Commit graph

1,058,063 commits

Author SHA1 Message Date
Ajay Singh
aa3fda4fcf wilc1000: ignore clockless registers status response for SPI
During WILC chip wake-up sequence, the clockless status register sometimes
reports failure even when the actual status is successful. So, for the
clockless register, remove the incorrect error status reporting during the
read and write command API's.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-8-ajay.kathat@microchip.com
2021-09-21 18:08:16 +03:00
Ajay Singh
c2dcb4766b wilc1000: handle read failure issue for clockless registers
For SPI bus, the register read fails after read/write to the clockless
register during chip wakeup sequence. Add workaround to send CMD_RESET
command during chip wake-up sequence to overcome the issue.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-7-ajay.kathat@microchip.com
2021-09-21 18:08:16 +03:00
Ajay Singh
1bcc0879c9 wilc1000: add reset/terminate/repeat command support for SPI bus
Add reset/terminate/repeat command for SPI module. In case of SPI commands
failure, the host should issue a RESET command to WILC chip to recover
from any temporary bus error.
For now, the new command support is added and later the SPI read/write
API's would be modified to make use of these commands for retry mechanism

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-6-ajay.kathat@microchip.com
2021-09-21 18:08:16 +03:00
Ajay Singh
5bb9de8bcb wilc1000: configure registers to handle chip wakeup sequence
Use the correct sequence to configure clockless registers for chip wake-up.
The following sequence is expected from WILC chip for wakeup:
 - set wakeup bit in wakeup_reg register
 - after setting the wakeup bit, read back the clock status bit for wakeup
   complete.

For SDIO/SPI modules, the wakeup sequence is the same except uses different
register values so refactored the code to use common function for both
SDIO/SPI bus.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-5-ajay.kathat@microchip.com
2021-09-21 18:08:15 +03:00
Ajay Singh
0ec5408cd4 wilc1000: add new WID to pass wake_enable information to firmware
Add new WID(WID_WOWLAN_TRIGGER) to send wake_enable information to firmware.
In 'set_wakeup' cfg80211_ops callback, the enable information was not
passed to firmware which is required to handle WOWLan trigger notification
from firmware.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-4-ajay.kathat@microchip.com
2021-09-21 18:08:15 +03:00
Ajay Singh
3c719fed0f wilc1000: fix possible memory leak in cfg_scan_result()
When the BSS reference holds a valid reference, it is not freed. The 'if'
condition is wrong. Instead of the 'if (bss)' check, the 'if (!bss)' check
is used.
The issue is solved by removing the unnecessary 'if' check because
cfg80211_put_bss() already performs the NULL validation.

Fixes: 6cd4fa5ab6 ("staging: wilc1000: make use of cfg80211_inform_bss_frame()")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-3-ajay.kathat@microchip.com
2021-09-21 18:08:14 +03:00
Ajay Singh
c8e2036ee9 wilc1000: move 'deinit_lock' lock init/destroy inside module probe
Move initialization & deinitialization of 'deinit_lock' mutex lock inside
wlan_init_locks() & wlan_deinit_locks() API's respectively alongside other
locks. After the movement, the client count variable(client_count) which is
used for lock init/deinit is removed.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-2-ajay.kathat@microchip.com
2021-09-21 18:08:14 +03:00
Marek Vasut
31f97cf9f0 rsi: Fix module dev_oper_mode parameter description
The module parameters are missing dev_oper_mode 12, BT classic alone,
add it. Moreover, the parameters encode newlines, which ends up being
printed malformed e.g. by modinfo, so fix that too.

However, the module parameter string is duplicated in both USB and SDIO
modules and the dev_oper_mode mode enumeration in those module parameters
is a duplicate of macros used by the driver. Furthermore, the enumeration
is confusing.

So, deduplicate the module parameter string and use __stringify() to
encode the correct mode enumeration values into the module parameter
string. Finally, replace 'Wi-Fi' with 'Wi-Fi alone' and 'BT' with
'BT classic alone' to clarify what those modes really mean.

Fixes: 898b255339 ("rsi: add module parameter operating mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: Martin Fuzzey <martin.fuzzey@flowbird.group>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: netdev@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.17+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916144245.10181-1-marex@denx.de
2021-09-21 18:03:48 +03:00
Jonas Dreßler
72e717500f mwifiex: Fix copy-paste mistake when creating virtual interface
The BSS priority here for a new P2P_CLIENT device was accidentally set
to an enum that's certainly not meant for this. Since
MWIFIEX_BSS_ROLE_STA is 0 anyway, we can just set the bss_priority to 0
instead here.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-10-verdre@v0yd.nl
2021-09-21 18:02:19 +03:00
Jonas Dreßler
c606008b70 mwifiex: Properly initialize private structure on interface type changes
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.

When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.

This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
2021-09-21 18:02:18 +03:00
Jonas Dreßler
5e2e1a4bf4 mwifiex: Handle interface type changes from AP to STATION
Looks like this case was simply overseen, so handle it, too.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-8-verdre@v0yd.nl
2021-09-21 18:02:18 +03:00
Jonas Dreßler
25bbec30a2 mwifiex: Allow switching interface type from P2P_CLIENT to P2P_GO
It's possible to change virtual interface type between P2P_CLIENT and
P2P_GO, the card supports that just fine, and it happens for example
when using miracast with the miraclecast software.

So allow type changes between P2P_CLIENT and P2P_GO and simply call into
mwifiex_change_vif_to_p2p(), which handles this just fine. We have to
call mwifiex_cfg80211_deinit_p2p() before though to make sure the old
p2p mode is properly uninitialized.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-7-verdre@v0yd.nl
2021-09-21 18:02:18 +03:00
Jonas Dreßler
fae2aac8c7 mwifiex: Update virtual interface counters right after setting bss_type
In mwifiex_init_new_priv_params() we update our private driver state to
reflect the currently selected virtual interface type. Most notably we
set the bss_mode to the mode we're going to put the firmware in.

Now after we updated the driver state we actually start talking to the
firmware and instruct it to set up the new mode. Those commands can and
will sometimes fail, in which case we return with an error from
mwifiex_change_vif_to_*. We currently update our virtual interface type
counters after this return, which means the code is never reached when a
firmware error happens and we never update the counters. Since we have
updated our bss_mode earlier though, the counters now no longer reflect
the actual state of the driver.

This will break things on the next virtual interface change, because the
virtual interface type we're switching away from didn't get its counter
incremented, and we end up decrementing a 0-counter.

To fix this, simply update the virtual interface type counters right
after updating our driver structures, so that they are always in sync.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-6-verdre@v0yd.nl
2021-09-21 18:02:17 +03:00
Jonas Dreßler
54350dac4e mwifiex: Use helper function for counting interface types
Use a small helper function to increment and decrement the counter of
the interface types we currently manage. This makes the code that
actually changes and sets up the interface type a bit less messy and
also helps avoiding mistakes in case someone increments/decrements a
counter wrongly.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-5-verdre@v0yd.nl
2021-09-21 18:02:17 +03:00
Jonas Dreßler
c2e9666cdf mwifiex: Run SET_BSS_MODE when changing from P2P to STATION vif-type
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.

Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.

This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
2021-09-21 18:02:17 +03:00
Jonas Dreßler
abe3a2c9ea mwifiex: Use function to check whether interface type change is allowed
Instead of bailing out in the function which is supposed to do the type
change, detect invalid changes beforehand using a generic function and
return an error if the change is not allowed.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-3-verdre@v0yd.nl
2021-09-21 18:02:16 +03:00
Jonas Dreßler
babe2a332d mwifiex: Small cleanup for handling virtual interface type changes
Handle the obvious invalid virtual interface type changes with a general
check instead of looking at the individual change.

For type changes from P2P_CLIENT to P2P_GO and the other way round, this
changes the behavior slightly: We now still do nothing, but return
-EOPNOTSUPP instead of 0. Now that behavior was incorrect before and
still is, because type changes between these two types are actually
possible and supported, which we'll fix in a following commit.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-2-verdre@v0yd.nl
2021-09-21 18:02:16 +03:00
Chin-Yen Lee
fe7bc23a8c rtw88: move adaptivity mechanism to firmware
Current adaptivity mechanism is achieved in driver, by periodically
referencing the IGI value and then updating related registers.
But we find that this way may halt TX activity too long if huge
and temporary energy is detected frequently. So we move the mechanism
to firmware for immediately reacting this case to recover TX rapidly.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-5-pkshih@realtek.com
2021-09-21 17:51:57 +03:00
Zong-Zhe Yang
7285eb9693 rtw88: support adaptivity for ETSI/JP DFS region
Add Energy Detected CCA (EDCCA) mechanism to detect energy on the channel.
And EDCCA support adaptivity mode now. From MIC Ordinance Regulating Radio
Equipment article 49.20, ETSI EN-300-328 and EN-301-893, the device should
be able to dynamically pause TX activity when energy detected on the air.
According to ETSI/JP DFS region, driver will set corresponding threshold
and stop TX activity if the detected energy exceeds the threshold. For now,
we support it on 8822b and 8822c first.

By default, EDCCA mechanism is turned on. For ETSI/JP DFS region, it will
turn to adaptivity mode. However, with adaptivity, if environment is too
noisy, TX may often be halted. So, a debugfs for EDCCA is added. It can
show what EDCCA mode is used currently. And EDCCA mechanism can be turned
on/off through the debugfs while debugging.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-4-pkshih@realtek.com
2021-09-21 17:51:56 +03:00
Zong-Zhe Yang
8d4fb3998c rtw88: add regulatory strategy by chip type
Realtek chips can program a specific country domain on efuse to
indicate what is the expected rtw_regulatory. For chips with a
programmed country domain, we set REGULATORY_STRICT_REG to tell
stack to consider follow-up regulatory_hint() as the superset of
our regulatory rule. Besides, on driver side, only the request via
NL80211_REGDOM_SET_BY_DRIVER, which matches programmed country
domain, will be handled to keep rtw_regulatory unchanged.

For worldwide roaming chips, i.e. ones without a specific programmed
country domain, system of distro can set expected regulatory via
NL80211_REGDOM_SET_BY_USER. With setting from it, rtw_regulatory
will handle the requests only via NL80211_REGDOM_SET_BY_USER to
follow setting from system of distro. REGULATORY_COUNTRY_IE_IGNORE
will then be set to tell stack to ignore country IE for us. The
restrictions mentioned above will remain until 00, i.e. worldwide,
is set via NL80211_REGDOM_SET_BY_USER.

On the other hand, for worldwide roamin chips, if there is no
specific regulatory set via NL80211_REGDOM_SET_BY_USER, requests
from all regulatory notifications will be handled by rtw_regulatory.
And REGULATORY_COUNTRY_IE_IGNORE won't be set.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-3-pkshih@realtek.com
2021-09-21 17:51:56 +03:00
Zong-Zhe Yang
f8509c38ec rtw88: upgrade rtw_regulatory mechanism and mapping
Mapping table from country code to rtw_regulatory, which manages tx power
limit according to countries, is updated. And mapping architecture is also
upgraded. For more precise control on tx power limit, it allows different
rtw_regulatory for different bands logically. Besides, a helper function
to query rtw_regulatory for current band under current country is provided.

For older chips, some newly added rtw_regulatory may not be configured.
To avoid that those chips have no limit on some countries mapping to a
newer rtw_regulatory after table update, a backward selection mechanism
of rtw_regulatory is introduced. It can help chips use a rtw_regulatory
which has been configured as an alternative of a newer one which is not
configured.

In addition, rtw88 actually doesn't manage channel plans by itself.
Instead, it follows them from stack. So, correct some naming about
chplan with regd, and remove the unnecessary channel control for now.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-2-pkshih@realtek.com
2021-09-21 17:51:56 +03:00
Dan Carpenter
517c7bf99b usb: musb: tusb6010: uninitialized data in tusb_fifo_write_unaligned()
This is writing to the first 1 - 3 bytes of "val" and then writing all
four bytes to musb_writel().  The last byte is always going to be
garbage.  Zero out the last bytes instead.

Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210916135737.GI25094@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:38:21 +02:00
Ondrej Zary
b55d37ef6b usb-storage: Add quirk for ScanLogic SL11R-IDE older than 2.6c
ScanLogic SL11R-IDE with firmware older than 2.6c (the latest one) has
broken tag handling, preventing the device from working at all:
usb 1-1: new full-speed USB device number 2 using uhci_hcd
usb 1-1: New USB device found, idVendor=04ce, idProduct=0002, bcdDevice= 2.60
usb 1-1: New USB device strings: Mfr=1, Product=1, SerialNumber=0
usb 1-1: Product: USB Device
usb 1-1: Manufacturer: USB Device
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi host2: usb-storage 1-1:1.0
usbcore: registered new interface driver usb-storage
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd

Add US_FL_BULK_IGNORE_TAG to fix it. Also update my e-mail address.

2.6c is the only firmware that claims Linux compatibility.
The firmware can be upgraded using ezotgdbg utility:
https://github.com/asciilifeform/ezotgdbg

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210913210106.12717-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:37:52 +02:00
Julian Sikorski
ce1c42b4da Re-enable UAS for LaCie Rugged USB3-FW with fk quirk
Further testing has revealed that LaCie Rugged USB3-FW does work with
uas as long as US_FL_NO_REPORT_OPCODES and US_FL_NO_SAME are enabled.

Link: https://lore.kernel.org/linux-usb/2167ea48-e273-a336-a4e0-10a4e883e75e@redhat.com/
Cc: stable <stable@vger.kernel.org>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Julian Sikorski <belegdol+github@gmail.com>
Link: https://lore.kernel.org/r/20210913181454.7365-1-belegdol+github@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:37:26 +02:00
Wesley Cheng
8217f07a50 usb: dwc3: gadget: Avoid starting DWC3 gadget during UDC unbind
There is a race present where the DWC3 runtime resume runs in parallel
to the UDC unbind sequence.  This will eventually lead to a possible
scenario where we are enabling the run/stop bit, without a valid
composition defined.

Thread#1 (handling UDC unbind):
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
  -->dwc3_gadget_pullup(0)
--> continue UDC unbind sequence
-->Thread#2 is running in parallel here

Thread#2 (handing next cable connect)
__dwc3_set_mode()
  -->pm_runtime_get_sync()
    -->dwc3_gadget_resume()
      -->dwc->gadget_driver is NOT NULL yet
      -->dwc3_gadget_run_stop(1)
      --> _dwc3gadget_start()
...

Fix this by tracking the pullup disable routine, and avoiding resuming
of the DWC3 gadget.  Once the UDC is re-binded, that will trigger the
pullup enable routine, which would handle enabling the DWC3 gadget.

Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210917021852.2037-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:35:03 +02:00
Sergey Shtylyov
a8426a43b0 usb: core: hcd: fix messages in usb_hcd_request_irqs()
Two dev_info() calls in usb_hcd_request_irqs() mistreat the I/O port base
address, calling it just "io base" instead of "io port".

While fixing this, make indenataion of the argument lists more sane...

Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/5d10014d-e58b-d081-ed7c-7424f649ce0b@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:34:14 +02:00
Krzysztof Kozlowski
dfa59f3d4c usb: host: ehci-mv: drop duplicated MODULE_ALIAS
There is one MODULE_ALIAS already.

Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210916170531.138335-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:33:00 +02:00
Linus Walleij
41b086b22f ARM: dts: ux500: Skomer eMMC needs 300 ms power on
The partitions on the eMMC will not even appear sometimes, in the
datasheet for the Samsung KLMxGxxE4x we find that the power-on time
for a 4GB eMMC of this type is 300 ms and nowadays the block stack
is so fast so we are stressing it, and we need to specify that we
need this delay in the device tree.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-09-21 16:32:03 +02:00
Linus Walleij
1a4c270554 ARM: dts: ux500: Fix up SD card pin config
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-09-21 16:32:03 +02:00
Linus Walleij
7aee0288be ARM: dts: ux500: Skomer regulator fixes
AUX2 has slightly wrong voltage and AUX5 doesn't need to be
always on.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-09-21 16:32:03 +02:00
Sven Peter
b7a0a63f3f usb: typec: tipd: Remove WARN_ON in tps6598x_block_read
Calling tps6598x_block_read with a higher than allowed len can be
handled by just returning an error. There's no need to crash systems
with panic-on-warn enabled.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20210914140235.65955-3-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:31:28 +02:00
Sven Peter
ac588dfa66 usb: typec: tipd: Add an additional overflow check
tps6598x_block_read already checks for the maximum length of the read
but tps6598x_block_write does not. Add the symmetric check there as
well.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20210914140235.65955-2-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:31:28 +02:00
Sven Peter
718dccb477 usb: typec: tipd: Don't read/write more bytes than required
tps6598x_block_read/write always read 65 bytes of data even when much
less is required when I2C_FUNC_I2C is used. Reduce this to the correct
number.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20210914140235.65955-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:31:27 +02:00
Yang Yingliang
14651496a3 usb: musb: tusb6010: check return value after calling platform_get_resource()
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210915034925.2399823-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:26:49 +02:00
Apurva Nandan
d7a48e27b3
spi: Use 'flash' node name instead of 'spi-flash' in example
Change the nodename in the example with spi-nand from 'spi-flash@1'
to 'flash@1' to make the schema uniform with both spi-nand and spi-nor
flashes. jedec,spi-nor.yaml uses 'flash@' nodename for spi-nor flashes,
so make the spi-nand examples in dt-bindings use it too for uniformity.

Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920142713.129295-3-a-nandan@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-21 15:25:10 +01:00
Krzysztof Kozlowski
c03d369952 USB: cdc-acm: remove duplicate USB device ID
The device 0x00e9 (Nokia 5320 XpressMusic) is already on the list.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210917091849.18692-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:24:16 +02:00
Mark Brown
66ae258ccf
Merge branch 'spi-5.15' into spi-5.16 2021-09-21 15:23:50 +01:00
Mark Brown
ffb1e76f4f Linux 5.15-rc2
-----BEGIN PGP SIGNATURE-----
 
 iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmFH1aYeHHRvcnZhbGRz
 QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG8OkH/R6C6xduJ7I/LkUK
 S3bATqOwAnpR8Z/1cbNIj7NG7wFEiRbOS0xgnxteUgo34xGVWUoRgdM2wvi4mnst
 fvWsM/8765g4ok5WtmxZ+ZeClVFo2eGWyZqfsXMlisPNwswceSPOXDPMcEKlROZA
 CGFqCh0hmma3+waAKf85ZfFR8i/gndbI574MKq00OPNr02Z8GSqQMJSaCzNbGspc
 AMpdXezEG6CnwRUnlmYZoXOBP9+/ItAMZ6RTPulitJKT3PmuHcs9Pnu6qqbW2X9B
 fRW3tQNE5Q4oLHPb7H9m13jMNwuIP4DI3b3qnUSjl0g4OKBX0q/Uw1UfntC5Ejxn
 9d7jvZ8=
 =6RN4
 -----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmFJ6ukACgkQJNaLcl1U
 h9AwcAf/W8ESV6W8ZzsgIaI+waCk5xB55g1RdF6GzXlLKq30Va/i/12Lgc0xmUvL
 FEfQ9h63oBLB2KR3lUmztofCm8bN9bBTCYGJUnJh/z/vfXN8Av1TJdfGUBIbjcCE
 UNS4Fr6oE2PGDzleJNnE23GULpOYWg4ITzTC5TVkTlXkuUqmx2EZjQGkpBWz/Y3z
 6vpk1wm9XJZxbU4hh3eA3pQkDbSdVHSAZnlEZudxJyuOj0JSJHLgqwDIkO7spy/v
 V/WQIsfeqEkFPfCkPciodSHpl1XMxU5qdVC2wo11skRhHOHLwlVrOn2TcpvY7tq7
 qEstYJfaLGVoGpzu4Cv9Eu+BzEOVNA==
 =Czel
 -----END PGP SIGNATURE-----

Merge tag 'v5.15-rc2' into spi-5.15

Linux 5.15-rc2
2021-09-21 15:23:35 +01:00
Johan Hovold
d9d1232b48 misc: bcm-vk: fix tty registration race
Make sure to set the tty class-device driver data before registering the
tty to avoid having a racing open() dereference a NULL pointer.

Fixes: 91ca10d6fa ("misc: bcm-vk: add ttyVK support")
Cc: stable@vger.kernel.org      # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210917115736.5816-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:17:15 +02:00
Christophe JAILLET
5e87622c4b misc: genwqe: Remove usage of the deprecated "pci-dma-compat.h" API
In [1], Christoph Hellwig has proposed to remove the wrappers in
include/linux/pci-dma-compat.h.

Some reasons why this API should be removed have been given by Julia
Lawall in [2].

Finally, Arnd Bergmann reminded that the documentation was updated 11 years
ago to only describe the modern linux/dma-mapping.h interfaces and mark the
old bus-specific ones as no longer recommended, see commit 216bf58f40
("Documentation: convert PCI-DMA-mapping.txt to use the generic DMA API").

A coccinelle script has been used to perform the needed transformation
Only relevant parts are given below.

@@ @@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL@@

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

[1]: https://lore.kernel.org/kernel-janitors/20200421081257.GA131897@infradead.org/
[2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.2007120902170.2424@hadrien/

Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/590154f2ab113088346ae76c3f13f8b1cbebccbb.1631942274.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-09-21 16:15:57 +02:00
Benson Leung
5135b21392
MAINTAINERS: Add Prashant's maintainership of cros_ec drivers
Prashant maintains the cros_usbpd_notify driver as well as
the cros_ec_type_c driver.

Link: https://lore.kernel.org/r/20210920205402.3818320-1-bleung@chromium.org
Signed-off-by: Benson Leung <bleung@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2021-09-21 07:12:10 -07:00
Colin Ian King
b5377a7678
ASoC: qdsp6: q6afe-dai: Fix spelling mistake "Fronend" -> "Frontend"
There is a spelling mistake in the module description. Fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210920184152.18109-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-09-21 15:03:33 +01:00
Robin Murphy
59a68d4138 arm64: Mitigate MTE issues with str{n}cmp()
As with strlen(), the patches importing the updated str{n}cmp()
implementations were originally developed and tested before the
advent of CONFIG_KASAN_HW_TAGS, and have subsequently revealed
not to be MTE-safe. Since in-kernel MTE is still a rather niche
case, let it temporarily fall back to the generic C versions for
correctness until we can figure out the best fix.

Fixes: 758602c044 ("arm64: Import latest version of Cortex Strings' strcmp")
Fixes: 020b199bc7 ("arm64: Import latest version of Cortex Strings' strncmp")
Cc: <stable@vger.kernel.org> # 5.14.x
Reported-by: Branislav Rankov <branislav.rankov@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/34dc4d12eec0adae49b0ac927df642ed10089d40.1631890770.git.robin.murphy@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2021-09-21 14:50:19 +01:00
Tobias Jakobi
6f6aab1caf platform/x86: gigabyte-wmi: add support for B550I Aorus Pro AX
Tested with a AMD Ryzen 7 5800X.

Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Thomas Weißschuh <thomas@weissschuh.net>
Link: https://lore.kernel.org/r/20210921100702.3838-1-tjakobi@math.uni-bielefeld.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2021-09-21 15:49:23 +02:00
José Expósito
b201cb0ebe platform/x86/intel: hid: Add DMI switches allow list
Some devices, even non convertible ones, can send incorrect
SW_TABLET_MODE reports.

Add an allow list and accept such reports only from devices in it.

Bug reported for Dell XPS 17 9710 on:
https://gitlab.freedesktop.org/libinput/libinput/-/issues/662

Reported-by: Tobias Gurtzick <magic@wizardtales.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Tobias Gurtzick <magic@wizardtales.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20210920160312.9787-1-jose.exposito89@gmail.com
[hdegoede@redhat.com: Check dmi_switches_auto_add_allow_list only once]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2021-09-21 15:49:16 +02:00
Randy Dunlap
5b72dafaca platform/x86: dell: fix DELL_WMI_PRIVACY dependencies & build error
When DELL_WMI=y, DELL_WMI_PRIVACY=y, and LEDS_TRIGGER_AUDIO=m, there
is a linker error since the LEDS trigger code is built as a loadable
module. This happens because DELL_WMI_PRIVACY is a bool that depends
on a tristate (LEDS_TRIGGER_AUDIO=m), which can be dangerous.

ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe':
dell-wmi-privacy.c:(.text+0x3df): undefined reference to `ledtrig_audio_get'

Fixes: 8af9fa37b8 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Perry Yuan <Perry.Yuan@dell.com>
Cc: Dell.Client.Kernel@dell.com
Cc: platform-driver-x86@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20210918044829.19222-1-rdunlap@infradead.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2021-09-21 15:49:09 +02:00
Bryan O'Donoghue
0e159d2c08 wcn36xx: Implement Idle Mode Power Save
Idle Mode Power Save (IMPS) is a power saving mechanism which when called
by wcn36xx will cause the radio hardware to enter power collapse.

This particular call maps nicely to a simple conjunction/disjunction around
IEEE80211_CONF_CHANGE_IDLE and IEEE80211_CONF_IDLE.

Here we enter idle when we are not associated with an AP. The kernel will
incrementally toggle idle on/off in the process of trying to establish a
connection, thus saving power until we are connected to the AP again, at
which point we give way to BMPS if power_save is on.

We've validated that with IMPS an apq8039 device which has the wcn36xx
module loaded but, has not authenticated with an AP will get to VMIN on
suspend and will not without IMPS.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909153320.2624649-1-bryan.odonoghue@linaro.org
2021-09-21 16:34:32 +03:00
Bryan O'Donoghue
c0c2eb20c7 wcn36xx: Add ability for wcn36xx_smd_dump_cmd_req to pass two's complement
Qcom documents suggest passing of negative values to the dump command,
however currently we convert from string to u32 not s32, so we cannot pass
a two's complement value to the firmware in this way.

There is in fact only one parameter which takes a two's complement value
<tigger threshold> in the antenna diversity switch command.

Downstream:
iwpriv wlan0 dump 71 3 <schedule period> <trigger threshold> <hysteresis value>

Upstream:
echo "71 3 <schedule period> <trigger threshold> <hysteresis value>" > /sys/kernel/debug/ieee80211/phy0/wcn36xx/dump

Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-3-bryan.odonoghue@linaro.org
2021-09-21 16:33:25 +03:00
Bryan O'Donoghue
701668d3bf wcn36xx: Fix Antenna Diversity Switching
We have been tracking a strange bug with Antenna Diversity Switching (ADS)
on wcn3680b for a while.

ADS is configured like this:
   A. Via a firmware configuration table baked into the NV area.
       1. Defines if ADS is enabled.
       2. Defines which GPIOs are connected to which antenna enable pin.
       3. Defines which antenna/GPIO is primary and which is secondary.

   B. WCN36XX_CFG_VAL(ANTENNA_DIVERSITY, N)
      N is a bitmask of available antenna.

      Setting N to 3 indicates a bitmask of enabled antenna (1 | 2).

      Obviously then we can set N to 1 or N to 2 to fix to a particular
      antenna and disable antenna diversity.

   C. WCN36XX_CFG_VAL(ASD_PROBE_INTERVAL, XX)
      XX is the number of beacons between each antenna RSSI check.
      Setting this value to 50 means, every 50 received beacons, run the
      ADS algorithm.

   D. WCN36XX_CFG_VAL(ASD_TRIGGER_THRESHOLD, YY)
      YY is a two's complement integer which specifies the RSSI decibel
      threshold below which ADS will run.
      We default to -60db here, meaning a measured RSSI <= -60db will
      trigger an ADS probe.

   E. WCN36XX_CFG_VAL(ASD_RTT_RSSI_HYST_THRESHOLD, Z)
      Z is a hysteresis value, indicating a delta which the RSSI must
      exceed for the antenna switch to be valid.

      For example if HYST_THRESHOLD == 3 AntennaId1-RSSI == -60db and
      AntennaId-2-RSSI == -58db then firmware will not switch antenna.
      The threshold needs to be -57db or better to satisfy the criteria.

   F. A firmware feature bit also exists ANTENNA_DIVERSITY_SELECTION.
      This feature bit is used by the firmware to report if
      ANTENNA_DIVERSITY_SELECTION is supported. The host is not required to
      toggle this bit to enable or disable ADS.

ADS works like this:

    A. Every XX beacons the firmware switches to or remains on the primary
       antenna.

    B. The firmware then sends a Request-To-Send (RTS) packet to the AP.

    C. The firmware waits for a Clear-To-Send (CTS) response from the AP.

    D. The firmware then notes the received RSSI on the CTS packet.

    E. The firmware then repeats steps A-D on the secondary antenna.

    F. Subsequently if the RSSI on the measured antenna is better than
       ASD_TRIGGER_THRESHOLD + the active antenna's RSSI then the
       measured antenna becomes the active antenna.

    G. If RSSI rises past ASD_TRIGGER_THRESHOLD then ADS doesn't run at
       all even if there is a substantially better RSSI on the alternative
       antenna.

What we have been observing is that the RTS packet is being sent but the
MAC address is a byte-swapped version of the target MAC. The ADS/RTS MAC is
corrupted only when the link is encrypted, if the AP is open the RTS MAC is
correct. Similarly if we configure the firmware to an RTS/CTS sequence for
regular data - the transmitted RTS MAC is correctly formatted.

Internally the wcn36xx firmware uses the indexes in the SMD commands to
populate and extract data from specific entries in an STA lookup table. The
AP's MAC appears a number of times in different indexes within this lookup
table, so the MAC address extracted for the data-transmit RTS and the MAC
address extracted for the ADS/RTS packet are not the same STA table index.

Our analysis indicates the relevant firmware STA table index is
"bssSelfStaIdx".

There is an STA populate function responsible for formatting the MAC
address of the bssSelfStaIdx including byte-swapping the MAC address.

Its clear then that the required STA populate command did not run for
bssSelfStaIdx.

So taking a look at the sequence of SMD commands sent to the firmware we
see the following downstream when moving from an unencrypted to encrypted
BSS setup.

- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_CONFIG_STA_REQ
- WLAN_HAL_SET_STAKEY_REQ

Upstream in wcn36xx we have

- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_SET_STAKEY_REQ

The solution then is to add the missing WLAN_HAL_CONFIG_STA_REQ between
WLAN_HAL_CONFIG_BSS_REQ and WLAN_HAL_SET_STAKEY_REQ.

No surprise WLAN_HAL_CONFIG_STA_REQ is the routine responsible for
populating the STA lookup table in the firmware and once done the MAC sent
by the ADS routine is in the correct byte-order.

This bug is apparent with ADS but it is also the case that any other
firmware routine that depends on the "bssSelfStaIdx" would retrieve
malformed data on an encrypted link.

Fixes: 3e977c5c52 ("wcn36xx: Define wcn3680 specific firmware parameters")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-2-bryan.odonoghue@linaro.org
2021-09-21 16:33:24 +03:00
Benjamin Li
d6dbce453b wcn36xx: handle connection loss indication
Firmware sends delete_sta_context_ind when it detects the AP has gone
away in STA mode. Right now the handler for that indication only handles
AP mode; fix it to also handle STA mode.

Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210901180606.11686-1-benl@squareup.com
2021-09-21 16:31:41 +03:00