The DP spec says:
"If the receiver keeps the same value in the ADJUST_REQUEST_LANEx_y
register(s) while the LANEx_CR_DONE bits remain unset, the transmitter
must loop four times with the same voltage swing. On the fifth time,
the transmitter must down-shift to the lower bit rate and must repeat
the CR-lock training sequence as described below."
Lets fix the code to follow that instead of terminating after five
times of transmitting the same signal levels. The text in spec feels
a little bit ambiguous still, but this is my best guess at its meaning.
As a bonus this also gets rid of the train_set[0] stuff which
would not work for per-lane drive settings anyway.
Cc: Imre Deak <imre.deak@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001160826.17080-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The name "tty" is typically used for pointers to struct tty_struct.
Rename the tty-driver pointer used during registration to something more
apt to improve readability.
Acked-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210917114622.5412-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PROC_FS is not set, there is a build warning (turned
into an error):
../drivers/hwmon/dell-smm-hwmon.c: In function 'i8k_init_procfs':
../drivers/hwmon/dell-smm-hwmon.c:624:24: error: unused variable 'data' [-Werror=unused-variable]
struct dell_smm_data *data = dev_get_drvdata(dev);
Make I8K depend on PROC_FS and HWMON (instead of selecting HWMON -- it
is strongly preferred to not select entire subsystems).
Build tested in all possible combinations of SENSORS_DELL_SMM, I8K, and
PROC_FS.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lkml.kernel.org/r/20210910071921.16777-1-rdunlap@infradead.org
Elements of the 'names' array are not changed by the code, constify them
for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Using the generic extension from the previous patch, a specific multisync
extension enables more than one in/out binary syncobj per job submission.
Arrays of syncobjs are set in struct drm_v3d_multisync, that also cares
of determining the stage for sync (wait deps) according to the job
queue.
v2:
- subclass the generic extension struct (Daniel)
- simplify adding dependency conditions to make understandable (Iago)
v3:
- fix conditions to consider single or multiples in/out_syncs (Iago)
- remove irrelevant comment (Iago)
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ffd8b2e3dd2e0c686db441a0c0a4a0181ff85328.1633016479.git.mwen@igalia.com
Add support to attach generic extensions on job submission. This patch
is third prep work to enable multiple syncobjs on job submission. With
this work, when the job submission interface needs to be extended to
accommodate a new feature, we will use a generic extension struct where
an id determines the data type to be pointed. The first application is
to enable multiples in/out syncobj (next patch), but the base is
already done for future features. Therefore, to attach a new feature,
a specific extension struct should subclass drm_v3d_extension and
update the list of extensions in a job submission.
v2:
- remove redundant elements to subclass struct (Daniel)
v3:
- add comment for v3d_get_extensions
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ed53b1cd7e3125b76f18fe3fb995a04393639bc6.1633016479.git.mwen@igalia.com
Move job memory allocation to v3d_job_init function. This aim to facilitate
error handling in job initialization, since cleanup steps are similar for
all (struct v3d_job)-based types of job involved in a command submission.
To generalize v3d_job_init(), this change takes into account that all job
structs have the first element a struct v3d_job (bin, render, tfu, csd) or
it is a v3d_job itself (clean_job) for pointer casting.
v3:
- explicitly init job as NULL (Iago)
- fix pm failure handling on v3_job_init (Iago)
Suggested-by: Iago Toral Quiroga <itoral@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4d12e07bd334d2cddb51cabd359e99edde595619.1633016479.git.mwen@igalia.com
When CONFIG_PRINTK is not set, the CMPXCHG_BUGCHECK() macro calls
_printk(), but _printk() is a static inline function, not available
as an extern.
Since the purpose of the macro is to print the BUGCHECK info,
make this config option depend on PRINTK.
Fixes multiple occurrences of this build error:
../include/linux/printk.h:208:5: error: static declaration of '_printk' follows non-static declaration
208 | int _printk(const char *s, ...)
| ^~~~~~~
In file included from ../arch/ia64/include/asm/cmpxchg.h:5,
../arch/ia64/include/uapi/asm/cmpxchg.h:146:28: note: previous declaration of '_printk' with type 'int(const char *, ...)'
146 | extern int _printk(const char *fmt, ...);
Cc: linux-ia64@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Fix the following W=1 kernel build warning:
kernel/printk/printk.c: In function 'printk_sprint':
kernel/printk/printk.c:1913:9: warning: function 'printk_sprint' might be
a candidate for 'gnu_printf' format attribute [-Wsuggest-attribute=format]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210927142203.124730-1-john.ogness@linutronix.de
clang notices that the pi_get_entry() function would use
uninitialized data if it was called with a non-NULL module
pointer on a kernel that does not support modules:
kernel/printk/index.c:32:6: error: variable 'nr_entries' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
if (!mod) {
^~~~
kernel/printk/index.c:38:13: note: uninitialized use occurs here
if (pos >= nr_entries)
^~~~~~~~~~
kernel/printk/index.c:32:2: note: remove the 'if' if its condition is always true
if (!mod) {
Rework the condition to make it clear to the compiler that we are always
in the second case. Unfortunately the #ifdef is still required as the
definition of 'struct module' is hidden when modules are disabled.
Fixes: 3370155737 ("printk: Userspace format indexing support")
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210928093456.2438109-1-arnd@kernel.org
It's been reported that doing stress test for module insertion and
removal can result in an ENOENT from libkmod for a valid module.
In kernfs_iop_lookup() a negative dentry is created if there's no kernfs
node associated with the dentry or the node is inactive.
But inactive kernfs nodes are meant to be invisible to the VFS and
creating a negative dentry for these can have unexpected side effects
when the node transitions to an active state.
The point of creating negative dentries is to avoid the expensive
alloc/free cycle that occurs if there are frequent lookups for kernfs
attributes that don't exist. So kernfs nodes that are not yet active
should not result in a negative dentry being created so when they
transition to an active state VFS lookups can create an associated
dentry is a natural way.
It's also been reported that https://github.com/osandov/blktests.git
test block/001 hangs during the test. It was suggested that recent
changes to blktests might have caused it but applying this patch
resolved the problem without change to blktests.
Fixes: c7e7c04274 ("kernfs: use VFS negative dentry caching")
Tested-by: Yi Zhang <yi.zhang@redhat.com>
ACKed-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ian Kent <raven@themaw.net>
Link: https://lore.kernel.org/r/163330943316.19450.15056895533949392922.stgit@mickey.themaw.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial/uart support for NXP S32G2 based on the information provided by
NXP's CodeAurora BSP.
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: Chester Lin <clin@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an initial dtsi file for generic SoC features of NXP S32G2.
Signed-off-by: Chester Lin <clin@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a compatible string for the uart binding of NXP S32G2 platforms. Here
we use "s32v234-linflexuart" as fallback since the current linflexuart
driver can still work on S32G2.
Signed-off-by: Chester Lin <clin@suse.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Convert the FSL LINFlexD UART binding to json-schema.
Signed-off-by: Chester Lin <clin@suse.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To bring up the MX8MM GPU domain, it is necessary to configure both
GPC_PGC_nCTRL(GPU_2D) and GPC_PGC_nCTRL(GPU_3D) registers. Without
this configuration, the system might hang on boot when bringing up
the GPU power domain. This is sporadically observed on multiple
disparate systems.
Add the GPU3D bit into MX8MM GPU domain pgc bitfield, so that both
GPC_PGC_nCTRL(GPU_2D) and GPC_PGC_nCTRL(GPU_3D) registers are
configured when bringing up the GPU domain. This fixes the sporadic
hang.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is currently the MX8MM GPU domain, which is in fact a composite domain
for both GPU2D and GPU3D. To correctly configure this domain, it is necessary
to control both GPC_PGC_nCTRL(GPU_2D) and GPC_PGC_nCTRL(GPU_3D) at the same
time. This is currently not possible.
Turn the domain->pgc from value into bitfield and use for_each_set_bit() to
iterate over all bits set in domain->pgc when configuring GPC_PGC_nCTRL
register array. This way it is possible to configure all GPC_PGC_nCTRL
registers required in a particular domain.
This is a preparatory patch, no functional change.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210927220232.1071926-7-mcgrof@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Link: https://lore.kernel.org/r/20210927220232.1071926-6-mcgrof@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Be sure to call dasd_gendisk_free() on error.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210927220232.1071926-5-mcgrof@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The memory for amode31 section is allocated from the decompressed
kernel. Instead, allocate that memory from the decompressor. This
is a prerequisite to allow initialization of the virtual memory
before the decompressed kernel takes over.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Partially revert commit 4555b9f34296 ("s390/boot: move
dma sections from decompressor to decompressed kernel").
This is a prerequisite to allow initialization of virtual
memory in decompressor and avoid overwriting of ASCEs in
the decompressed kernel otherwise.
Since the control registers 2, 5 and 15 are reinitialized
in the decompressed kernel again, this change does not
prevent relocating of amode31 section in any way.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When CONFIG_SCLP_VT220_TTY=y and CONFIG_SCLP_VT220_CONSOLE is not set:
../drivers/s390/char/sclp_vt220.c:771:13: warning: '__sclp_vt220_flush_buffer' defined but not used [-Wunused-function]
771 | static void __sclp_vt220_flush_buffer(void)
so move this function inside the #ifdef block where it is used.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Link: https://lore.kernel.org/r/20210927215647.11506-1-rdunlap@infradead.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add a few testcases to make sure that it's not possible to place
a kprobe in the mid of an instruction on s390.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
FTRACE_GEN_NOP_ASM(name) can be used to generate assembly functions with
the required information added to allow tracing via kprobes/ftrace. It
adds the nop instruction which will be patched by ftrace later. If the
compiler supports -mnop-mcount it will also add an entry to the
__mcount_loc section.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Fix these warnings that are reported when compiling with W=1:
drivers/s390/char/sclp_sd.c:132: warning: Function parameter or member 'listener' not described in 'sclp_sd_listener_init'
drivers/s390/char/sclp_sd.c:408: warning: Function parameter or member 'cookie' not described in 'sclp_sd_file_update_async'
drivers/s390/char/sclp_sd.c:422: warning: Function parameter or member 'attr' not described in 'reload_store'
drivers/s390/char/sclp_sd.c:422: warning: Function parameter or member 'buf' not described in 'reload_store'
drivers/s390/char/sclp_sd.c:422: warning: Function parameter or member 'count' not described in 'reload_store'
drivers/s390/char/sclp_sd.c:457: warning: Function parameter or member 'file' not described in 'data_read'
drivers/s390/char/sclp_sd.c:457: warning: Function parameter or member 'attr' not described in 'data_read'
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
cdev->online for the purge function must not be checked for the
non-IO subchannel type. Make sure that we are deriving the cdev only
from sch-type SUBCHANNEL_TYPE_IO.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
We often need to figure out what operations were performed in response
to an error or availability event. The operations are easily accessible
in s390dbf/pci_msg but the events have to be correlated with these from
either the kernel log or s390dbf/pci_err. Improve this situation by
logging the most important data from error and availability events that
is the FID, PEC and FH together with the operations.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The cio_ignore list is used to create and maintain the list of devices
which is to be ignored by Linux. During boot-time, this list is adjusted
and accommodate all the devices which are configured on the HMC
interface. Once these devices are accessible, they are then available to
Linux and set online.
cio_ignore purge function should align with this functionality. But
currently, the subchannel associated with the offline-devices are not
unregistered during purge. Add an explicit subchannel-unregister function
in the purge_fn callback.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since commit 8256adda1f ("s390/pci: handle FH state mismatch only on
disable") zpci_disable_device() returns -EINVAL when the platform
detects an attempt to disable a PCI function that it sees as already
disabled.
In most situations we want to abort whenever this happens and abort is
possible since it either means that the device vanished but we haven't
gotten an availability event yet, or the FH got out of sync which should
not happen.
Unfortunately there is an inconsistency between the LPAR and z/VM
hypervisors on whether error events for PCI functions contain an
an enabled or a general handle. So under z/VM it can happen that our
most up to date function handle is enabled but trying to disable the
function results in the aforementioned error.
Since recover is designed to be used to recover functions from the error
state let's make it robust to this inconsistency by explicitly treating
it as a successful disable.
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Check whether the specified address points to the start of an
instruction to prevent users from setting a kprobe in the mid of
an instruction which would crash the kernel.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
ftrace_shared_hotpatch_trampoline() never returns NULL,
therefore quite a bit of code can be removed.
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since commit 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
the reference count of a zpci_dev is incremented between
pcibios_add_device() and pcibios_release_device() which was supposed to
prevent the zpci_dev from being freed while the common PCI code has
access to it. It was missed however that the handling of zPCI
availability events assumed that once zpci_zdev_put() was called no
later availability event would still see the device. With the previously
mentioned commit however this assumption no longer holds and we must
make sure that we only drop the initial long-lived reference the zPCI
subsystem holds exactly once.
Do so by introducing a zpci_device_reserved() function that handles when
a device is reserved. Here we make sure the zpci_dev will not be
considered for further events by removing it from the zpci_list.
This also means that the device actually stays in the
ZPCI_FN_STATE_RESERVED state between the time we know it has been
reserved and the final reference going away. We thus need to consider it
a real state instead of just a conceptual state after the removal. The
final cleanup of PCI resources, removal from zbus, and destruction of
the IOMMU stays in zpci_release_device() to make sure holders of the
reference do see valid data until the release.
Fixes: 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Make sure to free jit_data through kfree() in the error path.
Fixes: 1c8f9b91c4 ("bpf: s390: add JIT support for multi-function programs")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This applies a SND_PCI_QUIRK(...) to the Clevo X170KM-G barebone. This
fixes the issue of the devices internal Speaker not working.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211001133111.428249-3-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The string "Clevo X170" is not enough to unambiguously identify the correct
device.
Fixing it so another Clevo barebone name starting with "X170" can be added
without causing confusion.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211001133111.428249-2-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Prevent memset of ioctl arguments in case driver returns -EINTR
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE7TEboABC71LctBLFZR1NuKta54AFAmFUMUUACgkQZR1NuKta
54DliwgAi1Hy9BLNGm3Otu3vFNdaqgDI2RR/pgxWS4qb6UOmkYePfsX+3ShaVucv
ujIuURgLILlZtABL+erxFn/zKPiBLsThChTzX2oBStVxVPaYkEgGmzxmjBbjCwjm
bteh3yxdl69RfW2ZLsHrC3oI7GZOFS7l+XhYj5RRfBAq04KOahoMVlGnm8m5Y3MS
umRI+bIU3m+qMKZGTnQQQVp/IJW8ManvBu0AF0paq+yaYKVPojCdP8VVRCyQM3iB
+uR83lcgPdQbPC7N0cVZKJ4RYERD3rVDD5Egabqir8S6ehP/69K4ixT15JtlojCA
ekLvfKje2LO/ThsY2hICCVO3hUWq1g==
=qEeo
-----END PGP SIGNATURE-----
Merge tag 'misc-habanalabs-fixes-2021-09-29' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux into char-misc-linus
Oded writes:
This tag contains the following fix for 5.15-rc4:
- Prevent memset of ioctl arguments in case driver returns -EINTR
* tag 'misc-habanalabs-fixes-2021-09-29' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux:
habanalabs: fix resetting args in wait for CS IOCTL
The return value from tegra_bpmp_transfer indicates the success or
failure of the IPC transaction with BPMP. If the transaction
succeeded, we also need to check the actual command's result code.
Add code to do this.
While at it, explicitly handle missing CPU clusters, which can
occur on floorswept chips. This worked before as well, but
possibly only by accident.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
list cpu_data_list has been inited staticly through LIST_HEAD,
so there's no need to call another INIT_LIST_HEAD. Simply remove
it from cppc_cpufreq_init.
Signed-off-by: Han Wang <zjuwanghan@outlook.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
