NFP flower offload uses delayed stats. Kernel recently gained
the ability to specify stats types. Make nfp accept DELAYED
stats, not just the catch all "any".
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger says:
====================
net: bcmgenet: revisit MAC reset
Commit 3a55402c93 ("net: bcmgenet: use RGMII loopback for MAC
reset") was intended to resolve issues with reseting the UniMAC
core within the GENET block by providing better control over the
clocks used by the UniMAC core. Unfortunately, it is not
compatible with all of the supported system configurations so an
alternative method must be applied.
This commit set provides such an alternative. The first commit
reverts the previous change and the second commit provides the
alternative reset sequence that addresses the concerns observed
with the previous implementation.
This replacement implementation should be applied to the stable
branches wherever commit 3a55402c93 ("net: bcmgenet: use RGMII
loopback for MAC reset") has been applied.
Unfortunately, reverting that commit may conflict with some
restructuring changes introduced by commit 4f8d81b77e ("net:
bcmgenet: Refactor register access in bcmgenet_mii_config").
The first commit in this set has been manually edited to
resolve the conflict on net/master. I would be happy to help
stable maintainers with resolving any such conflicts if they
occur. However, I do not expect that commit to have been
backported to stable branch so hopefully the revert can be
applied cleanly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked at least 5
cycles while the sw_reset is asserted to ensure a clean reset.
That commit enabled local loopback to provide an Rx clock from the
GENET sourced Tx clk. However, when connected in MII mode the Tx
clk is sourced by the PHY so if an EPHY is not supplying clocks
(e.g. when the link is down) the UniMAC does not receive the
necessary clocks.
This commit extends the sw_reset window until the PHY reports that
the link is up thereby ensuring that the clocks are being provided
to the MAC to produce a clean reset.
One consequence is that if the system attempts to enter a Wake on
LAN suspend state when the PHY link has not been active the MAC
may not have had a chance to initialize cleanly. In this case, we
remove the sw_reset and enable the WoL reception path as normal
with the hope that the PHY will provide the necessary clocks to
drive the WoL blocks if the link becomes active after the system
has entered suspend.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3a55402c93.
This is not a good solution when connecting to an external switch
that may not support the isolation of the TXC signal resulting in
output driver contention on the pin.
A different solution is necessary.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: improve phy_driver callback handle_interrupt
did_interrupt() clears the interrupt, therefore handle_interrupt() can
not check which event triggered the interrupt. To overcome this
constraint and allow more flexibility for customer interrupt handlers,
let's decouple handle_interrupt() from parts of the phylib interrupt
handling. Custom interrupt handlers now have to implement the
did_interrupt() functionality in handle_interrupt() if needed.
Fortunately we have just one custom interrupt handler so far (in the
mscc PHY driver), convert it to the changed API and make use of the
benefits.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trigger the respective interrupt handler functionality only if the
related interrupt source bit is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
did_interrupt() clears the interrupt, therefore handle_interrupt() can
not check which event triggered the interrupt. To overcome this
constraint and allow more flexibility for customer interrupt handlers,
let's decouple handle_interrupt() from parts of the phylib interrupt
handling. Custom interrupt handlers now have to implement the
did_interrupt() functionality in handle_interrupt() if needed.
Fortunately we have just one custom interrupt handler so far (in the
mscc PHY driver), convert it to the changed API.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all in-tree drivers have been updated we can
make the supported_coalesce_params mandatory.
To save debugging time in case some driver was missed
(or is out of tree) add a warning when netdev is registered
with set_coalesce but without supported_coalesce_params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters.
While at it remove unnecessary zeroing on get.
No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
The check for use_adaptive_tx_coalesce will now be done by
the core.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Packham says:
====================
net: mvmdio: avoid error message for optional IRQ
I've gone ahead an sent a revert. This is the same as the original v1 except
I've added Andrew's review to the commit message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e1f550dc44.
platform_get_irq_optional() will still return -ENXIO when no interrupt
is provided so the additional error handling caused the driver prone to
fail when no interrupt was specified. Revert the change so we can apply
the correct minimal fix.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
htotal*vtotal*vrefresh ~= clock. So just use say "clock" when we mean it.
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
New Chrome OS keyboards have a "snip" key that is basically a selective
screenshot (allows a user to select an area of screen to be copied).
Allocate a keycode for it.
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Link: https://lore.kernel.org/r/20200313180333.75011-1-rajatja@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not allow forwarding of encapsulated traffic received from one eswtich's
uplink to another eswtich's uplink.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add dependencny on cap termination_table_raw_traffic to allow non
encapsulated packets received from uplink to be forwarded back to the
received uplink port.
Refactor the conditions into a separate function.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Termination tables change the direction of a packet in hw from RX to SX
pipeline. Use that to offload hairpin flows received from uplink and
sent back to uplink.
Currently termination tables are used for pushing VLAN to packets
received from uplink and targeting a VF. Extend the implementation to
allow forwarding packets to uplink. These packets can either be
encapsulated or not.
In case encapsulation is needed before forwarding, move the reformat
object to the termination table as required.
Extend the hash table key to include tunnel information for the sake of
reusing reformat objects.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Don't use termination tables for packets that are steered to the slow path,
as a pre-step for supporting packet encap (packet reformat) action on
termination tables. Packet encap (reformat action) actions steer the packet
to the slow path until outer arp entries are resolved.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Check if QoS is enabled for the eswitch before attempting to configure
QoS parameters and emit a netlink error if not supported.
Introduce an API to check if QoS is supported for the eswitch.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If udevd is configured to rename interfaces according to persistent
naming rules and if a network interface has phys_port_name in sysfs,
its contents will be appended to the interface name.
However, register_netdev creates device in sysfs and if
devlink_port_register is called after that, there is a timeframe in
which udevd may read an empty phys_port_name value. The consequence is
that the interface will lose this suffix and its name will not be
really persistent.
The solution is to register the port before registering a netdev.
Fixes: c6acd629ee ("net/mlx5e: Add support for devlink-port in non-representors mode")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The original condition rejected all egress rules that
are not on tunnel device.
Also, the whole point of this egress reject was to disallow bad
rules because of egdev which doesn't exists today, so remove
this check entirely.
Fixes: 0a7fcb78cc ("net/mlx5e: Support inner header rewrite with goto action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Register loopback which is needed for tunnel restoration, is now always
enabled if supported and not just with metadata enabled, check for
that instead.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix the following warnings: [-Werror=frame-larger-than=]
In function ‘mlx5_tc_ct_entry_add_rule’:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:541:1:
error: the frame size of 1136 bytes is larger than 1024 bytes
In function ‘__mlx5_tc_ct_flow_offload’:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:1049:1:
error: the frame size of 1168 bytes is larger than 1024 bytes
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
If CONFIG_MLX5_TC_CT isn't enabled, all offloading of eswitch tc rules
fails on parsing ct match, even if there is no ct match.
Return success if there is no ct match, regardless of config.
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:
In function mlx5_tc_ct_parse_match:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:699:36: warning:
variable unnew set but not used [-Wunused-but-set-variable]
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Restore modify header writes the chain mapping on the packet.
This modify header and action is added on all prios connections,
and gets overwritten with the same value consecutively in prios
of the same chain.
Use the chain's modify header only for the last prio of a given tc
chain.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, if firmware doesn't support fwd and modify, driver fails
initializing eswitch chains while entering switchdev mode.
Instead, on such cases, disable the chains and prio feature (as we can't
restore the chain on miss) and the usage of fwd and modify.
Fixes: 8f1e0b97cc ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When CONFIG_MLX5_ESWITCH is unset, clang warns:
In file included from drivers/net/ethernet/mellanox/mlx5/core/main.c:58:
drivers/net/ethernet/mellanox/mlx5/core/eswitch.h:670:1: warning: unused
function 'esw_add_restore_rule' [-Wunused-function]
esw_add_restore_rule(struct mlx5_eswitch *esw, u32 tag)
^
1 warning generated.
This stub function is missing inline; add it to suppress the warning.
Fixes: 11b717d615 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Commit e687ad60af ("netfilter: add netfilter ingress hook after
handle_ing() under unique static key") introduced the ability to
classify packets on ingress.
Allow the same on egress. Position the hook immediately before a packet
is handed to tc and then sent out on an interface, thereby mirroring the
ingress order. This order allows marking packets in the netfilter
egress hook and subsequently using the mark in tc. Another benefit of
this order is consistency with a lot of existing documentation which
says that egress tc is performed after netfilter hooks.
Egress hooks already exist for the most common protocols, such as
NF_INET_LOCAL_OUT or NF_ARP_OUT, and those are to be preferred because
they are executed earlier during packet processing. However for more
exotic protocols, there is currently no provision to apply netfilter on
egress. A common workaround is to enslave the interface to a bridge and
use ebtables, or to resort to tc. But when the ingress hook was
introduced, consensus was that users should be given the choice to use
netfilter or tc, whichever tool suits their needs best:
https://lore.kernel.org/netdev/20150430153317.GA3230@salvia/
This hook is also useful for NAT46/NAT64, tunneling and filtering of
locally generated af_packet traffic such as dhclient.
There have also been occasional user requests for a netfilter egress
hook in the past, e.g.:
https://www.spinics.net/lists/netfilter/msg50038.html
Performance measurements with pktgen surprisingly show a speedup rather
than a slowdown with this commit:
* Without this commit:
Result: OK: 34240933(c34238375+d2558) usec, 100000000 (60byte,0frags)
2920481pps 1401Mb/sec (1401830880bps) errors: 0
* With this commit:
Result: OK: 33997299(c33994193+d3106) usec, 100000000 (60byte,0frags)
2941410pps 1411Mb/sec (1411876800bps) errors: 0
* Without this commit + tc egress:
Result: OK: 39022386(c39019547+d2839) usec, 100000000 (60byte,0frags)
2562631pps 1230Mb/sec (1230062880bps) errors: 0
* With this commit + tc egress:
Result: OK: 37604447(c37601877+d2570) usec, 100000000 (60byte,0frags)
2659259pps 1276Mb/sec (1276444320bps) errors: 0
* With this commit + nft egress:
Result: OK: 41436689(c41434088+d2600) usec, 100000000 (60byte,0frags)
2413320pps 1158Mb/sec (1158393600bps) errors: 0
Tested on a bare-metal Core i7-3615QM, each measurement was performed
three times to verify that the numbers are stable.
Commands to perform a measurement:
modprobe pktgen
echo "add_device lo@3" > /proc/net/pktgen/kpktgend_3
samples/pktgen/pktgen_bench_xmit_mode_queue_xmit.sh -i 'lo@3' -n 100000000
Commands for testing tc egress:
tc qdisc add dev lo clsact
tc filter add dev lo egress protocol ip prio 1 u32 match ip dst 4.3.2.1/32
Commands for testing nft egress:
nft add table netdev t
nft add chain netdev t co \{ type filter hook egress device lo priority 0 \; \}
nft add rule netdev t co ip daddr 4.3.2.1/32 drop
All testing was performed on the loopback interface to avoid distorting
measurements by the packet handling in the low-level Ethernet driver.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prepare for addition of a netfilter egress hook by generalizing the
ingress hook introduced by commit e687ad60af ("netfilter: add
netfilter ingress hook after handle_ing() under unique static key").
In particular, rename and refactor the ingress hook's static inlines
such that they can be reused for an egress hook.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prepare for addition of a netfilter egress hook by renaming
<linux/netfilter_ingress.h> to <linux/netfilter_netdev.h>.
The egress hook also necessitates a refactoring of the include file,
but that is done in a separate commit to ease reviewing.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A work queue cannot just rely on the ib_device not being freed, it must
hold a kref on the memory so that the BNXT_RE_FLAG_IBDEV_REGISTERED check
works.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/1584117207-2664-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There are a couple places in this driver running from a work queue that
need the ib_device to be registered. Instead of using a broken internal
bit rely on the new core code to guarantee device registration.
Link: https://lore.kernel.org/r/1584117207-2664-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
On a system configured to trigger a crash_kexec() reboot, when only one CPU
is online and another CPU panics while starting-up, crash_smp_send_stop()
will fail to send any STOP message to the other already online core,
resulting in fail to freeze and registers not properly saved.
Moreover even if the proper messages are sent (case CPUs > 2)
it will similarly fail to account for the booting CPU when executing
the final stop wait-loop, so potentially resulting in some CPU not
been waited for shutdown before rebooting.
A tangible effect of this behaviour can be observed when, after a panic
with kexec enabled and loaded, on the following reboot triggered by kexec,
the cpu that could not be successfully stopped fails to come back online:
[ 362.291022] ------------[ cut here ]------------
[ 362.291525] kernel BUG at arch/arm64/kernel/cpufeature.c:886!
[ 362.292023] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 362.292400] Modules linked in:
[ 362.292970] CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Not tainted 5.6.0-rc4-00003-gc780b890948a #105
[ 362.293136] Hardware name: Foundation-v8A (DT)
[ 362.293382] pstate: 200001c5 (nzCv dAIF -PAN -UAO)
[ 362.294063] pc : has_cpuid_feature+0xf0/0x348
[ 362.294177] lr : verify_local_elf_hwcaps+0x84/0xe8
[ 362.294280] sp : ffff800011b1bf60
[ 362.294362] x29: ffff800011b1bf60 x28: 0000000000000000
[ 362.294534] x27: 0000000000000000 x26: 0000000000000000
[ 362.294631] x25: 0000000000000000 x24: ffff80001189a25c
[ 362.294718] x23: 0000000000000000 x22: 0000000000000000
[ 362.294803] x21: ffff8000114aa018 x20: ffff800011156a00
[ 362.294897] x19: ffff800010c944a0 x18: 0000000000000004
[ 362.294987] x17: 0000000000000000 x16: 0000000000000000
[ 362.295073] x15: 00004e53b831ae3c x14: 00004e53b831ae3c
[ 362.295165] x13: 0000000000000384 x12: 0000000000000000
[ 362.295251] x11: 0000000000000000 x10: 00400032b5503510
[ 362.295334] x9 : 0000000000000000 x8 : ffff800010c7e204
[ 362.295426] x7 : 00000000410fd0f0 x6 : 0000000000000001
[ 362.295508] x5 : 00000000410fd0f0 x4 : 0000000000000000
[ 362.295592] x3 : 0000000000000000 x2 : ffff8000100939d8
[ 362.295683] x1 : 0000000000180420 x0 : 0000000000180480
[ 362.296011] Call trace:
[ 362.296257] has_cpuid_feature+0xf0/0x348
[ 362.296350] verify_local_elf_hwcaps+0x84/0xe8
[ 362.296424] check_local_cpu_capabilities+0x44/0x128
[ 362.296497] secondary_start_kernel+0xf4/0x188
[ 362.296998] Code: 52805001 72a00301 6b01001f 54000ec0 (d4210000)
[ 362.298652] SMP: stopping secondary CPUs
[ 362.300615] Starting crashdump kernel...
[ 362.301168] Bye!
[ 0.000000] Booting Linux on physical CPU 0x0000000003 [0x410fd0f0]
[ 0.000000] Linux version 5.6.0-rc4-00003-gc780b890948a (crimar01@e120937-lin) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #105 SMP PREEMPT Fri Mar 6 17:00:42 GMT 2020
[ 0.000000] Machine model: Foundation-v8A
[ 0.000000] earlycon: pl11 at MMIO 0x000000001c090000 (options '')
[ 0.000000] printk: bootconsole [pl11] enabled
.....
[ 0.138024] rcu: Hierarchical SRCU implementation.
[ 0.153472] its@2f020000: unable to locate ITS domain
[ 0.154078] its@2f020000: Unable to locate ITS domain
[ 0.157541] EFI services will not be available.
[ 0.175395] smp: Bringing up secondary CPUs ...
[ 0.209182] psci: failed to boot CPU1 (-22)
[ 0.209377] CPU1: failed to boot: -22
[ 0.274598] Detected PIPT I-cache on CPU2
[ 0.278707] GICv3: CPU2: found redistributor 1 region 0:0x000000002f120000
[ 0.285212] CPU2: Booted secondary processor 0x0000000001 [0x410fd0f0]
[ 0.369053] Detected PIPT I-cache on CPU3
[ 0.372947] GICv3: CPU3: found redistributor 2 region 0:0x000000002f140000
[ 0.378664] CPU3: Booted secondary processor 0x0000000002 [0x410fd0f0]
[ 0.401707] smp: Brought up 1 node, 3 CPUs
[ 0.404057] SMP: Total of 3 processors activated.
Make crash_smp_send_stop() account also for the online status of the
calling CPU while evaluating how many CPUs are effectively online: this way
the right number of STOPs is sent and all other stopped-cores's registers
are properly saved.
Fixes: 78fd584cde ("arm64: kdump: implement machine_crash_shutdown()")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
At present ARMv8 event counters are limited to 32-bits, though by
using the CHAIN event it's possible to combine adjacent counters to
achieve 64-bits. The perf config1:0 bit can be set to use such a
configuration.
With the introduction of ARMv8.5-PMU support, all event counters can
now be used as 64-bit counters.
Let's enable 64-bit event counters where support exists. Unless the
user sets config1:0 we will adjust the counter value such that it
overflows upon 32-bit overflow. This follows the same behaviour as
the cycle counter which has always been (and remains) 64-bits.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Mark: fix ID field names, compare with 8.5 value]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
We currently expose the PMU version of the host to the guest via
emulation of the DFR0_EL1 and AA64DFR0_EL1 debug feature registers.
However many of the features offered beyond PMUv3 for 8.1 are not
supported in KVM. Examples of this include support for the PMMIR
registers (added in PMUv3 for ARMv8.4) and 64-bit event counters
added in (PMUv3 for ARMv8.5).
Let's trap the Debug Feature Registers in order to limit
PMUVer/PerfMon in the Debug Feature Registers to PMUv3 for ARMv8.1
to avoid unexpected behaviour.
Both ID_AA64DFR0.PMUVer and ID_DFR0.PerfMon follow the "Alternative ID
scheme used for the Performance Monitors Extension version" where 0xF
means an IMPLEMENTATION DEFINED PMU is implemented, and values 0x0-0xE
are treated as with an unsigned field (with 0x0 meaning no PMU is
present). As we don't expect to expose an IMPLEMENTATION DEFINED PMU,
and our cap is below 0xF, we can treat these fields as unsigned when
applying the cap.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Mark: make field names consistent, use perfmon cap]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
When emulating ID registers there is often a need to cap the version
bits of a feature such that the guest will not use features that the
host is not aware of. For example, when KVM mediates access to the PMU
by emulating register accesses.
Let's add a helper that extracts a performance monitors ID field and
caps the version to a given value.
Fields that identify the version of the Performance Monitors Extension
do not follow the standard ID scheme, and instead follow the scheme
described in ARM DDI 0487E.a page D13-2825 "Alternative ID scheme used
for the Performance Monitors Extension version". The value 0xF means an
IMPLEMENTATION DEFINED PMU is present, and values 0x0-OxE can be treated
the same as an unsigned field with 0x0 meaning no PMU is present.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Mark: rework to handle perfmon fields]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reading this code bordered on painful, what with all the repetition and
pointless return values. More fundamentally, dribbling the hardware
enables and disables in one bit at a time incurs needless system
register overhead for chained events and on reset. We already use
bitmask values for the KVM hooks, so consolidate all the register
accesses to match, and make a reasonable saving in both source and
object code.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
