Fix various sync state issues causing racy/bogus sync ratio,
sync_action ad health chars in dm_status() info output.
Sync ratio could be N/N (i.e. 100%) shortly after raid set
creation, i.e. creating a new RaidLV or upconverting a linear LV to
raid1 thus:
"0 2097152 raid raid1 2 Aa 2097162/2097152 recover 0 0 -"
instead of:
"0 2097152 raid raid1 2 Aa 0/2097152 idle 0 0 -"
Sync action could be non-idle, when the MD thread was done with io.
Health chars could be 'A' when they should be 'a' for a short time
before a resynchonization started.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The raid_status() function passes the bool array_in_sync variable around
providing synchronization state of the MD array. Replace it with a
runtime flag. This will avoid a pattern of having to pass discrete
variables to various functions.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The MD sync thread updates recovery flags providing state of any
running, idle, frozen, recovering, reshaping, ... activity it performs
and updates respective flags asynchronously versus dm processing
raid_status(). To close that race window, take a single copy of the
flags and pass it into its callees.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
During a reshape request: if userspace reloads a "raid" table multiple
times, resulting in multiple superblock reads, the raid set needs to
stay frozen until all config changes (chunk size, layout data_offset,
delta_disks) have been stored in the superblocks and respective flags
cleared.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Check all component data device sizes versus calculated size.
Reject if device(s) are too small. Otherwise, MD will fail the
operation by accessing beyond the end of the data device.
An example use-case is that growing bitmap won't fit any more and the MD
runtime will report an error when DM raid should catch this earlier.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The raid set size is being revalidated unconditionally before a
reshaping conversion is started. MD requires the size to only be
reduced in case of a stripe removing (i.e. shrinking) reshape but not
when growing because the raid array has to stay small until after the
growing reshape finishes.
Fix by avoiding the size revalidation in preresume unless a shrinking
reshape is requested.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pay attention to existing reshape space to define if a raid set needs
resizing. Otherwise we can hit "Can't resize a reshaping raid set"
when a reshape is being requested.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The md raid personalities call md_finish_reshape() at the end of a
reshape conversion which adjusts rdev->sectors.
Correct/check rdev->sectors before initiating a reshape and raise the
recovery pointer accordingly.
Otherwise, the DM raid coordinated reshape will fail.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
md_stop_writes() is called in raid_presuspend() causing deadlocks on
bios submitted afterwards -- which happens on loaded raid sets with
conversion requests.
Fix by moving md_stop_writes() to raid_postsuspend(). NOTE: when the
recovery's frozen (MD_RECOVERY_FROZEN), writes haven't been started (or
are already stopped) so don't stop them again.
Also remove superfluous readonly setting.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When system is under memory pressure it is observed that dm bufio
shrinker often reclaims only one buffer per scan. This change fixes
the following two issues in dm bufio shrinker that cause this behavior:
1. ((nr_to_scan - freed) <= retain_target) condition is used to
terminate slab scan process. This assumes that nr_to_scan is equal
to the LRU size, which might not be correct because do_shrink_slab()
in vmscan.c calculates nr_to_scan using multiple inputs.
As a result when nr_to_scan is less than retain_target (64) the scan
will terminate after the first iteration, effectively reclaiming one
buffer per scan and making scans very inefficient. This hurts vmscan
performance especially because mutex is acquired/released every time
dm_bufio_shrink_scan() is called.
New implementation uses ((LRU size - freed) <= retain_target)
condition for scan termination. LRU size can be safely determined
inside __scan() because this function is called after dm_bufio_lock().
2. do_shrink_slab() uses value returned by dm_bufio_shrink_count() to
determine number of freeable objects in the slab. However dm_bufio
always retains retain_target buffers in its LRU and will terminate
a scan when this mark is reached. Therefore returning the entire LRU size
from dm_bufio_shrink_count() is misleading because that does not
represent the number of freeable objects that slab will reclaim during
a scan. Returning (LRU size - retain_target) better represents the
number of freeable objects in the slab. This way do_shrink_slab()
returns 0 when (LRU size < retain_target) and vmscan will not try to
scan this shrinker avoiding scans that will not reclaim any memory.
Test: tested using Android device running
<AOSP>/system/extras/alloc-stress that generates memory pressure
and causes intensive shrinker scans
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit ca5beb76 ("dm mpath: micro-optimize the hot path relative to
MPATHF_QUEUE_IF_NO_PATH") caused bio-based DM-multipath to fail mptest's
"test_02_sdev_delete".
Restoring the logic that existed prior to commit ca5beb76 fixes this
bio-based DM-multipath regression. Also verified all mptest tests pass
with request-based DM-multipath.
This commit effectively reverts commit ca5beb76 -- but it does so
without reintroducing the need to take the m->lock spinlock in
must_push_back_{rq,bio}.
Fixes: ca5beb76 ("dm mpath: micro-optimize the hot path relative to MPATHF_QUEUE_IF_NO_PATH")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2017-12-07
The following pull-request contains BPF updates for your net-next tree.
The main changes are:
1) Detailed documentation of BPF development process from Daniel.
2) Addition of is_fullsock, snd_cwnd and srtt_us fields to bpf_sock_ops
from Lawrence.
3) Minor follow up for bpf_skb_set_tunnel_key() from William.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the test_pattern control and the h/vflip controls.
This makes it possible to switch to more interesting test patterns and to
test control handling in v4l-subdevs.
There are more tpg-related controls that can be added, but this is a good
start.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix small whitespace checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Private destructor could be called when register_netdev() fail with
rtnl lock held. This will lead deadlock in tun_free_netdev() who tries
to hold rtnl_lock. Fixing this by switching to use spinlock to
synchronize.
Fixes: 96f8406162 ("tun: add eBPF based queue selection method")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes intermittent soft reboot issue with firmware load
increases wait time of reset, as required by HW
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When used as part of a display pipeline, the VSP is stopped and
restarted explicitly by the DU from its suspend and resume handlers.
There is thus no need to stop or restart pipelines in the VSP suspend
and resume handlers, and doing so would cause the hardware to be
left in a misconfigured state.
Ensure that the VSP suspend and resume handlers do not affect DRM-based
pipelines.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's not clear if the transmit status that is printed when debugging
is enabled is hex or decimal. Add 0x prefix to make this explicit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 'return' was missing when detecting Arbitration Lost and
calling transmit_done. With the return transmit_done could be
called a second time, confusing the CEC framework. Luckily
the Arbitration Lost condition is very rare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is possible to call STREAMON without the minimum number of
buffers queued. In this case the vb2_queue state will be set to
streaming but the start_streaming vb2_op will not be called.
Later when enough buffers are queued, start_streaming will
be called but vb2_is_streaming will already return true.
Also removed the queue state check in stop_streaming since it's
not valid there either.
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Reviewed-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This change fixes the calculation of B-frames and GOP size by
adopt v4l2 controls with the firmware interface expectations.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fixed two small checkpatch comments]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the visorbus driver out of staging (drivers/staging/unisys/visorbus)
and to drivers/visorbus. Modify the configuration and makefiles so they
now reference the new location. The s-Par header file visorbus.h that is
referenced by all s-Par drivers, is being moved into include/linux.
Signed-off-by: David Kershner <david.kershner@unisys.com>
Reviewed-by: Tim Sell <timothy.sell@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking of modulation in rf69_set_modulation_shaping is done by
if-else and since else part covers OOK and UNDEF values it possible to
set modulation shaping for undefined modulation type.
To fix this validation should be done by switch clause and in case of
undefined modulation error returned.
Signed-off-by: Marcin Ciupak <marcin.s.ciupak@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that rf69_get_modulation() function will return
'undefined' value and this value is missing in enum modulation. Fix this
by adding appropriate entry in enum modulation.
Signed-off-by: Marcin Ciupak <marcin.s.ciupak@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes following warnings found by checkpatch.pl script:
WARNING: line over 80 characters
Signed-off-by: Rodrigo Zaiden <rodrigoffzz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to set_flow_mode() was supposed to be on the next line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note that the inputs for the Composite and S-Video are inverted in
regard to most of the other boards using a cx231xx chip.
Signed-off-by: Romain Reignier <r.reignier@robopec.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Some comments, like "without memcpy would be nice", are removed.
Other comments are just translated to english.
rf69.c is now plain ASCII.
Signed-off-by: Simon Sandström <simon@nikanor.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aligning the Tx buffers at 64B is a performance optimization
recommendation, not a hard requirement.
Make optional the alignment of Tx FD buffers, without enforcing
a reallocation in case there is not enough headroom for it.
On Rx, we keep allocating buffers with enough headroom to allow
Tx alignment of forwarded frames.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For non-linear skbs we build scatter-gather frames and allocate
a new buffer for the S/G table in which we reserve the required
headroom, so the actual skb headroom size doesn't matter.
Rather than use a one-size-fits-all approach, decide when to
enforce headroom requirements on a frame by frame basis.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Tx confirmed frames that have an error indication in the frame
descriptor, we look at the Frame Annotation Status field (in the
buffer headroom) for details on the root cause and then print
a debug message with that information.
While useful in initial development stages, it doesn't bring
enough added value to justify reserving 64B of headroom for all
Tx frames (FAS is only 8B long, but we must reserve chunks of 64B
from the hardware annotation area).
If we remove the need for FAS field from egress frames, we can
renounce hardware annotation completely, since FAS is the only
HWA field we currently use.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a counter for the number of egress frames that need to be
realloc'ed due to insufficient headroom space.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4b2d9fe879 ("staging: fsl-dpaa2/eth: Extra headroom in RX
buffers") tried to avoid the performance penalty of doing skb
reallocations in the network stack for IP forwarded frames between
two DPAA2 Ethernet interfaces. This led to a (too) complicated
formula that relies on the stack's internal implementation.
Instead, it's safer and easier to just not request any guarantee
from the stack. We already double check in the driver the required
headroom size of egress frames and realloc the skb if needed, so
we don't need to add any extra code.
On forwarding between two of our own interfaces, there is no
functional change; for traffic forwarded from a different device or
generated on the core, skb realloc operations are moved from the stack
to our driver, with no visible impact on performance.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4b2d9fe879 ("staging: fsl-dpaa2/eth: Extra headroom in RX
buffers") removes the software annotation (SWA) area from the RX
buffer layout, as it's not used by anyone, but fails to update the
macros for accessing hardware annotation (HWA) fields, which is
right after the SWA in the buffer headroom.
This may lead to some frame annotation status fields (e.g. indication
if L3/L4 checksum is valid) to be read incorrectly.
Turn the accessor macros into inline functions and add a bool param
to specify if SWA is present or not.
Fixes: 4b2d9fe879 ("staging: fsl-dpaa2/eth: Extra headroom in RX buffers")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it more clear that nodes without "__overlay__" subnodes are
skipped, by reverting the logic and using continue.
This also reduces indentation level.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
If an overlay has no "__symbols__" node, but it has nodes without
"__overlay__" subnodes at the end (e.g. a "__fixups__" node), after
filling in all fragments for nodes with "__overlay__" subnodes,
"fragment = &fragments[cnt]" will point beyond the end of the allocated
array.
Hence writing to "fragment->overlay" will overwrite unallocated memory,
which may lead to a crash later.
Fix this by deferring both the assignment to "fragment" and the
offending write afterwards until we know for sure the node has an
"__overlay__" subnode, and thus a valid entry in "fragments[]".
Fixes: 61b4de4e0b ("of: overlay: minor restructuring")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
The macro calls its argument -a function- twice, makes the calling
function return prematurely -skipping resource cleanup code- and hurts
understandability.
Signed-off-by: Nguyen Phan Quang Minh <minhnpq16@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
->pkey_algo used to be an enum, but was changed to a string by commit
4e8ae72a75 ("X.509: Make algo identifiers text instead of enum"). But
two comparisons were not updated. Fix them to use strcmp().
This bug broke signature verification in certain configurations,
depending on whether the string constants were deduplicated or not.
Fixes: 4e8ae72a75 ("X.509: Make algo identifiers text instead of enum")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
keyctl_restrict_keyring() allows through a NULL restriction when the
"type" is non-NULL, which causes a NULL pointer dereference in
asymmetric_lookup_restriction() when it calls strcmp() on the
restriction string.
But no key types actually use a "NULL restriction" to mean anything, so
update keyctl_restrict_keyring() to reject it with EINVAL.
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 97d3aa0f31 ("KEYS: Add a lookup_restriction function for the asymmetric key type")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Variable key_ref is being assigned a value that is never read;
key_ref is being re-assigned a few statements later. Hence this
assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Use crypto_shash_digest() instead of crypto_shash_init() followed by
crypto_shash_finup(). (For simplicity only; they are equivalent.)
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
In public_key_verify_signature(), if akcipher_request_alloc() fails, we
return -ENOMEM. But that error code was set 25 lines above, and by
accident someone could easily insert new code in between that assigns to
'ret', which would introduce a signature verification bypass. Make the
code clearer by moving the -ENOMEM down to where it is used.
Additionally, the callers of public_key_verify_signature() only consider
a negative return value to be an error. This means that if any positive
return value is accidentally introduced deeper in the call stack (e.g.
'return EBADMSG' instead of 'return -EBADMSG' somewhere in RSA),
signature verification will be bypassed. Make things more robust by
having public_key_verify_signature() warn about positive errors and
translate them into -EINVAL.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Use crypto_shash_digest() instead of crypto_shash_init() followed by
crypto_shash_finup(). (For simplicity only; they are equivalent.)
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
pkcs7_validate_trust_one() used 'x509->next == x509' to identify a
self-signed certificate. That's wrong; ->next is simply the link in the
linked list of certificates in the PKCS#7 message. It should be
checking ->signer instead. Fix it.
Fortunately this didn't actually matter because when we re-visited
'x509' on the next iteration via 'x509->signer', it was already seen and
not verified, so we returned -ENOKEY anyway.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
If pkcs7_check_authattrs() returns an error code, we should pass that
error code on, rather than using ENOMEM.
Fixes: 99db443506 ("PKCS#7: Appropriately restrict authenticated attributes and content type")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Callers of sprint_oid() do not check its return value before printing
the result. In the case where the OID is zero-length, -EBADMSG was
being returned without anything being written to the buffer, resulting
in uninitialized stack memory being printed. Fix this by writing
"(bad)" to the buffer in the cases where -EBADMSG is returned.
Fixes: 4f73175d03 ("X.509: Add utility functions to render OIDs as strings")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
In sprint_oid(), if the input buffer were to be more than 1 byte too
small for the first snprintf(), 'bufsize' would underflow, causing a
buffer overflow when printing the remainder of the OID.
Fortunately this cannot actually happen currently, because no users pass
in a buffer that can be too small for the first snprintf().
Regardless, fix it by checking the snprintf() return value correctly.
For consistency also tweak the second snprintf() check to look the same.
Fixes: 4f73175d03 ("X.509: Add utility functions to render OIDs as strings")
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Adding a specially crafted X.509 certificate whose subjectPublicKey
ASN.1 value is zero-length caused x509_extract_key_data() to set the
public key size to SIZE_MAX, as it subtracted the nonexistent BIT STRING
metadata byte. Then, x509_cert_parse() called kmemdup() with that bogus
size, triggering the WARN_ON_ONCE() in kmalloc_slab().
This appears to be harmless, but it still must be fixed since WARNs are
never supposed to be user-triggerable.
Fix it by updating x509_cert_parse() to validate that the value has a
BIT STRING metadata byte, and that the byte is 0 which indicates that
the number of bits in the bitstring is a multiple of 8.
It would be nice to handle the metadata byte in asn1_ber_decoder()
instead. But that would be tricky because in the general case a BIT
STRING could be implicitly tagged, and/or could legitimately have a
length that is not a whole number of bytes.
Here was the WARN (cleaned up slightly):
WARNING: CPU: 1 PID: 202 at mm/slab_common.c:971 kmalloc_slab+0x5d/0x70 mm/slab_common.c:971
Modules linked in:
CPU: 1 PID: 202 Comm: keyctl Tainted: G B 4.14.0-09238-g1d3b78bbc6e9 #26
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
task: ffff880033014180 task.stack: ffff8800305c8000
Call Trace:
__do_kmalloc mm/slab.c:3706 [inline]
__kmalloc_track_caller+0x22/0x2e0 mm/slab.c:3726
kmemdup+0x17/0x40 mm/util.c:118
kmemdup include/linux/string.h:414 [inline]
x509_cert_parse+0x2cb/0x620 crypto/asymmetric_keys/x509_cert_parser.c:106
x509_key_preparse+0x61/0x750 crypto/asymmetric_keys/x509_public_key.c:174
asymmetric_key_preparse+0xa4/0x150 crypto/asymmetric_keys/asymmetric_type.c:388
key_create_or_update+0x4d4/0x10a0 security/keys/key.c:850
SYSC_add_key security/keys/keyctl.c:122 [inline]
SyS_add_key+0xe8/0x290 security/keys/keyctl.c:62
entry_SYSCALL_64_fastpath+0x1f/0x96
Fixes: 42d5ec27f8 ("X.509: Add an ASN.1 decoder")
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>