The brcmu_pkt_buf_free_skb() function frees "pkt" so it leads to a
static checker warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1974 brcmf_sdio_readframes()
error: dereferencing freed memory 'pkt'
It looks like there was supposed to be a continue after we free "pkt".
Fixes: 4754fceeb9 ("brcmfmac: streamline SDIO read frame routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver expects at least one bulk-in endpoint when in "wifi-alone"
operating mode and two bulk-in endpoints otherwise, and would otherwise
fail to to submit the corresponding bulk URB to the default pipe during
probe with a somewhat cryptic message:
rsi_91x: rsi_rx_urb_submit: Failed in urb submission
rsi_91x: rsi_probe: Failed in probe...Exiting
RSI-USB WLAN: probe of 2-2.4:1.0 failed with error -8
The current endpoint sanity check looks broken and would only bail out
early if there was no bulk-in endpoint but at least one bulk-out
endpoint.
Tighten this check to always require at least one bulk-in and one
bulk-out endpoint, and add the missing sanity check for a Bluetooth
bulk-in endpoint when in a BT operating mode. Also make sure to log an
informative error message when the expected endpoints are missing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB completion handlers are called in atomic context and must
specifically not allocate memory using GFP_KERNEL.
Fixes: a1854fae14 ("rsi: improve RX packet handling in USB interface")
Cc: stable <stable@vger.kernel.org> # 4.17
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to free the skb on failed receive-URB submission (e.g. on
disconnect or currently also due to a missing endpoint).
Fixes: a1854fae14 ("rsi: improve RX packet handling in USB interface")
Cc: stable <stable@vger.kernel.org> # 4.17
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver would fail to stop the command timer in most error paths,
something which specifically could lead to the timer being freed while
still active on I/O errors during probe.
Fix this by making sure that each function starting the timer also stops
it in all relevant error paths.
Reported-by: syzbot+1d1597a5aa3679c65b9f@syzkaller.appspotmail.com
Fixes: b78e91bcfb ("rsi: Add new firmware loading method")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to stop both URBs before returning after failed probe as well
as on disconnect to avoid use-after-free in the completion handler.
Reported-by: syzbot+b563b7f8dbe8223a51e8@syzkaller.appspotmail.com
Fixes: a4302bff28 ("rsi: add bluetooth rx endpoint")
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can not set IV when we are under reset. Previously we read previous
IV value from registers and zeroed IV registers when key was deleted,
but this could possibly not work if DEL_KEY command was not performed.
Now when we have ->reconfig_complete ops and we fully mark mac80211
reset state via DEVICE_STATE_RESET flag, we can just skip setting IV
when keys are set during reset.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 has .reconfig_complete that can be used as indicator of
HW restart end. This will allow to configure keys/IV differently
for HW restart and normal configuration.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/bcma/scan.c: In function ‘bcma_erom_get_addr_desc’:
drivers/bcma/scan.c:222:20: warning: variable ‘sizel’ set but
not used [-Wunused-but-set-variable]
It is never used, and so can be removed.
Fixes: 8369ae33b7 ("bcma: add Broadcom specific AMBA bus driver")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add_ie_rates() copys rates without checking the length
in bss descriptor from remote AP.when victim connects to
remote attacker, this may trigger buffer overflow.
lbs_ibss_join_existing() copys rates without checking the length
in bss descriptor from remote IBSS node.when victim connects to
remote attacker, this may trigger buffer overflow.
Fix them by putting the length check before performing copy.
This fix addresses CVE-2019-14896 and CVE-2019-14897.
This also fix build warning of mixed declarations and code.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Wen Huang <huangwenabc@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The sband->bitrates[] array has "sband->n_bitrates" elements so this
check needs to be >= instead of > or we could read beyond the end of the
array.
These values come from when we call mt76_register_device():
ret = mt76_register_device(&dev->mt76, true, mt7603_rates,
ARRAY_SIZE(mt7603_rates));
Here sband->bitrates[] is mt7603_rates[] and ->n_bitrates is the
ARRAY_SIZE()
Fixes: 5ce09c1a79 ("mt76: track rx airtime for airtime fairness and survey")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As 'channel' is declared as u16, the following expression is always false.
channel < 0
So we can remove unnecessary 'always false' statement.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mt76_led_cleanup() function is called unconditionally, which
leads to a link error when CONFIG_LEDS is a loadable module or
disabled but mt76 is built-in:
drivers/net/wireless/mediatek/mt76/mac80211.o: In function `mt76_unregister_device':
mac80211.c:(.text+0x2ac): undefined reference to `led_classdev_unregister'
Use the same trick that is guarding the registration, using an
IS_ENABLED() check for the CONFIG_MT76_LEDS symbol that indicates
whether LEDs can be used or not.
Fixes: 36f7e2b2bb ("mt76: do not use devm API for led classdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following build warning is seen if CONFIG_PM is disabled.
drivers/usb/host/xhci-pci.c:498:13: warning:
unused function 'xhci_pci_shutdown'
Fixes: f2c710f7dc ("usb: xhci: only set D3hot for pci device")
Cc: Henry Lin <henryl@nvidia.com>
Cc: stable@vger.kernel.org # all stable releases with f2c710f7dc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191218011911.6907-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All usage of the local macros have been removed, thus the remaining
definitions are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changed macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changed macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changed macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changed macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The special macros are used in several places in the base driver.
These are replaced by standard bit manipulation macros or code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changes macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changes macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changes macros in trx.h, there are some of these
local macros in the driver. These are replaced with standard bit
manipulations. Unused macros are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
and other warnings are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The PLX PEX NTB forwards DMA transactions using Requester IDs that don't
exist as PCI devices. The devfn for a transaction is used as an index into
a lookup table storing the origin of a transaction on the other side of the
bridge.
Alias all possible devfns to the NTB device so that any transaction coming
in is governed by the mappings for the NTB.
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Add a "nr_devfns" parameter to pci_add_dma_alias() so it can be used to
create DMA aliases for a range of devfns.
[bhelgaas: incorporate nr_devfns fix from James, update
quirk_pex_vca_alias() and setup_aliases()]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The number of possible devfns is 256, but pci_add_dma_alias() allocated a
bitmap of size 255. Fix this off-by-one error.
This fixes commits 338c3149a2 ("PCI: Add support for multiple DMA
aliases") and c663579273 ("PCI: Allocate dma_alias_mask with
bitmap_zalloc()"), but I doubt it was possible to see a problem because
it takes 4 64-bit longs (or 8 32-bit longs) to hold 255 bits, and
bitmap_zalloc() doesn't save the 255-bit size anywhere.
[bhelgaas: commit log, move #define to drivers/pci/pci.h, include loop
limit fix from Qian Cai:
https://lore.kernel.org/r/20191218170004.5297-1-cai@lca.pw]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
In the implementation of brcmf_p2p_create_p2pdev() the allocated memory
for p2p_vif is leaked when the mac address is the same as primary
interface. To fix this, go to error path to release p2p_vif via
brcmf_free_vif().
Fixes: cb746e4783 ("brcmfmac: check p2pdev mac address uniqueness")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A recent addition exposed a helper that is only used for CONFIG_OF. Move
it into the CONFIG_OF zone in this file to make the compiler stop
warning about an unused function.
Fixes: 66d9506440 ("clk: walk orphan list on clock provider registration")
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: https://lkml.kernel.org/r/20191217082501.424892072D@mail.kernel.org
[sboyd@kernel.org: "Simply" move the function instead]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Whenever the signal stregth decays smoothly and physical connnection
is already gone and no deauth has arrived, the qcom soc is not
able to indicate neither WCN36XX_HAL_MISSED_BEACON_IND nor
WCN36XX_HAL_MISSED_BEACON_IND. It was noticed that such situation gets
even more reproducible, when the driver fails to enter bmps mode - which is
highly likely to occur. Thus, in order to provide proper disconnection
of the connected STA, let mac80211 handle it, instead of wcn3xx driver.
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
storage interface descriptors to avoid submitting an URB to an invalid
endpoint.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 36bcce4306 ("ath9k_htc: Handle storage devices")
Cc: stable <stable@vger.kernel.org> # 2.6.39
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit f4a73f5e26 ("pinctrl: qcom: sc7180: Add new qup functions")
has landed which means that we absolutely need to use the proper names
for the pinmuxing for I2C/UART numbers 2, 4, 7, and 9. Let's do it.
For reference:
- If you get only one of this commit and the pinctrl commit then none
of I2C/UART 2, 4, 7, and 9 will work.
- If you get neither of these commits then I2C 2, 4, 7, and 9 will
work but not UART.
...but despite the above it should be fine for this commit to land in
the Qualcomm tree because sc7180.dtsi only exists there (it hasn't
made it to mainline).
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: ba3fc64963 ("arm64: dts: sc7180: Add qupv3_0 and qupv3_1")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20191217130352.1.Id8562de45e8441cac34699047e25e7424281e9d4@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The list iterator is always non-NULL so it doesn't need to be checked.
I also removed the unnecessary initializer because the list iterator is
always initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath11k_ce_alloc_ring() function returns error pointers on error, not
NULL. The rest of the driver assumes that "pipe->src_ring" is either
valid or NULL so this patch introduces a temporary varaible to avoid
leaving it as an error pointer.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The callers unlock this lock so this error path has a double unlock.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error handling when the call to ath11k_hal_srng_get_entrysize fails
leaks skb, fix this by returning via the err_free return path that will
ensure the skb is free'd.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable radioup is not uninitalized so it may contain a garbage
value and hence the detection of a radio that is not up is buggy.
Fix this by initializing it to zero.
Addresses-Coverity: ("Uninitalized scalar variable")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently a return path is leaking the previously allocate reg_info. Fix
this by exiting via the return path mem_free. Since the return value ret
is defaulted to 0, there is no need to re-assign ret to the 0 before
the goto.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns:
drivers/net/wireless/ath/ath11k/wmi.c:1827:23: warning: implicit
conversion from enumeration type 'enum wmi_scan_priority' to different
enumeration type 'enum scan_priority' [-Wenum-conversion]
arg->scan_priority = WMI_SCAN_PRIORITY_LOW;
~ ^~~~~~~~~~~~~~~~~~~~~
1 warning generated.
wmi_scan_priority and scan_priority have the same values but the wmi one
has WMI prefixed to the names. Since that enum is already being used,
get rid of scan_priority and switch its one use to wmi_scan_priority to
fix this warning.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Link: https://github.com/ClangBuiltLinux/linux/issues/808
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several spelling mistakes in warning and debug messages,
fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
