With OPP core now supporting DVFS for IO devices, we have instances of
IO devices (same IP block) which require an OPP on some platforms/SoCs
while just needing to scale the clock on some others.
In order to avoid conditional code in every driver which supports such
devices (to check for availability of OPPs and then deciding to do
either dev_pm_opp_set_rate() or clk_set_rate()) add support to manage
empty OPP tables with a clk handle.
This makes dev_pm_opp_set_rate() equivalent of a clk_set_rate() for
devices with just a clk and no OPPs specified, and makes
dev_pm_opp_set_rate(0) bail out without throwing an error.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Move away from the deprecated API and remove printing a stale 'ret'
value.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
MAC80211/CFG80211 framework requires loading regulatory.db from
/lib/firmware directory, so it makes very little sense to have it
built-in. Change it to be built as modules to let it properly load the
needed firmware/db files. As a side effect of this change, the size of
the compressed modules on SquashFS increased significantly from 27MiB
to 38MiB, so increase the size of BLK_DEV_RAM to allow the modules to
fit into it.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We had written "Mangagment" rather than "Management".
Signed-off-by: Sachin Agarwal <asachin591@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Baytrail.
Fixes: c501d0b149 ("pinctrl: baytrail: Add pin control operations")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It appears that SPT-H variant has different offset for PAD locking registers.
Fix it here.
Fixes: 551fa5801e ("pinctrl: intel: sunrisepoint: Add Intel Sunrisepoint-H support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit a8be2af021 ("pinctrl: samsung: Write external wakeup interrupt
mask") started writing the eint wakeup mask from the pinctrl driver.
Unfortunately, it made the assumption that the private retention data
was always a regmap while in the case of s5pv210 it is a raw pointer
to the clock base (as the eint wakeup mask not in the PMU as with newer
Exynos platforms).
Fixes: a8be2af021 ("pinctrl: samsung: Write external wakeup interrupt mask")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for BCM4330/2 SDIO chip on SDHCI bus #3 and the required MMC
power sequence node for the Exynos4210-based UniversalC210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for BCM43342A SDIO chip on MSHC bus #1 and the required MMC
power sequence node for the Exynos3250-based Rinato board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
mshc_0 node doesn't have any children, so there is no need for address
and size-cells properties.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove the 'interrupts' and 'interrupts-parent' properties, which have
been superseded by the interrupts-extended property. While touching this,
fix the interrupts flags to correctly describe the hardware.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Both CPU-freq and dev-freq drivers support proper regulator lookup from
device-tree, so the early introduced hacks for registering main ARM VDD
regulator under 'vdd_arm' name are no longer needed. Similar for devfreq.
Fix this by removing the obsolete comments and changing the regulator
names to the one, which match the schematics and style for the given
board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The updated "i2c-gpio" driver bindings require to define the SDA and SCL
GPIO lines in the separate properties and mark both as GPIO_OPEN_DRAIN.
Covert all Exynos dts files to follow this style.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
GPIO lines for the CM36651 sensor I2C bus use the normal not the inverted
polarity. This bug has been there since adding the CM36651 sensor by
commit 85cb4e0bd2 ("ARM: dts: add cm36651 light/proximity sensor node
for exynos4412-trats2"), but went unnoticed because the "i2c-gpio"
driver ignored the GPIO polarity specified in the device-tree.
The recent conversion of "i2c-gpio" driver to the new, descriptor based
GPIO API, automatically made it the DT-specified polarity aware, what
broke the CM36651 sensor operation.
Fixes: 85cb4e0bd2 ("ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2")
CC: stable@vger.kernel.org # 4.16+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for BCM4330/3 SDIO chip on SDHCI bus #3 and the required MMC
power sequence node for the Exynos4210-based Trats board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for the BCM43342A Bluetooth chip on the serial bus #0 on
the Exynos3250-based Rinato board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add devicetree file for the Exynos4210 based Galaxy S2 (GT-I9100
version).
Signed-off-by: Stenkin Evgeniy <stenkinevgeniy@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add compatible string for the Samsung Galaxy S2 (GT-I9100 version), which
is an Exynos4210 based device.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable serial bus and BCM HCIUART Bluetooth drivers available on the
Exynos3250-based Rinato board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Now all is using the shiny new macros.
No code changed:
# arch/x86/kernel/smpboot.o:
text data bss dec hex filename
16432 2649 40 19121 4ab1 smpboot.o.before
16432 2649 40 19121 4ab1 smpboot.o.after
md5:
a58104003b72c1de533095bc5a4c30a9 smpboot.o.before.asm
a58104003b72c1de533095bc5a4c30a9 smpboot.o.after.asm
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200324185836.GI22931@zn.tnic
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl6TbaUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhgkH/iWpiKvosA20HJjC
rBqYeJPxQsgZTuBieWJ+MeVxbpcF7RlM4c+glyvg3QJhHwIEG58dl6LBrQbAyBAR
aFHNojr1iAYOruVCGnU3pA008YZiwUIDv/ZQ4DF8fmIU2vI2mJ6qHBv3XDl4G2uR
Nwz8Eu9AgIwZM5coomVOSmoWyFy7Vxmb7W+3t5VmKsvOWx4ib9kyQtOIkvQDEl7j
XCbWfI0xDQr6LFOm4jnCi5R/LhJ2LIqqIvHHrunbpszM8IwK797jCXz4im+dmd5Y
+km46N7a8pDqri36xXz1gdBAU3eG7Pt1NyvfjwRVTdX4GquQ2MT0GoojxbLxUP3y
3pEsQuE=
=whbL
-----END PGP SIGNATURE-----
Merge tag 'v5.7-rc1' into locking/kcsan, to resolve conflicts and refresh
Resolve these conflicts:
arch/x86/Kconfig
arch/x86/kernel/Makefile
Do a minor "evil merge" to move the KCSAN entry up a bit by a few lines
in the Kconfig to reduce the probability of future conflicts.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Rockchip platform code is not a clock provider, and just needs to
call of_clk_init().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200212100830.446-5-geert+renesas@glider.be
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The following changes prevent the unrecoverable freezes and rcu_sched
stall warnings experienced in each of my attempts to take advantage of
lima.
Replace the COMPOSITE_NOGATE definition of aclk_gpu_pre with a
COMPOSITE that retains the selection of HDMIPHY as the PLL source, but
instead makes uses of the aclk_gpu PLL source gate and parent names
defined by mux_pll_src_4plls_p rather than mux_aclk_gpu_pre_p.
Remove the now unused mux_aclk_gpu_pre_p and the four named but also
unused definitions (cpll_gpu, gpll_gpu, hdmiphy_gpu and usb480m_gpu)
of the aclk_gpu PLL source gate.
Use the correct gate offset for aclk_gpu and aclk_gpu_noc.
Fixes: 307a2e9ac5 ("clk: rockchip: add clock controller for rk3228")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
[double-checked against SoC manual and added fixes tag]
Link: https://lore.kernel.org/r/20200114162503.7548-1-justin.swartz@risingedge.co.za
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rbd_notify_op_lock() isn't interested in a notify reply. Instead of
accepting that page vector just to free it, have watch-notify code take
care of it.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
rbd_dev->opts is used to distinguish between the image that is being
mapped and a parent. However, because we no longer establish watch for
read-only mappings, this test is imprecise and results in unnecessary
rbd_unregister_watch() calls.
Make it consistent with need_watch in rbd_dev_image_probe().
Fixes: b9ef2b8858 ("rbd: don't establish watch for read-only mappings")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
rbd_dev_unprobe() is supposed to undo most of rbd_dev_image_probe(),
including rbd_dev_header_info(), which means that rbd_dev_header_info()
isn't supposed to be called after rbd_dev_unprobe().
However, rbd_dev_image_release() calls rbd_dev_unprobe() before
rbd_unregister_watch(). This is racy because a header update notify
can sneak in:
"rbd unmap" thread ceph-watch-notify worker
rbd_dev_image_release()
rbd_dev_unprobe()
free and zero out header
rbd_watch_cb()
rbd_dev_refresh()
rbd_dev_header_info()
read in header
The same goes for "rbd map" because rbd_dev_image_probe() calls
rbd_dev_unprobe() on errors. In both cases this results in a memory
leak.
Fixes: fd22aef8b4 ("rbd: move rbd_unregister_watch() call into rbd_dev_image_release()")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
rbd_unregister_watch() flushes notifies and therefore cannot be called
under header_rwsem because a header update notify takes header_rwsem to
synchronize with "rbd map". If mapping an image fails after the watch
is established and a header update notify sneaks in, we deadlock when
erroring out from rbd_dev_image_probe().
Move watch registration and unregistration out of the critical section.
The only reason they were put there was to make header_rwsem management
slightly more obvious.
Fixes: 811c668877 ("rbd: fix rbd map vs notify races")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Current code contains a weird hack to avoid switch from 54Mbps CTS to
1Mbps. However, we have not been able to reproduce the problem and
hardware team don't know any defect of this kind. So, it seems this hack
is no more necessary.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-33-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When driver has Content After DTIM Beacon (CAB) in queue, it wait for an
indication from the firmware. However, when we stop to send beacons,
this indication may never happen.
Solve this issue by simply simulate this indication. Firmware will send
data that probably nobody will heard.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-32-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wfx_tx_flush() wait there are no more frame in device buffer. However,
this event may never happens since wfx_tx_flush() don't forbid to
enqueue new frames.
Note that wfx_tx_flush() should only ensure that all frames currently in
hardware queues are sent. So the current code is more restrictive that
it should.
Note that wfx_tx_flush() release the lock before to return while
wfx_tx_lock_flush() keep the lock.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-31-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wfx_flush() exited once all frames are retrieved from the device.
However, it did not ensure they were processed by driver before to
return. Therefore, some frame may be processed after the interface has
disappear.
Change the place we signal that the queue is empty to fix that.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-30-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, wfx_flush() flushed queue for while device instead of only
the queue of the intended vif. It sometime failed with a timeout, but
this error was not reported.
Moreover, if the device was frozen, wfx_flush didn't do anything and it
results a potential warning (and maybe a resource leak) when the frozen
device was unregistered.
We can also notice that wfx_tx_queues_wait_empty_vif() did only exist to
work around the broken feature of wfx_flush().
This patch repair wfx_flush() and therefore drop
wfx_tx_queues_wait_empty_vif().
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-29-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a next commit, we would like to mark wfx_skb_dtor as static and stop
to declare it in data_tx.h.
Relocate wfx_skb_dtor() prior its callers to avoid compile error.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-28-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, wfx_pending_remove() (from queue.c) call wfx_skb_dtor()
(from data_tx.c) that forward the tx status to mac80211.
Moreover, there no purpose to retrieve a frame from the pending queue
without dequeuing it. So, the main purpose of wfx_pending_remove() is to
forward the tx status to mac80211.
Let's make the architecture cleaner:
- merge wfx_pending_remove() into wfx_pending_get()
- call wfx_skb_dtor() from data_tx.c
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-27-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The queue used for wfx_tx_queue_put() can be deducted from the content
of the skb. So drop this parameter from call to wfx_tx_queues_put().
In add, this change uniformizes usage of functions wfx_tx_queues_*.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-26-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to keep the intermediate struct wfx_queue_stats.
Relocate its members to struct wfx_dev.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-25-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we do not rely in QoS parameters to choose which frame to send, it
is no more necessary to keep a copy of EDCA parameters.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-24-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code computes itself the QoS policy to choose which frame
should be sent. However, firmware already do that job. Firmware would
prefer to have packets in every queues and be able to choose itself
which queue to use.
So, this patch sort the queues from the emptiest to the fulliest (thanks
to the pending frames counter introduced a few commits earlier). It send
frame to the least full queue.
However, we continue to be careful with frames that have to be sent
after a dtim ("cab": Content After (DTIM) Beacon).
So, this patch splits AC queues in two skb_queues: one for normal frames
and another for cab frames. It cares to send frames from CAB skb_queue
if appropriate.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-23-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This counter will be useful to know which queue is least full in a
further patch.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-22-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not necessary to return a skb. Just getting the information if
there is traffic to be sent after DTIM is sufficient.
In add, the acronym "cab" (Content After (DTIM) Beacon) is used in
mac80211 to designate this kind of traffic.
So, make wfx_tx_queues_get_after_dtim() return a boolean and rename
accordingly.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200401110405.80282-21-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
