Stop removing modes that are not supported on the system interface
when the connected PHY is capable of rate adaptation. This addresses
an issue with the LS1046ARDB board 10G interface no longer working
with an 1G link partner after autonegotiation support was added
for the Aquantia PHY on board in
commit 09c4c57f7b ("net: phy: aquantia: add support for auto-negotiation configuration")
Before this commit the values advertised by the PHY were not
influenced by the dpaa_eth driver removal of system-side unsupported
modes as the aqr_config_aneg() was basically a no-op. After this
commit, the modes removed by the dpaa_eth driver were no longer
advertised thus autonegotiation with 1G link partners failed.
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we may add new waiters to a request as it is being run, we need to
mark the list iteration as being safe for concurrent addition.
v2: Mika spotted that we used the same trick for signalers_list, so warn
the compiler about the lockless walk there as well.
Fixes: 32ff621fd7 ("drm/i915/gt: Allow temporary suspension of inflight requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207110213.2734386-1-chris@chris-wilson.co.uk
This is now a trivial patch, but for seeing the actual changes
I (Johannes) split it out from the original.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200115125522.3755-1-markus.theil@tu-ilmenau.de
[split into separate cfg80211/mac80211 patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using control port over nl80211 in AP mode with
pre-authentication, APs need to forward frames to other
APs defined by their MAC address. Before this patch,
pre-auth frames reaching user space over nl80211 control
port have no longer any information about the dest attached,
which can be used for forwarding to a controller or injecting
the frame back to a ethernet interface over a AF_PACKET
socket.
Analog problems exist, when forwarding pre-auth frames from
AP -> STA.
This patch therefore adds the NL80211_ATTR_DST_MAC and
NL80211_ATTR_SRC_MAC attributes to provide more context
information when forwarding.
The respective arguments are optional on tx and included on rx.
Therefore unaware existing software is not affected.
Software which wants to detect this feature, can do so
by checking against:
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_MAC_ADDRS
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200115125522.3755-1-markus.theil@tu-ilmenau.de
[split into separate cfg80211/mac80211 patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parse also the RSN Extension IE when parsing the rest of the IEs.
It will be used in a later patch.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-21-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support Pre Association Security Negotiation (PASN) while already
associated to one AP, allow user space to register to Rx
authentication frames, so that the user space logic would be able to
receive/handle authentication frames from a different AP as part of
PASN.
Note that it is expected that user space would intelligently register
for Rx authentication frames, i.e., only when PASN is used and
configure a match filter only for PASN authentication algorithm, as
otherwise the MLME functionality of mac80211 would be broken.
Additionally, since some versions of the user space daemons wrongly
register to all types of authentication frames (which might result in
unexpected behavior) allow such registration if the request is for a
specific authentication algorithm number.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131114529.894206-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When preparing ethtool drvinfo, check if wiphy driver is defined
before dereferencing it. Driver may not exist, e.g. if wiphy is
attached to a virtual platform device.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200203105644.28875-1-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SMPS feature is defined in the specification only to be
used by non-AP stations and not by APs, so remove the support
for changing the AP's SMPS mode dynamically.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-20-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to IEEE802.11 specifications the SM power save field
in the HT capability IE and the HE extended capability IE is valid
only in (re)association frames and should be ignored otherwise.
Remove code paths that handled this also for non AP modes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-17-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An AP that operates on 6GHz may respond with a broadcast probe response.
Don't ignore such frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-14-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HE, the RX NSS is taken from the HE capabilities.
If the supported NSS capabilities that are reported by AP for
HE mode in the HE Capabilities element are different from the NSS
capabilities that are reported by AP for the VHT mode in the VHT
Capabilities element, use the lowest supported NSS to not get all
the values confused.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-9-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the station bandwidth in HE capability parsing and from
HE capability as the HT/VHT information will not be present
on the 6 GHz band.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-5-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not include the supported channels element if we have
(advertise) support for extended channel switching. To avoid any
interop issues because we always added it in the past, obey this
restriction only in the (new) 6 GHz band.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131113111.893106-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disable HE if the beacon does not contain an HE operation IE.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-16-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function always returns 0, so there's no point in returning int.
Make it void and remove the impossible error-path when calling it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-11-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set ndev->hw_features as well as ndev->features to allow
changing the TX-related features with ethtool.
We cannot (yet) change RX-related features since that
requires telling the driver about it and we have no API
for that yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-10-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wireless device might be capable to connect HE
as well as the AP. However, the regulatory domain might
forbid it. Check whether the regulatory domain allows HE connection
when considering if HE IE should be added.
Also, add it when setting our peer capability.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-8-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code was really ugly, refactor it a bit to make it more
readable.
While at it, use sizeof() and fix the UORA element length
check bug.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-4-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check early on that a device has support for QoS (at least 4
queues) when it supports HT/VHT/HE, so we don't have to check
this while connecting.
This lets us clean up the code there: move some of it into
channel preparation to clean up a bit more, and then change
the logic to only check the "wmm_used" flag.
Additionally, disable HE consistently when VHT is disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-3-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ab4dfa2053 ("cfg80211: Allow drivers to advertise supported AKM
suites") introduces the support to advertize supported AKMs to userspace.
This needs an enhancement to advertize the AKM support per interface type,
specifically for the cfg80211-based drivers that implement SME and use
different mechanisms to support the AKM's for each interface type (e.g.,
the support for SAE, OWE AKM's take different paths for such drivers on
STA/AP mode).
This commit aims the same and enhances the earlier mechanism of advertizing
the AKMs per wiphy. Add new nl80211 attributes and data structure to
provide supported AKMs per interface type to userspace.
the AKMs advertized in akm_suites are default capabilities if not
advertized for a specific interface type in iftype_akm_suites.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/20200126203032.21934-1-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regulatory domain might forbid HE operation. Certain regulatory
domains may restrict it for specific channels whereas others may do it
for the whole regulatory domain.
Add an option to indicate it in the channel flag.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200121081213.733757-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit d2a4bb6f8b.
So, turns out that this ended up just breaking things. While many
laptops incorrectly advertise themselves as supporting PWM backlight
controls, they actually will only work with DPCD backlight controls.
Unfortunately, it also seems there are a number of systems which
advertise DPCD backlight controls in their eDP DPCD but don't actually
support them. Talking with some laptop manufacturers has shown it might
be possible to probe this support via the EDID (!?!?) but I haven't been
able to confirm that this would work on any other manufacturer's
systems.
So in the mean time, we'll just revert this commit for now and go back
to the old way of doing things.
Fixes: d2a4bb6f8b ("drm/i915: Don't use VBT for detecting DPCD backlight controls")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204192823.111404-2-lyude@redhat.com
Virtual engines are fleeting. They carry a reference count and may be freed
when their last request is retired. This makes them unsuitable for the
task of housing engine->retire.work so assert that it is not used.
Tvrtko tracked down an instance where we did indeed violate this rule.
In virtual_submit_request, we flush a completed request directly with
__i915_request_submit and this causes us to queue that request on the
veng's breadcrumb list and signal it. Leading us down a path where we
should not attach the retire.
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: dc93c9b693 ("drm/i915/gt: Schedule request retirement when signaler idles")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206204915.2636606-1-chris@chris-wilson.co.uk
We only use the parsing CRC for checking if a beacon changed,
and elements with an ID > 63 cannot be represented in the
filter. Thus, like we did before with WMM and Cisco vendor
elements, just statically add these forgotten items to the
CRC:
- WLAN_EID_VHT_OPERATION
- WLAN_EID_OPMODE_NOTIF
I guess that in most cases when VHT/HE operation change, the HT
operation also changed, and so the change was picked up, but we
did notice that pure operating mode notification changes were
ignored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-22-luca@coelho.fi
[restrict to VHT for the mac80211 branch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously I intended to ignore quiet mode in probe response, however
I ended up ignoring it instead for action frames. As a matter of fact,
this path isn't invoked for probe responses to start with. Just revert
this patch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 7976b1e9e3 ("mac80211: ignore quiet mode in probe")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-15-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ong Boon Leong says:
====================
net: stmmac: general fixes for Ethernet functionality
1/5: It ensures that the previous value of GMAC_VLAN_TAG register is
read first before for updating the register.
2/5: Similar to 2/6 patch but it is a fix for XGMAC_VLAN_TAG register
as requested by Jose Abreu.
3/5: It ensures the GMAC IP v4.xx and above behaves correctly to:-
ip link set <devname> multicast off|on
4/5: Added similar IFF_MULTICAST flag for xgmac2, similar to 4/6.
5/5: It ensures PCI platform data is using plat->phy_interface.
Changes from v4:-
patch 1/6 - this patch is dropped now and will take the input on
handling return value from netif_set_real_num_rx|
tx_queues() in future patch series.
v3:-
patch 1/6 - add rtnl_lock() and rtnl_unlock() for stmmac_hw_setup()
called inside stmmac_resume()
patch 3/6 - Added new patch to fix XGMAC_VLAN_TAG register writting
v2:-
patch 1/5 - added control for rtnl_lock() & rtnl_unlock() to ensure
they are used forstmmac_resume()
patch 4/5 - added IFF_MULTICAST flag check for xgmac to ensure
multicast works correctly.
v1:-
- Drop v1 patches (1/7, 3/7 & 4/7) that are not valid.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch to support passive mode converter did not take care the
phy interface configuration in PCI platform data. Hence, converting all
the PCI platform data from plat->interface to plat->phy_interface as the
default mode is meant for PHY.
Fixes: 0060c87833 ("net: stmmac: implement support for passive mode converters via dt")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 0efedbf11f ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Verma, Aashish <aashishx.verma@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should always do a read of current value of XGMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: 3cd1cfcba2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should always do a read of current value of GMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: c1be0022df ("net: stmmac: Add VLAN HASH filtering support in GMAC4+")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of XDP_SETUP_PROG has already incremented refcnt in
__bpf_prog_get(), so drivers should only increment refcnt by
num_queues - 1.
To fix the issue, update netvsc_xdp_set() to add the correct number
to refcnt.
Hold a refcnt in netvsc_xdp_set()’s other caller, netvsc_attach().
And, do the same in netvsc_vf_setxdp(). Otherwise, every time when VF is
removed and added from the host side, the refcnt will be decreased by one,
which may cause page fault when unloading xdp program.
Fixes: 351e158139 ("hv_netvsc: Add XDP support")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that this wasn't a good idea, I hit a test failure in
hwsim due to this. That particular failure was easily worked around,
but it raised questions: if an AP needs to, for example, send action
frames to each connected station, the current limit is nowhere near
enough (especially if those stations are sleeping and the frames are
queued for a while.)
Shuffle around some bits to make more room for ack_frame_id to allow
up to 8192 queued up frames, that's enough for queueing 4 frames to
each connected station, even at the maximum of 2007 stations on a
single AP.
We take the bits from band (which currently only 2 but I leave 3 in
case we add another band) and from the hw_queue, which can only need
4 since it has a limit of 16 queues.
Fixes: 6912daed05 ("mac80211: Shrink the size of ack_frame_id to make room for tx_time_est")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200115122549.b9a4ef9f4980.Ied52ed90150220b83a280009c590b65d125d087c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 802.11 encapsulation returned early when setting up the keys in case
offloading was enabled. This causes ieee802.11w to not work anymore. Fix
this by moving the check for offloading into the switch/case construct and
allowing CCMP/GCMP keys. With this patch applied ieee80211w works again
when enabling offloading.
Fixes: 50ff477a86 ("mac80211: add 802.11 encapsulation offloading support")
Reported-by: Maharaja Kennadyrajan <mkenna@qti.qualcomm.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200203122812.18993-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Vinicius Costa Gomes says:
====================
taprio: Some fixes
Changes from v3:
- Replaced ENOTSUPP error code with EOPNOTSUPP (Jakub Kicinski);
- Added the missing policy validation for the flags netlink argument
(Jakub Kicinski);
- Fixed the destroy() flow to also destroy the priority to traffic
class mapping (David Miller);
- Fixed dropping packets when taprio offloading is used together
with ETF offloading (more on this below);
Changes from v2:
- Squashed commits 2/3 and 3/3 into a single one (I think a single
commit is going to be easier to review);
- Removed an "improvement" that was causing changes in user visible
behavior;
Changes from v1:
- Fixed ignoring the 'flags' argument when adding a new
instance (Vladimir Oltean);
- Changed the order of commits;
Updated cover letter:
One bit that might need some attention is the fix for not dropping all
packets when taprio and ETF offloading are used, patch 5/5. The
behavior when the fix is applied is that packets that have a 'txtime'
that would fall outside of their transmission window are now dropped
by taprio. The question that might be raised is: should taprio be
responsible for dropping these packets, or should it be handled lower
in the stack?
My opinion is: taprio has all the information, and it's able to give
feeback to the user. Lower in the stack, those packets might go into
the void, and the only feedback could be a hard to find counter
increasing.
Patch 1/5: Reported by Po Liu, is more of a improvement of usability for
drivers implementing offloading features, now they can rely on the
value of dev->num_tc, instead of going through some hops to get this
value.
Patch 2/5: Use 'q->flags' as the source of truth for the offloading
flags. Tries to solidify the current behavior, while avoiding going
into invalid states, one of which was causing a "rcu stall" (more
information in the commit message).
Patch 3/5: Adds the missing netlink attribute validation for
TCA_TAPRIO_ATTR_FLAGS.
Patch 4/5: Replaces the usage of netdev_set_num_tc() with
netdev_reset_tc() in taprio_destroy(), taprio_destroy() is called when
applying a configuration fails, making sure that the device traffic
class configuration goes back to the default state.
@Vladimir: If possible, I would appreciate your Ack on patch 2/5. I
have been looking at this code for so long that I might have missed
something obvious (and my growing dislike for the word 'flags' may be
affecting my judgement :-).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using taprio offloading together with ETF offloading, configured
like this, for example:
$ tc qdisc replace dev $IFACE parent root handle 100 taprio \
num_tc 4 \
map 2 2 1 0 3 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 1@2 1@3 \
base-time $BASE_TIME \
sched-entry S 01 1000000 \
sched-entry S 0e 1000000 \
flags 0x2
$ tc qdisc replace dev $IFACE parent 100:1 etf \
offload delta 300000 clockid CLOCK_TAI
During enqueue, it works out that the verification added for the
"txtime" assisted mode is run when using taprio + ETF offloading, the
only thing missing is initializing the 'next_txtime' of all the cycle
entries. (if we don't set 'next_txtime' all packets from SO_TXTIME
sockets are dropped)
Fixes: 4cfd5779bd ("taprio: Add support for txtime-assist mode")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When destroying the current taprio instance, which can happen when the
creation of one fails, we should reset the traffic class configuration
back to the default state.
netdev_reset_tc() is a better way because in addition to setting the
number of traffic classes to zero, it also resets the priority to
traffic classes mapping to the default value.
Fixes: 5a781ccbd1 ("tc: Add support for configuring the taprio scheduler")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink policy validation for the 'flags' argument was missing.
Fixes: 4cfd5779bd ("taprio: Add support for txtime-assist mode")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver implementing taprio offloading depends on the value of
the network device number of traffic classes (dev->num_tc) for
whatever reason, it was going to receive the value zero. The value was
only set after the offloading function is called.
So, moving setting the number of traffic classes to before the
offloading function is called fixes this issue. This is safe because
this only happens when taprio is instantiated (we don't allow this
configuration to be changed without first removing taprio).
Fixes: 9c66d15646 ("taprio: Add support for hardware offloading")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 7445 switch clocking profiles do not allow us to run the IMP port at
2Gb/sec in a way that it is reliable and consistent. Make sure that the
setting is only applied to the 7278 family.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
b53_configure_vlan() is called by the bcm_sf2 driver upon setup and
indirectly through resume as well. During the initial setup, we are
guaranteed that dev->vlan_enabled is false, so there is no change in
behavior, however during suspend, we may have enabled VLANs before, so we
do want to restore that setting.
Fixes: dad8d7c645 ("net: dsa: b53: Properly account for VLAN filtering")
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It forgot to reduce the value of the variable retry in a while loop
in the ethqos_configure() function. It may cause an endless loop and
without timeout.
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxrpc_rcu_destroy_call(), which is called as an RCU callback to clean up a
put call, calls rxrpc_put_connection() which, deep in its bowels, takes a
number of spinlocks in a non-BH-safe way, including rxrpc_conn_id_lock and
local->client_conns_lock. RCU callbacks, however, are normally called from
softirq context, which can cause lockdep to notice the locking
inconsistency.
To get lockdep to detect this, it's necessary to have the connection
cleaned up on the put at the end of the last of its calls, though normally
the clean up is deferred. This can be induced, however, by starting a call
on an AF_RXRPC socket and then closing the socket without reading the
reply.
Fix this by having rxrpc_rcu_destroy_call() punt the destruction to a
workqueue if in softirq-mode and defer the destruction to process context.
Note that another way to fix this could be to add a bunch of bh-disable
annotations to the spinlocks concerned - and there might be more than just
those two - but that means spending more time with BHs disabled.
Note also that some of these places were covered by bh-disable spinlocks
belonging to the rxrpc_transport object, but these got removed without the
_bh annotation being retained on the next lock in.
Fixes: 999b69f892 ("rxrpc: Kill the client connection bundle concept")
Reported-by: syzbot+d82f3ac8d87e7ccbb2c9@syzkaller.appspotmail.com
Reported-by: syzbot+3f1fd6b8cbf8702d134e@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hillf Danton <hdanton@sina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch that substituted a flag on an rxrpc_call for the
connection pointer being NULL as an indication that a call was disconnected
puts the set_bit in the wrong place for service calls. This is only a
problem if a call is implicitly terminated by a new call coming in on the
same connection channel instead of a terminating ACK packet.
In such a case, rxrpc_input_implicit_end_call() calls
__rxrpc_disconnect_call(), which is now (incorrectly) setting the
disconnection bit, meaning that when rxrpc_release_call() is later called,
it doesn't call rxrpc_disconnect_call() and so the call isn't removed from
the peer's error distribution list and the list gets corrupted.
KASAN finds the issue as an access after release on a call, but the
position at which it occurs is confusing as it appears to be related to a
different call (the call site is where the latter call is being removed
from the error distribution list and either the next or pprev pointer
points to a previously released call).
Fix this by moving the setting of the flag from __rxrpc_disconnect_call()
to rxrpc_disconnect_call() in the same place that the connection pointer
was being cleared.
Fixes: 5273a191dc ("rxrpc: Fix NULL pointer deref due to call->conn being cleared on disconnect")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the virtio device supports indirect ring descriptors we need only one
ring entry for the whole command. Take that into account when checking
whenever the virtqueue has enough free entries for our command.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200207064653.14403-1-kraxel@redhat.com
Add the new file Documentation/filesystems/zonefs.txt to document
zonefs principles and user-space tool usage.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
