According to documentation REMAP register has to be programmed in
either DMA or PIO mode of the slice.
Move the DMA capability check below to let REMAP register be programmed
in PIO mode.
Cc: stable@vger.kernel.org # 4.3+
Fixes: 4b45efe852 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros_ec_i2c driver is still active after it had suspended or before it
resumes. Besides that, it also tried to transfer data even after the I2C
host had been suspended. This will lead the system to crash.
During the test, we also observe that the EC needs to be resumed earlier
due to some status polling from the EC FW (e.g. battery status). So we
move the PM ops to late stage to make it work normally.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reboot or shutdown during delayed works could corrupt communication with
EC and certain I2C controller may not be able to recover from the error
state.
This patch registers a shutdown callback used to cancel the debugfs log
worker thread.
Signed-off-by: Daniel Hung-yu Wu <hywu@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Check whether this EC instance has RTC host command support and instatiate
the RTC driver as a subdevice in such case.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We should stop our worker thread while we're suspended. If we don't
then we'll get messages like:
cros-ec-spi spi5.0: spi transfer failed: -108
cros-ec-spi spi5.0: cs-deassert spi transfer failed: -108
cros-ec-ctl cros-ec-ctl.0.auto: EC communication failed
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Free the IRQ we might have requested when removing the cros_ec device,
so we can unload and reload the driver properly.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we cannot communicate with the EC chip to detect the protocol version
and its features, it's very likely useless to continue. Else we will
commit all kind of uninformed mistakes (using the wrong protocol, the
wrong buffer size, mixing the EC with other chips).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The string.h header file is needed for the memset() definition. The RT
build fails because it is not pulled in via other header files.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add an entry to make myself a maintainer of STM32 timer and lptimer
drivers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, USB-audio driver allocates the PCM buffer via vmalloc(), as
this serves merely as an intermediate buffer that is copied to each
URB transfer buffer. This works well in general on x86, but on some
archs this may result in cache coherency issues when mmap is used.
OTOH, it works also on such arch unless mmap is used.
This patch is a step for mitigating the inconvenience; a new module
option "use_vmalloc" is provided so that user can choose to allocate
the DMA coherent buffer instead of the existing vmalloc buffer.
The drawback is that it'd be the standard dma_alloc_coherent() calls
and the system would require contiguous pages on non-x86 archs.
Note that it's a global option and not dynamically switchable since
the buffer is pre-allocated at the probe time. In theory, it's
possible to be switchable, but it'd be trickier and racier.
As default use_vmalloc option is set to true, so that the old behavior
is kept. For allowing the coherent mmap on ARM or MIPS, pass
use_vmalloc=0 option explicitly.
Reported-and-tested-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power-saving is causing a humming sound when active on the Intel
NUC5i7RY, add it to the blacklist.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199607
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When there are 16 or more logical CPUs, we request for
`IWL_MAX_RX_HW_QUEUES` (16) IRQs only as we limit to that number of
IRQs, but later on we compare the number of IRQs returned to
nr_online_cpus+2 instead of max_irqs, the latter being what we
actually asked for. This ends up setting num_rx_queues to 17 which
causes lots of out-of-bounds array accesses later on.
Compare to max_irqs instead, and also add an assertion in case
num_rx_queues > IWM_MAX_RX_HW_QUEUES.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199551
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Hao Wei Tee <angelsl@in04.sg>
Tested-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit fb47ada8dc.
In some situations when we set TXOP_BACKOFF, the probe frame is
not sent at all. What it worse then sending probe frame as part
of AMPDU and can degrade 11n performance to 11g rates.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove and refactor some code in order to avoid having identical code
for different branches.
Notice that the logic has been there since 2014.
Addresses-Coverity-ID: 1426199 ("Identical code for different branches")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add some tracepoints so we can inspect what is not working as is should.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Message-Id: <20180523025645.8978-5-bjsdjshi@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's avoid free on ccw->cda that points to a guest address
or an already freed memory area by setting it to NULL if memory
allocation didn't happen or failed.
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Message-Id: <20180523025645.8978-4-bjsdjshi@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This refactors pfn_array_alloc_pin() and also improves it by adding
defensive code in error handling so that calling pfn_array_unpin_free()
after error return won't lead to problem. This mainly does:
1. Merge pfn_array_pin() into pfn_array_alloc_pin(), since there is no
other user of pfn_array_pin(). As a result, also remove kernel-doc
for pfn_array_pin() and add/update kernel-doc for pfn_array_alloc_pin()
and struct pfn_array.
2. For a vfio_pin_pages() failure, set pa->pa_nr to zero to indicate
zero pages were pinned.
3. Set pa->pa_iova_pfn to NULL right after it was freed.
Suggested-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Message-Id: <20180523025645.8978-3-bjsdjshi@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The kernel doc description for usage of the struct pfn_array in
pfn_array_pin() is unnecessary long. Let's shorten it by describing
the contents of the struct pfn_array fields at the struct's definition
instead.
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Message-Id: <20180523025645.8978-2-bjsdjshi@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
There is at least one relevant guest OS that doesn't set the IDA flags in
the ORB as we would like them, but never uses any IDA. So instead of
saying -EOPNOTSUPP when observing an ORB, such that a channel program
specified by it could be a not supported one, let us say -EOPNOTSUPP only
if the channel program is a not supported one.
Of course, the real solution would be doing proper translation for all
IDA. This is possible, but given the current code not straight forward.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Jason J. Herne <jjherne@linux.ibm.com>
Message-Id: <20180516173342.15174-1-pasic@linux.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If the device has not been registered, or there is work pending,
we should reschedule a sch_event call again.
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20180502072559.50691-1-bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Active scan is not allowed on radar channel, instead
using passvie scan with more time.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware does not support embedded supplicant, then it in turn
will not support GT rekey offloading. If this is the case, then
driver must not advertise WOWLAN flags related to GTK rekey and
it must also skip sending the GT_REKEY_OFFLOAD_CFG command.
Signed-off-by: Shrenik Shikhare <shrenik@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Race condition is observed during rmmod of mwifiex_usb:
1. The rmmod thread will call mwifiex_usb_disconnect(), download
SHUTDOWN command and do wait_event_interruptible_timeout(),
waiting for response.
2. The main thread will handle the response and will do a
wake_up_interruptible(), unblocking rmmod thread.
3. On getting unblocked, rmmod thread will make rx_cmd.urb = NULL in
mwifiex_usb_free().
4. The main thread will try to resubmit rx_cmd.urb in
mwifiex_usb_submit_rx_urb(), which is NULL.
To fix, wait for main thread to complete before calling
mwifiex_usb_free().
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a follow-up patch for commit 21c5c83ce8
("mwifiex: support sysfs initiated device coredump").
Let us avoid exporting mwifiex_send_cmd and instead use a utility
function mwifiex_fw_dump_event to achive the work.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in rsi_dbg message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add pci_disable_device in error handling while init_atmel_card failed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In former patch, I enqueu all C2H commands and processed by a workqueue.
In case C2H_BT_INFO will issue a H2C command to set BT reg, and wait for
a C2H ack. But it is totally impossible that C2H workqueue waits for a
C2H command, so kernel log warn
rtlwifi: :<0> btmpinfo wait (req_num=0) timeout
Since the C2H ack command C2H_BT_MP can be safely processed in interrupt
context, add a fast command path to deal with the command.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The format of C2H data is ID(1 byte) + Length(1 byte) + value, and it is
more readable to use macros to access C2H data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We use 'struct rtl_c2hcmd' to store C2H commands originally, and the code
is slightly complex to enqueue and dequeue and also wastes time to
allocate and memcpy data. Since C2H commands are asynchronous events,
they can be processed in work queue, so RX ISR enqueues C2H result in
removal of rtl_c2h_packet_handler().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Similar to rx_command_packet, we can call rtl_c2h_content_parsing so the
hal_op isn't necessary.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Because the hal_op rx_command_packet does C2H handler if rx packet type
is C2H, and the handler have been moved to base.c so we can call the
handler directly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Merge duplicate C2H handler and implement the handler in base.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We're going to merge C2H handler into one, but one special case is to
handle RA_REPORT that implements in individual IC folder. So this commit
adds a hal_op for caller in common code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The caller of hal_op rx_command_packet will assert function pointer
before calling, so we can remove dummy functions safely.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IDs are defined by driver and map to the fw C2H IDs, but they aren't
used now result in removal.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move C2H definition to wifi.h, because the definitions of 8192ee, 8723be
and 8821ae are the same.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current chips use packet-based C2H commands whose IDs differ from old
ones, so this commit simply gives C2H_V0_ as prefix of command IDs.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move duplicate definitions from def.h of ic folder to wifi.h
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To use keep-alive mechanism in mac80211 stack, since driver supports
reporting accurate nullfunc frame tx ack now.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to realize the keep-alive mechanism in mac80211 stack, reporting
accurate tx ack status for nullfunc frame is added in this commit.
If current frame is nullfunc frame, we ask firmware to report by filling
TX report bit in TX descriptor. After this frame DMA done, TX interrupt is
triggered but TX status is unknown at this moment, so enqueue this skb
into tx_report->queue. Finally, C2H report will be received if the frame
is transmitted successfully or retried over, and then we report to mac80211
with IEEE80211_TX_STAT_ACK flag only if it's successful. Otherwise, if
failure or timeout (one second), we report to mac80211 without this flag.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can have pm_runtime_get_sync() return 1, and we can have
pm_runtime_put_sync() return -EBUSY. See rpm_suspend() and
rpm_resume() for more information.
Fix the issue by returning 0 from wl12xx_sdio_power_on() on success.
And use pm_runtime_put() instead of pm_runtime_put_sync() for
wl12xx_sdio_power_off(), then the MMC subsystem will idle the bus
when suitable.
Otherwise wlcore can sometimes get confused and may report bogus
errors and WLAN connection can fail.
Note that while wlcore checks the return value for wl1271_power_on(),
the return value is ignored for wl1271_power_off(). Let's fix them
both though to avoid further confusion in the future.
Fixes: 60f36637bb ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
commit 1c8f422059 ("mm: change return type to vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180510134203.GA25166@jordon-HP-15-Notebook-PC
gcc-8 warns that pcm_instance->name is not necessarily terminated correctly
if the input is more than 80 characters long or lacks a termination byte
itself:
In function 'strncpy',
inlined from 'cfg_device' at sound/xen/xen_snd_front_cfg.c:399:3,
inlined from 'xen_snd_front_cfg_card' at sound/xen/xen_snd_front_cfg.c:509:9:
include/linux/string.h:254:9: error: '__builtin_strncpy' specified bound 80 equals destination size [-Werror=stringop-truncation]
return __builtin_strncpy(p, q, size);
Using strlcpy() instead of strncpy() makes this a bit safer.
Fixes: fd3b36045c ("ALSA: xen-front: Read sound driver configuration from Xen store")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the 'device_config' and 'device_prep_slave_sg' interfaces
for users to configure DMA, as well as adding one 'struct sprd_dma_config'
structure to save Spreadtrum DMA configuration for each DMA channel.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>