... and consolidate the definition of sigframe_ia32->extramask - it's
always a 1-element array of 32bit unsigned.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This fixes a problem found on the MacBookPro 2017 Retina panel.
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec = multiplier 0xc),
but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to add the additiional 324000 kbps link rate during
edp setup.
Link to previous discussion of a different attempted fix
with Ville and Jani:
https://patchwork.kernel.org/patch/11325935/
v2: Follow Jani's proposal of defining quirk_rates[] instead
of just appending 324000. This for better clarity.
v3: Rebased onto current drm-tip, as of 16-March-2020. Adapt
to new edid_quirks parameter of drm_dp_has_quirk().
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316042340.4783-1-mario.kleiner.de@gmail.com
The .set_suspend_enable() and .set_suspend_disable() methods are not
supposed to immediately change the regulator state but just indicated
if the regulator should be enabled or disabled when standby mode is
entered (by a hardware signal).
However currently they set control the SEL bits in the DVC registers,
which causes the voltage to change to immediately between the "A"
(normal) and "B" (standby) values as programmed and does nothing for
the enable state...
This means that "regulator-on-in-suspend" does not work (the regulator
is switched off when the PMIC enters standby mode on the hardware
signal) and, potentially, depending on the A and B voltage
configurations the voltage could be incorrectly changed *before*
actually entering suspend.
The right bit to use for the functionality is the "CONF" bit in the
"CONT" register.
The detailed register description says "Sequencer target state"
for this bit which is not very clear but the functional description
is clearer.
>From 5.1.5 System Enable:
De-asserting SYS_EN (changing from active to passive state)
clears control SYSTEM_EN which triggers a power down sequence
into hibernate/standby mode
...
With the exception of supplies that have the xxxx_CONF control
bit asserted, all regulators in power domains POWER1, POWER, and
SYSTEM are sequentially disabled in reverse order.
Regulators with the <x>_CONF bit set remain on but change the
active voltage controlregisters from V<x>_A to V<x>_B
(if V<x>_B is notalready selected).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Link: https://lore.kernel.org/r/1584461691-14344-1-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Mark Brown <broonie@kernel.org>
drm_mode_config_init() may not have been called when the driver/device
doesn't support modeset. That will cause drm_mode_config_validate()
to oops. Skip the validation for !modeset.
TODO: We may want to consider calling drm_mode_config_init()
unconditionally to avoid similar issues elsewhere...
Fixes: 74d2aacbe8 ("drm: Validate encoder->possible_clones")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318182518.31618-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_hdcp.c.
This also involves extracting the drm_i915_private device from the
intel_connector type for use in the macros.
v2 by Jani:
- rebase
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/47d5e88dedc08ee48938344296ada550dedd5f90.1583766715.git.jani.nikula@intel.com
Convert various instances of printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_fbdev.c.
This also involves extracting the drm_i915_private device from various
intel types.
v2 by Jani:
- fix the final one too
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7081a49d20cc46b1b1144c83a4e21294d121d8a7.1583766715.git.jani.nikula@intel.com
The cycle time of FIFO clock should increase 2 times to avoid
the random recording noise issue.
This setting could apply to all known situations in i2s mode.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200317073308.11572-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses a hard-coded value for FW version and reports an
inconsistent FW version between ibv_devinfo and
/sys/class/infiniband/i40iw/fw_ver.
Retrieve the FW version via a Control QP (CQP) operation and report it
consistently across sysfs and query device.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Link: https://lore.kernel.org/r/20200313214406.2159-1-shiraz.saleem@intel.com
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Sindhu, Devale <sindhu.devale@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
As a result of commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail) and changes to various debugfs
functions in drm/core and across various drivers, there is no need for
the drm_driver.debugfs_init() hook to have a return value. Therefore,
declare it as void.
This also includes refactoring all users of the .debugfs_init() hook to
return void across the subsystem.
v2: include changes to the hook and drivers that use it in one patch to
prevent driver breakage and enable individual successful compilation of
this change.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-18-wambui.karugax@gmail.com
(uint16_t) st_shndx is limited to 65535(i.e. SHN_XINDEX) so sym_get_data() gets
wrong section index by st_shndx if requested symbol contains extended section
index that is more than 65535. In this case, we need to get proper section index
by .symtab_shndx section.
Module.symvers generated by building kernel with "-ffunction-sections -fdata-sections"
shows the issue.
Fixes: 56067812d5 ("kbuild: modversions: add infrastructure for emitting relative CRCs")
Fixes: e84f9fbbec ("modpost: refactor namespace_from_kstrtabns() to not hard-code section name")
Signed-off-by: Xiao Yang <yangx.jy@cn.fujitsu.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This is just a cleanup addition to Jann's fix to properly update the
transaction ID for the slub slowpath in commit fd4d9c7d0c ("mm: slub:
add missing TID bump..").
The transaction ID is what protects us against any concurrent accesses,
but we should really also make sure to make the 'freelist' comparison
itself always use the same freelist value that we then used as the new
next free pointer.
Jann points out that if we do all of this carefully, we could skip the
transaction ID update for all the paths that only remove entries from
the lists, and only update the TID when adding entries (to avoid the ABA
issue with cmpxchg and list handling re-adding a previously seen value).
But this patch just does the "make sure to cmpxchg the same value we
used" rather than then try to be clever.
Acked-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARN if the encoder possible_crtcs is effectively empty or contains
bits for non-existing crtcs.
v2: Move to drm_mode_config_validate() (Daniel)
Make the docs say we WARN when this is wrong (Daniel)
Extract full_crtc_mask()
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211162208.16224-7-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many drivers are populating encoder->possible_clones wrong. Let's
persuade them to get it right by adding some loud WARNs.
We'll cross check the bits between any two encoders. So either
both encoders can clone with the other, or neither can.
We'll also complain about effectively empty possible_clones, and
possible_clones containing bits for encoders that don't exist.
v2: encoder->possible_clones now includes the encoder itelf
v3: Move to drm_mode_config_validate() (Daniel)
Document that you get a WARN when this is wrong (Daniel)
Extract full_encoder_mask()
v4: !! instead of ! (Daniel)
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211162208.16224-6-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not at all clear what cloning options this driver supports.
So let's just clear possible_clones instead of setting it to some
bogus value.
v2: Adjust the FIXME (Daniel)
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211162208.16224-5-ville.syrjala@linux.intel.com
I doubt the DP+DP and SDVO+SDVO cloning works for this driver.
i915 at least doesn't do those. Truthfully there could be some very
specific circumstances where some of them would do doable, but
genereally it's too much pain to deal with so we've chose not to
bother. Let's use the same approach for gma500.
Also the LVDS+LVDS and DSI+DSI cases probably don't really exist as
there is one of each at most.
This does mean we'll now leave possible_clones at 0 for these encoder
types whereas previosuly we included the encoder itself in the bitmask.
But that's fine as the core now treaks 0 as a special case and adds
the encoder itself into the final bitmask reported to userspace.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211162208.16224-3-ville.syrjala@linux.intel.com
The docs say possible_clones should always include the encoder itself.
Since most drivers don't want to deal with the complexities of cloning
let's allow them to set possible_clones=0 and instead we'll fix that
up in the core.
We can't put this special case into drm_encoder_init() because drivers
will have to fill up possible_clones after adding all the relevant
encoders. Otherwise they wouldn't know the proper encoder indexes to
use. So we'll just do it just before registering the device.
v2: Don't set the bit if possible_clones!=0 so that the
validation (coming soon) will WARN (Thomas)
Fix up the docs to allow possible_clones==0 (Daniel)
.late_register() is too late, introduce drm_mode_config_validate()
which gets called _before_ we register the char device (Daniel)
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211162208.16224-2-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since 987d65d013 (drm: debugfs: make drm_debugfs_create_files() never
fail), there is no need to check the return value of
drm_debugfs_create_files(). Therefore, remove remove unnecessary checks
and error handling statement blocks for its return value.
These changes also enable changing drm_debugfs_create_files() to return
void.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-17-wambui.karugax@gmail.com
When kmem_cache_alloc_bulk() attempts to allocate N objects from a percpu
freelist of length M, and N > M > 0, it will first remove the M elements
from the percpu freelist, then call ___slab_alloc() to allocate the next
element and repopulate the percpu freelist. ___slab_alloc() can re-enable
IRQs via allocate_slab(), so the TID must be bumped before ___slab_alloc()
to properly commit the freelist head change.
Fix it by unconditionally bumping c->tid when entering the slowpath.
Cc: stable@vger.kernel.org
Fixes: ebe909e0fd ("slub: improve bulk alloc strategy")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the DispID tile block gets parsed in drm_get_edid(), which
is an odd place for it considering we parse nothing else there. Also
this doesn't work for override EDIDs since
drm_connector_update_edid_property() refuses to do its job twice
in such cases. Thus we never update the tile property with results
of the DispID tile block parsing during drm_get_edid().
To fix this let's just move the tile block parsing to happen during
drm_connector_update_edid_property(), which is where we parse a bunch
of other stuff as well (and where we update both the EDID and tile
properties).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313162054.16009-10-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Throw out the magic '5' from validate_displayid() and replace with
the actual thing we mean sizeof(header)+checksum. Also rewrite the
checksum loop to be less hard to parse for mere mortals.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313162054.16009-9-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Currently the code assumes that the entire EDID extesion block
can be taken up by the DispID blocks. That is not true. There
is at least always the DispID checksum, and potentially fill
bytes if the extension block uses the interior fill scheme
to pad out to fill EDID block size.
So let's not parse the checksum or the fill bytes as DispID
blocks by having drm_find_displayid_extension() return the
actual length of the DispID data to the caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313162054.16009-7-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
As with the byte offset (idx) drm_find_displayid_extension() is
the only one who actually knows how much data the resulting DispID
block can contain. So return the length from therein instead of
assuming it's the EDID block length all over.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313162054.16009-5-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The fact that the DispID starts at byte offset 1 is due to
the DispID coming from and EDID extension block (the first byte
being the extesion block tag). Instead of hadrdocoding that idx==1
assumptions all over let's just have drm_find_displayid_extension()
return it since it actually knows what it's talking about.
If at some point someone comes across a DispID which is not embedded
inside an EDID the function that returns the new type of DispID
can return it's own byte offset without having to updated all the
code.
TODO: should probably just get rid of that idx thing altogether
and just return the thing we want directly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313162054.16009-4-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove its use as the
return value of various debugfs_init() functions in drm, and have these
functions return 0 directly.
v2: convert debugfs_init() functions to return 0 instead of void to
avoid build breakage.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-16-wambui.karugax@gmail.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove its use as the
return value of debugfs_init() functions and have the functions return
void.
v2: convert intel_display_debugfs_register() stub to return void too.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-15-wambui.karugax@gmail.com
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), there is no need to ever check
the return value for drm_debugfs_create_files(). Therefore remove the
checks for the return value and subsequent error handling in
omap_debugfs_init().
These changes also enables the changing of omap_debugfs_init() to return
0 directly.
v2: convert omap_debugfs_init() to return 0 instead of void to avoid
introduction of build issues and enable individual driver compilation.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-14-wambui.karugax@gmail.com
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), there is no need to ever check
for the the return value of debugfs_create_file() and
drm_debugfs_create_files(). Therefore, remove unnecessary checks and
error handling in nouveau_drm_debugfs_init() and have the function
return 0 directly.
v2: have nouveau_drm_debugfs_init() return 0 instead of void so as not
to introduce any build warnings to enable individual patch compilation.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-12-wambui.karugax@gmail.com
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove its use as the
return value of drm_vram_mm_debugfs_init(), and have the function
return 0 directly.
v2: have drm_vram_mm_debugfs_init() return 0 instead of void to avoid
introducing build issues and build breakage.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-11-wambui.karugax@gmail.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails, and should return void. This change therefore removes it uses as
a return value in various functions across drm/sti.
With these changes, the affected functions have been changed to use a void
return value.
v2: convert sti_mixer_debugfs_init() and sti_compositor_debugfs_init()
to return void too. Also have sti_drm_dbg_init() to return 0 to avoid
build issues.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-10-wambui.karugax@gmail.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files never
fails and only returns 0. Therefore, the unnecessary checks for its
return value and error handling in various debugfs_init() functions in
drm/msm and have the functions return 0 directly.
v2: have debug functions return 0 instead of void to avoid build
breakage and ensure standalone compilation.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-9-wambui.karugax@gmail.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and only returns 0. Therefore, remove the unnecessary check of its
return value and error handling in etnaviv_debugfs_init() and have the
function return 0 directly.
v2: have etnaviv_debugfs_init() return 0 instead of void to ensure
individual compilation and avoid build breakage.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-8-wambui.karugax@gmail.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove its use as the
return value of hdlcd_debugfs_init() and have the latter function return
0 directly.
v2: make hdlcd_debugfs_init() return 0 instead of void to ensure that
each patch compiles individually.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-7-wambui.karugax@gmail.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove its use as the
return value of arcpgu_debugfs_init() and have the latter function return
0 directly.
v2: convert the function to return 0 instead of void to avoid breaking
the build and ensure that this individual patch compiles properly.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-6-wambui.karugax@gmail.com
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove unnecessary check and
error handling for the return value of drm_debugfs_create_files()
in vc4_debugfs_init().
v2: remove conversion of vc4_debugfs_init() to void to enable individual
compilation and avoid build issues and breakage.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-5-wambui.karugax@gmail.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove its use as the
return value of v3d_debugfs_init() and have the function return 0
directly instead.
v2: remove conversion of v3d_debugfs_init() to void to avoid build
breakage and enable individual compilation.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-4-wambui.karugax@gmail.com
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails. Therefore, remove the check and error handling of the return
value of drm_debugfs_create_files() as it is not needed in
tilcdc_debugfs_init().
Also remove local variables that are not used after the changes.
v2: remove conversion of tilcdc_debugfs_init() to void to avoid build
breakage and enable individual compilation.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-3-wambui.karugax@gmail.com
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail) there is no need to check the
return value of drm_debugfs_create_files(). Therefore, remove the
return checks and error handling of the drm_debugfs_create_files()
function from various debugfs init functions in drm/tegra and have
them return 0 directly.
v2: remove conversion of tegra_debugfs_init() to void to avoid build
breakage.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-2-wambui.karugax@gmail.com
AIL removal of the quotaoff start intent and free of both quotaoff
intents is currently limited to the ->iop_committed() handler of the
end intent. This executes when the end intent is committed to the
on-disk log and marks the completion of the operation. The problem
with this is it assumes the success of the operation. If a shutdown
or other error occurs during the quotaoff, it's possible for the
quotaoff task to exit without removing the start intent from the
AIL. This results in an unmount hang as the AIL cannot be emptied.
Further, no other codepath frees the intents and so this is also a
memory leak vector.
First, update the high level quotaoff error path to directly remove
and free the quotaoff start intent if it still exists in the AIL at
the time of the error. Next, update both of the start and end
quotaoff intents with an ->iop_release() callback to properly handle
transaction abort.
This means that If the quotaoff start transaction aborts, it frees
the start intent in the transaction commit path. If the filesystem
shuts down before the end transaction allocates, the quotaoff
sequence removes and frees the start intent. If the end transaction
aborts, it removes the start intent and frees both. This ensures
that a shutdown does not result in a hung unmount and that memory is
not leaked regardless of when a quotaoff error occurs.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
AIL removal of the quotaoff start intent and free of both intents is
hardcoded to the ->iop_committed() handler of the end intent. Factor
out the start intent handling code so it can be used in a future
patch to properly handle quotaoff errors. Use xfs_trans_ail_remove()
instead of the _delete() variant to acquire the AIL lock and also
handle cases where an intent might not reside in the AIL at the
time of a failure.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Add support for btree staging cursors for the rmap btrees. This is
needed both for online repair and also to convert xfs_repair to use
btree bulk loading.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Add support for btree staging cursors for the refcount btrees. This
is needed both for online repair and also to convert xfs_repair to use
btree bulk loading.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Add support for btree staging cursors for the inode btrees. This
is needed both for online repair and also to convert xfs_repair to use
btree bulk loading.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
