General Electric Healthcare's PPD has a secondary processor from
NXP's Kinetis K20 series. That device has two SPI chip selects:
The main interface's behaviour depends on the loaded firmware
and is currently unused.
The secondary interface can be used to update the firmware using
EzPort protocol. This is implemented by this driver using the
kernel's firmware API. The firmware is being flashed into
non-volatile flash memory, so it is enough to flash it once
and not on every boot. Flashing will wear the flash memory
(it has a life time of at least 10k programming cycles). At
the same time only occasional FW updates are expected (like e.g.
a BIOS update). Thus the firmware update is triggered via sysfs
instead of doing it in the driver's probe routine like many
other drivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-4-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PPD has only one ACHC device, which effectively is a Kinetis
microcontroller. It has one SPI interface used for normal
communication. Additionally it's possible to flash the device
firmware using NXP's EzPort protocol by correctly driving a
second chip select pin and the device reset pin.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-3-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the binding to DT schema format. Also update the binding
to fix shortcomings
* Add "nxp,kinetis-k20" fallback compatible
* add programming SPI interface and reset GPIO
* add main clock
* add voltage supplies
* drop spi-max-frequency from required properties,
driver will setup max. frequency
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-2-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the case if dev is NULL in dev_{put, hold}, so the caller doesn't
need to care whether dev is NULL or not.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve error message to be more descriptive if a failure occurs
with an invalid power up execution environment. Additionally, add
a debug log to print the execution environment and MHI state
before a power up is attempted to confirm if the device is in an
expected state. This helps clarify reasons for power up failures
such as the device being found in a PBL or Emergency Download
Mode execution environment and the host expected a full power up
with Pass-Through and no image loading involved.
Link: https://lore.kernel.org/r/1620072038-36160-1-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is nothing special done within the mhi_alloc_coherent() and
the mhi_free_coherent() wrapper functions. They only directly
call the equivalent DMA allocation functions. Replace them with
the original function calls such that the implementation is clear
and direct.
Link: https://lore.kernel.org/r/1624392428-9328-1-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When obtaining the BHI or BHIe offsets during the power up
preparation phase, range checks are missing. These can help
controller drivers avoid accessing any address outside of the
MMIO region. Ensure that mhi_cntrl->reg_len is set before MHI
registration as it is a required field and range checks will
fail without it.
Link: https://lore.kernel.org/r/1620330705-40192-7-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI driver requires register space length to add range checks and
prevent memory region accesses outside of that for MMIO space.
Set it from the PCI generic controller driver before registering
the MHI controller.
Link: https://lore.kernel.org/r/1620330705-40192-6-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI driver requires register space length to add range checks and
prevent memory region accesses outside of that for MMIO space.
Set it before registering the MHI controller.
Link: https://lore.kernel.org/r/1620330705-40192-5-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make controller driver specify the MMIO register region length
for range checking of BHI or BHIe space. This can help validate
that offsets are in acceptable memory region or not and avoid any
boot-up issues due to BHI or BHIe memory accesses.
Link: https://lore.kernel.org/r/1620330705-40192-4-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the BHI and BHIe pointers to NULL as part of clean-up. This
makes sure that stale pointers are not accessed after powering
MHI down.
Link: https://lore.kernel.org/r/1620330705-40192-3-git-send-email-bbhatt@codeaurora.org
Suggested-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the BHI and/or BHIe offsets in mhi_prepare_for_power_up(),
rearrange the function, and remove the equivalent from
mhi_async_power_up(). This helps consolidate multiple checks
in different parts of the driver and can help MHI fail early on
before power up begins if the offsets are not read correctly.
Link: https://lore.kernel.org/r/1620330705-40192-2-git-send-email-bbhatt@codeaurora.org
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the MHI controller driver defines which channels should
have their inbound buffers allocated and queued. But ideally, this is
something that should be decided by the MHI device driver instead,
which actually deals with that buffers.
Add a flag parameter to mhi_prepare_for_transfer allowing to specify
if buffers have to be allocated and queued by the MHI stack.
Keep auto_queue flag for now, but should be removed at some point.
Link: https://lore.kernel.org/r/1624566520-20406-1-git-send-email-loic.poulain@linaro.org
Tested-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210802051255.5771-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'if (dev)' statement already move into dev_{put , hold}, so remove
redundant if statements.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Tegra186 and later, a portion of the SYSRAM may be reserved for use
by TZ. Non-TZ memory accesses to this portion, including speculative
accesses, trigger SErrors that bring down the system. This does also
happen in practice occasionally (due to speculative accesses).
To fix the issue, add a flag to the SRAM driver to only map the
device tree-specified reserved areas depending on a flag set
based on the compatibility string. This would not affect non-Tegra
systems that rely on the entire thing being memory mapped.
If 64K pages are being used, we cannot exactly map the 4K regions
that are placed in SYSRAM - ioremap code instead aligns to closest
64K pages. However, since in practice the non-accessible memory area
is 64K aligned, these mappings do not overlap with the non-accessible
memory area and things work out.
Reviewed-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20210715103423.1811101-1-mperttunen@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FPGA Manager
- Colin's change is a simple spelling cleanup.
DFL
- Martin's fist change exposes DFL feature revision to client drivers
- Martin's second change modifies a SPI driver to populate different
spi_board_info modaliases based on the DFL feature revision
All patches have been reviewed on the mailing list, and have been in the
last few linux-next releases (as part of my for-next branch) without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSdhnt2PwibB65UG0C3mJX/Vsn7uQUCYQqyeQAKCRC3mJX/Vsn7
uQBCAP9JAcGZf6Rd1uV6Y9P0jpAvnsRA5AnwpXT5Vmo3qAtGqwD8DK+19sdN5gIk
vUdicT7mH8ZO6OSIDxNg3/kXHgG69Ac=
=qlgw
-----END PGP SIGNATURE-----
Merge tag 'fpga-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga into char-misc-next
Moritz writes:
FPGA Manager changes for 5.15-rc1
FPGA Manager
- Colin's change is a simple spelling cleanup.
DFL
- Martin's fist change exposes DFL feature revision to client drivers
- Martin's second change modifies a SPI driver to populate different
spi_board_info modaliases based on the DFL feature revision
All patches have been reviewed on the mailing list, and have been in the
last few linux-next releases (as part of my for-next branch) without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
* tag 'fpga-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
spi: spi-altera-dfl: support n5010 feature revision
fpga: dfl: expose feature revision from struct dfl_device
fpga: Fix spelling mistake "eXchnage" -> "exchange" in Kconfig
After commit 85143bdc73 ("staging: r8188eu: include: Remove unused
const definitions"), some comments are not anymore needed. Remove them
too. In the while, remove also a line with a void comment.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20210805120609.28588-1-fmdefrancesco@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coco Li says:
====================
GRO and Toeplitz hash selftests
This patch contains two selftests in net, as well as respective
scripts to run the tests on a single machine in loopback mode.
GRO: tests the Linux kernel GRO behavior
Toeplitz: tests the toeplitz hash implementation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To verify that this hash implements the Toeplitz hash function.
Additionally, provide a script toeplitz.sh to run the test in loopback mode
on a networking device of choice (see setup_loopback.sh). Since the
script modifies the NIC setup, it will not be run by selftests
automatically.
Tested:
./toeplitz.sh -i eth0 -irq_prefix <eth0_pattern> -t -6
carrier ready
rxq 0: cpu 14
rxq 1: cpu 20
rxq 2: cpu 17
rxq 3: cpu 23
cpu 14: rx_hash 0x69103ebc [saddr fda8::2 daddr fda8::1 sport 58938 dport 8000] OK rxq 0 (cpu 14)
...
cpu 20: rx_hash 0x257118b9 [saddr fda8::2 daddr fda8::1 sport 59258 dport 8000] OK rxq 1 (cpu 20)
count: pass=111 nohash=0 fail=0
Test Succeeded!
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a GRO testsuite that expects Linux kernel GRO behavior.
All tests pass with the kernel software GRO stack. Run against a device
with hardware GRO to verify that it matches the software stack.
gro.c generates packets and sends them out through a packet socket. The
receiver in gro.c (run separately) receives the packets on a packet
socket, filters them by destination ports using BPF and checks the
packet geometry to see whether GRO was applied.
gro.sh provides a wrapper to run the gro.c in NIC loopback mode.
It is not included in continuous testing because it modifies network
configuration around a physical NIC: gro.sh sets the NIC in loopback
mode, creates macvlan devices on the physical device in separate
namespaces, and sends traffic generated by gro.c between the two
namespaces to observe coalescing behavior.
GRO coalescing is time sensitive.
Some tests may prove flaky on some hardware.
Note that this test suite tests for software GRO unless hardware GRO is
enabled (ethtool -K $DEV rx-gro-hw on).
To test, run ./gro.sh.
The wrapper will output success or failed test names, and generate
log.txt and stderr.
Sample log.txt result:
...
pure data packet of same size: Test succeeded
large data packets followed by a smaller one: Test succeeded
small data packets followed by a larger one: Test succeeded
...
Sample stderr result:
...
carrier ready
running test ipv4 data
Expected {200 }, Total 1 packets
Received {200 }, Total 1 packets.
...
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma section name is confusing, since the code which resides within
that section has nothing to do with direct memory access. Instead the
limitation is that the code has to run in 31 bit addressing mode, and
therefore has to reside below 2GB. So the name was chosen since
ZONE_DMA is the same region.
To reduce confusion rename the section to amode31, which hopefully
describes better what this is about.
Note: this will also change vmcoreinfo strings
- SDMA=... gets renamed to SAMODE31=...
- EDMA=... gets renamed to EAMODE31=...
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Fix virtual vs physical address confusion (which currently are the same).
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-6-bigeasy@linutronix.de
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-5-bigeasy@linutronix.de
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases we want to specify overrun-throttle like other 8250 drivers
are doing.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit bcf637f54f ("kbuild: parse C= and M= before changing the
working directory"), external module builds invoked by DKMS fail because
M= option is not parsed.
I wanted to add 'unset sub_make_done' in install.sh but similar scripts,
arch/*/boot/install.sh, are duplicated, so I set sub_make_done empty in
the top Makefile.
Fixes: bcf637f54f ("kbuild: parse C= and M= before changing the working directory")
Reported-by: John S Gruber <johnsgruber@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: John S Gruber <johnsgruber@gmail.com>
Update scripts/checkversion.pl to recognize the current contents
of <linux/version.h> and both of its current locations.
Also update my email address.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
When cross compiling a MIPS kernel on a BSD based HOSTCC leads
to errors like
SYNC include/config/auto.conf.cmd - due to: .config
egrep: empty (sub)expression
UPD include/config/kernel.release
HOSTCC scripts/dtc/dtc.o - due to target missing
It turns out that egrep uses this egrep pattern:
(|MINOR_|PATCHLEVEL_)
This is not valid syntax or gives undefined results according
to POSIX 9.5.3 ERE Grammar
https://pubs.opengroup.org/onlinepubs/9699919799/basedefs/V1_chap09.html
It seems to be silently accepted by the Linux egrep implementation
while a BSD host complains.
Such patterns can be replaced by a transformation like
"(|p1|p2)" -> "(p1|p2)?"
Fixes: 48c35b2d24 ("[MIPS] There is no __GNUC_MAJOR__")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Trying to run a cross-compiled x86 relocs tool on a BSD based
HOSTCC leads to errors like
VOFFSET arch/x86/boot/compressed/../voffset.h - due to: vmlinux
CC arch/x86/boot/compressed/misc.o - due to: arch/x86/boot/compressed/../voffset.h
OBJCOPY arch/x86/boot/compressed/vmlinux.bin - due to: vmlinux
RELOCS arch/x86/boot/compressed/vmlinux.relocs - due to: vmlinux
empty (sub)expressionarch/x86/boot/compressed/Makefile:118: recipe for target 'arch/x86/boot/compressed/vmlinux.relocs' failed
make[3]: *** [arch/x86/boot/compressed/vmlinux.relocs] Error 1
It turns out that relocs.c uses patterns like
"something(|_end)"
This is not valid syntax or gives undefined results according
to POSIX 9.5.3 ERE Grammar
https://pubs.opengroup.org/onlinepubs/9699919799/basedefs/V1_chap09.html
It seems to be silently accepted by the Linux regexp() implementation
while a BSD host complains.
Such patterns can be replaced by a transformation like
"(|p1|p2)" -> "(p1|p2)?"
Fixes: fd95281530 ("x86-32, relocs: Whitelist more symbols for ld bug workaround")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Although irq_create_mapping() is able to deal with duplicate
mappings, it really isn't supposed to be a substitute for
irq_find_mapping(), and can result in allocations that take place
in atomic context if the mapping didn't exist.
Fix the handful of MFD drivers that use irq_create_mapping() in
interrupt context by using irq_find_mapping() instead.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If CTA_STATUS is present, but CTA_STATUS_MASK is not, then the
mask is automatically set to 'status', so that kernel returns those
entries that have all of the requested bits set.
This makes more sense than using a all-one mask since we'd hardly
ever find a match.
There are no other checks for status bits, so if e.g. userspace
sets impossible combinations it will get an empty dump.
If kernel would reject unknown status bits, then a program that works on
a future kernel that has IPS_FOO bit fails on old kernels.
Same for 'impossible' combinations:
Kernel never sets ASSURED without first having set SEEN_REPLY, but its
possible that a future kernel could do so.
Therefore no sanity tests other than a 0-mask.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ctnetlink dumps can be filtered based on the connmark.
Prepare for status bit filtering by using a named structure and by
moving the mark parsing code to a helper.
Else ctnetlink_alloc_filter size grows a bit too big for my taste
when status handling is added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Remove rtw_mfree_all_stainfo() and the only line of code that calls
it. This function simply takes a spinlock and iterates over a list
with no purpose. That iteration has no side effects.
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210802005517.12815-1-fmdefrancesco@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warnings of casts between incompatible function
types from ‘void (*)(void *)’ to ‘void (*)(long unsigned int)’
[-Wcast-function-type].
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20210804143218.13665-1-fmdefrancesco@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the initialization of the variable "i" since it is written a few
lines later.
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210801085155.3170-3-len.baker@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy() but in
this case it is simpler to use the "%*ph" format specifier.
Moreover, with the "0x%02X " in the sprintf followed by the strcat, the
msg buffer (now removed) can print 128/5 values (25 hex values). So, the
"%*ph" replacement won't cut output earlier than requested since this
format specifier can print up to 64 bytes.
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210801085155.3170-2-len.baker@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following checkpatch.pl errors:
ERROR: do not initialise globals to {0,NULL}
Signed-off-by: Scott J. Crouch <scottjcrouch@gmail.com>
Link: https://lore.kernel.org/r/20210804001335.16742-1-scottjcrouch@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource() internally calls __devm_ioremap_resource() which
is where error checking and handling is actually taking place. i
Therefore, the dev_err() call in xgene_msi_probe() is redundant.
Remove it.
Link: https://lore.kernel.org/r/20210408132751.1198171-1-yangerkun@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ErKun Yang <yangerkun@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Commit 453431a549 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
it should be applied to coccinelle.
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Denis Efremov <efremov@linux.com>
Remove RT_TRACE macro calls from hal/usb_ops_linux.c, so that ultimately the
macro definition itself can eventually be removed.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210803230535.74254-9-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove RT_TRACE macro calls from hal/usb_halinit.c, so that ultimately the
macro definition itself can eventually be removed.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210803230535.74254-8-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove RT_TRACE macro calls from hal/rtl8188e_mp.c, so that ultimately the
macro definition itself can eventually be removed.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210803230535.74254-7-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove RT_TRACE macro calls from hal/rtl8188e_hal_init.c, so that ultimately
the macro definition itself can eventually be removed.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210803230535.74254-6-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove RT_TRACE macro calls from hal/hal_intf.c, so that ultimately the
macro definition itself can eventually be removed.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210803230535.74254-5-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>