The NXP i.MX 8QuadXPlus SOC a new ADC IP, so add
binding documentation for NXP IMX8QXP ADC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210925020555.129-3-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add
driver support for this ADC.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210925020555.129-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds ways for the SoC to wake from accelerometer wake events.
In the suspend function we skip disabling the sensor if wakeup-source
and events are activated.
If buffered reads are enabled they will be deactivated before suspend.
As the onboard buffer is only holding up to 32 12-bit X/Y/Z data
triplets.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210920114221.1595543-2-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC controller has a trimming register for fine-tune the reference
voltage. The trimming value comes from the OTP register which will be
written during chip production. This patch will read this OTP value and
configure it to the ADC register when the ADC controller probes and using
dts property "aspeed,trim-data-valid" to determine whether to execute this
flow.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-12-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In ast2600, ADC integrate dividing circuit at last input channel for
battery sensing. This patch use the dts property "battery-sensing" to
enable this feature makes the last channel of each adc can tolerance
higher voltage than reference voltage. The offset interface of ch7 will
be separated when enabling the battery sensing mode.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a compensation phase to improve the accuracy of ADC
measurement. This is the built-in function through input half of the
reference voltage to get the ADC offset.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-10-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the function to set the sampling rate and keep the sampling period
for a driver used to wait the fresh value.
In addition, since the ADC clock is required when initializing the ADC
device, move clk_prepare_enable ahead of the initialization phase.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-9-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC clock formula is
ast2400/2500:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1)
ast2600:
ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1)
They all have one fixed divided 2 and the legacy driver didn't handle it.
This patch register the fixed factory clock device as the parent of ADC
clock scaler to fix this issue.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make driver to support ast2600 adc device.
- Use shared reset controller
- Complete the vref configure function
- Add the model data for ast2600 adc
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-7-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch uses need_prescaler and scaler_bit_width to set the ADC clock
scaler.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-5-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch refactors the model data structure to distinguish the
function form different versions of aspeed ADC.
- Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data
When driver probe will check vref_fixed_mv value and store it to vref_mv
which isn't const value.
- Add num_channels
Make num_channles of iio device can be changed by different model_data
- Add need_prescaler flag and scaler_bit_width
The need_prescaler flag is used to tell the driver the clock divider needs
another Prescaler and the scaler_bit_width to set the clock divider
bitfield width.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920135413.140310-2-jacopo+renesas@jmondi.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver and device-tree also use vid-supply regulator.
Fixes: 7e000fbff7 ("dt-bindings: iio: magnetometer: ak8975: convert format to yaml, add maintainer")
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210913181949.83179-1-david@ixit.cz
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the a large chunk of data send and the receiver does not send a
Flow Control frame back in time, the sendmsg() does not return a error
code, but the number of bytes sent corresponding to the size of the
packet.
If a timeout occurs the isotp_tx_timer_handler() is fired, sets
sk->sk_err and calls the sk->sk_error_report() function. It was
wrongly expected that the error would be propagated to user space in
every case. For isotp_sendmsg() blocking on wait_event_interruptible()
this is not the case.
This patch fixes the problem by checking if sk->sk_err is set and
returning the error to user space.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://github.com/hartkopp/can-isotp/issues/42
Link: https://github.com/hartkopp/can-isotp/pull/43
Link: https://lore.kernel.org/all/20210507091839.1366379-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Reported-by: Sottas Guillaume (LMB) <Guillaume.Sottas@liebherr.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On an Intel NUC6iSYK, no IR is reported after a receive overflow.
When a receiver overflow occurs, this condition is only cleared by
reading the fifo. Make sure we read anything in the fifo.
Fixes: 28c7afb07c ("media: ite-cir: check for receive overflow")
Suggested-by: Bryan Pass <bryan.pass@gmail.com>
Tested-by: Bryan Pass <bryan.pass@gmail.com>
Cc: stable@vger.kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver is a port of the lirc_sir driver to rc-core. However, for
this driver I could not find any hardware to test, so it was done without
testing. This is a mistake.
There are clear bugs in the code. For example the two arguments
to ktime_us_delta() are reversed, which means the result is garbage.
The driver has been in the kernel for four years, and noone has ever
reported an issue. So, remove this driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
commit f0c15b360f ("media: ir_toy: prevent device from hanging during
transmit") removed a cpu_to_be16() cast, which causes a sparse warning.
Fixes: f0c15b360f ("media: ir_toy: prevent device from hanging during transmit")
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Prevent the use of page table macros and types from 2 conflicting
places. This fixes multiple build errors and warnings, e.g.:
../arch/x86/include/asm/pgtable_64_types.h:21:34: error: conflicting types for ‘pte_t’
typedef struct { pteval_t pte; } pte_t;
^~~~~
In file included from ../include/linux/mm_types_task.h:16:0,
from ../include/linux/mm_types.h:5,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/media/pci/ivtv/ivtv-driver.h:40,
from ../drivers/media/pci/ivtv/ivtvfb.c:29:
../arch/um/include/asm/page.h:57:39: note: previous declaration of ‘pte_t’ was here
typedef struct { unsigned long pte; } pte_t;
../arch/x86/include/asm/pgtable_types.h:284:43: error: expected ‘)’ before ‘prot’
static inline pgprot_t pgprot_nx(pgprot_t prot)
^
../include/linux/pgtable.h:914:26: note: in definition of macro ‘pgprot_nx’
#define pgprot_nx(prot) (prot)
^~~~
In file included from ../arch/x86/include/asm/memtype.h:6:0,
from ../drivers/media/pci/ivtv/ivtvfb.c:40:
../arch/x86/include/asm/pgtable_types.h:288:0: warning: "pgprot_nx" redefined
#define pgprot_nx pgprot_nx
../arch/x86/include/asm/page_types.h:11:0: warning: "PAGE_SIZE" redefined
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
In file included from ../include/linux/mm_types_task.h:16:0,
from ../include/linux/mm_types.h:5,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/media/pci/ivtv/ivtv-driver.h:40,
from ../drivers/media/pci/ivtv/ivtvfb.c:29:
../arch/um/include/asm/page.h:14:0: note: this is the location of the previous definition
#define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT)
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: linux-um@lists.infradead.org
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Except for VP8 probability coefficients buffer, all other buffers are
never accessed by CPU. That allows us to mark them with
DMA_ATTR_NO_KERNEL_MAPPING flag. This helps with decoding big (like 4k)
videos on 32-bit ARM platforms where default vmalloc size is relatively
small - 240 MiB. Since auxiliary buffer are not yet efficiently
allocated, this can be easily exceeded. Even if allocation is optimized,
4k videos will still often exceed this limit.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mem-to-mem stateless decoder API specifies support for dynamic
resolution changes. In particular, the decoder should accept format
changes on the OUTPUT queue even when buffers have been allocated,
as long as it is not streaming.
Relax restrictions for S_FMT as described in the previous paragraph,
and as long as the codec format remains the same. This aligns it with
the Hantro and Cedrus decoders. This change was mostly based on commit
ae02d49493 ("media: hantro: Fix s_fmt for dynamic resolution changes").
Since rkvdec_s_fmt() is now just a wrapper around the output/capture
variants without any additional shared functionality, drop the wrapper
and call the respective functions directly.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The rkvdec H.264 decoder currently overrides sizeimage for the output
format. This causes issues when userspace requires and requests a larger
buffer, but ends up with one of insufficient size.
Instead, only provide a default size if none was requested. This fixes
the video_decode_accelerator_tests from Chromium failing on the first
frame due to insufficient buffer space. It also aligns the behavior
of the rkvdec driver with the Hantro and Cedrus drivers.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Save some power by disabling/enabling the jpeg clocks with
every stream stop/start.
Do not use DL_FLAG_RPM_ACTIVE in mxc_jpeg_attach_pm_domains,
to ensure power domains are off after probe.
Signed-off-by: Mirela Rabulea <mirela.rabulea@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jeff is leaving Google so Joe will take over.
Signed-off-by: Jeff Chase <jnchase@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Confirmed to work with ADV7610 HDMI receiver.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ADV7610 is another HDMI receiver chip, very similar to
the ADV7611.
Also: print chip names in upper case.
Fix an error message claiming that no ADV761x has been found,
while in reality a chip different than requested (though still
supported) may have been found.
Tested on TinyRex BaseBoard Lite.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ADV7610 is another HDMI receiver chip, very similar to
the ADV7611. Tested on TinyRex BaseBoard Lite.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The TDA1997x (HDMI receiver) driver currently uses a specific video
format detection scheme. The frame (or field in interlaced mode), line
and HSync pulse durations are compared to those of known, standard video
modes. If a match is found, the mode is assumed to be detected,
otherwise -ERANGE is returned (then possibly ignored). This means that:
- another mode with similar timings will be detected incorrectly
(e.g. 2x faster clock and lines twice as long)
- non-standard modes will not work.
This patch replaces this scheme with a direct read of geometry
registers. This way all modes recognized by the chip are supported.
In interlaced modes, the code assumes the V sync signal has the same
duration for both fields. While this may be not necessarily true,
I can't see any way to get the "other" V sync width. This is most
probably harmless.
All tests have been performed on Gateworks' Ventana GW54xx board, with
a TDA19971 chip.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Newer clang versions are suspicious of definitions that mix concatenated
strings with comma-separated arrays of strings, this has found real bugs
elsewhere, but this seems to be a false positive:
drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:37: error: suspicious concatenation of string literals in an array initialization; did you
mean to separate the elements with a comma? [-Werror,-Wstring-concatenation]
"\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1"
^
,
drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:2: note: place parentheses around the string literal to silence warning
"\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1"
Replace the string literals by compound initializers, using normal hex numbers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Similar configuration to Kworld PC150-U.
Tested: Composite, S-Video, NTSC, ATSC
Unsupported: IR remote
Signed-off-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We need to always link allocated vb2_dc_buf back to vb2_buffer because
we dereference vb2 in prepare() and finish() callbacks.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
I came across a link failure from randconfig builds:
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove':
ths8200.c:(.text+0x491): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe':
ths8200.c:(.text+0xe49): undefined reference to `v4l2_async_register_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_remove':
tw9910.c:(.text+0x467): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_probe':
tw9910.c:(.text+0x1123): undefined reference to `v4l2_async_register_subdev'
These clearly lack a 'select' statement, but I don't know why
this started happening only now. I had a bit of a look around to find
other configs that have the same problem, but could not come up with
a reliable way and found nothing else through experimentation.
It is likely that other symbols like these exist that need an extra
select.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adding kfree(dvb) to vidtv_bridge_remove() will remove the memory
too soon: if an application still has an open filehandle to the device
when the driver is unloaded, then when that filehandle is closed, a
use-after-free access takes place to the freed memory.
Move the kfree(dvb) to vidtv_bridge_dev_release() instead.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 76e21bb8be ("media: vidtv: Fix memory leak in remove")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most interesting element this time is the new chrdev based interface
for the counter subsystem. Affects all drivers. Some minor precursor
patches.
Major parts:
* Bring all the sysfs attribute setup into the counter core rather than
leaving it to individual drivers. Docs updates accompany these changes.
* Move various definitions to a uapi header as now needed from userspace.
* Add the chardev interface + extensive documentation and example tool
* Add new ABI needed to identify indexes needed for chrdev interface
* Implement new interface for the 104-quad-8
* Follow up deals with wrong path for documentation build
* Various trivial cleanups and missing feature additions related to this
series
-----BEGIN PGP SIGNATURE-----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=AaeD
-----END PGP SIGNATURE-----
Merge tag 'counter-for-5.16a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of counter subsystem new feature support for the 5.16 cycle
Most interesting element this time is the new chrdev based interface
for the counter subsystem. Affects all drivers. Some minor precursor
patches.
Major parts:
* Bring all the sysfs attribute setup into the counter core rather than
leaving it to individual drivers. Docs updates accompany these changes.
* Move various definitions to a uapi header as now needed from userspace.
* Add the chardev interface + extensive documentation and example tool
* Add new ABI needed to identify indexes needed for chrdev interface
* Implement new interface for the 104-quad-8
* Follow up deals with wrong path for documentation build
* Various trivial cleanups and missing feature additions related to this
series
* tag 'counter-for-5.16a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
docs: counter: Include counter-chrdev kernel-doc to generic-counter.rst
counter: fix docum. build problems after filename change
counter: microchip-tcb-capture: Tidy up a false kernel-doc /** marking.
counter: 104-quad-8: Add IRQ support for the ACCES 104-QUAD-8
counter: 104-quad-8: Replace mutex with spinlock
counter: Implement events_queue_size sysfs attribute
counter: Implement *_component_id sysfs attributes
counter: Implement signalZ_action_component_id sysfs attribute
tools/counter: Create Counter tools
docs: counter: Document character device interface
counter: Add character device interface
counter: Move counter enums to uapi header
docs: counter: Update to reflect sysfs internalization
counter: Update counter.h comments to reflect sysfs internalization
counter: Internalize sysfs interface code
counter: stm32-timer-cnt: Provide defines for slave mode selection
counter: stm32-lptimer-cnt: Provide defines for clock polarities
Add a mapping for my old work email for BelDisplayTech to the personal
email, and make sure the Collabora email has the correct spelling of the
first name.
Link: https://lkml.kernel.org/r/20210917091016.30232-1-andrew.shadura@collabora.co.uk
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Decrease nr_thps counter in file's mapping to ensure that the page cache
won't be dropped excessively on file write access if page has been
already split.
I've tried a test scenario running a big binary, kernel remaps it with
THPs, then force a THP split with /sys/kernel/debug/split_huge_pages.
During any further open of that binary with O_RDWR or O_WRITEONLY kernel
drops page cache for it, because of non-zero thps counter.
Link: https://lkml.kernel.org/r/20211012120237.2600-1-m.szyprowski@samsung.com
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09d91cda0e ("mm,thp: avoid writes to file with THP in pagecache")
Fixes: 06d3eff62d ("mm/thp: fix node page state in split_huge_page_to_list()")
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: <sfoon.kim@samsung.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we open a file without read access and then pass the fd to a syscall
whose implementation calls kernel_read_file_from_fd(), we get a warning
from __kernel_read():
if (WARN_ON_ONCE(!(file->f_mode & FMODE_READ)))
This currently affects both finit_module() and kexec_file_load(), but it
could affect other syscalls in the future.
Link: https://lkml.kernel.org/r/20211007220110.600005-1-willy@infradead.org
Fixes: b844f0ecbc ("vfs: define kernel_copy_file_from_fd()")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reported-by: Hao Sun <sunhao.th@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 6e7b64b9dd ("elfcore: fix building with clang") introduces
special handling for two architectures, ia64 and User Mode Linux.
However, the wrong name, i.e., CONFIG_UM, for the intended Kconfig
symbol for User-Mode Linux was used.
Although the directory for User Mode Linux is ./arch/um; the Kconfig
symbol for this architecture is called CONFIG_UML.
Luckily, ./scripts/checkkconfigsymbols.py warns on non-existing configs:
UM
Referencing files: include/linux/elfcore.h
Similar symbols: UML, NUMA
Correct the name of the config to the intended one.
[akpm@linux-foundation.org: fix um/x86_64, per Catalin]
Link: https://lkml.kernel.org/r/20211006181119.2851441-1-catalin.marinas@arm.com
Link: https://lkml.kernel.org/r/YV6pejGzLy5ppEpt@arm.com
Link: https://lkml.kernel.org/r/20211006082209.417-1-lukas.bulwahn@gmail.com
Fixes: 6e7b64b9dd ("elfcore: fix building with clang")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Barret Rhoden <brho@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When sysfs_slab_add failed, we shouldn't call debugfs_slab_add() for s
because s will be freed soon. And slab_debugfs_fops will use s later
leading to a use-after-free.
Link: https://lkml.kernel.org/r/20210916123920.48704-5-linmiaohe@huawei.com
Fixes: 64dd68497b ("mm: slub: move sysfs slab alloc/free interfaces to debugfs")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Faiyaz Mohammed <faiyazm@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In error path, the random_seq of slub cache might be leaked. Fix this
by using __kmem_cache_release() to release all the relevant resources.
Link: https://lkml.kernel.org/r/20210916123920.48704-4-linmiaohe@huawei.com
Fixes: 210e7a43fa ("mm: SLUB freelist randomization")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Faiyaz Mohammed <faiyazm@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
