Send a TEST UNIT READY to HBA disks and do not present them to the OS if
0x02/0x04/0x1b (SANITIZE IN PROGRESS) is returned.
During boot-up, some OSes appear to hang when there are one or more disks
undergoing a sanitize operation.
According to SCSI SBC4 specification section 4.11.2 "Commands allowed
during SANITIZE", some SCSI commands are permitted, but read/write
operations are not.
When the OS attempts to read the disk partition table a CHECK CONDITION ASC
0x04 ASCQ 0x1b is returned which causes the OS to retry the read until
SANITIZE has completed. This can take hours.
According to document HPE Smart Storage Administrator User Guide, during
the sanitize erase operation, the drive is unusable. I.e. the expected
behavior for SANITIZE is the that disk remains offline even after SANITIZE
has completed. The customer is expected to re-enable the disk using the
management utility.
Link: https://lore.kernel.org/r/20210928235442.201875-6-don.brace@microchip.com
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhance check for commands queued to the controller. Add new function
pqi_nonempty_inbound_queue_count() that will wait for all I/O queued for
submission to controller across all queue groups to drain. Add helper
functions to obtain queue command counts for each queue group. These
queues should drain quickly as they are already staged to be submitted down
to the controller's IB queue.
Enhance check for outstanding command completion. Update the count of
outstanding commands while waiting. This value was not re-obtained and was
potentially causing infinite wait for all completions.
Link: https://lore.kernel.org/r/20210928235442.201875-5-don.brace@microchip.com
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some rare cases, the driver can halt the controller. Add a reason code
describing why the controller was halted. Store this reason code in a
controller register to aid in debugging the issue.
Link: https://lore.kernel.org/r/20210928235442.201875-4-don.brace@microchip.com
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct kdump hangs when controller is locked up.
There are occasions when a controller reboot (controller soft reset) is
issued when a controller firmware crash dump is in progress.
This leads to incomplete controller firmware crash dump:
- When the controller crash dump is in progress, and a kdump is initiated,
the driver issues inbound doorbell reset to bring back the controller in
SIS mode.
- If the controller is in locked up state, the inbound doorbell reset does
not work causing controller initialization failures. This results in the
driver hanging waiting for SIS mode.
To avoid an incomplete controller crash dump, add in a controller crash
dump handshake:
- Controller will indicate start and end of the controller crash dump by
setting some register bits.
- Driver will look these bits when a kdump is initiated. If a controller
crash dump is in progress, the driver will wait for the controller crash
dump to complete before issuing the controller soft reset then complete
driver initialization.
Link: https://lore.kernel.org/r/20210928235442.201875-3-don.brace@microchip.com
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update device removal path to handle issues for:
- rmmod: Correct stack trace when removing devices.
- rmmod: Synchronize SCSI cache.
- Update handling for removing devices using sysfs.
Link: https://lore.kernel.org/r/20210928235442.201875-2-don.brace@microchip.com
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This function is more complicated than necessary.
If we change from scnprintf() to snprintf() that lets us remove the if
bytes_wrote < sizeof(protocol) checks. Also, we can use bytes_wrote ? ","
: "" to print the comma and remove the separate if statement and the
"is_string_nonempty" variable.
[mkp: a few formatting cleanups and s/wrote/written/]
Link: https://lore.kernel.org/r/20210916132605.GF25094@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit d39df15851 ("scsi: iscsi: Have abort handler get ref to conn")
added iscsi_get_conn()/iscsi_put_conn() calls during abort handling but
then also changed the handling of the case where we detect an already
completed task where we now end up doing a goto to the common put/cleanup
code. This results in a iscsi_task use after free, because the common
cleanup code will do a put on the iscsi_task.
This reverts the goto and moves the iscsi_get_conn() to after we've checked
if the iscsi_task is valid.
Link: https://lore.kernel.org/r/20211004210608.9962-1-michael.christie@oracle.com
Fixes: d39df15851 ("scsi: iscsi: Have abort handler get ref to conn")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an FC-GS I/O is aborted by lpfc, the driver requires a node pointer
for a dereference operation. In the abort I/O routine, the driver miscasts
a context pointer to the wrong data type and overwrites a single byte
outside of the allocated space. This miscast is done in the abort I/O
function handler because the handler works on both FC-GS and FC-LS
commands. However, the code neglected to get the correct job location for
the node.
Fix this by acquiring the necessary node pointer from the correct job
structure depending on the I/O type.
Link: https://lore.kernel.org/r/20211004231210.35524-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's not holding the lock at this stage and the IRQ "flags" are not correct
so it would restore something bogus. Delete the unlock statement.
Link: https://lore.kernel.org/r/20211004103851.GE25015@kili
Fixes: 3e6414003b ("scsi: elx: efct: SCSI I/O handling routines")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pm8001_mpi_get_nvmd_resp() handles a GET_NVMD_DATA response, not a
SET_NVMD_DATA response, as the log statement implies.
Fixes: 1f889b5871 ("scsi: pm80xx: Fix pm8001_mpi_get_nvmd_resp() race condition")
Link: https://lore.kernel.org/r/20210929025847.646999-1-ipylypiv@google.com
Reviewed-by: Changyuan Lyu <changyuanl@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a follow up cleanup to the commit 924a3541ea ("scsi: libsas:
aic94xx: hisi_sas: mvsas: pm8001: Use dev_is_expander()")
Link: https://lore.kernel.org/r/20210929025807.646589-1-ipylypiv@google.com
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make use of the struct_size() helper instead of an open-coded version, in
order to avoid any potential type mistakes or integer overflows that, in
the worst scenario, could lead to heap overflows.
Link: https://github.com/KSPP/linux/issues/160
Link: https://lore.kernel.org/r/20210927224344.GA190701@embeddedor
Reviewed-by: Bodo Stroesser <bostroesser@gmail.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many fabric modules provide their own implementation of enable attribute in
tpg.
Provide a way to remove code duplication in the fabric modules and
automatically add "enable" attribute if a fabric module has an
implementation of fabric_enable_tpg().
Link: https://lore.kernel.org/r/20210910084133.17956-2-d.bogdanov@yadro.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a device tree for a Colibri iMX6ULL 1GB which has a eMMC instead of
the raw NAND used on other SKUs.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add toradex,colibri-imx6ull-emmc for our new Colibri iMX6ULL 1GB (eMMC)
Module and the carrier boards (so far only Colibri Evaluation Board) it
may be mated in.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IRQ polling thread calls ISR after enable_irq() to handle any missed I/O
completion. The atomic flag "in_used" was added to have the synchronization
between the IRQ polling thread and the interrupt context. There is a bug
around it leading to a race condition.
Below is the sequence:
- IRQ polling thread accesses ISR, fetches the reply descriptor.
- Real interrupt arrives and pre-empts polling thread (enable_irq() is
already called).
- Interrupt context picks the same reply descriptor as fetched by polling
thread, processes it, and exits.
- Polling thread resumes and processes the descriptor which is already
processed by interrupt thread leads to kernel crash.
Setting the "in_used" flag before fetching the reply descriptor ensures
synchronized access to ISR.
Link: https://www.spinics.net/lists/linux-scsi/msg159440.html
Link: https://lore.kernel.org/r/20210929124022.24605-2-sumit.saxena@broadcom.com
Fixes: 9bedd36e91 ("scsi: megaraid_sas: Handle missing interrupts while re-enabling IRQs")
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable CONFIG_BPF_SYSCALL and CONFIG_CGROUP_BPF to allow for systemd
interoperability. This avoids the following failure on boot:
[ 10.615914] systemd[1]: system-getty.slice: unit configures an IP
firewall, but the local system does not support BPF/cgroup firewalling.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Build CONFIG_IMX_SDMA as a module to avoid the following boot issue:
[ 5.214751] imx-sdma 20ec000.sdma: Direct firmware load for
imx/sdma/sdma-imx6q.bin failed with error -2
[ 5.215762] imx-sdma 20ec000.sdma: Falling back to sysfs fallback
for: imx/sdma/sdma-imx6q.bin
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Run "make imx_v6_v7_defconfig; make savedefconfig" to rebuild
imx_v6_v7_defconfig.
This dropped the following nowadays obsolete configuration options:
CONFIG_MTD_M25P80=y (got integrated into MTD_SPI_NOR)
CONFIG_CS89x0=y (selected by CS89x0_PLATFORM)
CONFIG_SMSC_PHY=y (selected by USB_NET_SMSC95XX)
CONFIG_GPIO_MC9S08DZ60=y (depends on MACH_MX35_3DS)
CONFIG_REGULATOR=y (selected by various stuff)
CONFIG_MEDIA_CAMERA_SUPPORT=y (defaults to on if MEDIA_CAMERA)
CONFIG_MEDIA_CONTROLLER=y (selected by various stuff)
CONFIG_VIDEO_V4L2_SUBDEV_API=y (selected by various stuff)
CONFIG_SND_SOC_PHYCORE_AC97=y
CONFIG_SND_SOC_IMX_MC13783=y
CONFIG_USB_EHCI_MXC=y
CONFIG_USB_FSL_USB2=y
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change CONFIG_SND_SOC_TLV320AIC3X to CONFIG_SND_SOC_TLV320AIC3X_I2C.
I did double check all current mainline device trees and they are all
using the I2C rather than the SPI variant.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pointers should be printed with %p or %px rather than cast to 'unsigned
long' and printed with %lx.
Change %lx to %p to print the hashed pointer.
Link: https://lore.kernel.org/r/20210929122538.1158235-1-qtxuning1999@sjtu.edu.cn
Signed-off-by: Guo Zhi <qtxuning1999@sjtu.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the log level of the following message to debug:
Unsupported SCSI Opcode 0xXX, sending CHECK_CONDITION.
This message is mostly helpful during debugging sessions in order to
understand errors on the initiator side. But most of the time it's just
useless and makes reading logs much harder.
It gets particularly annoying if there are many initiators that come and go
or if an initiator runs a program that does not care whether the command is
supported and just keeps sending it.
Link: https://lore.kernel.org/r/20210929114959.705852-1-k.shelekhin@yadro.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Konstantin Shelekhin <k.shelekhin@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Callers of ufshcd_err_handler() expect it to return in an operational
state. However, the code does not check the state before exiting.
Add a check for the state and perform retries until either success or the
maximum number of retries is reached.
Link: https://lore.kernel.org/r/20211002154550.128511-3-adrian.hunter@intel.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Callers of ufshcd_reset_and_restore() expect it to return in an operational
state. However, the code only checks direct errors and so the ufshcd_state
may not be UFSHCD_STATE_OPERATIONAL due to error interrupts.
Fix by also checking ufshcd_state, still allowing non-fatal errors which
are left for the error handler to deal with.
Link: https://lore.kernel.org/r/20211002154550.128511-2-adrian.hunter@intel.com
Reviewed-by: Avri altman <avri.altman@wdc.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit aa53f580e6 ("scsi: ufs: Minor adjustments to error handling")
introduced a ufshcd_clear_ua_wluns() call in
ufshcd_err_handling_unprepare(). As explained in detail by Adrian Hunter,
this can trigger a deadlock. Avoid that deadlock by removing the code that
clears the unit attention. This is safe because the only software that
relies on clearing unit attentions is the Android Trusty software and
because support for handling unit attentions has been added in the Trusty
software.
See also https://lore.kernel.org/linux-scsi/20210930124224.114031-2-adrian.hunter@intel.com/
Note that "scsi: ufs: Retry START_STOP on UNIT_ATTENTION" is a prerequisite
for this commit.
Link: https://lore.kernel.org/r/20211001182015.1347587-3-jaegeuk@kernel.org
Fixes: aa53f580e6 ("scsi: ufs: Minor adjustments to error handling")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 57d104c153 ("ufs: add UFS power management support") made the UFS
driver submit a REQUEST SENSE command before submitting a power management
command to a WLUN to clear the POWER ON unit attention. Instead of
submitting a REQUEST SENSE command before submitting a power management
command, retry the power management command until it succeeds.
This is the preparation to get rid of all UNIT ATTENTION code which should
be handled by users.
Link: https://lore.kernel.org/r/20211001182015.1347587-2-jaegeuk@kernel.org
Cc: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 568dd99596 ("scsi: ufs: Rename the second ufshcd_probe_hba()
argument"), the second ufshcd_probe_hba() argument has been changed to
init_dev_params.
Link: https://lore.kernel.org/r/20210929200640.828611-3-huobean@gmail.com
Fixes: 568dd99596 ("scsi: ufs: Rename the second ufshcd_probe_hba() argument")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS driver uses blk_mq_tagset_busy_iter() when identifying task
management requests to complete, however blk_mq_tagset_busy_iter() doesn't
work.
blk_mq_tagset_busy_iter() only iterates requests dispatched by the block
layer. That appears as if it might have started since commit 37f4a24c24
("blk-mq: centralise related handling into blk_mq_get_driver_tag") which
removed 'data->hctx->tags->rqs[rq->tag] = rq' from blk_mq_rq_ctx_init()
which gets called:
blk_get_request
blk_mq_alloc_request
__blk_mq_alloc_request
blk_mq_rq_ctx_init
Since UFS task management requests are not dispatched by the block layer,
hctx->tags->rqs[rq->tag] remains NULL, and since blk_mq_tagset_busy_iter()
relies on finding requests using hctx->tags->rqs[rq->tag], UFS task
management requests are never found by blk_mq_tagset_busy_iter().
By using blk_mq_tagset_busy_iter(), the UFS driver was relying on internal
details of the block layer, which was fragile and subsequently got
broken. Fix by removing the use of blk_mq_tagset_busy_iter() and having the
driver keep track of task management requests.
Link: https://lore.kernel.org/r/20210922091059.4040-1-adrian.hunter@intel.com
Fixes: 1235fc569e ("scsi: ufs: core: Fix task management request completion timeout")
Fixes: 69a6c269c0 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Cc: stable@vger.kernel.org
Tested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 756fb6a895 ("scsi: acornscsi: Remove tagged queuing vestiges")
mistakenly introduced a reference to function scsi_cmd_to_tag(). This
function does not exist as it was removed from an earlier series version
when I upstreamed the named commit - originally authored By Hannes - but
this reference still remained.
Fix by replacing the reference to scsi_cmd_to_tag() with
scsi_cmd_to_rq(scsi_scmd)->tag, which scsi_cmd_to_tag() was a wrapper for.
Link: https://lore.kernel.org/r/1633002717-79765-1-git-send-email-john.garry@huawei.com
Fixes: 756fb6a895 ("scsi: acornscsi: Remove tagged queuing vestiges")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The typo in this source code comment makes the comment confusing. Clear up
the confusion by fixing the typo.
Link: https://lore.kernel.org/r/20210929182318.2060489-1-bvanassche@acm.org
Fixes: bc85dc500f ("scsi: remove scsi_end_request")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prior to this patch the driver requires two IRQs to function properly,
one required IRQ for control and at least one required IRQ for IO.
This requirement can be relaxed to one as the driver now allows
sharing of IRQs, so control and IO EQs can share the same irq.
This is needed for high scale amount of VFs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Control IRQ is the first IRQ vector. This complicates handling of
completion irqs as we need to offset them by one.
in the next patch, there are scenarios where completion and control EQs
will share the same irq. for example: functions with single IRQ. To ease
such scenarios, we shift control IRQ to the end of the irq array.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Create lowest priority flow group in egress table with single rule that
matches on special reg_c1 value that is set on ingress VLAN push with
single action that pops VLAN. The flow destination is skip table that is
used to skip any further processing of packet in FDB bridge priority.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
On ingress VLAN push also assign value 0x7FE to reg_c1 tunnel id+opts
bits (tunnel id 0, which is not a valid tunnel id, and option 0x7FE which
was reserved by one of previous patches in the series). In following patch
the reg value is matched on egress miss to restore the packet to its
original state by removing the VLAN before passing it to the software data
path.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in series need to pop VLAN when packet misses on egress.
To reuse existing bridge VLAN pop handling code, extract it to dedicated
helpers mlx5_esw_bridge_pkt_reformat_vlan_pop_supported() and
mlx5_esw_bridge_pkt_reformat_vlan_pop_create().
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Several functions in bridge.c excessively obtain pointer to parent eswitch
instance by dereferencing br_offloads->esw on every usage and following
patches in this series add even more usages of eswitch. Introduce local
variable 'esw' and use it instead.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Support TC generic 'accept' action in mlx5 by introducing
MLX5_ESW_ATTR_FLAG_ACCEPT attribute flag. Flag has similar semantics to
existing MLX5_ESW_ATTR_FLAG_SLOW_PATH flag, however, dedicated flag is
required because existing 'slow path' flag can be flipped by tunneling
subsystem when neighbor changes state.
Introduce new helper function mlx5_esw_attr_flags_skip() to check whether
attribute flags for 'slow path' or 'accept' action are set and use it in
eswitch code instead of direct bit manipulation.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
