Aux hardware calibration sequence requires resetting the aux controller
in order for the new setting to take effect. However resetting the AUX
controller will also clear HPD interrupt status which may accidentally
cause pending unplug interrupt to get lost. Therefore reset aux
controller only when link is in connection state when dp_aux_cmd_fifo_tx()
fail. This fixes Link Layer CTS cases 4.2.1.1 and 4.2.1.2.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1628196295-7382-4-git-send-email-khsieh@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reduce link rate and re start link training if link training 1
failed due to loss of clock recovery done to fix Link Layer
CTS case 4.3.1.7. Also only update voltage and pre-emphasis
swing level after link training started to fix Link Layer CTS
case 4.3.1.6.
Changes in V2:
-- replaced cr_status with link_status[DP_LINK_STATUS_SIZE]
-- replaced dp_ctrl_any_lane_cr_done() with dp_ctrl_colco_recovery_any_ok()
-- replaced dp_ctrl_any_ane_cr_lose() with !drm_dp_clock_recovery_ok()
Changes in V3:
-- return failed if lane_count <= 1
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1628196295-7382-3-git-send-email-khsieh@codeaurora.org
[remove unused cr_status variable]
Signed-off-by: Rob Clark <robdclark@chromium.org>
DP cable should always connect to DPU during the entire PHY compliance
testing run. Since DP PHY compliance test is executed at irq_hpd event
context, dp_ctrl_off_link_stream() should be used instead of dp_ctrl_off().
dp_ctrl_off() is used for unplug event which is triggered when DP cable is
dis connected.
Changes in V2:
-- add fixes statement
Fixes: f21c8a276c ("drm/msm/dp: handle irq_hpd with sink_count = 0 correctly")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1628196295-7382-2-git-send-email-khsieh@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The proper spelling for the acronym referring to the Edge/Level Control
Register is ELCR rather than ECLR. Adjust references accordingly. No
functional change.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107200251080.9461@angie.orcam.me.uk
Define PIC_ELCR1 and PIC_ELCR2 macros for accesses to the ELCR registers
implemented by many chipsets in their embedded 8259A PIC cores, avoiding
magic numbers that are difficult to handle, and complementing the macros
we already have for registers originally defined with discrete 8259A PIC
implementations. No functional change.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107200237300.9461@angie.orcam.me.uk
The Intel 82426EX ISA Bridge (IB), a part of the Intel 82420EX PCIset,
implements PCI interrupt steering with a PIRQ router in the form of two
PIRQ Route Control registers, available in the PCI configuration space
at locations 0x66 and 0x67 for the PIRQ0# and PIRQ1# lines respectively.
The semantics is the same as with the PIIX router, however it is not
clear if BIOSes use register indices or line numbers as the cookie to
identify PCI interrupts in their routing tables and therefore support
either scheme.
The IB is directly attached to the Intel 82425EX PCI System Controller
(PSC) component of the chipset via a dedicated PSC/IB Link interface
rather than the host bus or PCI. Therefore it does not itself appear in
the PCI configuration space even though it responds to configuration
cycles addressing registers it implements. Use 82425EX's identification
then for determining the presence of the IB.
References:
[1] "82420EX PCIset Data Sheet, 82425EX PCI System Controller (PSC) and
82426EX ISA Bridge (IB)", Intel Corporation, Order Number:
290488-004, December 1995, Section 3.3.18 "PIRQ1RC/PIRQ0RC--PIRQ
Route Control Registers", p. 61
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107200213490.9461@angie.orcam.me.uk
The Intel 82374EB/82374SB EISA System Component (ESC) devices implement
PCI interrupt steering with a PIRQ router[1] in the form of four PIRQ
Route Control registers, available in the port I/O space accessible
indirectly via the index/data register pair at 0x22/0x23, located at
indices 0x60/0x61/0x62/0x63 for the PIRQ0/1/2/3# lines respectively.
The semantics is the same as with the PIIX router, however it is not
clear if BIOSes use register indices or line numbers as the cookie to
identify PCI interrupts in their routing tables and therefore support
either scheme.
Accesses to the port I/O space concerned here need to be unlocked by
writing the value of 0x0f to the ESC ID Register at index 0x02
beforehand[2]. Do so then and then lock access after use for safety.
This locking could possibly interfere with accesses to the Intel MP spec
IMCR register, implemented by the 82374SB variant of the ESC only as the
PCI/APIC Control Register at index 0x70[3], for which leaving access to
the configuration space concerned unlocked may have been a requirement
for the BIOS to remain compliant with the MP spec. However we only poke
at the IMCR register if the APIC mode is used, in which case the PIRQ
router is not, so this arrangement is not going to interfere with IMCR
access code.
The ESC is implemented as a part of the combined southbridge also made
of 82375EB/82375SB PCI-EISA Bridge (PCEB) and does itself appear in the
PCI configuration space. Use the PCEB's device identification then for
determining the presence of the ESC.
References:
[1] "82374EB/82374SB EISA System Component (ESC)", Intel Corporation,
Order Number: 290476-004, March 1996, Section 3.1.12
"PIRQ[0:3]#--PIRQ Route Control Registers", pp. 44-45
[2] same, Section 3.1.1 "ESCID--ESC ID Register", p. 36
[3] same, Section 3.1.17 "PAC--PCI/APIC Control Register", p. 47
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107192023450.9461@angie.orcam.me.uk
The ALi M1487 ISA Bus Controller (IBC), a part of the ALi FinALi 486
chipset, implements PCI interrupt steering with a PIRQ router[1] in the
form of four 4-bit mappings, spread across two PCI INTx Routing Table
Mapping Registers, available in the port I/O space accessible indirectly
via the index/data register pair at 0x22/0x23, located at indices 0x42
and 0x43 for the INT1/INT2 and INT3/INT4 lines respectively.
Additionally there is a separate PCI INTx Sensitivity Register at index
0x44 in the same port I/O space, whose bits 3:0 select the trigger mode
for INT[4:1] lines respectively[2]. Manufacturer's documentation says
that this register has to be set consistently with the relevant ELCR
register[3]. Add a router-specific hook then and use it to handle this
register.
Accesses to the port I/O space concerned here need to be unlocked by
writing the value of 0xc5 to the Lock Register at index 0x03
beforehand[4]. Do so then and then lock access after use for safety.
The IBC is implemented as a peer bridge on the host bus rather than a
southbridge on PCI and therefore it does not itself appear in the PCI
configuration space. It is complemented by the M1489 Cache-Memory PCI
Controller (CMP) host-to-PCI bridge, so use that device's identification
for determining the presence of the IBC.
References:
[1] "M1489/M1487: 486 PCI Chip Set", Version 1.2, Acer Laboratories
Inc., July 1997, Section 4: "Configuration Registers", pp. 76-77
[2] same, p. 77
[3] same, Section 5: "M1489/M1487 Software Programming Guide", pp.
99-100
[4] same, Section 4: "Configuration Registers", p. 37
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107191702020.9461@angie.orcam.me.uk
Define macros and accessors for the configuration space addressed
indirectly with an index register and a data register at the port I/O
locations of 0x22 and 0x23 respectively.
This space is defined by the Intel MultiProcessor Specification for the
IMCR register used to switch between the PIC and the APIC mode[1], by
Cyrix processors for their configuration[2][3], and also some chipsets.
Given the lack of atomicity with the indirect addressing a spinlock is
required to protect accesses, although for Cyrix processors it is enough
if accesses are executed with interrupts locally disabled, because the
registers are local to the accessing CPU, and IMCR is only ever poked at
by the BSP and early enough for interrupts not to have been configured
yet. Therefore existing code does not have to change or use the new
spinlock and neither it does.
Put the spinlock in a library file then, so that it does not get pulled
unnecessarily for configurations that do not refer it.
Convert Cyrix accessors to wrappers so as to retain the brevity and
clarity of the `getCx86' and `setCx86' calls.
References:
[1] "MultiProcessor Specification", Version 1.4, Intel Corporation,
Order Number: 242016-006, May 1997, Section 3.6.2.1 "PIC Mode", pp.
3-7, 3-8
[2] "5x86 Microprocessor", Cyrix Corporation, Order Number: 94192-00,
July 1995, Section 2.3.2.4 "Configuration Registers", p. 2-23
[3] "6x86 Processor", Cyrix Corporation, Order Number: 94175-01, March
1996, Section 2.4.4 "6x86 Configuration Registers", p. 2-23
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107182353140.9461@angie.orcam.me.uk
'of_find_device_by_node()' takes a reference that must be released when
not needed anymore.
This is expected to be done in 'dsi_destroy()'.
However, there are 2 issues in 'dsi_get_phy()'.
First, if 'of_find_device_by_node()' succeeds but 'platform_get_drvdata()'
returns NULL, 'msm_dsi->phy_dev' will still be NULL, and the reference
won't be released in 'dsi_destroy()'.
Secondly, as 'of_find_device_by_node()' already takes a reference, there is
no need for an additional 'get_device()'.
Move the assignment to 'msm_dsi->phy_dev' a few lines above and remove the
unneeded 'get_device()' to solve both issues.
Fixes: ec31abf668 ("drm/msm/dsi: Separate PHY to another platform device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f15bc57648a00e7c99f943903468a04639d50596.1628241097.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Rob Clark <robdclark@chromium.org>
This check is really about which SQE firmware, rather than which GPU.
Rework to match minimum version based on firmware name, so it doesn't
need to be updated when adding additional GPUs using the same fw.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210807163019.379003-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
As the documentation states, "The exact license information can only be
determined via the license information in the corresponding source files."
and the SPDX identifier has the proper information.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210810212008.631359-1-alexandre.belloni@bootlin.com
This was pointed out with the recent name change of or32_early_setup to
or1k_early_setup. Investigating the file I found a few other warnings
so cleaning them up here.
arch/openrisc/kernel/setup.c:220:13: warning: no previous prototype for 'or1k_early_setup' [-Wmissing-prototypes]
220 | void __init or1k_early_setup(void *fdt)
| ^~~~~~~~~~~~~~~~
Fix this the missing or1k_early_setup prototype warning by adding an
asm/setup.h file to define the prototype.
arch/openrisc/kernel/setup.c:246:13: warning: no previous prototype for 'detect_unit_config' [-Wmissing-prototypes]
246 | void __init detect_unit_config(unsigned long upr, unsigned long mask,
| ^~~~~~~~~~~~~~~~~~
The function detect_unit_config is not used, just remove it.
arch/openrisc/kernel/setup.c:221: warning: Function parameter or member 'fdt' not described in 'or1k_early_setup'
Add @fdt docs to the function comment to suppress this warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Remove #define CONFIG_PM and use __maybe_unused for PM functions and
pm_ptr() for PM ops.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Switch to use module_parport_driver() to reduce boilerplate code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Append i2c-sysfs to toctree in order to get rid of building warnings.
Fixes: 31df7195b1 ("Documentation: i2c: Add doc for I2C sysfs")
Signed-off-by: Hu Haowen <src.res@email.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If an i2c driver happens to not provide the full amount of data that a
user asks for, it is possible that some uninitialized data could be sent
to userspace. While all in-kernel drivers look to be safe, just be sure
by initializing the buffer to zero before it is passed to the i2c driver
so that any future drivers will not have this issue.
Also properly copy the amount of data recvieved to the userspace buffer,
as pointed out by Dan Carpenter.
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Describe the arguments correctly.
Fixes the following W=1 kernel build warning(s):
kernel/irq/matrix.c:287: warning: Function parameter or
member 'msk' not described in 'irq_matrix_alloc_managed'
kernel/irq/matrix.c:287: warning: Function parameter or
member 'mapped_cpu' not described in 'irq_matrix_alloc_managed'
kernel/irq/matrix.c:287: warning: Excess function
parameter 'cpu' description in 'irq_matrix_alloc_managed'
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210605063413.684085-1-libaokun1@huawei.com
With CONFIG_IRQ_FORCED_THREADING=y, testing the boolean force_irqthreads
could incur a cache line miss in invoke_softirq() and other places.
Replace the test with a static key to avoid the potential cache miss.
[ tglx: Dropped the IDE part, removed the export and updated blk-mq ]
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tanner Love <tannerlove@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210602180338.3324213-1-tannerlove.kernel@gmail.com
If a user is interested in such details he can enable smbus tracing.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
p2sb_spinlock is used in i801_add_tco_spt() only, and in process context
only. Therefore a mutex is sufficient, and we can make the definition
local to i801_add_tco_spt().
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Setting the autosuspend delay to a negative value disables runtime pm in
a little bit smarter way, because we need no cleanup when removing the
driver. Note that this is safe when reloading the driver, because the
call to pm_runtime_set_autosuspend_delay() in probe() will reverse the
effect. See update_autosuspend() for details.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The blamed commit added a new field to struct switchdev_notifier_fdb_info,
but did not make sure that all call paths set it to something valid.
For example, a switchdev driver may emit a SWITCHDEV_FDB_ADD_TO_BRIDGE
notifier, and since the 'is_local' flag is not set, it contains junk
from the stack, so the bridge might interpret those notifications as
being for local FDB entries when that was not intended.
To avoid that now and in the future, zero-initialize all
switchdev_notifier_fdb_info structures created by drivers such that all
newly added fields to not need to touch drivers again.
Fixes: 2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB notifications")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20210810115024.1629983-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
pull-request: mlx5-next 2020-08-9
This pulls mlx5-next branch which includes patches already reviewed on
net-next and rdma mailing lists.
1) mlx5 single E-Switch FDB for lag
2) IB/mlx5: Rename is_apu_thread_cq function to is_apu_cq
3) Add DCS caps & fields support
[1] https://patchwork.kernel.org/project/netdevbpf/cover/20210803231959.26513-1-saeed@kernel.org/
[2] https://patchwork.kernel.org/project/netdevbpf/patch/0e3364dab7e0e4eea5423878b01aa42470be8d36.1626609184.git.leonro@nvidia.com/
[3] https://patchwork.kernel.org/project/netdevbpf/patch/55e1d69bef1fbfa5cf195c0bfcbe35c8019de35e.1624258894.git.leonro@nvidia.com/
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Lag, Create shared FDB when in switchdev mode
net/mlx5: E-Switch, add logic to enable shared FDB
net/mlx5: Lag, move lag destruction to a workqueue
net/mlx5: Lag, properly lock eswitch if needed
net/mlx5: Add send to vport rules on paired device
net/mlx5: E-Switch, Add event callback for representors
net/mlx5e: Use shared mappings for restoring from metadata
net/mlx5e: Add an option to create a shared mapping
net/mlx5: E-Switch, set flow source for send to uplink rule
RDMA/mlx5: Add shared FDB support
{net, RDMA}/mlx5: Extend send to vport rules
RDMA/mlx5: Fill port info based on the relevant eswitch
net/mlx5: Lag, add initial logic for shared FDB
net/mlx5: Return mdev from eswitch
IB/mlx5: Rename is_apu_thread_cq function to is_apu_cq
net/mlx5: Add DCS caps & fields support
====================
Link: https://lore.kernel.org/r/20210809202522.316930-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Memory devices may specify volatile only, persistent only, and
partitionable space which when added together result in a total capacity.
If Identify Memory Device.Partition Alignment != 0 the device supports
partitionable space. This partitionable space can be split between
volatile and persistent space. The total volatile and persistent sizes
are reported in Get Partition Info. ie
active volatile memory = volatile only + partitionable volatile
active persistent memory = persistent only + partitionable persistent
Define cxl_mem_get_partition(), check for partitionable support, and use
cxl_mem_get_partition() if applicable.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Ignore fdb flags when adding port extern learn entries and always set
BR_FDB_LOCAL flag when adding bridge extern learn entries. This is
closest to the behaviour we had before and avoids breaking any use cases
which were allowed.
This patch fixes iproute2 calls which assume NUD_PERMANENT and were
allowed before, example:
$ bridge fdb add 00:11:22:33:44:55 dev swp1 extern_learn
Extern learn entries are allowed to roam, but do not expire, so static
or dynamic flags make no sense for them.
Also add a comment for future reference.
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Fixes: 0541a62932 ("net: bridge: validate the NUD_PERMANENT bit when adding an extern_learn FDB entry")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210810110010.43859-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some USB BT adapters don't satisfy the MTU requirement mentioned in
commit e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
and have ALT 3 setting that produces no/garbled audio. Some adapters
with larger MTU were also reported to have problems with ALT 3.
Add a flag and check it and MTU before selecting ALT 3, falling back to
ALT 1. Enable the flag for Realtek, restoring the previous behavior for
non-Realtek devices.
Tested with USB adapters (mtu<72, no/garbled sound with ALT3, ALT1
works) BCM20702A1 0b05:17cb, CSR8510A10 0a12:0001, and (mtu>=72, ALT3
works) RTL8761BU 0bda:8771, Intel AX200 8087:0029 (after disabling
ALT6). Also got reports for (mtu>=72, ALT 3 reported to produce bad
audio) Intel 8087:0a2b.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Fixes: e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
Tested-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Jonathan Lampérth <jon@h4n.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Update JSON metrics for SkyLake Server.
Based on TMA metrics 4.21 at 01.org.
https://download.01.org/perfmon/
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https //lore.kernel.org/r/20210810020508.31261-7-yao.jin@linux.intel.com
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Update JSON uncore events for SkyLake Server.
Based on JSON list v1.24:
https://download.01.org/perfmon/SKX/
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https //lore.kernel.org/r/20210810020508.31261-6-yao.jin@linux.intel.com
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
When two devices with same SID are getting probed concurrently through
iommu_probe_device(), the iommu_group sometimes is getting allocated more
than once as call to arm_smmu_device_group() is not protected for
concurrency. Furthermore, it leads to each device holding a different
iommu_group and domain pointer, separate IOVA space and only one of the
devices' domain is used for translations from IOMMU. This causes accesses
from other device to fault or see incorrect translations.
Fix this by protecting iommu_group allocation from concurrency in
arm_smmu_device_group().
Signed-off-by: Krishna Reddy <vdumpa@nvidia.com>
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Link: https://lore.kernel.org/r/1628570641-9127-3-git-send-email-amhetre@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
When two devices with same SID are getting probed concurrently through
iommu_probe_device(), the iommu_domain sometimes is getting allocated more
than once as call to iommu_alloc_default_domain() is not protected for
concurrency. Furthermore, it leads to each device holding a different
iommu_domain pointer, separate IOVA space and only one of the devices'
domain is used for translations from IOMMU. This causes accesses from other
device to fault or see incorrect translations.
Fix this by protecting iommu_alloc_default_domain() call with group->mutex
and let all devices with same SID share same iommu_domain.
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Link: https://lore.kernel.org/r/1628570641-9127-2-git-send-email-amhetre@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
Update JSON core events for SkyLake Server.
Based on JSON list v1.24:
https://download.01.org/perfmon/SKX/
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https //lore.kernel.org/r/20210810020508.31261-5-yao.jin@linux.intel.com
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Update JSON metrics for CascadeLake Server.
Based on TMA metrics 4.21 at 01.org.
https://download.01.org/perfmon/
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linux-kernel@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https //lore.kernel.org/r/20210810020508.31261-4-yao.jin@linux.intel.com
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Currently inter-server copy is allowed only if the copy size is larger
than (rsize*14) which is the over-head of the mount operation of the
source export. This patch, relying on the delayed unmount feature,
removes this restriction since the mount and unmount overhead is now
not applicable for every inter-server copy.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The xdr_stream and rq_arg and rq_res are already accessible via the
@rqstp parameter.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Move the xdr_init_encode() and xdr_init_decode() calls
into the dispatcher, just like the NFSD and lockd dispatchers.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: The callback RPC dispatcher no longer invokes these call
outs, although svc_process_common() relies on seeing a .pc_encode
function.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The client's NFSv4 callback service is the only remaining user of
svc_generic_dispatch().
Note that the NFSv4 callback service doesn't use the .pc_encode and
.pc_decode callouts in any substantial way, so they are removed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Now that there is an alternate method for returning an auth_stat
value, replace the RQ_AUTHERR flag with use of that new method.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
In a few moments, rq_auth_stat will need to be explicitly set to
rpc_auth_ok before execution gets to the dispatcher.
svc_authenticate() already sets it, but it often gets reset to
rpc_autherr_badcred right after that call, even when authentication
is successful. Let's ensure that the pg_authenticate callout and
svc_set_client() set it properly in every case.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I'd like to take commit 4532608d71 ("SUNRPC: Clean up generic
dispatcher code") even further by using only private local SVC
dispatchers for all kernel RPC services. This change would enable
the removal of the logic that switches between
svc_generic_dispatch() and a service's private dispatcher, and
simplify the invocation of the service's pc_release method
so that humans can visually verify that it is always invoked
properly.
All that will come later.
First, let's provide a better way to return authentication errors
from SVC dispatcher functions. Instead of overloading the dispatch
method's *statp argument, add a field to struct svc_rqst that can
hold an error value.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Hide the DRM midlayer behind CONFIG_DRM_LEGACY, make functions use
the prefix drm_legacy_, and move declarations to drm_legacy.h.
In struct drm_device, move the fields irq and irq_enabled behind
CONFIG_DRM_LEGACY.
All callers have been updated.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210803090704.32152-15-tzimmermann@suse.de
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
DRM IRQ callbacks are now being called directly or inlined.
Calls to platform_get_irq() can fail with a negative errno code.
Abort initialization in this case. The DRM IRQ midlayer does not
handle this case correctly.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210803090704.32152-13-tzimmermann@suse.de
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
DRM IRQ callbacks are now being called directly or inlined.
Calls to platform_get_irq() can fail with a negative errno code.
Abort initialization in this case. The DRM IRQ midlayer does not
handle this case correctly.
For most drivers, only the DRM IRQ helpers use irq_enabled from
struct drm_device. Tilcdc also uses irq_enabled to make its error
rollback work correctly. As the field will become legacy, duplicated
the state in the driver's local private structure.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210803090704.32152-12-tzimmermann@suse.de
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
DRM IRQ callbacks are now being called directly or inlined.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210803090704.32152-11-tzimmermann@suse.de