The CPU freqs are not supposed to change before cpufreq policies
properly registered, meaning that they should be used to calculate the
initial CPU capacities.
Doing this helps choosing the best CPU during early boot, especially
for the initramfs decompressing.
There's no functional changes for non-clk CPU DVFS mechanism.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Link: https://lore.kernel.org/r/20200113034815.25924-1-jeffy.chen@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the simpler sprintf() instead of snprintf() or scnprintf() in a
single-shot sysfs output callbacks where you are very sure that it
won't go over PAGE_SIZE buffer limit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311080207.12046-3-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311080207.12046-2-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All HCI device specific error messages shall use bt_dev_err to indicate
the device name in the message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the RPA generation fails, indicate the error with a device specifc
error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All HCI device specific error messages shall use bt_dev_err to indicate
the device name in the message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: /: compatible:
['rockchip,rk3399-evb', 'rockchip,rk3399', 'google,rk3399evb-rev2']
is not valid under any of the given schemas
'google,rk3399evb-rev2' was a no longer used variant for Google.
The binding only mentions 'rockchip,rk3399-evb', 'rockchip,rk3399',
so fix this error by removing 'google,rk3399evb-rev2' from
the compatible property in rk3399-evb.dts and change it into
generic rk3399-evb support only.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302092759.3291-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm/boot/dts/rk3036-evb.dt.yaml: /: compatible:
['rockchip,rk3036-evb', 'rockchip,rk3036']
is not valid under any of the given schemas
This board was somehow never added to the documentation.
Fix this error by adding the rk3036-evb board to rockchip.yaml.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200302092759.3291-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm/boot/dts/rk3036-kylin.dt.yaml: /: compatible:
['rockchip,rk3036-kylin', 'rockchip,rk3036']
is not valid under any of the given schemas
Normally the dt-binding is the authoritative part, so boards should follow
the binding, but in the kylin-case the compatible from the .dts is used for
years in the field now, so fix the binding, as otherwise
we would break old users.
Fix this error by changing 'rockchip,kylin-rk3036' to
'rockchip,rk3036-kylin' in rockchip.yaml.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200302092759.3291-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When trying to transmit to an unknown destination, the mesh code would
unconditionally transmit a HWMP PREQ even if HWMP is not the current
path selection algorithm.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://lore.kernel.org/r/20200305140409.12204-1-cavallar@lri.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The GW5910-C revision adds a TI CC1352 connected to IMX UART4
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Convert the Renesas Clock Pulse Generator / Module Standby and Software
Reset Device Tree binding documentation to json-schema.
Note that #reset-cells was incorrecty marked a required property for
RZ/A2 before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200303094848.23670-1-geert+renesas@glider.be
In one of the iWave-G22D development board variants, called Generic SODIMM
Development Platform, we have an LCD with touchscreen. The resistive touch
controller, STMPE811 is on the development board and is connected through
the i2c5 of the RZ-G1E.
Additionally, this controller should generate an interrupt to the CPU and
it is connected through GPIO4,4 to the GIC.
Touch was tested with one of our iW-RainboW-G22D-SODIMM RZ/G1E development
platforms.
More details on the iWave website:
https://www.iwavesystems.com/rz-g1e-sodimm-development-kit.html
Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1583336650-25848-1-git-send-email-marian-cristian.rotariu.rb@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On the Generic SODIMM Development Platform there is an RGB LCD panel
directly connected to the DU output. It uses the TPU0 as backlight, one
GPIO pull-up configuration for power enable, R[2:7], G[2:7], B[2:7],
VSYNC, HSYNC, DU0_DISP and, DU0_CLK as inputs.
There is no encoder between the DU and the panel, therefore the default
connector driver is used.
The two variants of the iW-G22D should be mutually exclusive, therefore
this patch also disables the RGB LCD display when the HDMI extension board
is used.
Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1583239490-8837-1-git-send-email-marian-cristian.rotariu.rb@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The IMU chip on the librem5-devkit is not mounted at the "natural" place
that would match normal phone orientation (see the documentation for the
details about what that is).
Since the lsm9ds1 driver supports providing a mount matrix, we can describe
the orientation on the board in the dts:
Create a right-handed coordinate system (x * -1; see the datasheet for the
axis) and rotate 180 degrees around the y axis because the device sits on
the back side from the display.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The poly fuses can handle 6V 4Amps so incease the kernel limts to 5V
3.5Amps.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By adding broken-cd to the usdhc2 stanza the Redpine card can be
detected when the HKS is turned off and on.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify which regulator is used for cpufreq DVFS.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Connect the WoWWAN signal to a gpio key to wake up the system from suspend.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the simcom SIM7100 modem and the sai6 interface that connects it.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the sgtl5000 of the librem 5 devkit in devicetree.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Without a VBUS supply the dwc3 driver won't go into otg mode.
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing attribute validation for beacon report scanning
to the netlink policy.
Fixes: 1d76250bd3 ("nl80211: support beacon report scanning")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20200303051058.4089398-3-kuba@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds 4 eeprom support on i2c mux channel #0 -
1. Bootable 512Kbit eeprom at address 0x50.
2. Memory SO-DIMMs SPD channels at 0x51 (upper SO-DIMM) and 0x53.
3. 2Kb eeprom at 0x57 will be used by SolidRun to hold manufacturing
data.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the LTC3882 regulator so that the hardware monitoring
can be used with this device. This regulator provides the 0.78V
supply for the LX2160A.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX8M SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MM, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MM, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit b9213899d2b0 ("arm64: dts: ls1028a: disable all enetc ports
by default") all the network ports are disabled by default. This makes
sense, but now we have to enable them explicitly in the boards. Do so
for the sl28 module.
Since we are at it. Make sure the second port is only enabled for the
variant 4 of the module. Variant 3 has only one network port.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Link the switch PHY nodes to the central MDIO controller PCIe endpoint
node on LS1028A (implemented as PF3) so that PHYs are accessible via
MDIO.
Enable SGMII AN on the Felix PCS by telling PHYLINK that the VSC8514
quad PHY is capable of in-band-status.
The PHYs are used in poll mode due to an issue with the interrupt line
on current revisions of the LS1028A-RDB board.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the switch device node, available on PF5, so that the switch port
sub-nodes (net devices) can be linked to corresponding board specific
phy nodes (external ports) or have their link mode defined (internal
ports).
The switch device features 6 ports, 4 with external links and 2
internally facing to the LS1028A SoC and connected via fixed links to 2
internal ENETC Ethernet controller ports.
Add the corresponding ENETC host port device nodes, mapped to PF2 and
PF6 PCIe functions. Since the switch only supports tagging on one CPU
port, only one port pair (swp4, eno2) is enabled by default and the
other, lower speed, port pair is disabled to prevent the PCI core from
probing them. If enabled, swp5 will be a fixed-link slave port.
DSA tagging can also be moved from the swp4-eno2 2.5G port pair to the
1G swp5-eno3 pair by changing the ethernet = <&enetc_port2> phandle to
<&enetc_port3> and moving it under port5, but in that case enetc_port2
should not be disabled, because it is the hardware owner of the Felix
PCS and disabling its memory would result in access faults in the Felix
DSA driver.
All ports are disabled by default, including the CPU port, and need to
be enabled on a per-board basis.
The phy-mode binding of the internal ENETC ports was modified from
"gmii" to "internal" to match the phy-mode of the internal-facing switch
ports connected to them. The ENETC driver does not perform any phy_mode
validation anyway, so the change is only cosmetic. Also, enetc_port2 is
defined as a fixed-link 1000 Mbps port even though it is 2500 Mbps (as
can be seen by the fact that it is connected to mscc_felix_port4). The
fact that it is currently defined as 1000 Mbps is an artifact of its
PHYLIB implementation instead of PHYLINK (the former can't describe a
fixed-link speed higher than what swphy can emulate from the Clause 22
MDIO spec).
The switch's INTB interrupt line signals:
- PTP TX timestamp availability
- TSN Frame Preemption
And don't forget to enable the 4MB BAR4 in the root complex ECAM space,
where the switch registers are mapped.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are few boards that enable all ENETC ports, so instead of having
board DTs disable them, do so in the DTSI and have the boards enable the
ports they use.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This specifier overrides the interrupt specifier with 3 cells from gic
(/interrupt-controller@6000000), but in fact ENETC is not an interrupt
controller, so the property is bogus.
Interrupts used by the children of the ENETC RCIE must use the full
3-cell specifier required by the GIC.
The issue has no functional consequence so there is no real reason to
port the patch to stable trees.
Fixes: 927d7f8575 ("arm64: dts: fsl: ls1028a: Add PCI IERC node and ENETC endpoints")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We need to indicate that powering off the TI WiFi is safe, to avoid:
wl18xx_driver wl18xx.2.auto: Unbalanced pm_runtime_enable!
wl1271_sdio mmc0:0001:2: wl12xx_sdio_power_on: failed to get_sync(-13)
which prevents the WiFi being functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pmic is a mfd device and supports gpios. Those gpios are not routed
to the SoM baseboard pin header but they are connected to the i.MX6. We
need the GPIO's to configure the pmic to select between the
suspend/resume arm and soc voltages
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By default the phycore-som has support for two watchdog devices: 1st the
internal imx6 watchdog and 2nd the DA9062 PMIC watchdog. According [1]
the PMIC watchdog is used as boot watchdog. It is common to use this
watchdog during "system up" time too. Furthermore the PMIC watchdog can
be used to address ERR007117 since the phycore-som can be equipped with
NAND or eMMC storage.
The PMIC watchdog can be enabled/disabled by the PMIC itself if the PMIC
enters POWERDOWN mode or by the host. The PMIC powerdown mode can't be
used due to the PCB design. So the watchdog is still enabled during a
suspend which causes a system reset. We need to tell the driver to
disable the watchdog during a system suspend and to reenable it upon a
resume to fix this.
[1] https://git.pengutronix.de/cgit/barebox/tree/arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi#n73
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When we do the initial CPU reset we must not only clear the registers
in the internal data structures but also in kvm_run sync_regs. For
modern userspace sync_regs is the only place that it looks at.
Fixes: 7de3f1423f ("KVM: s390: Add new reset vcpu API")
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX6/7 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
src_base is already checked during src driver initialization, no
need to check its availability again when using it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Access to result of ieee80211_bss_get_ie() is protected by RCU. In other
hand, function hif_join() can sleep and cannot be called with RCU
locked.
Provide a copy of "ssidie" to hif_join() to solve this behavior.
Fixes: 9ced9b5937 ("staging: wfx: simplify hif_join()")
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200310101356.182818-6-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
