RGMII requires a delay of 2ns between the data and the clock signal.
There are at least three ways this can happen. One possibility is by
having the PHY generate this delay.
This is a common source for problems (for example with slow TX speeds or
packet loss when sending data). The TX delay configuration of the
RTL8211F PHY can be set either by pin-strappping the RXD1 pin (HIGH
means enabled, LOW means disabled) or through configuring a paged
register. The setting from the RXD1 pin is also reflected in the
register.
Add debug logging to the TX delay configuration on RTL8211F so it's
easier to spot these issues (for example if the TX delay is enabled for
both, the RTL8211F PHY and the MAC).
This is especially helpful because there is no public datasheet for the
RTL8211F PHY available with all the RX/TX delay specifics.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: spectrum_router: Cleanups
This patch set removes from mlxsw code that is no longer necessary after
the simplification of the IPv4 and IPv6 route offload API.
The patches eliminate unnecessary code by taking advantage of the fact
that mlxsw no longer needs to maintain a list of identical routes,
following recent changes in route offload API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in previous patches, the driver no longer needs to maintain
a list of identical FIB entries (i.e, same {tb_id, prefix, prefix
length}) and therefore each FIB node can only store one FIB entry.
Remove the FIB entry list and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last patch mlxsw_sp_fib{4,6}_node_entry_link() and
mlxsw_sp_fib{4,6}_node_entry_unlink() are identical and can therefore be
consolidated into the same common function.
Perform the consolidation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Host routes that perform decapsulation of IP in IP tunnels have a
special adjacency entry linked to them. This entry stores information
such as the expected underlay source IP. When the route is deleted this
entry needs to be freed.
The allocation of the adjacency entry happens in
mlxsw_sp_fib4_entry_type_set(), but it is freed in
mlxsw_sp_fib4_node_entry_unlink().
Create a new function - mlxsw_sp_fib4_entry_type_unset() - and free the
adjacency entry there.
This will allow us to consolidate mlxsw_sp_fib{4,6}_node_entry_unlink()
in the next patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver no longer maintains a list of identical routes there is
no route to promote when a route is deleted.
Remove that code that took care of it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the networking stack takes care of only notifying the routes of
interest, we do not need to maintain a list of identical routes.
Remove the check that tests if the route is the first route in the FIB
node.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix endianness issue in flowtable TCP flags dissector,
from Arnd Bergmann.
2) Extend flowtable test script with dnat rules, from Florian Westphal.
3) Reject padding in ebtables user entries and validate computed user
offset, reported by syzbot, from Florian Westphal.
4) Fix endianness in nft_tproxy, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As the LACP actor/partner state is now part of the uapi, rename the
3ad state defines with LACP prefix. The LACP prefix is preferred over
BOND_3AD as the LACP standard moved to 802.1AX.
Fixes: 826f66b30c ("bonding: move 802.3ad port state flags to uapi")
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch bringed in the "SCTP ACK tracking trace event"
feature was committed at Dec.20, 2017, it replaced jprobe usage
with trace events, and bringed in two trace events, one is
TRACE_EVENT(sctp_probe), another one is TRACE_EVENT(sctp_probe_path).
The original patch intended to trigger the trace_sctp_probe_path in
TRACE_EVENT(sctp_probe) as below code,
+TRACE_EVENT(sctp_probe,
+
+ TP_PROTO(const struct sctp_endpoint *ep,
+ const struct sctp_association *asoc,
+ struct sctp_chunk *chunk),
+
+ TP_ARGS(ep, asoc, chunk),
+
+ TP_STRUCT__entry(
+ __field(__u64, asoc)
+ __field(__u32, mark)
+ __field(__u16, bind_port)
+ __field(__u16, peer_port)
+ __field(__u32, pathmtu)
+ __field(__u32, rwnd)
+ __field(__u16, unack_data)
+ ),
+
+ TP_fast_assign(
+ struct sk_buff *skb = chunk->skb;
+
+ __entry->asoc = (unsigned long)asoc;
+ __entry->mark = skb->mark;
+ __entry->bind_port = ep->base.bind_addr.port;
+ __entry->peer_port = asoc->peer.port;
+ __entry->pathmtu = asoc->pathmtu;
+ __entry->rwnd = asoc->peer.rwnd;
+ __entry->unack_data = asoc->unack_data;
+
+ if (trace_sctp_probe_path_enabled()) {
+ struct sctp_transport *sp;
+
+ list_for_each_entry(sp, &asoc->peer.transport_addr_list,
+ transports) {
+ trace_sctp_probe_path(sp, asoc);
+ }
+ }
+ ),
But I found it did not work when I did testing, and trace_sctp_probe_path
had no output, I finally found that there is trace buffer lock
operation(trace_event_buffer_reserve) in include/trace/trace_events.h:
static notrace void \
trace_event_raw_event_##call(void *__data, proto) \
{ \
struct trace_event_file *trace_file = __data; \
struct trace_event_data_offsets_##call __maybe_unused __data_offsets;\
struct trace_event_buffer fbuffer; \
struct trace_event_raw_##call *entry; \
int __data_size; \
\
if (trace_trigger_soft_disabled(trace_file)) \
return; \
\
__data_size = trace_event_get_offsets_##call(&__data_offsets, args); \
\
entry = trace_event_buffer_reserve(&fbuffer, trace_file, \
sizeof(*entry) + __data_size); \
\
if (!entry) \
return; \
\
tstruct \
\
{ assign; } \
\
trace_event_buffer_commit(&fbuffer); \
}
The reason caused no output of trace_sctp_probe_path is that
trace_sctp_probe_path written in TP_fast_assign part of
TRACE_EVENT(sctp_probe), and it will be placed( { assign; } ) after the
trace_event_buffer_reserve() when compiler expands Macro,
entry = trace_event_buffer_reserve(&fbuffer, trace_file, \
sizeof(*entry) + __data_size); \
\
if (!entry) \
return; \
\
tstruct \
\
{ assign; } \
so trace_sctp_probe_path finally can not acquire trace_event_buffer
and return no output, that is to say the nest of tracepoint entry function
is not allowed. The function call flow is:
trace_sctp_probe()
-> trace_event_raw_event_sctp_probe()
-> lock buffer
-> trace_sctp_probe_path()
-> trace_event_raw_event_sctp_probe_path() --nested
-> buffer has been locked and return no output.
This patch is to remove trace_sctp_probe_path from the TP_fast_assign
part of TRACE_EVENT(sctp_probe) to avoid the nest of entry function,
and trigger sctp_probe_path_trace in sctp_outq_sack.
After this patch, you can enable both events individually,
# cd /sys/kernel/debug/tracing
# echo 1 > events/sctp/sctp_probe/enable
# echo 1 > events/sctp/sctp_probe_path/enable
Or, you can enable all the events under sctp.
# echo 1 > events/sctp/enable
Signed-off-by: Kevin Kou <qdkevin.kou@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The burning process requires to perform internal allocations of large
chunks of memory. This memory doesn't need to be contiguous and can be
safely allocated by vzalloc() instead of kzalloc(). This patch changes
such allocation to avoid possible out-of-memory failure.
Fixes: 410ed13cae ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we start transaction for mapping every extent for writing
using direct IO. This is unnecessary when we know we are overwriting
already allocated blocks and the overhead of starting a transaction can
be significant especially for multithreaded workloads doing small writes.
Use iomap operations that avoid starting a transaction for direct IO
overwrites.
This improves throughput of 4k random writes - fio jobfile:
[global]
rw=randrw
norandommap=1
invalidate=0
bs=4k
numjobs=16
time_based=1
ramp_time=30
runtime=120
group_reporting=1
ioengine=psync
direct=1
size=16G
filename=file1.0.0:file1.0.1:file1.0.2:file1.0.3:file1.0.4:file1.0.5:file1.0.6:file1.0.7:file1.0.8:file1.0.9:file1.0.10:file1.0.11:file1.0.12:file1.0.13:file1.0.14:file1.0.15:file1.0.16:file1.0.17:file1.0.18:file1.0.19:file1.0.20:file1.0.21:file1.0.22:file1.0.23:file1.0.24:file1.0.25:file1.0.26:file1.0.27:file1.0.28:file1.0.29:file1.0.30:file1.0.31
file_service_type=random
nrfiles=32
from 3018MB/s to 4059MB/s in my test VM running test against simulated
pmem device (note that before iomap conversion, this workload was able
to achieve 3708MB/s because old direct IO path avoided transaction start
for overwrites as well). For dax, the win is even larger improving
throughput from 3042MB/s to 4311MB/s.
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191218174433.19380-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Allow to match on vrf slave ifindex or name.
In case there was no slave interface involved, store 0 in the
destination register just like existing iif/oif matching.
sdif(name) is restricted to the ipv4/ipv6 input and forward hooks,
as it depends on ip(6) stack parsing/storing info in skb->cb[].
Cc: Martin Willi <martin@strongswan.org>
Cc: David Ahern <dsahern@kernel.org>
Cc: Shrijeet Mukherjee <shrijeet@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
skb_dst is an inline helper with a WARN_ON(), so this is a bit more code
than it looks like.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move this out of the main eval loop, the numgen expression
provides a better alternative to meta random.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reduces repetiveness and reduces size of meta eval function.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
checkpatch complains about == NULL checks in original code,
so use !in instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Not a hot path. Also, both have copy&paste case statements,
so use a common helper for both.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When pkttype is loopback, nft_meta performs guesswork to detect
broad/multicast packets. Place this in a helper, this is hardly a hot path.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
reduce size of the (large) meta evaluation function.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Make {first,last}_error_{ino,block,line,func,errcode} available via
sysfs.
Also add a missing newline for {first,last}_error_time.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This allows the cause of an ext4_error() report to be categorized
based on whether it was triggered due to an I/O error, or an memory
allocation error, or other possible causes. Most errors are caused by
a detected file system inconsistency, so the default code stored in
the superblock will be EXT4_ERR_EFSCORRUPTED.
Link: https://lore.kernel.org/r/20191204032335.7683-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The recent change to bump the ALSA control API protocol version from
2.0.7 to 2.1.0 caused a regression on user-space; while the user-space
expects both the major and the minor versions to be identical with the
supported numbers, we changed the minor number from 0 to 1.
For recovering from the incompatibility, this patch changes the
protocol version again to 2.0.8, which is compatible, but yet higher
than the original number 2.0.7, indicating that the protocol change.
Fixes: bd3eb4e87e ("ALSA: ctl: bump protocol version up to v2.1.0")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/s5h1rsr769i.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We are currently writing the same register twice. Let's enable the USB
PHY only at the end of the function.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When docked to a Motorola lapdock or media dock, we're in USB A-host mode
with VBUS provided by the dock. When in regular USB A-host mode, we're
providing the VBUS. And in regular USB A-host mode we must also keep
kicking the VBUS to keep it active.
Let's wait a bit before configuring the USB PHY to allow some time between
the ID and VBUS changes. And let's add vbus_provider flag so we can detect
docked mode and regularo USB A-host mode better.
With better USB A-host mode detection, we can now also just kick the
VBUS to keep it enabled and leave out the unnecessary line muxing.
We only need to set and clear vbus_provider in the delayed work so no
locking is needed for it currently.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The micro-USB connector on Motorola Mapphone devices can be muxed between
the SoC and the mdm6600 modem. But even when used for the SoC, configuring
the PHY with ID pin grounded will wake up the modem from idle state. Looks
like the issue is probably caused by line glitches.
We can prevent the glitches by using a previously unknown mode of the
GPIO mux to prevent the USB lines from being connected to the moden while
configuring the USB PHY, and enable the USB lines after configuring the
PHY.
Note that this only prevents waking up mdm6600 as regular USB A-host mode,
and does not help when connected to a lapdock. The lapdock specific issue
still needs to be debugged separately.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Only the used bits get cleared with bitmap_zero() when we call
gpiod_get_array_value_cansleep(). We must mask only the bits we're
using for ddata->status as the other bits in the bitmap may not be
initialized.
And let's also drop useless debug code accidentally left over while
at it.
Fixes: b9762bebc6 ("gpiolib: Pass bitmaps, not integer arrays, to get/set array")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We must let the USB host idle things properly before we switch to debug
UART mode. Otherwise the USB host may never idle after disconnecting
devices, and that causes the next enumeration to be flakey.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.
The board features:
- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver
Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add MIPI DSI pipeline for Allwinner A64.
- dsi node, with A64 compatible since it doesn't support
DSI_SCLK gating unlike A33
- dphy node, with A64 compatible with A33 fallback since
DPHY on A64 and A33 is similar
- finally, attach the dsi_in to tcon0 for complete MIPI DSI
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The MIPI DSI controller in Allwinner A64 is similar to A33.
But unlike A33, A64 doesn't have DSI_SCLK gating so add compatible
for Allwinner A64 with uninitialized has_mod_clk driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-6-jagan@amarulasolutions.com
regmap has special API to enable the controller bus clock while
initializing register space, and current driver is using
devm_regmap_init_mmio_clk which require to specify bus
clk_id argument as "bus"
But, the usage of clocks are varies between different Allwinner
DSI controllers. Clocking in A33 would need bus and mod clocks
where as A64 would need only bus clock.
Since A64 support only single bus clock, it is optional to
specify the clock-names on the controller device tree node.
So using NULL on clk_id would get the attached clock.
To support clk_id as "bus" and "NULL" during clock enablement
between controllers, this patch add generic code to handle
the bus clock using regmap_mmio_attach_clk with associated
regmap APIs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-5-jagan@amarulasolutions.com
Currently, when bpftool cgroup show <path> has an error, no error
message is printed. This is confusing because the user may think the
result is empty.
Before the change:
$ bpftool cgroup show /sys/fs/cgroup
ID AttachType AttachFlags Name
$ echo $?
255
After the change:
$ ./bpftool cgroup show /sys/fs/cgroup
Error: can't query bpf programs attached to /sys/fs/cgroup: Operation
not permitted
v2: Rename check_query_cgroup_progs to cgroup_has_attached_progs
Signed-off-by: Hechao Li <hechaol@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191224011742.3714301-1-hechaol@fb.com
As per the user manual, look like mod clock is not mandatory
for all Allwinner MIPI DSI controllers, it is connected to
CLK_DSI_SCLK for A31 and not available in A64.
So, add compatible check for A31 and get mod clock accordingly.
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-4-jagan@amarulasolutions.com
The MIPI DSI PHY controller on Allwinner A64 is similar
on the one on A31.
Add A64 compatible and append A31 compatible as fallback.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-3-jagan@amarulasolutions.com
The MIPI DSI controller in Allwinner A64 is similar to A33.
But unlike A33, A64 doesn't have DSI_SCLK gating so it is valid
to have separate compatible for A64 on the same driver.
DSI_SCLK uses mod clock-names on dt-bindings, so the same
is not required for A64.
On that note
- A64 require minimum of 1 clock like the bus clock
- A33 require minimum of 2 clocks like both bus, mod clocks
So, update dt-bindings so-that it can document both A33,
A64 bindings requirements.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222132229.30276-2-jagan@amarulasolutions.com
Clang patch [0] enables emitting relocatable generic ALU/ALU64 instructions
(i.e, shifts and arithmetic operations), as well as generic load/store
instructions. The former ones are already supported by libbpf as is. This
patch adds further support for load/store instructions. Relocatable field
offset is encoded in BPF instruction's 16-bit offset section and are adjusted
by libbpf based on target kernel BTF.
These Clang changes and corresponding libbpf changes allow for more succinct
generated BPF code by encoding relocatable field reads as a single
ST/LDX/STX instruction. It also enables relocatable access to BPF context.
Previously, if context struct (e.g., __sk_buff) was accessed with CO-RE
relocations (e.g., due to preserve_access_index attribute), it would be
rejected by BPF verifier due to modified context pointer dereference. With
Clang patch, such context accesses are both relocatable and have a fixed
offset from the point of view of BPF verifier.
[0] https://reviews.llvm.org/D71790
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191223180305.86417-1-andriin@fb.com
A64 has 3 thermal sensors: 1 for CPU, 2 for GPU.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are two sensors, one for CPU, one for GPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There is just one sensor for the CPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There are three sensors, two for each CPU cluster, one for GPU.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current descriptor is not on any list of the virtual DMA channel.
Once sdma_terminate_all() is called when a descriptor is currently
in flight then this one is forgotten to be freed. We have to call
vchan_terminate_vdesc() on this descriptor to re-add it to the lists.
Now that we also free the currently running descriptor we can (and
actually have to) remove the current descriptor from its list also
for the cyclic case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/20191216105328.15198-10-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In sdma_tx_status() we must first find the current sdma_desc. In cyclic
mode we assume that this can always be found with vchan_find_desc().
This is true because do not remove the current descriptor from the
desc_issued list:
/*
* Do not delete the node in desc_issued list in cyclic mode, otherwise
* the desc allocated will never be freed in vchan_dma_desc_free_list
*/
if (!(sdmac->flags & IMX_DMA_SG_LOOP))
list_del(&vd->node);
We will change this in the next step, so check if the current descriptor is
the desired one also for the cyclic case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20191216105328.15198-9-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rename sdma_disable_channel_async() after the hook it implements, like
done for all other functions in the SDMA driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20191216105328.15198-8-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
