Commit graph

932,869 commits

Author SHA1 Message Date
Alexey Khoroshilov
196644fd09 mtd: nand: vf610: improve readability of error label
Use clearer error labels as Boris Brezillon suggested.

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:05 +01:00
Alexey Khoroshilov
f5a666bdd5 mtd: nand: vf610: remove the unnecessary of_node_put()
Calling of_node_put() in vf610_nfc_probe() is wrong because nothing in
this code retains a reference to the DT node.

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:04 +01:00
Stefan Agner
532a1cf9a0 mtd: nand: vf610_nfc: remove unused function
The function count_written_bits has been replaced by the generic
nand_check_erased_ecc_chunk() function with commit 48c25cf441
("mtd: nand: vf610_nfc: use nand_check_erased_ecc_chunk() helper").
Remove the unused function.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:04 +01:00
Miquel Raynal
07ad5a7214 mtd: nand: add ->setup_data_interface() support for Marvell NFCv1
First generation of Marvell NAND flash controllers (eg. embedded in PXA
boards) did not make use of the NAND core hook ->setup_data_interface()
to setup controller timings. Add support for it.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:03 +01:00
Sascha Hauer
68dc8e41fd mtd: nand: mxc: remove now unused code
Since we now have our own read_page/write_page functions
mxc_nand_command() will no longer be called with NAND_CMD_READ0,
NAND_CMD_READOOB, NAND_CMD_SEQIN and NAND_CMD_PAGEPROG. Remove
the code handling these commands.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:58 +01:00
Sascha Hauer
cd8b465533 mtd: nand: mxc: Drop now unnecessary functions
Since we have our own read_page/write_page functions correct_data and
calculate are no longer needed. Remove them.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:51 +01:00
Sascha Hauer
6811c4642a mtd: nand: mxc: Add own write_page
Now that we have our own read_page function add a write_page function
for consistency aswell. This can be a lot easier than the generic
function since we do not have to iterate over subpages but can write
the whole page at once. Also add write_page_raw and write_oob for
proper raw and oob write support.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:45 +01:00
Sascha Hauer
5039fc9f2d mtd: nand: mxc: Fix failed/corrected values for v1 controllers
The v1 controller code has several flaws:
- We do not forward the number of corrected bitflips to the upper layers
- For 2k page NAND chips only the status results from the fourth subpage
  read are evaluated, so ECC failures in the other subpages remain
  uncovered
- When there are uncorrectable errors we have to increase the statistics
  counter, but still have to return successfully. Currently we return
  an error

This patch fixes this by introducing a v1 specific read_page function.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:38 +01:00
Sascha Hauer
67b87f66ca mtd: nand: mxc: Fix failed/corrected values for v2/v3 controllers
Currently nand_read_page_hwecc() from nand_base calls
mxc_nand_correct_data_v2_v3() for each subpage, but in this function we
return the corrected/failed results for the whole page instead
of a single subpage. On a 2k page size Nand this leads to results which
are 4 times too high.
The whole ecc.calculate/ecc.correct mechanism used by
nand_read_page_hwecc() is not suitable for devices which correct the
data in hardware, so fix this by using a driver specific read_page
function which does the right thing. Also add read_page_raw and read_oob
For proper raw and oob read support.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:34 +01:00
Sascha Hauer
1af0b31474 mtd: nand: mxc: Add buffer argument to copy_spare
With following patches we will have to copy the spare data to/from
other buffers, so add the buffer as argument to copy_spare().

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:28 +01:00
Sascha Hauer
040bd3f6a3 mtd: nand: mxc: Add function to control hardware ECC
For proper raw read/write support need to be able to control the
hardware ECC engine. Add a function to enable/disable it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:24 +01:00
Sascha Hauer
1549333167 mtd: nand: mxc: reorder functions to avoid forward declarations
We'll call copy_spare() and mxc_do_addr_cycle() from another place
during the next patches, so move functions up to avoid forward
declarations.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:04 +01:00
Guenter Roeck
aef17ca127 hwmon: (k10temp) Only apply temperature offset if result is positive
A user reports a really bad temperature on Ryzen 1950X.

k10temp-pci-00cb
Adapter: PCI adapter
temp1: +4294948.3°C (high = +70.0°C)

This will happen if the temperature reported by the chip is lower than
the offset temperature. This has been seen in the field if "Sense MI Skew"
and/or "Sense MI Offset" BIOS parameters were set to unexpected values.
Let's report a temperature of 0 degrees C in that case.

Fixes: 1b50b77635 ("hwmon: (k10temp) Add support for temperature offsets")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2018-02-12 14:23:29 -08:00
Jerome Brunet
266c157de3 arm64: defconfig: enable MESON EFUSE
Enable nvmem meson efuse driver as a module

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:20:43 -08:00
weiyongjun (A)
01517dfc81 meson-gx-socinfo: make local function meson_gx_socinfo_init static
Fixes the following sparse warnings:

drivers/soc/amlogic/meson-gx-socinfo.c💯12: warning:
 symbol 'meson_gx_socinfo_init' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:47 -08:00
weiyongjun (A)
82a759c918 meson-mx-socinfo: Make local function meson_mx_socinfo_init() static
Fixes the following sparse warnings:

drivers/soc/amlogic/meson-mx-socinfo.c:107:12: warning:
 symbol 'meson_mx_socinfo_init' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:47 -08:00
Heiner Kallweit
87f88732d2 soc: amlogic: meson-gx-pwrc-vpu: fix error on shutdown when domain is powered off
When operating the system headless headless, the domain is never
powered on, leaving the clocks disabled. The shutdown function then
tries to disable the already disabled clocks, resulting in errors.
Therefore call meson_gx_pwrc_vpu_power_off() only if domain is
powered on.
This patch fixes the described issue on my system (Odorid-C2).

Fixes: 339cd0ea08 "soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:46 -08:00
Heiner Kallweit
3a2ad7bd31 soc: amlogic: meson-gx-pwrc-vpu: don't print error message on probe deferral
The error message may be misleading in case of probe deferral
(happens on my Odroid-C2). Therefore don't print it in this case.

Fixes: 75fcb5ca4b "soc: amlogic: add Meson GX VPU Domains driver"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:46 -08:00
Jorge Ramirez-Ortiz
059a58fcd5 ARM64: dts: meson: accept MAC addr from u-boot environment
Extend configuring the MAC address from u-boot to all meson boards.

I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.

Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Jorge Ramirez-Ortiz
f7c36209c4 ARM64: dts: meson s905x: accept MAC addr from u-boot environment
With the adequate configuration settings, u-boot will loop through the
list of aliases looking for "ethernetX".

By adding an ethernet alias, u-boot can fixup the local-mac-address
property in the kernel's device tree using a value held in its
environment variable ethaddr.

Tested-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Yixun Lan
3e5925c622 ARM64: dts: meson-axg: enable the UART_A controller
The UART_A is connected to a BT module on the S400 board.

Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Yixun Lan
e496c415a3 ARM64: dts: meson-axg: complete the pinctrl info for UART_AO_A
Explictly request the pinctrl info for the UART_AO_A controller,
otherwise we may need to rely on bootloader for the initialization.

Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Yixun Lan
4eae66a692 ARM64: dts: meson-axg: uart: Add the pinctrl info description
Describe the pinctrl info for the UART controller which is found
in the Meson-AXG SoCs.

Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[khilman: s/uart_ao_b_gpioz/uart_ao_b_z/ ]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Yixun Lan
5866213022 ARM64: dts: meson-axg: uart: drop legacy compatible name from EE UART
When update the clock info for the UART controller in the EE domain,
the driver explicitly require 'pclk' in order to work properly.

With current logic of the code, the driver will go for the legacy clock probe
routine if it find current compatible string match to 'amlogic,meson-uart',
which result in not requesting the 'pclk' clock, thus break the driver in the end.

Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Yixun Lan
777fa58db6 ARM64: dts: meson-axg: add RMII pins for ethernet controller
Comparing to RGMII interface, the RMII interface require few pins.
So it's worth describing them here.

Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Jian Hu
7d6d8a2053 ARM64: dts: meson-axg: enable I2C Master-1 for the audio speaker
In the S400 board, The I2C master-1 is connecting to
the audio speaker daughter board.

Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Jian Hu
8a7669a53e ARM64: dts: meson-axg: describe pin DT info for I2C controller
Describe all the pin mux for the I2C controller which found in
Meson-AXG SoC.

Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:10 -08:00
Jian Hu
dc6f858e26 ARM64: dts: meson-axg: add I2C DT info for Meson-AXG SoC
There are four I2C masters in EE domain, and one I2C Master in
AO domain, the DT info here should describe them all.

Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:09 -08:00
Jerome Brunet
eafd53d315 ARM64: meson-axg: enable hardware rng
Enable the hardware random generator

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:15:09 -08:00
Emiliano Ingrassia
9c15795a4f ARM: dts: meson8b-odroidc1: ethernet support
The Odroid-C1+ board is equipped with an RTL8211F ethernet PHY
which supports 10/100/1000 Mbps ethernet.
The PHY reset and interrupt lines are controlled by the SoC via
two GPIO lines (GPIOH_4 and GPIOH_3 respectively).
The PHY energy efficient ethernet (eee) mode is marked as broken
using "eee-broken-1000t" because, during tests, high packet losses
were experienced without it.

Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:13:36 -08:00
Emiliano Ingrassia
b96446541d ARM: dts: meson8b: extend ethernet controller description
Enable S805 (aka Meson8b) ethernet pin multiplexing and
extend the controller description.
The programmable ethernet (PRG_ETHERNET) register address
value (0xc1108108), contained in meson.dtsi, is overridden
according to the value found in S805 SoC manual.
This also required to switch to "amlogic,meson8b-dwmac" compatible
to correctly configure that register.
The two clock sources "clkin0" and "clkin1" are both equals
to MPLL2 because, as reported in bit 9-7 register description,
that is the only Meson8b ethernet clock source.

Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:13:36 -08:00
Martin Blumenstingl
e1fa57dfd7 ARM: dts: meson8: add the USB reset line
Now that we support the reset controller on Meson8 we can add the reset
line to the USB PHYs (just like on Meson8b).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:13:36 -08:00
Martin Blumenstingl
e3087187e5 ARM: dts: meson8: add the reset controller
Meson8 uses the same reset controller as Meson8b. Add the node along
with the #include for the reset lines to meson8.dtsi so we can use it
from there as well.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:13:36 -08:00
Martin Blumenstingl
a2730ed3e0 ARM: dts: meson8b: grow the reset controller memory zone
The reset controller in the Meson8b SoCs also supports level resets.
These use the same defines (from
dt-bindings/reset/amlogic,meson8b-reset.h) as the reset pulses.

The reset-meson driver internally handles the difference if a consumer
requests a reset pulse or a level reset. However, for this to work we
must extend the memory zone of the reset controller.

Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:13:36 -08:00
Yixun Lan
77f5cdbd78 ARM64: dts: meson: uart: fix address space range
The address space range is actually 0x18, fixed here.

Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:13:04 -08:00
Jerome Brunet
2363ec931e ARM64: dts: meson-gxl: add internal ethernet PHY irq
Add the interrupt of the internal ethernet PHY

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-12 14:13:04 -08:00
Hans de Goede
d82e233cee Revert "extcon: axp288: Redo charger type detection a couple of seconds after probe()"
Redoing the charger type detection to give the usb-role-switch code time
to properly set the role-switch is no good for mainline, since the
usb-role-switch code is not yet in mainline (my bad, sorry).

Also once we've that code there are better ways to fix this which are
not prone to racing as doing a retry after 2 seconds is.

This reverts commit 50082c17bb1455acacd376ae30dff92f2e1addbd.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
2018-02-13 06:49:44 +09:00
Hans de Goede
5b4e64beb6 extcon: axp288: Constify the axp288_pwr_up_down_info array
Make the axp288_pwr_up_down_info array const char * const, this leads
to the following section size changes:

.text     0x674 -> 0x664
.data     0x148 -> 0x0f0
.rodata   0x0b4 -> 0x114

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
2018-02-13 06:49:44 +09:00
Tejun Heo
685469e5bf percpu: add Dennis Zhou as a percpu co-maintainer
Dennis rewrote the percpu area allocator some months ago, understands
most of the code base and has been responsive with the bug reports and
questions.  Let's add him as a co-maintainer.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Christopher Lameter <cl@linux.com>
2018-02-12 13:08:53 -08:00
Roland Dreier
0a34e4668c nvme: Don't use a stack buffer for keep-alive command
In nvme_keep_alive() we pass a request with a pointer to an NVMe command on
the stack into blk_execute_rq_nowait().  However, the block layer doesn't
guarantee that the request is fully queued before blk_execute_rq_nowait()
returns.  If not, and the request is queued after nvme_keep_alive() returns,
then we'll end up using stack memory that might have been overwritten to
form the NVMe command we pass to hardware.

Fix this by keeping a special command struct in the nvme_ctrl struct right
next to the delayed work struct used for keep-alives.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
2018-02-12 22:18:14 +02:00
Alexander Duyck
a0073a4b8b i40e/i40evf: Add support for new mechanism of updating adaptive ITR
This patch replaces the existing mechanism for determining the correct
value to program for adaptive ITR with yet another new and more
complicated approach.

The basic idea from a 30K foot view is that this new approach will push the
Rx interrupt moderation up so that by default it starts in low latency and
is gradually pushed up into a higher latency setup as long as doing so
increases the number of packets processed, if the number of packets drops
to 4 to 1 per packet we will reset and just base our ITR on the size of the
packets being received. For Tx we leave it floating at a high interrupt
delay and do not pull it down unless we start processing more than 112
packets per interrupt. If we start exceeding that we will cut our interrupt
rates in half until we are back below 112.

The side effect of these patches are that we will be processing more
packets per interrupt. This is both a good and a bad thing as it means we
will not be blocking processing in the case of things like pktgen and XDP,
but we will also be consuming a bit more CPU in the cases of things such as
network throughput tests using netperf.

One delta from this versus the ixgbe version of the changes is that I have
made the interrupt moderation a bit more aggressive when we are in bulk
mode by moving our "goldilocks zone" up from 48 to 96 to 56 to 112. The
main motivation behind moving this is to address the fact that we need to
update less frequently, and have more fine grained control due to the
separate Tx and Rx ITR times.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-02-12 11:50:10 -08:00
Pavel Machek
6204f03d3f leds: Clarify supported chips by LM355x driver
Clarify which controllers are supported by which driver.

Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
2018-02-12 20:49:38 +01:00
Vadim Pasternak
8f886de18a leds: leds-mlxcpld: Allow compilation for 32 bit arch
It makes leds-mlxcpld available for 32 bit architecture.

Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
2018-02-12 20:49:09 +01:00
Alexander Duyck
556fdfd6e6 i40e/i40evf: Split container ITR into current_itr and target_itr
This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.

The first value current_itr represents the current value of the register.

The second value target_itr represents the desired value of the register.

The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-02-12 11:43:50 -08:00
Jan Glauber
07a2e1cf39 net: cavium: fix NULL pointer dereference in cavium_ptp_put
Prevent a kernel panic on reboot if ptp_clock is NULL by checking
the ptp pointer before using it.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Fixes: 8c56df372b ("net: add support for Cavium PTP coprocessor")
Cc: Radoslaw Biernacki <rad@semihalf.com>
Cc: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-12 14:38:37 -05:00
Alexander Duyck
d4942d581a i40evf: Correctly populate rxitr_idx and txitr_idx
While testing code for the recent ITR changes I found that updating the Tx
ITR appeared to have no effect with everything defaulting to the Rx ITR. A
bit of digging narrowed it down the fact that we were asking the PF to
associate all causes with ITR 0 as we weren't populating the itr_idx values
for either Rx or Tx.

To correct it I have added the configuration for these values to this
patch. In addition I did some minor clean-up to just add a local pointer
for the vector map instead of dereferencing it based off of the index
repeatedly. In my opinion this makes the resultant code a bit more readable
and saves us a few characters.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-02-12 11:33:46 -08:00
Alexander Duyck
92418fb147 i40e/i40evf: Use usec value instead of reg value for ITR defines
Instead of using the register value for the defines when setting up the
ring ITR we can just use the actual values and avoid the use of shifts and
macros to translate between the values we have and the values we want.

This helps to make the code more readable as we can quickly translate from
one value to the other.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-02-12 11:29:47 -08:00
Denys Vlasenko
9b2c45d479 net: make getname() functions return length rather than use int* parameter
Changes since v1:
Added changes in these files:
    drivers/infiniband/hw/usnic/usnic_transport.c
    drivers/staging/lustre/lnet/lnet/lib-socket.c
    drivers/target/iscsi/iscsi_target_login.c
    drivers/vhost/net.c
    fs/dlm/lowcomms.c
    fs/ocfs2/cluster/tcp.c
    security/tomoyo/network.c

Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.

"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.

None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.

This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.

Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.

rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.

Userspace API is not changed.

    text    data     bss      dec     hex filename
30108430 2633624  873672 33615726 200ef6e vmlinux.before.o
30108109 2633612  873672 33615393 200ee21 vmlinux.o

Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-12 14:15:04 -05:00
Sarangdhar Joshi
dcb57ed43d remoteproc: qcom: Register segments for core dump
Register MDT segments with the remoteproc core dump functionality in
order to include them in a core dump, in case of a recovery of the remote
processor.

Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 11:05:46 -08:00
Bjorn Andersson
4dd27f544c soc: qcom: mdt-loader: Return relocation base
In order to implement support for grabbing core dumps in remoteproc it's
necessary to know the relocated base of the image, as the offsets from
the virtual memory base might not be based on the physical address.

Return the adjusted physical base address to the caller.

Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2018-02-12 11:05:38 -08:00