make u32 declartions consistent.
2) Use patch series for easier review.
3) Convert icsk->icsk_user_timeout to millisconds to avoid jiffie to
msec dance.
4) Use seperate titles for each commit in the series.
5) Fix fuzzy indentation and line wrap issues.
6) Make commit titles descriptive.
Changes:
1) Call tcp_clamp_rto_to_user_timeout(sk) as an argument to
inet_csk_reset_xmit_timer() to save on rto declaration.
Every time the TCP retransmission timer fires. It checks to see if
there is a timeout before scheduling the next retransmit timer. The
retransmit interval between each retransmission increases
exponentially. The issue is that in order for the timeout to occur the
retransmit timer needs to fire again. If the user timeout check happens
after the 9th retransmit for example. It needs to wait for the 10th
retransmit timer to fire in order to evaluate whether a timeout has
occurred or not. If the interval is large enough then the timeout will
be inaccurate.
For example with a TCP_USER_TIMEOUT of 10 seconds without patch:
1st retransmit:
22:25:18.973488 IP host1.49310 > host2.search-agent: Flags [.]
Last retransmit:
22:25:26.205499 IP host1.49310 > host2.search-agent: Flags [.]
Timeout:
send: Connection timed out
Sun Jul 1 22:25:34 EDT 2018
We can see that last retransmit took ~7 seconds. Which pushed the total
timeout to ~15 seconds instead of the expected 10 seconds. This gets
more inaccurate the larger the TCP_USER_TIMEOUT value. As the interval
increases.
Add tcp_clamp_rto_to_user_timeout() to determine if the user rto has
expired. Or whether the rto interval needs to be recalculated. Use the
original interval if user rto is not set.
Test results with the patch is the expected 10 second timeout:
1st retransmit:
01:37:59.022555 IP host1.49310 > host2.search-agent: Flags [.]
Last retransmit:
01:38:06.486558 IP host1.49310 > host2.search-agent: Flags [.]
Timeout:
send: Connection timed out
Mon Jul 2 01:38:09 EDT 2018
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Create the tcp_clamp_rto_to_user_timeout() helper routine. To calculate
the correct rto, so that the TCP_USER_TIMEOUT socket option is more
accurate. Taking suggestions and feedback into account from
Eric Dumazet, Neal Cardwell and David Laight. Due to the 1st commit we
can avoid the msecs_to_jiffies() and jiffies_to_msecs() dance.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a seperate helper routine as per Neal Cardwells suggestion. To
be used by the final commit in this series and retransmits_timed_out().
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparatory commit. Part of this series that improves the
socket TCP_USER_TIMEOUT option accuracy. Implement Eric Dumazets idea
to convert icsk->icsk_user_timeout from jiffies to msecs. To eliminate
the msecs_to_jiffies() and jiffies_to_msecs() dance in future.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some time now, if you load the bonding driver and configure bond
parameters via sysfs using minimal config options, such as specifying
nothing but the mode, relying on defaults for everything else, modes
that cannot use arp monitoring (802.3ad, balance-tlb, balance-alb) all
wind up with both arp_interval=0 (as it should be) and miimon=0, which
means the miimon monitor thread never actually runs. This is particularly
problematic for 802.3ad.
For example, from an LNST recipe I've set up:
$ modprobe bonding max_bonds=0"
$ echo "+t_bond0" > /sys/class/net/bonding_masters"
$ ip link set t_bond0 down"
$ echo "802.3ad" > /sys/class/net/t_bond0/bonding/mode"
$ ip link set ens1f1 down"
$ echo "+ens1f1" > /sys/class/net/t_bond0/bonding/slaves"
$ ip link set ens1f0 down"
$ echo "+ens1f0" > /sys/class/net/t_bond0/bonding/slaves"
$ ethtool -i t_bond0"
$ ip link set ens1f1 up"
$ ip link set ens1f0 up"
$ ip link set t_bond0 up"
$ ip addr add 192.168.9.1/24 dev t_bond0"
$ ip addr add 2002::1/64 dev t_bond0"
This bond comes up okay, but things look slightly suspect in
/proc/net/bonding/t_bond0 output:
$ grep -i mii /proc/net/bonding/t_bond0
MII Status: up
MII Polling Interval (ms): 0
MII Status: up
MII Status: up
Now, pull a cable on one of the ports in the bond, then reconnect it, and
you'll see:
Slave Interface: ens1f0
MII Status: down
Speed: 1000 Mbps
Duplex: full
I believe this became a major issue as of commit 4d2c0cda07, which for
802.3ad bonds, sets slave->link = BOND_LINK_DOWN, with a comment about
relying on link monitoring via miimon to set it correctly, but since the
miimon work queue never runs, the link just stays marked down.
If we simply tweak bond_option_mode_set() slightly, we can check for the
non-arp modes having no miimon value set, and insert BOND_DEFAULT_MIIMON,
which gets things back in full working order. This problem exists as far
back as 4.14, and might be worth fixing in all stable trees since, though
the work-around is to simply specify an miimon value yourself.
Reported-by: Bob Ball <ball@umich.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbT+cLAAoJEEg/ir3gV/o+I5QH/3LQemGzH33iNsg4khpPeNA+
Q4mGd2jqbwfL17FTSGpTsPje6rpwzR+j8W1fGTx1vzYmE79ZyDu4EwHS7YZJcGyz
q8P0HgrUe4NrJV8mlOpbIRbTuSwfqultw2qRpmCfLf5kK1nqSIPpUHIfBUMqwy0o
O7GJrytUI4Av+r5Px/6bjb5kBaVe5YBe0tg8nSrN2vtzHVQWm+5/uaNRW2SrCN+4
5SI2AsWyMwfGCC+IE8i9OlIFCy6Iu2vwcUabK+6EeGKP4Wb6rukyG01TkQPSd7gy
ozcAjvj+ppHmVFath1uzLCFU3RbKt6GbVRGaFQg5jO5vvK3uzFJnm59Vqw/WzNs=
=UXsy
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-07-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-07-18
The following series provides fixes to mlx5 core and net device driver.
Please pull and let me know if there's any problem.
For -stable v4.7
net/mlx5e: Don't allow aRFS for encapsulated packets
net/mlx5e: Fix quota counting in aRFS expire flow
For -stable v4.15
net/mlx5e: Only allow offloading decap egress (egdev) flows
net/mlx5e: Refine ets validation function
net/mlx5: Adjust clock overflow work period
For -stable v4.17
net/mlx5: E-Switch, UBSAN fix undefined behavior in mlx5_eswitch_mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: updates 2018-07-19
please apply one more round of qeth patches to net-next.
This brings additional performance improvements for the transmit code,
and some refactoring to pave the way for using netdev_priv.
Also, two minor fixes for rare corner cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the L2 OSA xmit path so that it also supports L2 IQD devices
(in particular, their HW header requirements). This allows IQD devices
to advertise NETIF_F_SG support, and eliminates the allocation overhead
for the HW header.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some transmit modes require that the HW header is located in the same
page as the initial protocol headers in skb->data. Let callers specify
the size of this contiguous header range, and enforce it when building
the HW header.
While at it, apply some gentle renaming to the relevant L2 code so that
it matches the L3 code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking whether an skb needs to be linearized to fit into an IO
buffer, it's desirable to consider the skb's final size and layout
(ie. after the HW header was added). But a subsequent linearization can
then cause the re-positioned HW header to violate its alignment
restrictions.
Dealing with this situation in two different code paths is quite tricky.
This patch integrates a) linearize-check and b) HW header construction
into one 3 step-sequence:
1. evaluate how the HW header needs to be added (to identify if it takes
up an additional buffer element), then
2. check if the required buffer elements exceed the device's limit.
Linearize when necessary and re-evaluate the HW header placement.
3. Add the HW header in the best-possible way:
a) push, without taking up an additional buffer element
b) push, but consume another buffer element
c) allocate a header object from the cache.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nowadays an skb fragment typically spans over multiple pages. So replace
the obsolete, SG-only 'fragments' counter with one that tracks the
consumed buffer elements. This is what actually matters for performance.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth's ndo_change_mtu() only applies some trivial bounds checking. Set
up dev->min_mtu properly, so that dev_set_mtu() can do this for us.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MPC initialization code discovers the HW-specific max MTU,
apply the resulting changes straight to the netdevice.
If this is the device's first initialization, also set its MTU
(HiperSockets: the max MTU; else: a layer-specific default value).
Then cap the current MTU by the new max MTU.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice is always available now, so get the portno from there.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocation of the netdevice is currently delayed until a qeth card first
goes online. This complicates matters in several places, where we need
to cache values instead of applying them straight to the netdevice.
Improve on this by moving the allocation up to where the qeth card
itself is created. This is also one step in direction of eventually
placing the qeth card into netdev_priv().
In all subsequent code, remove the now redundant checks whether
card->dev is valid.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the subdriver's remove() routine has completed, the card's layer
mode is undetermined again. Reflect this in the layer2 field.
If qeth_dev_layer2_store() hits an error after remove() was called, the
card _always_ requires a setup(), even if the previous layer mode is
requested again.
But qeth_dev_layer2_store() bails out early if the requested layer mode
still matches the current one. So unless we reset the layer2 field,
re-probing the card back to its previous mode is currently not possible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By updating q->used_buffers only _after_ do_QDIO() has completed, there
is a potential race against the buffer's TX completion. In the unlikely
case that the TX completion path wins, qeth_qdio_output_handler() would
decrement the counter before qeth_flush_buffers() even incremented it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a build warning in toshiba_acpi.c when CONFIG_PROC_FS is not enabled
by marking the unused function as __maybe_unused.
../drivers/platform/x86/toshiba_acpi.c:1685:12: warning: 'version_proc_show' defined but not used [-Wunused-function]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Azael Avalos <coproscefalo@gmail.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Salil Mehta says:
====================
Misc. cleanups for HNS3 ethernet driver
This patch-set presents some cleanups for HNS3 Ethernet Driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SPDX identifiers to HNS3 PF driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct hclge_desc_cb and hclge_desc_cb are never used in
anywhere. This patch removes them.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input parameter "dev" of hns3_irq_handle() is indeed
used as a tqp vector, it is misleadin.
The struct member "flag" is used to indicate ring type,
so rename it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BIT() and GENMASK() to convert the bit mask, modify
the inconsistent ones, and remove useless ones.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using hex for bit offsets is inconsistent with the rest
of the file. Change them to decimal.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some comment spelling errors, removes
redundant comments, rewrites misleading comments, and
adds some necessary comments.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove extra space and brackets.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply the standard minor cleanup by returning ret outside
the brackets.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some redundant assignments, because they have
been set to zero when allocate hdev.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more maintainable by performing more of the signal
related work in send_sigqueue.
A quick inspection of do_timer_create will show that this code path
does not lookup a thread group by a thread's pid. Making it safe
to find the task pointed to by it_pid with "pid_task(it_pid, type)";
This supports the changes needed in fork to tell if a signal was sent
to a single process or a group of processes.
Having the pid to task transition in signal.c will also make it easier
to sort out races with de_thread and and the thread group leader
exiting when it comes time to address that.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In good_sigevent directly compute the default return value as
"task_tgid(current)". This is exactly the same as
"task_pid(current->group_leader)" but written more clearly.
In the thread case first compute the thread's pid. Then veify that
attached to that pid is a thread of the current thread group.
This has the net effect of making the code a little clearer, and
making it obvious that posix timers never look up a process by a the
pid of a thread.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
When f_setown is called a pid and a pid type are stored. Replace the use
of PIDTYPE_PID with PIDTYPE_TGID as PIDTYPE_TGID goes to the entire thread
group. Replace the use of PIDTYPE_MAX with PIDTYPE_PID as PIDTYPE_PID now
is only for a thread.
Update the users of __f_setown to use PIDTYPE_TGID instead of
PIDTYPE_PID.
For now the code continues to capture task_pid (when task_tgid would
really be appropriate), and iterate on PIDTYPE_PID (even when type ==
PIDTYPE_TGID) out of an abundance of caution to preserve existing
behavior.
Oleg Nesterov suggested using the test to ensure we use PIDTYPE_PID
for tgid lookup also be used to avoid taking the tasklist lock.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Everywhere except in the pid array we distinguish between a tasks pid and
a tasks tgid (thread group id). Even in the enumeration we want that
distinction sometimes so we have added __PIDTYPE_TGID. With leader_pid
we almost have an implementation of PIDTYPE_TGID in struct signal_struct.
Add PIDTYPE_TGID as a first class member of the pid_type enumeration and
into the pids array. Then remove the __PIDTYPE_TGID special case and the
leader_pid in signal_struct.
The net size increase is just an extra pointer added to struct pid and
an extra pair of pointers of an hlist_node added to task_struct.
The effect on code maintenance is the removal of a number of special
cases today and the potential to remove many more special cases as
PIDTYPE_TGID gets used to it's fullest. The long term potential
is allowing zombie thread group leaders to exit, which will remove
a lot more special cases in the code.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
To access these fields the code always has to go to group leader so
going to signal struct is no loss and is actually a fundamental simplification.
This saves a little bit of memory by only allocating the pid pointer array
once instead of once for every thread, and even better this removes a
few potential races caused by the fact that group_leader can be changed
by de_thread, while signal_struct can not.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The cost is the the same and this removes the need
to worry about complications that come from de_thread
and group_leader changing.
__task_pid_nr_ns has been updated to take advantage of this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
arm64's new use of KVMs get_events/set_events API calls isn't just
or RAS, it allows an SError that has been made pending by KVM as
part of its device emulation to be migrated.
Wire this up for 32bit too.
We only need to read/write the HCR_VA bit, and check that no esr has
been provided, as we don't yet support VDFSR.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Dongjiu Geng <gengdongjiu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>