The eFuse size is defined in property <reg> before, but the length
of registers is not equal to the size on some platforms, so we
add a new property to redefine it.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The efuse on UniPhier allows 8bit access according to the specification.
Since bit offset of nvmem is limited to 0-7, it is desiable to change
access unit of nvmem to 8bit.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the caller doesn't set stride and/or word_size in struct nvmem_config
then nvmem_register accepts this but we may face strange effects later
due to both values being 0. Therefore use 1 as default for both values.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to reinvent the wheel, we have bus_find_device_by_name().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit enhances the scan results to report the per chain signal
strength based on the latest BSS update. This provides similar
information to what is already available through STA information.
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only part of atmel_spi_remove which needs to be atomic is hardware
reset.
atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.
So the call of these functions can't be inside a spin_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regmap code looks redudant. So simplify it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since this i2smode also includes the setting of Network mode, it
should have it in the name. This patch also adds its MASK define.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name fsl_ssi_rxtx_reg_val is too long to read comfortably.
So this patch shortens it by using an array (fsl_ssi_regvals,
renamed from fsl_ssi_reg_val). To do that, it also introduces
two macros (TX and RX) to replace the wrapper structure. This
will also help further cleanups.
Meanwhile, it unifies all local variable with the name "vals"
to get rid of the name "reg" -- could be confusing with "regs"
in the private struct for regmap.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the variable name. This reduces one over-80-character line.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shortens the variable name to save space, useful for dev_err outputs.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patches unifies the error message in the "failed to xxxx" format.
It also reduces the length of one line and adds spaces to an operator.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch just simply unifies the coding style.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames CCSR_SSI_xxx to REG_SSI_xxx and SSI_xxx_yyy style.
It also slightly reduces the length of them to save some space.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refines the comments by:
1) Removing all out-of-date comments
2) Removing all not-so-useful comments
3) Unifying the styles of all comments
4) Shortening comments to be more conise
5) Adding comments to improve code readablity
6) Moving all register related comments to fsl_ssi.h
7) Adding comments to all register and field defines
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There should be no trouble to understand dev = pdev->dev.
This can save some space to have more print info or save
some wrapped lines.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shorten the private data structure to save some wrapped lines.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, calls into each file are used to register the various
platform drivers. Change this to a table of pointers to platform_driver
structs to allow using platform_register_drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Having the filename in the header serves little purpose and is
often wrong after renames as it is here in several places, just
drop it from all omapdrm files.
While we are here unify the copyright tags to the TI recommended style.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This patch adds tpu groups and function to r8a7745/r8a7794.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds PFC PWM[0123456] pin groups and functions, enabling
PWM on the r8a7794 and r8a7745.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Send disconnection reason code to user space even if it's locally
generated, since some tests that check reason code may fail because of
the current behavior.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function binder_alloc_new_buf_locked() is only used in this file, so
make it static. Also clean up sparse warning:
drivers/android/binder_alloc.c:330:23: warning: no previous prototype
for ‘binder_alloc_new_buf_locked’ [-Wmissing-prototypes]
In addition, the line of the function name exceeds 80 characters when
add static for this function, hence indent its arguments anew.
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e937b8da5a.
Turns out that a new driver (mt76) is coming in through
Kalle's tree, and will conflict with this. It also has some
conflicting requirements, so we'll revisit this later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit b0d52ad821.
We need to revert the TXQ scheduling API due to conflicts
with a new driver, and this depends on that API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Trivial fix to spelling mistake in dev_dbg debug message. Also
add in a missing comma.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CoreSight TPIU should be disabled when tracing to other sinks to allow
them to operate at full bandwidth.
This patch fixes tpiu_disable_hw() to correctly disable the TPIU by
configuring the TPIU to stop on flush, initiating a manual flush, waiting
for the flush to complete and then waits for the TPIU to indicate it has
stopped.
Signed-off-by: Robert Walker <robert.walker@arm.com>
Tested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ptr_ret.cocci warnings:
drivers/hwtracing/coresight/coresight-tpiu.c:163:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-funnel.c:217:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-dynamic-replicator.c:166:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to reinvent the wheel, we have bus_find_device_by_name().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case that CONFIG_SLUB_DEBUG is on and pty is used, races between
release_one_tty and flush_to_ldisc work threads may happen and lead
to use-after-free condition on tty->link->port. Because SLUB_DEBUG
is turned on, freed tty->link->port is filled with POISON_FREE value.
So far without SLUB_DEBUG, port was filled with zero and flush_to_ldisc
could return without a problem by checking if tty is NULL.
CPU 0 CPU 1
----- -----
release_tty pty_write
cancel_work_sync(tty) to = tty->link
tty_kref_put(tty->link) tty_schedule_flip(to->port)
<< workqueue >> ...
release_one_tty ...
pty_cleanup ...
kfree(tty->link->port) << workqueue >>
flush_to_ldisc
tty = READ_ONCE(port->itty)
tty is 0x6b6b6b6b6b6b6b6b
!!PANIC!! access tty->ldisc
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b6b93
pgd = ffffffc0eb1c3000
[6b6b6b6b6b6b6b93] *pgd=0000000000000000, *pud=0000000000000000
------------[ cut here ]------------
Kernel BUG at ffffff800851154c [verbose debug info unavailable]
Internal error: Oops - BUG: 96000004 [#1] PREEMPT SMP
CPU: 3 PID: 265 Comm: kworker/u8:9 Tainted: G W 3.18.31-g0a58eeb #1
Hardware name: Qualcomm Technologies, Inc. MSM 8996pro v1.1 + PMI8996 Carbide (DT)
Workqueue: events_unbound flush_to_ldisc
task: ffffffc0ed610ec0 ti: ffffffc0ed624000 task.ti: ffffffc0ed624000
PC is at ldsem_down_read_trylock+0x0/0x4c
LR is at tty_ldisc_ref+0x24/0x4c
pc : [<ffffff800851154c>] lr : [<ffffff800850f6c0>] pstate: 80400145
sp : ffffffc0ed627cd0
x29: ffffffc0ed627cd0 x28: 0000000000000000
x27: ffffff8009e05000 x26: ffffffc0d382cfa0
x25: 0000000000000000 x24: ffffff800a012f08
x23: 0000000000000000 x22: ffffffc0703fbc88
x21: 6b6b6b6b6b6b6b6b x20: 6b6b6b6b6b6b6b93
x19: 0000000000000000 x18: 0000000000000001
x17: 00e80000f80d6f53 x16: 0000000000000001
x15: 0000007f7d826fff x14: 00000000000000a0
x13: 0000000000000000 x12: 0000000000000109
x11: 0000000000000000 x10: 0000000000000000
x9 : ffffffc0ed624000 x8 : ffffffc0ed611580
x7 : 0000000000000000 x6 : ffffff800a42e000
x5 : 00000000000003fc x4 : 0000000003bd1201
x3 : 0000000000000001 x2 : 0000000000000001
x1 : ffffff800851004c x0 : 6b6b6b6b6b6b6b93
Signed-off-by: Sahara <keun-o.park@darkmatter.ae>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 4c7f16d14a ("drm/sun4i: Fix TCON clock and regmap
initialization sequence") moved a bunch of logic around, but forgot to
update the gotos after the introduction of the err_free_dotclock label.
It means that if we fail later that the one introduced in that commit,
we'll just to the old label which isn't free the clock we created. This
will result in a breakage as soon as someone tries to do something with
that clock, since its resources will have been long reclaimed.
Cc: <stable@vger.kernel.org>
Fixes: 4c7f16d14a ("drm/sun4i: Fix TCON clock and regmap initialization sequence")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f83c1cebc731f0b4251f5ddd7b38c718cd79bb0b.1512662253.git-series.maxime.ripard@free-electrons.com
Prior to this patch, the code would happily trigger TX on some ports
before having a chance of reading the RX buffer from the rest of them.
When no flow control was used, this led to RX buffer overruns and
therefore lost data under certain circumstances.
I was able to reproduce this with MAX14830 (that's a quad channel one)
and a simple daisy-chain of RX and TX ports on the eval board:
- TX0 -> RX1
- TX1 -> RX2
- TX2 -> RX3
- TX3 -> RX0
I was testing this by transferring 2MB of data at 115200 baud via each
port. I used a Solidrun Clearfog Base (Armada 388) which was talking to
the UART over an SPI bus clocked at 26MHz (the chip's maximum). Without
this patch, I would always get a "Possible RX FIFO overrun" in dmesg,
and fewer-than-expected amount of bytes received over ttyMAX0. Results
on ttyMAX{1,2,3} tended to be correct all the time, even without the
previous patches in this series and with PIO SPI transfers ("indirect
mode" as the Marvell datasheet calls it), so I assume that heavy
congestion is needed in order to reproduce this.
A drawback of this patch is that the throughput gets reduced "a bit".
Previously, a 115200 baud resulted in about 11.2kBps throughput as
reported by a simple `pv`. With this patch, the throughput of four
parallel streams is roughly 7kBps each, and 9kBps for three streams.
There is no slowdown for one or two parallel streams.
Situation is worse if bytes are being read one-by-one (such as if the
userspace wants to perform parity/framing/break checking) and therefore
without the batched reads.
With just this patch and no other modifications on top of 4.14, I was
only getting roughly 3.6kBps with four parallel streams. The
single-stream performance was the same, and I was seeing about 7.2kBps
with two parallel streams. `perf top` said that a substantial amount of
time was spent in `finish_task_switch`, `_raw_spin_unlock_irqrestore`
and `__timer_delay`.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware has a 128 byte RX FIFO buffer for each independent UART.
Previously, the code was always reading that byte-by-byte via
independent SPI transactions and the associated overhead. In practice,
this led to up to eight bytes over SPI for just one byte in the UART's
RX FIFO:
- reading the global IRQ register (two bytes, one for command, the other
for data)
- reading one UART's ISR (again two bytes)
- reading the byte count (two bytes yet again)
- finally, reading one byte of the FIFO via another two-byte transaction
We cannot always use a batched read. If the TTY is set to intercept
break conditions or report framing or parity errors, then it is required
to check the Line Status Register (LSR) for each byte which is read from
the RX FIFO. The documentation does not show a way of doing that in a
single SPI transaction; registers 0x00 and 0x04 are separate.
In my testing, this is no silver bullet. I was feeding 2MB of random
data over four daisy-chaned UARTs of MAX14830, and this is the
distribution that I was getting:
- R <= 1: 7437322
- R <= 2: 162093
- R <= 4: 4093
- R <= 8: 4196
- R <= 16: 645
- R <= 32: 165
- R <= 64: 58
- R <= 128: 0
For a reference, batching the write operations works much better:
- W <= 1: 2664
- W <= 2: 1305
- W <= 4: 627
- W <= 8: 371
- W <= 16: 121
- W <= 32: 68
- W <= 64: 33
- W <= 128: 63139
That's probably because this HW/SW combination (Clearfog Base, Armada
388) is probably "good enough" to react to the chip's IRQ "fast enough"
most of the time. Still, I was getting RX overruns every now and then.
In future, I plan to improve this by letting the RX FIFO be filled a
little more (the chip has support for that and also for a "stale
timeout" to prevent additional starvation).
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmit register supports batched writes. The key is simply to keep
sending additional bytes up to the FIFO size in the same SPI
transaction with the CS pin still being held low.
This duplicates the regmap infrastructure to a certain extent. There are
some provisions for multiple writes in there, but there does not appear
to be any support for those writes which are destined to the *same*
register (and also no standard for SPI bus transfers of these, anyway).
This patch does not solve every case (if the UART xmit circular buffer
wraps around, we're still doing two SPI transactions), but at least
it's not one-byte-per-transaction anymore.
This change does not touch the receive path at this time. Doing that in
the generic case appears to be impossible in the general case, because
the chips' status register contains data about the *current* byte in the
HW's Rx FIFO. We cannot read these two registers in one go,
unfortunately.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a kernel newcomer, I got bitten by lack of examples on this front. I
had troubles figuring out where these clocks could be defined ("/clocks"
is where the generic infrastructure expects them).
One should also ensure that a unique name is used. Generic names such as
"osc" tend to be already used by some board-wide clock crystals.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to my chip's datasheet [1], the IRQ output is an open
collector pin which is suitable for sharing with other chips. The chip
also has a register which indicates which UART performed a change and
the driver checks that register already, so we have everything what is
needed to effectively share the IRQ GPIO.
[1] https://datasheets.maximintegrated.com/en/ds/MAX14830.pdf
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was getting this trace along with a disabled IRQ when I was generating
heavy traffic over four daisy-chained UARTs (MAX14830) on my test kit
(Marvell Armada AM388, Solidrun Clearfog Base):
irq 51: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 68 Comm: irq/51-spi1.2 Not tainted 4.14.4 #7
Hardware name: Marvell Armada 380/385 (Device Tree)
[<c0110ba4>] (unwind_backtrace) from [<c010c1d8>] (show_stack+0x10/0x14)
[<c010c1d8>] (show_stack) from [<c07776ac>] (dump_stack+0x84/0x98)
[<c07776ac>] (dump_stack) from [<c016bdfc>] (__report_bad_irq+0x28/0xcc)
[<c016bdfc>] (__report_bad_irq) from [<c016c204>] (note_interrupt+0x28c/0x2dc)
[<c016c204>] (note_interrupt) from [<c01695d4>] (handle_irq_event_percpu+0x4c/0x58)
[<c01695d4>] (handle_irq_event_percpu) from [<c0169624>] (handle_irq_event+0x44/0x68)
[<c0169624>] (handle_irq_event) from [<c016ce80>] (handle_edge_irq+0x12c/0x1dc)
[<c016ce80>] (handle_edge_irq) from [<c016872c>] (generic_handle_irq+0x24/0x34)
[<c016872c>] (generic_handle_irq) from [<c03fc5a0>] (mvebu_gpio_irq_handler+0xe0/0x184)
[<c03fc5a0>] (mvebu_gpio_irq_handler) from [<c016872c>] (generic_handle_irq+0x24/0x34)
[<c016872c>] (generic_handle_irq) from [<c0168c4c>] (__handle_domain_irq+0x5c/0xb4)
[<c0168c4c>] (__handle_domain_irq) from [<c0101520>] (gic_handle_irq+0x4c/0x90)
[<c0101520>] (gic_handle_irq) from [<c010ce4c>] (__irq_svc+0x6c/0x90)
Exception stack(0xeea77c30 to 0xeea77c78)
7c20: 0000000a 018cba80 0000000a f098f680
7c40: 0000020a f098f680 00000008 0000020a 018cba80 00000001 ee9302a0 eea76000
7c60: ef2b2640 eea77c80 c050687c c0506894 80070013 ffffffff
[<c010ce4c>] (__irq_svc) from [<c0506894>] (orion_spi_setup_transfer+0x118/0x20c)
[<c0506894>] (orion_spi_setup_transfer) from [<c05069ac>] (orion_spi_transfer_one+0x1c/0x26c)
[<c05069ac>] (orion_spi_transfer_one) from [<c05060e4>] (spi_transfer_one_message+0xec/0x500)
[<c05060e4>] (spi_transfer_one_message) from [<c05059a4>] (__spi_pump_messages+0x3f4/0x680)
[<c05059a4>] (__spi_pump_messages) from [<c0505e38>] (__spi_sync+0x1fc/0x200)
[<c0505e38>] (__spi_sync) from [<c0505e60>] (spi_sync+0x24/0x3c)
[<c0505e60>] (spi_sync) from [<c0505f48>] (spi_write_then_read+0xd0/0x17c)
[<c0505f48>] (spi_write_then_read) from [<c0482efc>] (_regmap_raw_read+0xb0/0x250)
[<c0482efc>] (_regmap_raw_read) from [<c04830c0>] (_regmap_bus_read+0x24/0x4c)
[<c04830c0>] (_regmap_bus_read) from [<c04826f4>] (_regmap_read+0x60/0x148)
[<c04826f4>] (_regmap_read) from [<c0482818>] (regmap_read+0x3c/0x5c)
[<c0482818>] (regmap_read) from [<c04592b4>] (max310x_port_irq+0x104/0x2dc)
[<c04592b4>] (max310x_port_irq) from [<c0459a40>] (max310x_ist+0x68/0xc0)
[<c0459a40>] (max310x_ist) from [<c016a610>] (irq_thread_fn+0x1c/0x54)
[<c016a610>] (irq_thread_fn) from [<c016a8d8>] (irq_thread+0x12c/0x1f0)
[<c016a8d8>] (irq_thread) from [<c013e560>] (kthread+0x128/0x158)
[<c013e560>] (kthread) from [<c0107a50>] (ret_from_fork+0x14/0x24)
handlers:
[<c0169694>] irq_default_primary_handler threaded [<c04599d8>] max310x_ist
Disabling IRQ #51
On a multi-UART max310x, each UART has its own interrupt status register
which automatically de-asserts the IRQ line upon read. (There are also
top-level IRQ indicator registers which are not clear-on-read, but they
are not relevant here.) It was quite possible to receive a pending IRQ
for, e.g., UART0, enter the threaded IRQ handler, clear the ISR for
UART0 which de-asserts the IRQ line, and then race with another event on
the same chip, but a different UART channel. That resulted in another
edge on the shared-within-the-chip IRQ line which got intercepted by the
kernel.
That all led to an edge-level interrupt which was not being handled by
anybody because our threaded handler hasn't finished yet. As the chip
actually uses *level* triggered IRQs, let's convert the example DT
bindings to these.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by Russell King, a driver should not really care about bits
such as the interrupt polarity or whether it is edge- or level-
triggered. The reasons for that include:
- an upstream IRQ controller which cannot support edge- or
level-triggered interrupts,
- board design with a built-in inverter
The interrupt type is being already specified by the Device Tree,
anyway. Other drivers (gpio/gpio-tc3589x.c for example) already work in
this way, delegating the proper IRQ line setup to the DT and not
specifying anything by hand.
Also, there's no reason to have the IRQ flags split between two places.
The SPI probing is the only entry point anyway.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we added the regulator support in commit 90c5d7cdae ("ARM: dts:
sun8i: a711: Add regulator support"), we also dropped the PMIC's
compatible. Since it's not in the PMIC DTSI, unlike most other PMIC
DTSI, it obviously wasn't probing anymore.
Re-add it so that everything works again.
Fixes: 90c5d7cdae ("ARM: dts: sun8i: a711: Add regulator support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
meson_mx_efuse_read calculates the address internal to the eFuse based
on the offset and the word size. This works fine with any given offset.
However, the offset is also included when writing to the output buffer.
This means that reading 4 bytes at offset 500 tries to write beyond the
array allocated by the nvmem core as it wants to write the 4 bytes to
"buffer address + offset (500)".
This issue did not show up in the previous tests since no driver uses
any value from the eFuse yet and reading the eFuse via sysfs simply
reads the whole eFuse, starting at offset 0.
Fix this by only including the offset in the internal address
calculation.
Fixes: 8caef1fa91 ("nvmem: add a driver for the Amlogic Meson6/Meson8/Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a missing ethernet 0 alisas in the devicetree on the
Nanopi M1 Plus.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Nanopi M1.
It uses the internal PHY
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Check the status of the DMM engine after it is reported that the
transaction was completed as in rare cases the engine might not reached a
working state.
The wait_status() will print information in case the DMM is not reached the
expected state and the dmm_txn_commit() will return with an error code to
make sure that we are not continuing with a broken setup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To help diagnose DMM errors, print out information if any of the error bits
are set in the interrupt status register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the wait_status() fails either because of an error reported in the
STATUS register or because of a timeout waiting for the wait_mask, print
information which might help diagnose the reason.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The error bit definitions are typoed in DMM_IRQSTAT_ERR_MASK which went
unnoticed since the DMM_IRQSTAT_ERR_MASK was not used.
Change the bit definitions to the correct ones.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The number of function declarations in the omap_drv.h degrades
readability. To fix it, create new header files for each part of the
driver and move the related functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The venc_probe_of() function has an error cleanup path that returns
success instead of an error code. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>