Use named constants instead of integers in call_fext_func() invocations
related to backlight power control in order to more clearly convey the
intent of each call.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Do not include linux/slab.h as all module code now uses managed memory
allocations and thus neither k*alloc() nor kfree() is used.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
In order to improve code clarity, move declarations of variables that
are module parameters higher up and add a comment.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Replace the last few lines of acpi_fujitsu_bl_add() with a simple return
in order to improve code readability without changing the logic.
As acpi_fujitsu_laptop_add() uses a managed memory allocation for
device-specific data, it is fine to just return immediately upon kfifo
allocation failure. Do that instead of jumping to the end of the
function to improve code readability. Running out of memory while
allocating the kfifo does not seem probable enough to warrant logging an
error message, so do not do it.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Only register input devices after the device-specific data structures
they access are fully initialized.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Different functions in the module use varying names (error, result,
status) for a local variable storing the return value of a function call
that has to be checked for errors. Use a common name (ret) for all
these local variables to improve code consistency. Merge integer
variable declarations in acpi_fujitsu_laptop_add() into one line.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This patch fixes the checkpatch.pl warning:
drivers/staging/iio/meter/ade7854.h:157: WARNING: function definition
argument 'struct device *' should also have an identifier name...
This commit adds arguments names to the signature declared in the
ade7854_state struct. For consistency reason, It also renames all
arguments in function definitions.
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This shouldn't affect runtime at all, but Smatch complains that we
should check if mlx90632_read_ambient_raw() otherwise we
"ambient_new_raw" can be uninitialized.
drivers/iio/temperature/mlx90632.c:509 mlx90632_calc_ambient_dsp105()
error: uninitialized symbol 'ambient_new_raw'.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Dynamic debug has a run time knob to enable function name printing.
Remove this from dev_dbg() calls.
Furthermore, functional tracing when enabled can show what function is
called, therefore remove empty dev_dbg() calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
io-channel-cells should be <0> since sigma delta modulator exports only
one channel, as described in ../iio/iio-bindings.txt "IIO providers"
section. Only the phandle is necessary for IIO consumers in this case.
Fixes: af11143757 ("IIO: Add DT bindings for sigma delta adc modulator")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When several channels are registered (e.g. via st,adc-channels property):
- channels array is wrongly filled in. Only 1st element in array is being
initialized with last registered channel.
Fix it by passing reference to relevant channel (e.g. array[index]).
- only last initialized channel can work properly (e.g. unique 'ch_id'
is used). Converting any other channel result in conversion timeout.
Fix it by getting rid of 'ch_id', use chan->channel instead.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
!!'s behaviour isn't that obvious and sparse complained about it, so
let's replace it with a ternary condition.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
CCS811 has different I2C register maps in boot and application mode. When
CCS811 is in boot mode, register APP_START (0xF4) is used to transit the
firmware state from boot to application mode. However, APP_START is not a
valid register location when CCS811 is in application mode (refer to
"CCS811 Bootloader Register Map" and "CCS811 Application Register Map" in
CCS811 datasheet). The driver should not attempt to perform a write to
APP_START while CCS811 is in application mode, as this is not a valid or
documented register location.
When prob function is being called, the driver assumes the CCS811 sensor
is in boot mode, and attempts to perform a write to APP_START. Although
CCS811 powers-up in boot mode, it may have already been transited to
application mode by previous instances, e.g. unload and reload device
driver by the system, or explicitly by user. Depending on the system
design, CCS811 sensor may be permanently connected to system power source
rather than power controlled by GPIO, hence it is possible that the sensor
is never power reset, thus the firmware could be in either boot or
application mode at any given time when driver prob function is being
called.
This patch checks the STATUS register before attempting to send a write to
APP_START. Only if the firmware is not in application mode and has valid
firmware application loaded, then it will continue to start transiting the
firmware boot to application mode.
Signed-off-by: Richard Lai <richard@richardman.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The resistance member in ccs811_reading struct is an unsigned 16-bit
integer variable used to store RAW_DATA register bytes read from CCS811.
It is kind of misleading to name this struct member as resistance.
About the RAW_DATA register bytes, the CCS811 datasheet states that:
-----
Two byte read only register which contains the latest readings from the
sense resistor.
The most significant 6 bits of the Byte 0 contain the value of the current
through the sensor (0μA to 63μA).
The lower 10 bits contain (as computed from the ADC) the readings of the
voltage across the sensor with the selected current (1023 = 1.65V)"
-----
Hence, the RAW_DATA register byte contains information about electric
current and voltage of the CCS811 sensor. Calling this struct member
'resistance' is kind of misleading, although both electric current and
voltage are needed to calculate the electrical resistance of the sensor
using Ohm's law, V = I x R, in which a new channel type of IIO_RESISTANCE
may be added to the driver in the future.
Signed-off-by: Richard Lai <richard@richardman.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The capture interface doesn't work and the playback interface only
supports 48 kHz sampling rate even though it advertises more rates.
Signed-off-by: Erik Veijola <erik.veijola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes the wrongly included dtsi file which
was breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS.
As per the board name, the correct file should be imx6dl.dtsi instead
of imx6q.dtsi
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 7a9caba55a ("ARM: dts: imx6dl: Add Engicam i.CoreM6 DualLite/Solo RQS initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the "i.MX 6Solo/6DualLite Applications Processor
Reference Manual" Rev. 3, 09/2017 there is no LCDIF unit on the
i.MX6DL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no pinctrl_usbotg_2 node in current Hummingboard dts files.
Drop reference to that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the USBOTG-ID pin to the correct definition. The top
USB port stays in device-mode without this change.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit name in order to fix the following
dtc warning with W=1:
arch/arm/boot/dts/imx28-tx28.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Re-sync the defconfig by doing:
make savedefconfig
cp defconfig arch/arm/configs/imx_v6_v7_defconfig
Checked that all the removed options are still enabled by Kconfig logic.
The exception is CONFIG_SOC_CAMERA_OV2640, which is only used by some
mx31 machines. As the mx3_camera driver has been removed from the kernel
tree, removing CONFIG_SOC_CAMERA_OV2640 is not an issue.
So keep it in sync to help further changes in defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
They aren't needed by the etnaviv driver anymore and have been removed
from the binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
None of the slots support 1.8V signaling or SDIO. There is no point in
probing for a SD card on the eMMC controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for Advantech DMS-BA16 board, which uses
the Advantech BA-16 module.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PSCI standard v0.2, for CPU_SUSPEND call, which is
used by cpu idle framework, bit[16] of state parameter must be 0.
So update bit[16] of property 'arm,psci-suspend-param', which is
used as state parameter, to 0.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Daniel Borkmann says:
====================
Couple of minor improvements to the x64 JIT I had still around from
pre merge window in order to shrink the image size further. Added
test cases for kselftests too as well as running Cilium workloads on
them w/o issues.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add few test cases that check the rnu-time results under JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
While it's rather cumbersome to reduce prologue for cBPF->eBPF
migrations wrt spill/fill for r15 which is callee saved register
due to bpf_error path in bpf_jit.S that is both used by migrations
as well as native eBPF, we can still trivially save 5 bytes in
prologue for the former since tail calls can never be used there.
cBPF->eBPF migrations also have their own custom prologue in BPF
asm that xors A and X reg anyway, so it's fine we skip this here.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a generic emit_mov_reg() helper in order to reuse it in BPF
multiplication to load the src into rax, we can save a few bytes
in alu32 while doing so.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Instead of unconditionally performing push/pop on rax/rdx
in case of multiplication, we can save a few bytes in case
of dest register being either BPF r0 (rax) or r3 (rdx)
since the result is written in there anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
While analyzing some of the more complex BPF programs from Cilium,
I found that LLVM generally prefers to emit LD_IMM64 instead of MOV32
BPF instructions for loading unsigned 32-bit immediates into a
register. Given we cannot change the current/stable LLVM versions
that are already out there, lets optimize this case such that the
JIT prefers to emit 'mov %eax, imm32' over 'movabsq %rax, imm64'
whenever suitable in order to reduce the image size by 4-5 bytes per
such load in the typical case, reducing image size on some of the
bigger programs by up to 4%. emit_mov_imm32() and emit_mov_imm64()
have been added as helpers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When we shift by one, we can use a different encoding where imm
is not explicitly needed, which saves 1 byte per such op.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In case when dentry passed to lock_parent() is protected from freeing only
by the fact that it's on a shrink list and trylock of parent fails, we
could get hit by __dentry_kill() (and subsequent dentry_kill(parent))
between unlocking dentry and locking presumed parent. We need to recheck
that dentry is alive once we lock both it and parent *and* postpone
rcu_read_unlock() until after that point. Otherwise we could return
a pointer to struct dentry that already is rcu-scheduled for freeing, with
->d_lock held on it; caller's subsequent attempt to unlock it can end
up with memory corruption.
Cc: stable@vger.kernel.org # 3.12+, counting backports
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The SEV LAUNCH_SECRET command fails with error code 'invalid param'
because we missed filling the guest and header system physical address
while issuing the command.
Fixes: 9f5b5b950a (KVM: SVM: Add support for SEV LAUNCH_SECRET command)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-kernel@vger.kernel.org
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RSM instruction is used by the SMM handler to return from SMM mode.
Currently, rsm causes a #UD - which results in instruction fetch, decode,
and emulate. By installing the RSM intercept we can avoid the instruction
fetch since we know that #VMEXIT was due to rsm.
The patch is required for the SEV guest, because in case of SEV guest
memory is encrypted with guest-specific key and hypervisor will not
able to fetch the instruction bytes from the guest memory.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using the access_ok() to validate the input before issuing the SEV
command does not buy us anything in this case. If userland is
giving us a garbage pointer then copy_to_user() will catch it when we try
to return the measurement.
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Fixes: 0d0736f763 (KVM: SVM: Add support for KVM_SEV_LAUNCH_MEASURE ...)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-kernel@vger.kernel.org
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid traversing all the cpus for pv tlb flush when steal time
is disabled since pv tlb flush depends on the field in steal time
for shared data.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The early_param() is only called during kernel initialization, So Linux
marks the functions of it with __init macro to save memory.
But it forgot to mark the parse_no_kvmapf/stealacc/kvmclock_vsyscall,
So, Make them __init as well.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: rkrcmar@redhat.com
Cc: kvm@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: x86@kernel.org
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guests on new hypersiors might set KVM_ASYNC_PF_DELIVERY_AS_PF_VMEXIT
bit when enabling async_PF, but this bit is reserved on old hypervisors,
which results in a failure upon migration.
To avoid breaking different cases, we are checking for CPUID feature bit
before enabling the feature and nothing else.
Fixes: 52a5c155cf ("KVM: async_pf: Let guest support delivery of async_pf from guest mode")
Cc: <stable@vger.kernel.org>
Reviewed-by: Wanpeng Li <wanpengli@tencent.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix the following sparse warning by moving the prototype
of kvm_arch_mmu_notifier_invalidate_range() to linux/kvm_host.h .
CHECK arch/s390/kvm/../../../virt/kvm/kvm_main.c
arch/s390/kvm/../../../virt/kvm/kvm_main.c:138:13: warning: symbol 'kvm_arch_mmu_notifier_invalidate_range' was not declared. Should it be static?
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the kvm_arch_irq_routing_update() prototype outside of
ifdef CONFIG_HAVE_KVM_EVENTFD guards to fix the following sparse warning:
arch/s390/kvm/../../../virt/kvm/irqchip.c:171:28: warning: symbol 'kvm_arch_irq_routing_update' was not declared. Should it be static?
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>